user/sven/linux.git/include/uapi/linux/ethtool.h, branch v5.8.14

ethtool: provide UAPI for PHY master/slave configuration.

2020-05-07T00:45:45Z

This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of auto-negotiation support, we needed to be able to configure the MASTER-SLAVE role of the port manually or from an application in user space. The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to force MASTER or SLAVE role. See IEEE 802.3-2018: 22.2.4.3.7 MASTER-SLAVE control register (Register 9) 22.2.4.3.8 MASTER-SLAVE status register (Register 10) 40.5.2 MASTER-SLAVE configuration resolution 45.2.1.185.1 MASTER-SLAVE config value (1.2100.14) 45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32) The MASTER-SLAVE role affects the clock configuration: ------------------------------------------------------------------------------- When the PHY is configured as MASTER, the PMA Transmit function shall source TX_TCLK from a local clock source. When configured as SLAVE, the PMA Transmit function shall source TX_TCLK from the clock recovered from data stream provided by MASTER. iMX6Q KSZ9031 XXX ------\ /-----------\ /------------\ | | | | | MAC |<----RGMII----->| PHY Slave |<------>| PHY Master | |<--- 125 MHz ---+-<------/ | | \ | ------/ \-----------/ \------------/ ^ \-TX_TCLK ------------------------------------------------------------------------------- Since some clock or link related issues are only reproducible in a specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial to provide generic (not 100BASE-T1 specific) interface to the user space for configuration flexibility and trouble shooting. Signed-off-by: Oleksij Rempel Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

ethtool: add timestamping related string sets

2020-03-30T05:32:36Z

Add three string sets related to timestamping information: ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags ETH_SS_TS_TX_TYPES: timestamping Tx types ETH_SS_TS_RX_FILTERS: timestamping Rx filters These will be used for TIMESTAMP_GET request. v2: avoid compiler warning ("enumeration value not handled in switch") in net_hwtstamp_validate() v3: omit dash in Tx type names ("one-step-*" -> "onestep-*"), suggested by Richard Cochran Signed-off-by: Michal Kubecek Acked-by: Richard Cochran Signed-off-by: David S. Miller

ethtool: Add support for low latency RS FEC

2020-02-19T03:17:31Z

Add support for low latency Reed Solomon FEC as LLRS. The LL-FEC is defined by the 25G/50G ethernet consortium, in the document titled "Low Latency Reed Solomon Forward Error Correction" Signed-off-by: Aya Levin Reviewed-by: Eran Ben Elisha CC: Andrew Lunn Signed-off-by: Saeed Mahameed Reviewed-by: Andrew Lunn

ethtool: provide WoL settings with WOL_GET request

2020-01-27T10:31:36Z

Implement WOL_GET request to get wake-on-lan settings for a device, traditionally available via ETHTOOL_GWOL ioctl request. As part of the implementation, provide symbolic names for wake-on-line modes as ETH_SS_WOL_MODES string set. Signed-off-by: Michal Kubecek Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

ethtool: provide message mask with DEBUG_GET request

2020-01-27T10:31:35Z

Implement DEBUG_GET request to get debugging settings for a device. At the moment, only message mask corresponding to message level as reported by ETHTOOL_GMSGLVL ioctl request is provided. (It is called message level in ioctl interface but almost all drivers interpret it as a bit mask.) As part of the implementation, provide symbolic names for message mask bits as ETH_SS_MSG_CLASSES string set. Signed-off-by: Michal Kubecek Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

ethtool: provide string sets with STRSET_GET request

2019-12-28T00:40:01Z

Requests a contents of one or more string sets, i.e. indexed arrays of strings; this information is provided by ETHTOOL_GSSET_INFO and ETHTOOL_GSTRINGS commands of ioctl interface. Unlike ioctl interface, all information can be retrieved with one request and mulitple string sets can be requested at once. There are three types of requests: - no NLM_F_DUMP, no device: get "global" stringsets - no NLM_F_DUMP, with device: get string sets related to the device - NLM_F_DUMP, no device: get device related string sets for all devices Client can request either all string sets of given type (global or device related) or only specific sets. With ETHTOOL_A_STRSET_COUNTS flag set, only set sizes (numbers of strings) are returned. Signed-off-by: Michal Kubecek Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

ethtool: provide link mode names as a string set

2019-12-13T01:07:05Z

Unlike e.g. netdev features, the ethtool ioctl interface requires link mode table to be in sync between kernel and userspace for userspace to be able to display and set all link modes supported by kernel. The way arbitrary length bitsets are implemented in netlink interface, this will be no longer needed. To allow userspace to access all link modes running kernel supports, add table of ethernet link mode names and make it available as a string set to userspace GET_STRSET requests. Add build time check to make sure names are defined for all modes declared in enum ethtool_link_mode_bit_indices. Once the string set is available, make it also accessible via ioctl. Signed-off-by: Michal Kubecek Reviewed-by: Andrew Lunn Reviewed-by: Jiri Pirko Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

ethtool: Add support for 400Gbps (50Gbps per lane) link modes

2019-10-15T22:02:30Z

Add support for 400Gbps speed, link modes of 50Gbps per lane Signed-off-by: Jiri Pirko Signed-off-by: Ido Schimmel Signed-off-by: David S. Miller

ethtool: implement Energy Detect Powerdown support via phy-tunable

2019-09-16T20:02:45Z

The `phy_tunable_id` has been named `ETHTOOL_PHY_EDPD` since it looks like this feature is common across other PHYs (like EEE), and defining `ETHTOOL_PHY_ENERGY_DETECT_POWER_DOWN` seems too long. The way EDPD works, is that the RX block is put to a lower power mode, except for link-pulse detection circuits. The TX block is also put to low power mode, but the PHY wakes-up periodically to send link pulses, to avoid lock-ups in case the other side is also in EDPD mode. Currently, there are 2 PHY drivers that look like they could use this new PHY tunable feature: the `adin` && `micrel` PHYs. The ADIN's datasheet mentions that TX pulses are at intervals of 1 second default each, and they can be disabled. For the Micrel KSZ9031 PHY, the datasheet does not mention whether they can be disabled, but mentions that they can modified. The way this change is structured, is similar to the PHY tunable downshift control: * a `ETHTOOL_PHY_EDPD_DFLT_TX_MSECS` value is exposed to cover a default TX interval; some PHYs could specify a certain value that makes sense * `ETHTOOL_PHY_EDPD_NO_TX` would disable TX when EDPD is enabled * `ETHTOOL_PHY_EDPD_DISABLE` will disable EDPD As noted by the `ETHTOOL_PHY_EDPD_DFLT_TX_MSECS` the interval unit is 1 millisecond, which should cover a reasonable range of intervals: - from 1 millisecond, which does not sound like much of a power-saver - to ~65 seconds which is quite a lot to wait for a link to come up when plugging a cable Reviewed-by: Andrew Lunn Reviewed-by: Florian Fainelli Signed-off-by: Alexandru Ardelean Signed-off-by: David S. Miller

net: phy: Add support for 100BaseT1 and 1000BaseT1

2019-05-23T00:46:28Z

Add link modes for 100Mbps and 1Gbps over a single pair. Signed-off-by: Andrew Lunn Signed-off-by: David S. Miller