user/sven/linux.git/include/scsi, branch v3.10.106

scsi: fix our current target reap infrastructure

2014-05-31T04:52:11Z

commit e63ed0d7a98014fdfc2cfeb3f6dada313dcabb59 upstream. This patch eliminates the reap_ref and replaces it with a proper kref. On last put of this kref, the target is removed from visibility in sysfs. The final call to scsi_target_reap() for the device is done from __scsi_remove_device() and only if the device was made visible. This ensures that the target disappears as soon as the last device is gone rather than waiting until final release of the device (which is often too long). Reviewed-by: Alan Stern Tested-by: Sarah Sharp Signed-off-by: James Bottomley Signed-off-by: Greg Kroah-Hartman

ore: Fix wrong math in allocation of per device BIO

2014-02-13T21:48:00Z

commit aad560b7f63b495f48a7232fd086c5913a676e6f upstream. At IO preparation we calculate the max pages at each device and allocate a BIO per device of that size. The calculation was wrong on some unaligned corner cases offset/length combination and would make prepare return with -ENOMEM. This would be bad for pnfs-objects that would in that case IO through MDS. And fatal for exofs were it would fail writes with EIO. Fix it by doing the proper math, that will work in all cases. (I ran a test with all possible offset/length combinations this time round). Also when reading we do not need to allocate for the parity units since we jump over them. Also lower the max_io_length to take into account the parity pages so not to allocate BIOs bigger than PAGE_SIZE Signed-off-by: Boaz Harrosh Signed-off-by: Greg Kroah-Hartman

SCSI: Disable WRITE SAME for RAID and virtual host adapter drivers

2013-12-12T06:36:28Z

commit 54b2b50c20a61b51199bedb6e5d2f8ec2568fb43 upstream. Some host adapters do not pass commands through to the target disk directly. Instead they provide an emulated target which may or may not accurately report its capabilities. In some cases the physical device characteristics are reported even when the host adapter is processing commands on the device's behalf. This can lead to adapter firmware hangs or excessive I/O errors. This patch disables WRITE SAME for devices connected to host adapters that provide an emulated target. Driver writers can disable WRITE SAME by setting the no_write_same flag in the host adapter template. [jejb: fix up rejections due to eh_deadline patch] Signed-off-by: Martin K. Petersen Signed-off-by: James Bottomley Signed-off-by: Greg Kroah-Hartman

Merge branch 'postmerge' into for-linus

2013-05-10T14:54:01Z

Signed-off-by: James Bottomley

Merge branch 'misc' into for-linus

2013-05-10T14:53:40Z

Signed-off-by: James Bottomley

[SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used

2013-05-10T14:47:53Z

This fixes a bug where the iscsi class/driver did not do a put_device when a sess/conn device was found. This also simplifies the interface by not having to pass in some arguments that were duplicated and did not need to be exported. Reported-by: Zhao Hongjiang Signed-off-by: Mike Christie Acked-by: Vikas Chaudhary Signed-off-by: James Bottomley

[SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type

2013-05-10T14:47:52Z

These enums have been separate since the dawn of SAS, mainly because the latter is a procotol only enum and the former includes additional state for libsas. The dichotomy causes endless confusion about which one you should use where and leads to pointless warnings like this: drivers/scsi/mvsas/mv_sas.c: In function 'mvs_update_phyinfo': drivers/scsi/mvsas/mv_sas.c:1162:34: warning: comparison between 'enum sas_device_type' and 'enum sas_dev_type' [-Wenum-compare] Fix by eliminating one of them. The one kept is effectively the sas.h one, but call it sas_device_type and make sure the enums are all properly namespaced with the SAS_ prefix. Signed-off-by: James Bottomley

[SCSI] sd: use REQ_PM in sd's runtime suspend operation

2013-05-06T19:48:17Z

With the introduction of REQ_PM, modify sd's runtime suspend operation functions to use that flag so that the operations to put the device into runtime suspended state(i.e. sync cache and stop device) will not affect its runtime PM status. Signed-off-by: Lin Ming Signed-off-by: Aaron Lu Acked-by: Alan Stern Signed-off-by: James Bottomley

[SCSI] libosd: remover duplicate __bitwise annotation

2013-05-02T19:15:10Z

__be32 is already a __bitwise type so we don't need the second __bitwise here. It causes a Sparse error: include/scsi/osd_protocol.h:110:26: error: invalid modifier Signed-off-by: Dan Carpenter Acked-by: Benny Halevy Signed-off-by: James Bottomley

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs

2013-05-02T00:51:54Z

Pull VFS updates from Al Viro, Misc cleanups all over the place, mainly wrt /proc interfaces (switch create_proc_entry to proc_create(), get rid of the deprecated create_proc_read_entry() in favor of using proc_create_data() and seq_file etc). 7kloc removed. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits) don't bother with deferred freeing of fdtables proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h proc: Make the PROC_I() and PDE() macros internal to procfs proc: Supply a function to remove a proc entry by PDE take cgroup_open() and cpuset_open() to fs/proc/base.c ppc: Clean up scanlog ppc: Clean up rtas_flash driver somewhat hostap: proc: Use remove_proc_subtree() drm: proc: Use remove_proc_subtree() drm: proc: Use minor->index to label things, not PDE->name drm: Constify drm_proc_list[] zoran: Don't print proc_dir_entry data in debug reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show() proc: Supply an accessor for getting the data from a PDE's parent airo: Use remove_proc_subtree() rtl8192u: Don't need to save device proc dir PDE rtl8187se: Use a dir under /proc/net/r8180/ proc: Add proc_mkdir_data() proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h} proc: Move PDE_NET() to fs/proc/proc_net.c ...