summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2016-12-02scsi: mpt3sas: Unblock device after controller resetSuganath Prabu S
commit 7ff723ad0f87feba43dda45fdae71206063dd7d4 upstream. While issuing any ATA passthrough command to firmware the driver will block the device. But it will unblock the device only if the I/O completes through the ISR path. If a controller reset occurs before command completion the device will remain in blocked state. Make sure we unblock the device following a controller reset if an ATA passthrough command was queued. [mkp: clarified patch description] Fixes: ac6c2a93bd07 ("mpt3sas: Fix for SATA drive in blocked state, after diag reset") Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-02device-dax: fail all private mapping attemptsDan Williams
commit 4cb19355ea19995941ccaad115dbfac6b75215ca upstream. The device-dax implementation originally tried to be tricky and allow private read-only mappings, but in the process allowed writable MAP_PRIVATE + MAP_NORESERVE mappings. For simplicity and predictability just fail all private mapping attempts since device-dax memory is statically allocated and will never support overcommit. Cc: Dave Hansen <dave.hansen@linux.intel.com> Fixes: dee410792419 ("/dev/dax, core: file operations and dax-mmap") Reported-by: Pawel Lebioda <pawel.lebioda@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-02device-dax: check devm_nsio_enable() return valueDan Williams
commit 6a84fb4b4e439a8ef0ce19ec7e7661ad76f655c9 upstream. If the dax_pmem driver is passed a resource that is already busy the driver probe attempt should fail with a message like the following: dax_pmem dax0.1: could not reserve region [mem 0x100000000-0x11fffffff] However, if we do not catch the error we crash for the obvious reason of accessing memory that is not mapped. BUG: unable to handle kernel paging request at ffffc90020001000 IP: [<ffffffff81496712>] __memcpy+0x12/0x20 [..] Call Trace: [<ffffffff815c4960>] ? nsio_rw_bytes+0x60/0x180 [<ffffffff815c6045>] nd_pfn_validate+0x75/0x320 [<ffffffff815c63a9>] nvdimm_setup_pfn+0xb9/0x5d0 [<ffffffff815c48ef>] ? devm_nsio_enable+0xff/0x110 [<ffffffff815cb699>] dax_pmem_probe+0x59/0x260 Fixes: ab68f2622136 ("/dev/dax, pmem: direct access to persistent memory") Reported-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-02xc2028: Fix use-after-free bug properlyTakashi Iwai
commit 22a1e7783e173ab3d86018eb590107d68df46c11 upstream. The commit 8dfbcc4351a0 ("[media] xc2028: avoid use after free") tried to address the reported use-after-free by clearing the reference. However, it's clearing the wrong pointer; it sets NULL to priv->ctrl.fname, but it's anyway overwritten by the next line memcpy(&priv->ctrl, p, sizeof(priv->ctrl)). OTOH, the actual code accessing the freed string is the strcmp() call with priv->fname: if (!firmware_name[0] && p->fname && priv->fname && strcmp(p->fname, priv->fname)) free_firmware(priv); where priv->fname points to the previous file name, and this was already freed by kfree(). For fixing the bug properly, this patch does the following: - Keep the copy of firmware file name in only priv->fname, priv->ctrl.fname isn't changed; - The allocation is done only when the firmware gets loaded; - The kfree() is called in free_firmware() commonly Fixes: commit 8dfbcc4351a0 ('[media] xc2028: avoid use after free') Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-02mmc: sdhci-of-esdhc: fixup PRESENT_STATE readMichael Walle
commit b0921d5c9ed6ffa8a4d6afc5ee5f136b87445f14 upstream. Since commit 87a18a6a5652 ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()") the ESDHC driver is broken: mmc0: Card stuck in programming state! __mmc_switch mmc0: error -110 whilst initialising MMC card Since this commit __mmc_switch() uses ->card_busy(), which is sdhci_card_busy() for the esdhc driver. sdhci_card_busy() uses the PRESENT_STATE register, specifically the DAT0 signal level bit. But the ESDHC uses a non-conformant PRESENT_STATE register, thus a read fixup is required to make the driver work again. Signed-off-by: Michael Walle <michael@walle.cc> Fixes: 87a18a6a5652 ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()") Acked-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-02thermal/powerclamp: add back module device tableJacob Pan
