user/sven/linux.git/include/linux/usb, branch v6.1.99

usb: new quirk to reduce the SET_ADDRESS request timeout

2024-04-27T15:07:12Z

[ Upstream commit 5a1ccf0c72cf917ff3ccc131d1bb8d19338ffe52 ] This patch introduces a new USB quirk, USB_QUIRK_SHORT_SET_ADDRESS_REQ_TIMEOUT, which modifies the timeout value for the SET_ADDRESS request. The standard timeout for USB request/command is 5000 ms, as recommended in the USB 3.2 specification (section 9.2.6.1). However, certain scenarios, such as connecting devices through an APTIV hub, can lead to timeout errors when the device enumerates as full speed initially and later switches to high speed during chirp negotiation. In such cases, USB analyzer logs reveal that the bus suspends for 5 seconds due to incorrect chirp parsing and resumes only after two consecutive timeout errors trigger a hub driver reset. Packet(54) Dir(?) Full Speed J(997.100 us) Idle( 2.850 us) _______| Time Stamp(28 . 105 910 682) _______|_____________________________________________________________Ch0 Packet(55) Dir(?) Full Speed J(997.118 us) Idle( 2.850 us) _______| Time Stamp(28 . 106 910 632) _______|_____________________________________________________________Ch0 Packet(56) Dir(?) Full Speed J(399.650 us) Idle(222.582 us) _______| Time Stamp(28 . 107 910 600) _______|_____________________________________________________________Ch0 Packet(57) Dir Chirp J( 23.955 ms) Idle(115.169 ms) _______| Time Stamp(28 . 108 532 832) _______|_____________________________________________________________Ch0 Packet(58) Dir(?) Full Speed J (Suspend)( 5.347 sec) Idle( 5.366 us) _______| Time Stamp(28 . 247 657 600) _______|_____________________________________________________________Ch0 This 5-second delay in device enumeration is undesirable, particularly in automotive applications where quick enumeration is crucial (ideally within 3 seconds). The newly introduced quirks provide the flexibility to align with a 3-second time limit, as required in specific contexts like automotive applications. By reducing the SET_ADDRESS request timeout to 500 ms, the system can respond more swiftly to errors, initiate rapid recovery, and ensure efficient device enumeration. This change is vital for scenarios where rapid smartphone enumeration and screen projection are essential. To use the quirk, please write "vendor_id:product_id:p" to /sys/bus/usb/drivers/hub/module/parameter/quirks For example, echo "0x2c48:0x0132:p" > /sys/bus/usb/drivers/hub/module/parameters/quirks" Signed-off-by: Hardik Gajjar Reviewed-by: Alan Stern Link: https://lore.kernel.org/r/20231027152029.104363-2-hgajjar@de.adit-jv.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

usb: xhci: Add timeout argument in address_device USB HCD callback

2024-04-27T15:07:11Z

[ Upstream commit a769154c7cac037914ba375ae88aae55b2c853e0 ] - The HCD address_device callback now accepts a user-defined timeout value in milliseconds, providing better control over command execution times. - The default timeout value for the address_device command has been set to 5000 ms, aligning with the USB 3.2 specification. However, this timeout can be adjusted as needed. - The xhci_setup_device function has been updated to accept the timeout value, allowing it to specify the maximum wait time for the command operation to complete. - The hub driver has also been updated to accommodate the newly added timeout parameter during the SET_ADDRESS request. Signed-off-by: Hardik Gajjar Reviewed-by: Mathias Nyman Link: https://lore.kernel.org/r/20231027152029.104363-1-hgajjar@de.adit-jv.com Signed-off-by: Greg Kroah-Hartman Stable-dep-of: 5a1ccf0c72cf ("usb: new quirk to reduce the SET_ADDRESS request timeout") Signed-off-by: Sasha Levin

usb: gadget: Properly configure the device for remote wakeup

2024-03-06T14:45:05Z

[ Upstream commit b93c2a68f3d9dc98ec30dcb342ae47c1c8d09d18 ] The wakeup bit in the bmAttributes field indicates whether the device is configured for remote wakeup. But this field should be allowed to set only if the UDC supports such wakeup mechanism. So configure this field based on UDC capability. Also inform the UDC whether the device is configured for remote wakeup by implementing a gadget op. Reviewed-by: Thinh Nguyen Signed-off-by: Elson Roy Serrao Link: https://lore.kernel.org/r/1679694482-16430-2-git-send-email-quic_eserrao@quicinc.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

r8152: add vendor/device ID pair for ASUS USB-C2500

2023-12-20T16:00:14Z

[ Upstream commit 7037d95a047cd89b1f680eed253c6ab586bef1ed ] The ASUS USB-C2500 is an RTL8156 based 2.5G Ethernet controller. Add the vendor and product ID values to the driver. This makes Ethernet work with the adapter. Signed-off-by: Kelly Kane Link: https://lore.kernel.org/r/20231203011712.6314-1-kelly@hawknetworks.com Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

