1 files changed, 280 insertions, 0 deletions
diff --git a/drivers/tty/serial/8250/8250_keba.c b/drivers/tty/serial/8250/8250_keba.c
new file mode 100644
index 000000000000..c05b89551b12
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_keba.c
@@ -0,0 +1,280 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2025 KEBA Industrial Automation GmbH
+ *
+ * Driver for KEBA UART FPGA IP core
+ */
+
+#include <linux/auxiliary_bus.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/misc/keba.h>
+#include <linux/module.h>
+
+#include "8250.h"
+
+#define KUART "kuart"
+
+/* flags */
+#define KUART_RS485		BIT(0)
+#define KUART_USE_CAPABILITY	BIT(1)
+
+/* registers */
+#define KUART_VERSION		0x0000
+#define KUART_REVISION		0x0001
+#define KUART_CAPABILITY	0x0002
+#define KUART_CONTROL		0x0004
+#define KUART_BASE		0x000C
+#define KUART_REGSHIFT		2
+#define KUART_CLK		1843200
+
+/* mode flags */
+enum kuart_mode {
+	KUART_MODE_NONE = 0,
+	KUART_MODE_RS485,
+	KUART_MODE_RS422,
+	KUART_MODE_RS232
+};
+
+/* capability flags */
+#define KUART_CAPABILITY_NONE	BIT(KUART_MODE_NONE)
+#define KUART_CAPABILITY_RS485	BIT(KUART_MODE_RS485)
+#define KUART_CAPABILITY_RS422	BIT(KUART_MODE_RS422)
+#define KUART_CAPABILITY_RS232	BIT(KUART_MODE_RS232)
+#define KUART_CAPABILITY_MASK	GENMASK(3, 0)
+
+/* Additional Control Register DTR line configuration */
+#define UART_ACR_DTRLC_MASK		0x18
+#define UART_ACR_DTRLC_COMPAT		0x00
+#define UART_ACR_DTRLC_ENABLE_LOW	0x10
+
+struct kuart {
+	struct keba_uart_auxdev *auxdev;
+	void __iomem *base;
+	unsigned int line;
+
+	unsigned int flags;
+	u8 capability;
+	enum kuart_mode mode;
+};
+
+static void kuart_set_phy_mode(struct kuart *kuart, enum kuart_mode mode)
+{
+	iowrite8(mode, kuart->base + KUART_CONTROL);
+}
+
+static void kuart_enhanced_mode(struct uart_8250_port *up, bool enable)
+{
+	u8 lcr, efr;
+
+	/* backup LCR register */
+	lcr = serial_in(up, UART_LCR);
+
+	/* enable 650 compatible register set (EFR, ...) */
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
+
+	/* enable/disable enhanced mode with indexed control registers */
+	efr = serial_in(up, UART_EFR);
+	if (enable)
+		efr |= UART_EFR_ECB;
+	else
+		efr &= ~UART_EFR_ECB;
+	serial_out(up, UART_EFR, efr);
+
+	/* disable 650 compatible register set, restore LCR */
+	serial_out(up, UART_LCR, lcr);
+}
+
+static void kuart_dtr_line_config(struct uart_8250_port *up, u8 dtrlc)
+{
+	u8 acr;
+
+	/* set index register to 0 to access ACR register */
+	serial_out(up, UART_SCR, UART_ACR);
+
+	/* set value register to 0x10 writing DTR mode (1,0) */
+	acr = serial_in(up, UART_LSR);
+	acr &= ~UART_ACR_DTRLC_MASK;
+	acr |= dtrlc;
+	serial_out(up, UART_LSR, acr);
+}
+
+static int kuart_rs485_config(struct uart_port *port, struct ktermios *termios,
+			      struct serial_rs485 *rs485)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	struct kuart *kuart = port->private_data;
+	enum kuart_mode mode;
+	u8 dtrlc;
+
+	if (rs485->flags & SER_RS485_ENABLED) {
+		if (rs485->flags & SER_RS485_MODE_RS422)
+			mode = KUART_MODE_RS422;
+		else
+			mode = KUART_MODE_RS485;
+	} else {
+		mode = KUART_MODE_RS232;
+	}
+
+	if (mode == kuart->mode)
+		return 0;
+
+	if (kuart->flags & KUART_USE_CAPABILITY) {
+		/* deactivate physical interface, break before make */
+		kuart_set_phy_mode(kuart, KUART_MODE_NONE);
+	}
+
+	if (mode == KUART_MODE_RS485) {
+		/*
+		 * Set DTR line configuration of 95x UART to DTR mode (1,0).
+		 * In this mode the DTR pin drives the active-low enable pin of
+		 * an external RS485 buffer. The DTR pin will be forced low
+		 * whenever the transmitter is not empty, otherwise DTR pin is
+		 * high.
+		 */
+		dtrlc = UART_ACR_DTRLC_ENABLE_LOW;
+	} else {
+		/*
+		 * Set DTR line configuration of 95x UART to DTR mode (0,0).
+		 * In this mode the DTR pin is compatible with 16C450, 16C550,
+		 * 16C650 and 16c670 (i.e. normal).
