user/sven/linux.git/include/linux/usb/tegra_usb_phy.h, branch v4.14.15

usb: phy: tegra: Program new PHY parameters

2013-08-12T18:29:52Z

The Tegra30 TRM recommends configuration of certain PHY parameters for optimal quality. Program the following registers based on device tree parameters: - UTMIP_XCVR_HSSLEW: HS slew rate control. - UTMIP_HSSQUELCH_LEVEL: HS squelch detector level - UTMIP_HSDISCON_LEVEL: HS disconnect detector level. These registers exist in Tegra20, but programming them hasn't been necessary, so these parameters won't be set on Tegra20 to keep the device trees backward compatible. Additionally, the UTMIP_XCVR_SETUP parameter can be set from fuses instead of a software-programmed value, as the optimal value can vary between invidual boards. The boolean property nvidia,xcvr-setup-use-fuses can be used to enable this behaviour. Signed-off-by: Tuomas Tynkkynen Tested-by: Stephen Warren Reviewed-by: Stephen Warren Signed-off-by: Felipe Balbi

usb: phy: tegra: Tegra30 support

2013-08-12T18:29:48Z

The Tegra30 USB PHY is a bit different than the Tegra20 PHY: - The EHCI controller supports the HOSTPC register extension, and some of the fields that the PHY needs to modify (PHCD and PTS) have moved to the new HOSTPC register. - Some of the UTMI PLL configuration registers have moved from the USB register space to the Clock-And-Reset controller space. In Tegra30 the clock driver is responsible for configuring the UTMI PLL. - The USBMODE register must be explicitly written to enter host mode. - Certain PHY parameters need to be programmed for optimal signal quality. Support for this will be added in the next patch. The new tegra_phy_soc_config structure is added to describe the differences between the SoCs. Signed-off-by: Tuomas Tynkkynen Tested-by: Stephen Warren Reviewed-by: Stephen Warren Signed-off-by: Felipe Balbi

usb: phy: tegra: Use DT helpers for dr_mode

2013-07-29T10:58:27Z

Use the new of_usb_get_dr_mode helper function for parsing dr_mode from the device tree. Also replace the usage of the custom tegra_usb_phy_mode enum with the standard enum. Signed-off-by: Tuomas Tynkkynen Reviewed-by: Stephen Warren Tested-by: Stephen Warren Signed-off-by: Felipe Balbi

usb: phy: tegra: Remove custom PHY locating APIs

2013-07-29T10:58:25Z

The Tegra EHCI driver is no longer using these custom functions, so they can be removed. Signed-off-by: Tuomas Tynkkynen Reviewed-by: Stephen Warren Tested-by: Stephen Warren Signed-off-by: Felipe Balbi

ARM: tegra: Remove USB platform data

2013-07-29T10:58:23Z

USB-related platform data is not used anymore in the Tegra USB drivers, so remove all of it. Signed-off-by: Tuomas Tynkkynen Reviewed-by: Stephen Warren Tested-by: Stephen Warren Acked-by: Stephen Warren Signed-off-by: Felipe Balbi

usb: phy: tegra: Remove unnecessary 'dev' field

2013-07-29T10:58:21Z

struct usb_phy already has a field for the device pointer, so this unnecessary field can be removed. Signed-off-by: Tuomas Tynkkynen Reviewed-by: Stephen Warren Tested-by: Stephen Warren Signed-off-by: Felipe Balbi

usb: tegra: Use regulators instead of GPIOs for USB PHY VBUS

2013-07-29T10:58:18Z

The tegra ehci driver has enabled USB vbus regulators directly using GPIOs and the device tree attribute nvidia,vbus-gpio. This is ugly and causes error messages on boot when both the regulator driver and the ehci driver want access to the same GPIO. After this patch, usb vbus regulators for tegra usb phy devices are specified with the device tree attribute vbus-supply = <&x> where x is a regulator defined in the device tree. The old nvidia,vbus-gpio property is no longer supported. Signed-off-by: Mikko Perttunen Reviewed-by: Stephen Warren Tested-by: Stephen Warren Signed-off-by: Felipe Balbi

USB: EHCI: tegra: fix circular module dependencies

2013-06-17T20:54:48Z

The Tegra EHCI driver directly calls various functions in the Tegra USB PHY driver. The reverse is also true; the PHY driver calls into the EHCI driver. This is problematic when the two are built as modules. The calls from the PHY to EHCI driver were originally added in commit bbdabdb "usb: add APIs to access host registers from Tegra PHY", for the following reasons: 1) The register being touched is an EHCI register, so logically only the EHCI driver should touch it. 2) (1) implies that some locking may be needed to correctly implement the r/m/w access to this shared register. 3) We were expecting to pass only the PHY register space to the Tegra PHY driver, and hence it would not have access to touch the shared registers. To solve this, that commit added functions in the EHCI driver to touch the shared register on behalf of the PHY driver. In practice, we ended up not having any locking in the implementaiton of those functions, and I've been led to believe this is safe. Equally, (3) did not happen either. Hence, it is possible for the PHY driver to touch the shared register directly. Given that, this patch moves the code to touch the shared register back into the PHY driver, to eliminate the module problems. If we actually need locking or co-ordination in the future, I propose we put the lock support into some pre-existing core module, or into a third separate module, in order to avoid the circular dependencies. I apologize for my contribution to code churn here. Signed-off-by: Stephen Warren Acked-by: Alan Stern Acked-by: Arnd Bergmann Tested-by: Thierry Reding Signed-off-by: Greg Kroah-Hartman

usb: phy: registering Tegra USB PHY as platform driver

2013-05-29T23:49:11Z

Registered Tegra USB PHY as a separate platform driver. To synchronize host controller and PHY initialization, used deferred probe mechanism. As PHY should be initialized before EHCI starts running, deferred probe of Tegra EHCI driver till PHY probe gets completed. Got rid of instance number based handling in host driver. Made use of DT params to get the PHY Pad registers. Signed-off-by: Venu Byravarasu Signed-off-by: Felipe Balbi

usb: phy: tegra: get ULPI reset GPIO info using DT.

2013-05-29T23:47:19Z

As GPIO information is avail through DT, used it to get Tegra ULPI reset GPIO number. Added a new member to tegra_usb_phy structure to store this number. Signed-off-by: Venu Byravarasu Signed-off-by: Felipe Balbi