user/sven/linux.git/include/rdma, branch ipvs/checkpatch-cleanup

Merge branch 'misc' into for-next

2010-03-02T07:52:31Z

Conflicts: drivers/infiniband/core/uverbs_main.c

Merge branch 'cma' into for-next

2010-03-02T07:51:54Z

IB/core: Fix and clean up ib_ud_header_init()

2010-02-24T22:54:10Z

ib_ud_header_init() first clears header and then fills up the various fields. Later on, it tests header->immediate_present, which it has already cleared, so the condition is always false. Fix this by adding an immediate_present parameter and setting header->immediate_present as is done with grh_present. Also remove unused calculation of header_len. Signed-off-by: Eli Cohen Signed-off-by: Roland Dreier

IB/core: Pack struct ib_device a little tighter

2010-02-24T18:23:49Z

A small change to reduce the size of ib_device to 1112 bytes (from 1128). Signed-off-by: Alex Chiang Signed-off-by: Roland Dreier

RDMA/cm: Remove unused definition of RDMA_PS_SCTP

2010-02-11T23:40:25Z

The defined SCTP number is incorrect (0x83, rather than 0x84), and since it is not used anywhere, simply remove the definition. Signed-off-by: Sean Hefty Signed-off-by: Roland Dreier

Merge branches 'amso1100', 'cma', 'cxgb3', 'ehca', 'ipath', 'ipoib', 'iser', 'misc', 'mlx4' and 'nes' into for-next

2009-12-16T07:39:25Z

IB: Clarify the documentation of ib_post_send()

2009-12-09T22:20:04Z

Clarify the behavior of ib_post_send() when a list of work requests is passed in and an immediate error is returned. Signed-off-by: Bart Van Assche Signed-off-by: Roland Dreier

RDMA/cm: fix loopback address support

2009-11-19T21:26:06Z

The RDMA CM is intended to support the use of a loopback address when establishing a connection; however, the behavior of the CM when loopback addresses are used is confusing and does not always work, depending on whether loopback was specified by the server, the client, or both. The defined behavior of rdma_bind_addr is to associate an RDMA device with an rdma_cm_id, as long as the user specified a non- zero address. (ie they weren't just trying to reserve a port) Currently, if the loopback address is passed to rdam_bind_addr, no device is associated with the rdma_cm_id. Fix this. If a loopback address is specified by the client as the destination address for a connection, it will fail to establish a connection. This is true even if the server is listing across all addresses or on the loopback address itself. The issue is that the server tries to translate the IP address carried in the REQ message to a local net_device address, which fails. The translation is not needed in this case, since the REQ carries the actual HW address that should be used. Finally, cleanup loopback support to be more transport neutral. Replace separate calls to get/set the sgid and dgid from the device address to a single call that behaves correctly depending on the format of the device address. And support both IPv4 and IPv6 address formats. Signed-off-by: Sean Hefty [ Fixed RDS build by s/ib_addr_get/rdma_addr_get/ - Roland ] Signed-off-by: Roland Dreier

IB/addr: Store net_device type instead of translating to RDMA transport

2009-11-19T20:57:18Z

The struct rdma_dev_addr stores net_device address information: the source device address, destination hardware address, and broadcast address. For consistency, store the net_device type rather than converting it to the rdma_node_type. The type indicates the format of the various hardware addresses, which is what we're concerned with, and not the RDMA node type that the address may map to. Signed-off-by: Sean Hefty Signed-off-by: Roland Dreier

RDMA/cma: Replace net_device pointer with index

2009-11-19T20:55:22Z

Provide the device interface when resolving route information to ensure that the correct outbound device is used. This will also simplify processing of sin6_scope_id for IPv6 support. Based on work from: David Wilder Jason Gunthorpe Signed-off-by: Sean Hefty Signed-off-by: Roland Dreier