r8152: add vendor/device ID pair for D-Link DUB-E250

2023-12-20T16:00:14Z

[ Upstream commit 72f93a3136ee18fd59fa6579f84c07e93424681e ] The D-Link DUB-E250 is an RTL8156 based 2.5G Ethernet controller. Add the vendor and product ID values to the driver. This makes Ethernet work with the adapter. Signed-off-by: Antonio Napolitano Link: https://lore.kernel.org/r/CV200KJEEUPC.WPKAHXCQJ05I@mercurius Signed-off-by: Jakub Kicinski Stable-dep-of: 7037d95a047c ("r8152: add vendor/device ID pair for ASUS USB-C2500") Signed-off-by: Sasha Levin

usb: chipidea: add workaround for chipidea PEC bug

2023-09-23T09:11:07Z

[ Upstream commit 12e6ac69cc7e7d3367599ae26a92a0f9a18bc728 ] Some NXP processors using ChipIdea USB IP have a bug when frame babble is detected. Issue description: In USB camera test, our controller is host in HS mode. In ISOC IN, when device sends data across the micro frame, it causes the babble in host controller. This will clear the PE bit. In spec, it also requires to set the PEC bit and then set the PCI bit. Without the PCI interrupt, the software does not know the PE is cleared. This will add a flag CI_HDRC_HAS_PORTSC_PEC_MISSED to some impacted platform datas. And the ehci host driver will assert PEC by SW when specific conditions are satisfied. Signed-off-by: Xu Yang Link: https://lore.kernel.org/r/20230809024432.535160-2-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

usb: typec: bus: verify partner exists in typec_altmode_attention

2023-09-13T07:43:04Z

commit f23643306430f86e2f413ee2b986e0773e79da31 upstream. Some usb hubs will negotiate DisplayPort Alt mode with the device but will then negotiate a data role swap after entering the alt mode. The data role swap causes the device to unregister all alt modes, however the usb hub will still send Attention messages even after failing to reregister the Alt Mode. type_altmode_attention currently does not verify whether or not a device's altmode partner exists, which results in a NULL pointer error when dereferencing the typec_altmode and typec_altmode_ops belonging to the altmode partner. Verify the presence of a device's altmode partner before sending the Attention message to the Alt Mode driver. Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes") Cc: stable@vger.kernel.org Signed-off-by: RD Babiera Reviewed-by: Heikki Krogerus Reviewed-by: Guenter Roeck Link: https://lore.kernel.org/r/20230814180559.923475-1-rdbabiera@google.com Signed-off-by: Greg Kroah-Hartman

usb: typec: tcpci: clear the fault status bit

2023-09-06T20:27:03Z

commit 23e60c8daf5ec2ab1b731310761b668745fcf6ed upstream. According the "USB Type-C Port Controller Interface Specification v2.0" the TCPC sets the fault status register bit-7 (AllRegistersResetToDefault) once the registers have been reset to their default values. This triggers an alert(-irq) on PTN5110 devices albeit we do mask the fault-irq, which may cause a kernel hang. Fix this generically by writing a one to the corresponding bit-7. Cc: stable@vger.kernel.org Fixes: 74e656d6b055 ("staging: typec: Type-C Port Controller Interface driver (tcpci)") Reported-by: "Angus Ainslie (Purism)" Closes: https://lore.kernel.org/all/20190508002749.14816-2-angus@akkea.ca/ Reported-by: Christian Bach Closes: https://lore.kernel.org/regressions/ZR0P278MB07737E5F1D48632897D51AC3EB329@ZR0P278MB0773.CHEP278.PROD.OUTLOOK.COM/t/ Signed-off-by: Marco Felsch Signed-off-by: Fabio Estevam Reviewed-by: Guenter Roeck Link: https://lore.kernel.org/r/20230816172502.1155079-1-festevam@gmail.com Signed-off-by: Greg Kroah-Hartman

Revert "usb: common: usb-conn-gpio: Set last role to unknown before initial detection"

2023-07-19T14:21:56Z

[ Upstream commit df49f2a0ac4a34c0cb4b5c233fcfa0add644c43c ] This reverts commit edd60d24bd858cef165274e4cd6cab43bdc58d15. Heikki reports that this should not be a global flag just to work around one broken driver and should be fixed differently, so revert it. Reported-by: Heikki Krogerus Fixes: edd60d24bd85 ("usb: common: usb-conn-gpio: Set last role to unknown before initial detection") Link: https://lore.kernel.org/r/ZImE4L3YgABnCIsP@kuha.fi.intel.com Cc: Prashanth K Cc: AngeloGioacchino Del Regno Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

usb: common: usb-conn-gpio: Set last role to unknown before initial detection

2023-07-19T14:21:55Z

[ Upstream commit edd60d24bd858cef165274e4cd6cab43bdc58d15 ] Currently if we bootup a device without cable connected, then usb-conn-gpio won't call set_role() since last_role is same as current role. This happens because during probe last_role gets initialised to zero. To avoid this, added a new constant in enum usb_role, last_role is set to USB_ROLE_UNKNOWN before performing initial detection. While at it, also handle default case for the usb_role switch in cdns3, intel-xhci-usb-role-switch & musb/jz4740 to avoid build warnings. Fixes: 4602f3bff266 ("usb: common: add USB GPIO based connection detection driver") Signed-off-by: Prashanth K Reviewed-by: AngeloGioacchino Del Regno Message-ID: <1685544074-17337-1-git-send-email-quic_prashk@quicinc.com> Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin