user/sven/linux.git/include/linux, branch v4.4.12

SIGNAL: Move generic copy_siginfo() to signal.h

2016-06-01T19:15:54Z

commit ca9eb49aa9562eaadf3cea071ec7018ad6800425 upstream. The generic copy_siginfo() is currently defined in asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which defines the generic struct siginfo. However this makes it awkward for an architecture to use it if it has to define its own struct siginfo (e.g. MIPS and potentially IA64), since it means that asm-generic/siginfo.h can only be included after defining the arch-specific siginfo, which may be problematic if the arch-specific definition needs definitions from uapi/asm-generic/siginfo.h. It is possible to work around this by first including uapi/asm-generic/siginfo.h to get the constants before defining the arch-specific siginfo, and include asm-generic/siginfo.h after. However uapi headers can't be included by other uapi headers, so that first include has to be in an ifdef __kernel__, with the non __kernel__ case including the non-UAPI header instead. Instead of that mess, move the generic copy_siginfo() definition into linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to include asm-generic/siginfo.h and define the arch-specific siginfo, and for the generic copy_siginfo() to see that arch-specific definition. Signed-off-by: James Hogan Cc: Arnd Bergmann Cc: Ralf Baechle Cc: Petr Malat Cc: Tony Luck Cc: Fenghua Yu Cc: Christopher Ferris Cc: linux-arch@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-ia64@vger.kernel.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/12478/ Signed-off-by: Ralf Baechle Signed-off-by: Greg Kroah-Hartman

Fix OpenSSH pty regression on close

2016-06-01T19:15:52Z

commit 0f40fbbcc34e093255a2b2d70b6b0fb48c3f39aa upstream. OpenSSH expects the (non-blocking) read() of pty master to return EAGAIN only if it has received all of the slave-side output after it has received SIGCHLD. This used to work on pre-3.12 kernels. This fix effectively forces non-blocking read() and poll() to block for parallel i/o to complete for all ttys. It also unwinds these changes: 1) f8747d4a466ab2cafe56112c51b3379f9fdb7a12 tty: Fix pty master read() after slave closes 2) 52bce7f8d4fc633c9a9d0646eef58ba6ae9a3b73 pty, n_tty: Simplify input processing on final close 3) 1a48632ffed61352a7810ce089dc5a8bcd505a60 pty: Fix input race when closing Inspired by analysis and patch from Marc Aurele La France Reported-by: Volth Reported-by: Marc Aurele La France BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=52 BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=2492 Signed-off-by: Brian Bloniarz Reviewed-by: Peter Hurley Signed-off-by: Greg Kroah-Hartman

USB: leave LPM alone if possible when binding/unbinding interface drivers

2016-06-01T19:15:51Z

commit 6fb650d43da3e7054984dc548eaa88765a94d49f upstream. When a USB driver is bound to an interface (either through probing or by claiming it) or is unbound from an interface, the USB core always disables Link Power Management during the transition and then re-enables it afterward. The reason is because the driver might want to prevent hub-initiated link power transitions, in which case the HCD would have to recalculate the various LPM parameters. This recalculation takes place when LPM is re-enabled and the new parameters are sent to the device and its parent hub. However, if the driver does not want to prevent hub-initiated link power transitions then none of this work is necessary. The parameters don't need to be recalculated, and LPM doesn't need to be disabled and re-enabled. It turns out that disabling and enabling LPM can be time-consuming, enough so that it interferes with user programs that want to claim and release interfaces rapidly via usbfs. Since the usbfs kernel driver doesn't set the disable_hub_initiated_lpm flag, we can speed things up and get the user programs to work by leaving LPM alone whenever the flag isn't set. And while we're improving the way disable_hub_initiated_lpm gets used, let's also fix its kerneldoc. Signed-off-by: Alan Stern Tested-by: Matthew Giassa CC: Mathias Nyman Signed-off-by: Greg Kroah-Hartman

can: fix handling of unmodifiable configuration options

2016-06-01T19:15:50Z

commit bb208f144cf3f59d8f89a09a80efd04389718907 upstream. As described in 'can: m_can: tag current CAN FD controllers as non-ISO' (6cfda7fbebe) it is possible to define fixed configuration options by setting the according bit in 'ctrlmode' and clear it in 'ctrlmode_supported'. This leads to the incovenience that the fixed configuration bits can not be passed by netlink even when they have the correct values (e.g. non-ISO, FD). This patch fixes that issue and not only allows fixed set bit values to be set again but now requires(!) to provide these fixed values at configuration time. A valid CAN FD configuration consists of a nominal/arbitration bittiming, a data bittiming and a control mode with CAN_CTRLMODE_FD set - which is now enforced by a new can_validate() function. This fix additionally removed the inconsistency that was prohibiting the support of 'CANFD-only' controller drivers, like the RCar CAN FD. For this reason a new helper can_set_static_ctrlmode() has been introduced to provide a proper interface to handle static enabled CAN controller options. Reported-by: Ramesh Shanmugasundaram Signed-off-by: Oliver Hartkopp Reviewed-by: Ramesh Shanmugasundaram Signed-off-by: Marc Kleine-Budde Signed-off-by: Greg Kroah-Hartman

regulator: s2mps11: Fix invalid selector mask and voltages for buck9

2016-05-19T00:06:51Z

commit 3b672623079bb3e5685b8549e514f2dfaa564406 upstream. The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff instead of 0x1f) thus reading entire register as buck9's voltage. This effectively caused regulator core to interpret values as higher voltages than they were and then to set real voltage much lower than intended. The buck9 provides power to other regulators, including LDO13 and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower voltage caused SD card detection errors on Odroid XU3/XU4: mmc1: card never left busy state mmc1: error -110 whilst initialising SD card During driver probe the regulator core was checking whether initial voltage matches the constraints. With incorrect vsel_mask of 0xff and default value of 0x50, the core interpreted this as 5 V which is outside of constraints (3-3.775 V). Then the regulator core was adjusting the voltage to match the constraints. With incorrect vsel_mask this new voltage mapped to a vere low voltage in the driver. Signed-off-by: Krzysztof Kozlowski Reviewed-by: Javier Martinez Canillas Tested-by: Javier Martinez Canillas Signed-off-by: Mark Brown Signed-off-by: Greg Kroah-Hartman

vfs: add vfs_select_inode() helper

2016-05-19T00:06:48Z

commit 54d5ca871e72f2bb172ec9323497f01cd5091ec7 upstream. Signed-off-by: Miklos Szeredi Signed-off-by: Greg Kroah-Hartman

net: Implement net_dbg_ratelimited() for CONFIG_DYNAMIC_DEBUG case

2016-05-19T00:06:38Z

[ Upstream commit 2c94b53738549d81dc7464a32117d1f5112c64d3 ] Prior to commit d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when !DEBUG") the implementation of net_dbg_ratelimited() was buggy for both the DEBUG and CONFIG_DYNAMIC_DEBUG cases. The bug was that net_ratelimit() was being called and, despite returning true, nothing was being printed to the console. This resulted in messages like the following - "net_ratelimit: %d callbacks suppressed" with no other output nearby. After commit d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when !DEBUG") the bug is fixed for the DEBUG case. However, there's no output at all for CONFIG_DYNAMIC_DEBUG case. This patch restores debug output (if enabled) for the CONFIG_DYNAMIC_DEBUG case. Add a definition of net_dbg_ratelimited() for the CONFIG_DYNAMIC_DEBUG case. The implementation takes care to check that dynamic debugging is enabled before calling net_ratelimit(). Fixes: d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when !DEBUG") Signed-off-by: Tim Bingham Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

bpf: fix refcnt overflow

2016-05-19T00:06:37Z

[ Upstream commit 92117d8443bc5afacc8d5ba82e541946310f106e ] On a system with >32Gbyte of phyiscal memory and infinite RLIMIT_MEMLOCK, the malicious application may overflow 32-bit bpf program refcnt. It's also possible to overflow map refcnt on 1Tb system. Impose 32k hard limit which means that the same bpf program or map cannot be shared by more than 32k processes. Fixes: 1be7f75d1668 ("bpf: enable non-root eBPF programs") Reported-by: Jann Horn Signed-off-by: Alexei Starovoitov Acked-by: Daniel Borkmann Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net/mlx5e: Device's mtu field is u16 and not int

2016-05-19T00:06:36Z

[ Upstream commit 046339eaab26804f52f6604877f5674f70815b26 ] For set/query MTU port firmware commands the MTU field is 16 bits, here I changed all the "int mtu" parameters of the functions wrapping those firmware commands to be u16. Signed-off-by: Saeed Mahameed Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

Minimal fix-up of bad hashing behavior of hash_64()

2016-05-11T09:21:13Z

commit 689de1d6ca95b3b5bd8ee446863bf81a4883ea25 upstream. This is a fairly minimal fixup to the horribly bad behavior of hash_64() with certain input patterns. In particular, because the multiplicative value used for the 64-bit hash was intentionally bit-sparse (so that the multiply could be done with shifts and adds on architectures without hardware multipliers), some bits did not get spread out very much. In particular, certain fairly common bit ranges in the input (roughly bits 12-20: commonly with the most information in them when you hash things like byte offsets in files or memory that have block factors that mean that the low bits are often zero) would not necessarily show up much in the result. There's a bigger patch-series brewing to fix up things more completely, but this is the fairly minimal fix for the 64-bit hashing problem. It simply picks a much better constant multiplier, spreading the bits out a lot better. NOTE! For 32-bit architectures, the bad old hash_64() remains the same for now, since 64-bit multiplies are expensive. The bigger hashing cleanup will replace the 32-bit case with something better. The new constants were picked by George Spelvin who wrote that bigger cleanup series. I just picked out the constants and part of the comment from that series. Cc: George Spelvin Cc: Thomas Gleixner Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman