user/sven/linux.git/include/linux, branch v4.5.6

SIGNAL: Move generic copy_siginfo() to signal.h

2016-06-01T19:17:03Z

commit ca9eb49aa9562eaadf3cea071ec7018ad6800425 upstream. The generic copy_siginfo() is currently defined in asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which defines the generic struct siginfo. However this makes it awkward for an architecture to use it if it has to define its own struct siginfo (e.g. MIPS and potentially IA64), since it means that asm-generic/siginfo.h can only be included after defining the arch-specific siginfo, which may be problematic if the arch-specific definition needs definitions from uapi/asm-generic/siginfo.h. It is possible to work around this by first including uapi/asm-generic/siginfo.h to get the constants before defining the arch-specific siginfo, and include asm-generic/siginfo.h after. However uapi headers can't be included by other uapi headers, so that first include has to be in an ifdef __kernel__, with the non __kernel__ case including the non-UAPI header instead. Instead of that mess, move the generic copy_siginfo() definition into linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to include asm-generic/siginfo.h and define the arch-specific siginfo, and for the generic copy_siginfo() to see that arch-specific definition. Signed-off-by: James Hogan Cc: Arnd Bergmann Cc: Ralf Baechle Cc: Petr Malat Cc: Tony Luck Cc: Fenghua Yu Cc: Christopher Ferris Cc: linux-arch@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-ia64@vger.kernel.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/12478/ Signed-off-by: Ralf Baechle Signed-off-by: Greg Kroah-Hartman

Fix OpenSSH pty regression on close

2016-06-01T19:17:02Z

commit 0f40fbbcc34e093255a2b2d70b6b0fb48c3f39aa upstream. OpenSSH expects the (non-blocking) read() of pty master to return EAGAIN only if it has received all of the slave-side output after it has received SIGCHLD. This used to work on pre-3.12 kernels. This fix effectively forces non-blocking read() and poll() to block for parallel i/o to complete for all ttys. It also unwinds these changes: 1) f8747d4a466ab2cafe56112c51b3379f9fdb7a12 tty: Fix pty master read() after slave closes 2) 52bce7f8d4fc633c9a9d0646eef58ba6ae9a3b73 pty, n_tty: Simplify input processing on final close 3) 1a48632ffed61352a7810ce089dc5a8bcd505a60 pty: Fix input race when closing Inspired by analysis and patch from Marc Aurele La France Reported-by: Volth Reported-by: Marc Aurele La France BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=52 BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=2492 Signed-off-by: Brian Bloniarz Reviewed-by: Peter Hurley Signed-off-by: Greg Kroah-Hartman

USB: leave LPM alone if possible when binding/unbinding interface drivers

2016-06-01T19:17:01Z

commit 6fb650d43da3e7054984dc548eaa88765a94d49f upstream. When a USB driver is bound to an interface (either through probing or by claiming it) or is unbound from an interface, the USB core always disables Link Power Management during the transition and then re-enables it afterward. The reason is because the driver might want to prevent hub-initiated link power transitions, in which case the HCD would have to recalculate the various LPM parameters. This recalculation takes place when LPM is re-enabled and the new parameters are sent to the device and its parent hub. However, if the driver does not want to prevent hub-initiated link power transitions then none of this work is necessary. The parameters don't need to be recalculated, and LPM doesn't need to be disabled and re-enabled. It turns out that disabling and enabling LPM can be time-consuming, enough so that it interferes with user programs that want to claim and release interfaces rapidly via usbfs. Since the usbfs kernel driver doesn't set the disable_hub_initiated_lpm flag, we can speed things up and get the user programs to work by leaving LPM alone whenever the flag isn't set. And while we're improving the way disable_hub_initiated_lpm gets used, let's also fix its kerneldoc. Signed-off-by: Alan Stern Tested-by: Matthew Giassa CC: Mathias Nyman Signed-off-by: Greg Kroah-Hartman

can: fix handling of unmodifiable configuration options

2016-06-01T19:16:58Z

commit bb208f144cf3f59d8f89a09a80efd04389718907 upstream. As described in 'can: m_can: tag current CAN FD controllers as non-ISO' (6cfda7fbebe) it is possible to define fixed configuration options by setting the according bit in 'ctrlmode' and clear it in 'ctrlmode_supported'. This leads to the incovenience that the fixed configuration bits can not be passed by netlink even when they have the correct values (e.g. non-ISO, FD). This patch fixes that issue and not only allows fixed set bit values to be set again but now requires(!) to provide these fixed values at configuration time. A valid CAN FD configuration consists of a nominal/arbitration bittiming, a data bittiming and a control mode with CAN_CTRLMODE_FD set - which is now enforced by a new can_validate() function. This fix additionally removed the inconsistency that was prohibiting the support of 'CANFD-only' controller drivers, like the RCar CAN FD. For this reason a new helper can_set_static_ctrlmode() has been introduced to provide a proper interface to handle static enabled CAN controller options. Reported-by: Ramesh Shanmugasundaram Signed-off-by: Oliver Hartkopp Reviewed-by: Ramesh Shanmugasundaram Signed-off-by: Marc Kleine-Budde Signed-off-by: Greg Kroah-Hartman

regulator: s2mps11: Fix invalid selector mask and voltages for buck9

2016-05-19T01:35:12Z

commit 3b672623079bb3e5685b8549e514f2dfaa564406 upstream. The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff instead of 0x1f) thus reading entire register as buck9's voltage. This effectively caused regulator core to interpret values as higher voltages than they were and then to set real voltage much lower than intended. The buck9 provides power to other regulators, including LDO13 and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower voltage caused SD card detection errors on Odroid XU3/XU4: mmc1: card never left busy state mmc1: error -110 whilst initialising SD card During driver probe the regulator core was checking whether initial voltage matches the constraints. With incorrect vsel_mask of 0xff and default value of 0x50, the core interpreted this as 5 V which is outside of constraints (3-3.775 V). Then the regulator core was adjusting the voltage to match the constraints. With incorrect vsel_mask this new voltage mapped to a vere low voltage in the driver. Signed-off-by: Krzysztof Kozlowski Reviewed-by: Javier Martinez Canillas Tested-by: Javier Martinez Canillas Signed-off-by: Mark Brown Signed-off-by: Greg Kroah-Hartman

vfs: add vfs_select_inode() helper

2016-05-19T01:35:12Z

commit 54d5ca871e72f2bb172ec9323497f01cd5091ec7 upstream. Signed-off-by: Miklos Szeredi Signed-off-by: Greg Kroah-Hartman

mm: thp: calculate the mapcount correctly for THP pages during WP faults

2016-05-19T01:35:09Z

commit 6d0a07edd17cfc12fdc1f36de8072fa17cc3666f upstream. This will provide fully accuracy to the mapcount calculation in the write protect faults, so page pinning will not get broken by false positive copy-on-writes. total_mapcount() isn't the right calculation needed in reuse_swap_page(), so this introduces a page_trans_huge_mapcount() that is effectively the full accurate return value for page_mapcount() if dealing with Transparent Hugepages, however we only use the page_trans_huge_mapcount() during COW faults where it strictly needed, due to its higher runtime cost. This also provide at practical zero cost the total_mapcount information which is needed to know if we can still relocate the page anon_vma to the local vma. If page_trans_huge_mapcount() returns 1 we can reuse the page no matter if it's a pte or a pmd_trans_huge triggering the fault, but we can only relocate the page anon_vma to the local vma->anon_vma if we're sure it's only this "vma" mapping the whole THP physical range. Kirill A. Shutemov discovered the problem with moving the page anon_vma to the local vma->anon_vma in a previous version of this patch and another problem in the way page_move_anon_rmap() was called. Andrew Morton discovered that CONFIG_SWAP=n wouldn't build in a previous version, because reuse_swap_page must be a macro to call page_trans_huge_mapcount from swap.h, so this uses a macro again instead of an inline function. With this change at least it's a less dangerous usage than it was before, because "page" is used only once now, while with the previous code reuse_swap_page(page++) would have called page_mapcount on page+1 and it would have increased page twice instead of just once. Dean Luick noticed an uninitialized variable that could result in a rmap inefficiency for the non-THP case in a previous version. Mike Marciniszyn said: : Our RDMA tests are seeing an issue with memory locking that bisects to : commit 61f5d698cc97 ("mm: re-enable THP") : : The test program registers two rather large MRs (512M) and RDMA : writes data to a passive peer using the first and RDMA reads it back : into the second MR and compares that data. The sizes are chosen randomly : between 0 and 1024 bytes. : : The test will get through a few (<= 4 iterations) and then gets a : compare error. : : Tracing indicates the kernel logical addresses associated with the individual : pages at registration ARE correct , the data in the "RDMA read response only" : packets ARE correct. : : The "corruption" occurs when the packet crosse two pages that are not physically : contiguous. The second page reads back as zero in the program. : : It looks like the user VA at the point of the compare error no longer points to : the same physical address as was registered. : : This patch totally resolves the issue! Link: http://lkml.kernel.org/r/1462547040-1737-2-git-send-email-aarcange@redhat.com Signed-off-by: Andrea Arcangeli Reviewed-by: "Kirill A. Shutemov" Reviewed-by: Dean Luick Tested-by: Alex Williamson Tested-by: Mike Marciniszyn Tested-by: Josh Collier Cc: Marc Haber Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman

net: Implement net_dbg_ratelimited() for CONFIG_DYNAMIC_DEBUG case

2016-05-19T01:35:04Z

[ Upstream commit 2c94b53738549d81dc7464a32117d1f5112c64d3 ] Prior to commit d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when !DEBUG") the implementation of net_dbg_ratelimited() was buggy for both the DEBUG and CONFIG_DYNAMIC_DEBUG cases. The bug was that net_ratelimit() was being called and, despite returning true, nothing was being printed to the console. This resulted in messages like the following - "net_ratelimit: %d callbacks suppressed" with no other output nearby. After commit d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when !DEBUG") the bug is fixed for the DEBUG case. However, there's no output at all for CONFIG_DYNAMIC_DEBUG case. This patch restores debug output (if enabled) for the CONFIG_DYNAMIC_DEBUG case. Add a definition of net_dbg_ratelimited() for the CONFIG_DYNAMIC_DEBUG case. The implementation takes care to check that dynamic debugging is enabled before calling net_ratelimit(). Fixes: d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when !DEBUG") Signed-off-by: Tim Bingham Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

bpf: fix refcnt overflow

2016-05-19T01:35:04Z

[ Upstream commit 92117d8443bc5afacc8d5ba82e541946310f106e ] On a system with >32Gbyte of phyiscal memory and infinite RLIMIT_MEMLOCK, the malicious application may overflow 32-bit bpf program refcnt. It's also possible to overflow map refcnt on 1Tb system. Impose 32k hard limit which means that the same bpf program or map cannot be shared by more than 32k processes. Fixes: 1be7f75d1668 ("bpf: enable non-root eBPF programs") Reported-by: Jann Horn Signed-off-by: Alexei Starovoitov Acked-by: Daniel Borkmann Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net/mlx5e: Use vport MTU rather than physical port MTU

2016-05-19T01:35:03Z

[ Upstream commit cd255efff9baadd654d6160e52d17ae7c568c9d3 ] Set and report vport MTU rather than physical MTU, Driver will set both vport and physical port mtu and will rely on the query of vport mtu. SRIOV VFs have to report their MTU to their vport manager (PF), and this will allow them to work with any MTU they need without failing the request. Also for some cases where the PF is not a port owner, PF can work with MTU less than the physical port mtu if set physical port mtu didn't take effect. Signed-off-by: Saeed Mahameed Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman