user/sven/linux.git/kernel/time, branch v2.6.26.8

clockevents: remove WARN_ON which was used to gather information

2008-10-09T03:23:05Z

commit 61c22c34c6f80a8e89cff5ff717627c54cc14fd4 upstream The issue of the endless reprogramming loop due to a too small min_delta_ns was fixed with the previous updates of the clock events code, but we had no information about the spread of this problem. I added a WARN_ON to get automated information via kerneloops.org and to get some direct reports, which allowed me to analyse the affected machines. The WARN_ON has served its purpose and would be annoying for a release kernel. Remove it and just keep the information about the increase of the min_delta_ns value. Signed-off-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

ntp: fix calculation of the next jiffie to trigger RTC sync

2008-10-09T03:23:05Z

commit 4ff4b9e19a80b73959ebeb28d1df40176686f0a8 upstream We have a bug in the calculation of the next jiffie to trigger the RTC synchronisation. The aim here is to run sync_cmos_clock() as close as possible to the middle of a second. Which means we want this function to be called less than or equal to half a jiffie away from when now.tv_nsec equals 5e8 (500000000). If this is not the case for a given call to the function, for this purpose instead of updating the RTC we calculate the offset in nanoseconds to the next point in time where now.tv_nsec will be equal 5e8. The calculated offset is then converted to jiffies as these are the unit used by the timer. Hovewer timespec_to_jiffies() used here uses a ceil()-type rounding mode, where the resulting value is rounded up. As a result the range of now.tv_nsec when the timer will trigger is from 5e8 to 5e8 + TICK_NSEC rather than the desired 5e8 - TICK_NSEC / 2 to 5e8 + TICK_NSEC / 2. As a result if for example sync_cmos_clock() happens to be called at the time when now.tv_nsec is between 5e8 + TICK_NSEC / 2 and 5e8 to 5e8 + TICK_NSEC, it will simply be rescheduled HZ jiffies later, falling in the same range of now.tv_nsec again. Similarly for cases offsetted by an integer multiple of TICK_NSEC. This change addresses the problem by subtracting TICK_NSEC / 2 from the nanosecond offset to the next point in time where now.tv_nsec will be equal 5e8, effectively shifting the following rounding in timespec_to_jiffies() so that it produces a rounded-to-nearest result. Signed-off-by: Maciej W. Rozycki Signed-off-by: Andrew Morton Signed-off-by: Ingo Molnar Signed-off-by: Greg Kroah-Hartman

clockevents: broadcast fixup possible waiters

2008-10-09T03:23:05Z

commit 7300711e8c6824fcfbd42a126980ff50439d8dd0 upstream Until the C1E patches arrived there where no users of periodic broadcast before switching to oneshot mode. Now we need to trigger a possible waiter for a periodic broadcast when switching to oneshot mode. Otherwise we can starve them for ever. Signed-off-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

clockevents: prevent endless loop lockup

2008-10-09T03:23:04Z

commit 1fb9b7d29d8e85ba3196eaa7ab871bf76fc98d36 upstream The C1E/HPET bug reports on AMDX2/RS690 systems where tracked down to a too small value of the HPET minumum delta for programming an event. The clockevents code needs to enforce an interrupt event on the clock event device in some cases. The enforcement code was stupid and naive, as it just added the minimum delta to the current time and tried to reprogram the device. When the minimum delta is too small, then this loops forever. Add a sanity check. Allow reprogramming to fail 3 times, then print a warning and double the minimum delta value to make sure, that this does not happen again. Use the same function for both tick-oneshot and tick-broadcast code. Signed-off-by: Thomas Gleixner Signed-off-by: Ingo Molnar Signed-off-by: Greg Kroah-Hartman

clockevents: prevent multiple init/shutdown

2008-10-09T03:23:04Z

commit 9c17bcda991000351cb2373f78be7e4b1c44caa3 upstream While chasing the C1E/HPET bugreports I went through the clock events code inch by inch and found that the broadcast device can be initialized and shutdown multiple times. Multiple shutdowns are not critical, but useless waste of time. Multiple initializations are simply broken. Another CPU might have the device in use already after the first initialization and the second init could just render it unusable again. Signed-off-by: Thomas Gleixner Signed-off-by: Ingo Molnar Signed-off-by: Greg Kroah-Hartman

clockevents: enforce reprogram in oneshot setup

2008-10-09T03:23:03Z

commit 7205656ab48da29a95d7f55e43a81db755d3cb3a upstream In tick_oneshot_setup we program the device to the given next_event, but we do not check the return value. We need to make sure that the device is programmed enforced so the interrupt handler engine starts working. Split out the reprogramming function from tick_program_event() and call it with the device, which was handed in to tick_setup_oneshot(). Set the force argument, so the devices is firing an interrupt. Signed-off-by: Thomas Gleixner Signed-off-by: Ingo Molnar Signed-off-by: Greg Kroah-Hartman

clockevents: prevent endless loop in periodic broadcast handler

2008-10-09T03:23:03Z

commit d4496b39559c6d43f83e4c08b899984f8b8089b5 upstream The reprogramming of the periodic broadcast handler was broken, when the first programming returned -ETIME. The clockevents code stores the new expiry value in the clock events device next_event field only when the programming time has not been elapsed yet. The loop in question calculates the new expiry value from the next_event value and therefor never increases. Signed-off-by: Thomas Gleixner Signed-off-by: Ingo Molnar Signed-off-by: Greg Kroah-Hartman

clockevents: prevent clockevent event_handler ending up handler_noop

2008-10-09T03:23:03Z

commit 7c1e76897492d92b6a1c2d6892494d39ded9680c upstream There is a ordering related problem with clockevents code, due to which clockevents_register_device() called after tickless/highres switch will not work. The new clockevent ends up with clockevents_handle_noop as event handler, resulting in no timer activity. The problematic path seems to be * old device already has hrtimer_interrupt as the event_handler * new clockevent device registers with a higher rating * tick_check_new_device() is called * clockevents_exchange_device() gets called * old->event_handler is set to clockevents_handle_noop * tick_setup_device() is called for the new device * which sets new->event_handler using the old->event_handler which is noop. Change the ordering so that new device inherits the proper handler. This does not have any issue in normal case as most likely all the clockevent devices are setup before the highres switch. But, can potentially be affecting some corner case where HPET force detect happens after the highres switch. This was a problem with HPET in MSI mode code that we have been experimenting with. Signed-off-by: Venkatesh Pallipadi Signed-off-by: Shaohua Li Signed-off-by: Thomas Gleixner Signed-off-by: Ingo Molnar Signed-off-by: Greg Kroah-Hartman

clocksource: allow read access to available/current_clocksource

2008-05-03T16:11:48Z

There is no harm, when users can read the info and we ask often enough during debugging for this kind of information. Signed-off-by: Heiko Carstens Cc: Andrew Morton Cc: John Stultz Signed-off-by: Thomas Gleixner

clocksource: Fix permissions for available_clocksource

2008-05-03T16:11:48Z

File permissions for /sys/devices/system/clocksource/clocksource0/available_clocksource are 600 which allows write access. But this is in fact a read only file. So change permissions to 400. Signed-off-by: Heiko Carstens Cc: John Stultz Cc: Andrew Morton Signed-off-by: Thomas Gleixner