+		 */
+		dtrlc = UART_ACR_DTRLC_COMPAT;
+	}
+
+	kuart_enhanced_mode(up, true);
+	kuart_dtr_line_config(up, dtrlc);
+	kuart_enhanced_mode(up, false);
+
+	if (kuart->flags & KUART_USE_CAPABILITY) {
+		/* activate selected physical interface */
+		kuart_set_phy_mode(kuart, mode);
+	}
+
+	kuart->mode = mode;
+
+	return 0;
+}
+
+static int kuart_probe(struct auxiliary_device *auxdev,
+		       const struct auxiliary_device_id *id)
+{
+	struct device *dev = &auxdev->dev;
+	struct uart_8250_port uart = {};
+	struct resource res;
+	struct kuart *kuart;
+	int retval;
+
+	kuart = devm_kzalloc(dev, sizeof(*kuart), GFP_KERNEL);
+	if (!kuart)
+		return -ENOMEM;
+	kuart->auxdev = container_of(auxdev, struct keba_uart_auxdev, auxdev);
+	kuart->flags = id->driver_data;
+	auxiliary_set_drvdata(auxdev, kuart);
+
+	/*
+	 * map only memory in front of UART registers, UART registers will be
+	 * mapped by serial port
+	 */
+	res = kuart->auxdev->io;
+	res.end = res.start + KUART_BASE - 1;
+	kuart->base = devm_ioremap_resource(dev, &res);
+	if (IS_ERR(kuart->base))
+		return PTR_ERR(kuart->base);
+
+	if (kuart->flags & KUART_USE_CAPABILITY) {
+		/*
+		 * supported modes are read from capability register, at least
+		 * one mode other than none must be supported
+		 */
+		kuart->capability = ioread8(kuart->base + KUART_CAPABILITY) &
+				    KUART_CAPABILITY_MASK;
+		if ((kuart->capability & ~KUART_CAPABILITY_NONE) == 0)
+			return -EIO;
+	}
+
+	spin_lock_init(&uart.port.lock);
+	uart.port.dev = dev;
+	uart.port.mapbase = kuart->auxdev->io.start + KUART_BASE;
+	uart.port.irq = kuart->auxdev->irq;
+	uart.port.uartclk = KUART_CLK;
+	uart.port.private_data = kuart;
+
+	/* 8 bit registers are 32 bit aligned => shift register offset */
+	uart.port.iotype = UPIO_MEM32;
+	uart.port.regshift = KUART_REGSHIFT;
+
+	/*
+	 * UART mixes 16550, 16750 and 16C950 (for RS485) standard => auto
+	 * configuration works best
+	 */
+	uart.port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_IOREMAP;
+
+	/*
+	 * UART supports RS485, RS422 and RS232 with switching of physical
+	 * interface
+	 */
+	uart.port.rs485_config = kuart_rs485_config;
+	if (kuart->flags & KUART_RS485) {
+		uart.port.rs485_supported.flags = SER_RS485_ENABLED |
+						  SER_RS485_RTS_ON_SEND;
+		uart.port.rs485.flags = SER_RS485_ENABLED |
+					SER_RS485_RTS_ON_SEND;
+	}
+	if (kuart->flags & KUART_USE_CAPABILITY) {
+		/* default mode priority is RS485 > RS422 > RS232 */
+		if (kuart->capability & KUART_CAPABILITY_RS422) {
+			uart.port.rs485_supported.flags |= SER_RS485_ENABLED |
+							   SER_RS485_RTS_ON_SEND |
+							   SER_RS485_MODE_RS422;
+			uart.port.rs485.flags = SER_RS485_ENABLED |
+						SER_RS485_RTS_ON_SEND |
+						SER_RS485_MODE_RS422;
+		}
+		if (kuart->capability & KUART_CAPABILITY_RS485) {
+			uart.port.rs485_supported.flags |= SER_RS485_ENABLED |
+							   SER_RS485_RTS_ON_SEND;
+			uart.port.rs485.flags = SER_RS485_ENABLED |
+						SER_RS485_RTS_ON_SEND;
+		}
+	}
+
+	retval = serial8250_register_8250_port(&uart);
+	if (retval < 0) {
+		dev_err(&auxdev->dev, "UART registration failed!\n");
+		return retval;
+	}
+	kuart->line = retval;
+
+	return 0;
+}
+
+static void kuart_remove(struct auxiliary_device *auxdev)
+{
+	struct kuart *kuart = auxiliary_get_drvdata(auxdev);
+
+	if (kuart->flags & KUART_USE_CAPABILITY)
+		kuart_set_phy_mode(kuart, KUART_MODE_NONE);
+
+	serial8250_unregister_port(kuart->line);
+}
+
+static const struct auxiliary_device_id kuart_devtype_aux[] = {
+	{ .name = "keba.rs485-uart", .driver_data = KUART_RS485 },
+	{ .name = "keba.rs232-uart", .driver_data = 0 },
+	{ .name = "keba.uart", .driver_data = KUART_USE_CAPABILITY },
+	{}
+};
+MODULE_DEVICE_TABLE(auxiliary, kuart_devtype_aux);
+
+static struct auxiliary_driver kuart_driver_aux = {
+	.name = KUART,
+	.id_table = kuart_devtype_aux,
+	.probe  = kuart_probe,
+	.remove = kuart_remove,
+};
+module_auxiliary_driver(kuart_driver_aux);
+
+MODULE_AUTHOR("Gerhard Engleder <eg@keba.com>");
+MODULE_DESCRIPTION("KEBA 8250 serial port driver");
+MODULE_LICENSE("GPL");