commit ec638db8cb9ddd5ca08b23f2835b6c9c15eb616d upstream. Commit 3105f234e0aba43e44e277c20f9b32ee8add43d4 replaced module cpu id table with a cpu feature check, which is logically correct. But we need the module device table to allow module auto loading. Fixes:3105f234 thermal/powerclamp: correct cpu support check Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-02scsi: mpt3sas: Fix secure erase premature terminationAndrey Grodzovsky
commit 18f6084a989ba1b38702f9af37a2e4049a924be6 upstream. This is a work around for a bug with LSI Fusion MPT SAS2 when perfoming secure erase. Due to the very long time the operation takes, commands issued during the erase will time out and will trigger execution of the abort hook. Even though the abort hook is called for the specific command which timed out, this leads to entire device halt (scsi_state terminated) and premature termination of the secure erase. Set device state to busy while ATA passthrough commands are in progress. [mkp: hand applied to 4.9/scsi-fixes, tweaked patch description] Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com> Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com> Cc: <linux-scsi@vger.kernel.org> Cc: Sathya Prakash <sathya.prakash@broadcom.com> Cc: Chaitra P B <chaitra.basappa@broadcom.com> Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com> Cc: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-02Fix USB CB/CBI storage devices with CONFIG_VMAP_STACK=yPetr Vandrovec
commit 2ce9d2272b98743b911196c49e7af5841381c206 upstream. Some code (all error handling) submits CDBs that are allocated on the stack. This breaks with CB/CBI code that tries to create URB directly from SCSI command buffer - which happens to be in vmalloced memory with vmalloced kernel stacks. Let's make copy of the command in usb_stor_CB_transport. Signed-off-by: Petr Vandrovec <petr@vandrovec.name> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-02USB: serial: ftdi_sio: add support for TI CC3200 LaunchPadDoug Brown
commit 9bfef729a3d11f04d12788d749a3ce6b47645734 upstream. This patch adds support for the TI CC3200 LaunchPad board, which uses a custom USB vendor ID and product ID. Channel A is used for JTAG, and channel B is used for a UART. Signed-off-by: Doug Brown <doug@schmorgal.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-02USB: serial: cp210x: add ID for the Zone DPMXPaul Jakma
commit 2ab13292d7a314fa45de0acc808e41aaad31989c upstream. The BRIM Brothers Zone DPMX is a bicycle powermeter. This ID is for the USB serial interface in its charging dock for the control pods, via which some settings for the pods can be modified. Signed-off-by: Paul Jakma <paul@jakma.org> Cc: Barry Redmond <barry@brimbrothers.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-02usb: chipidea: move the lock initialization to core filePeter Chen
commit a5d906bb261cde5f881a949d3b0fbaa285dcc574 upstream. This can fix below dump when the lock is accessed at host mode due to it is not initialized. [ 46.119638] INFO: trying to register non-static key. [ 46.124643] the code is fine but needs lockdep annotation. [ 46.130144] turning off the locking correctness validator. [ 46.135659] CPU: 0 PID: 690 Comm: cat Not tainted 4.9.0-rc3-00079-g4b75f1d #1210 [ 46.143075] Hardware name: Freescale i.MX6 SoloX (Device Tree) [ 46.148923] Backtrace: [ 46.151448] [<c010c460>] (dump_backtrace) from [<c010c658>] (show_stack+0x18/0x1c) [ 46.159038] r7:edf52000 [ 46.161412] r6:60000193 [ 46.163967] r5:00000000 [ 46.165035] r4:c0e25c2c [ 46.169109] [<c010c640>] (show_stack) from [<c03f58a4>] (dump_stack+0xb4/0xe8) [ 46.176362] [<c03f57f0>] (dump_stack) from [<c016d690>] (register_lock_class+0x4fc/0x56c) [ 46.184554] r10:c0e25d24 [ 46.187014] r9:edf53e70 [ 46.189569] r8:c1642444 [ 46.190637] r7:ee9da024 [ 46.193191] r6:00000000 [ 46.194258] r5:00000000 [ 46.196812] r4:00000000 [ 46.199185] r3:00000001 [ 46.203259] [<c016d194>] (register_lock_class) from [<c0171294>] (__lock_acquire+0x80/0x10f0) [ 46.211797] r10:c0e25d24 [ 46.214257] r9:edf53e70 [ 46.216813] r8:ee9da024 [ 46.217880] r7:c1642444 [ 46.220435] r6:edcd1800 [ 46.221502] r5:60000193 [ 46.224057] r4:00000000 [ 46.227953] [<c0171214>] (__lock_acquire) from [<c01726c0>] (lock_acquire+0x74/0x94) [ 46.235710] r10:00000001 [ 46.238169] r9:edf53e70 [ 46.240723] r8:edf53f80 [ 46.241790] r7:00000001 [ 46.244344] r6:00000001 [ 46.245412] r5:60000193 [ 46.247966] r4:00000000 [ 46.251866] [<c017264c>] (lock_acquire) from [<c096c8fc>] (_raw_spin_lock_irqsave+0x40/0x54) [ 46.260319] r7:ee1c6a00 [ 46.262691] r6:c062a570 [ 46.265247] r5:20000113 [ 46.266314] r4:ee9da014 [ 46.270393] [<c096c8bc>] (_raw_spin_lock_irqsave) from [<c062a570>] (ci_port_test_show+0x2c/0x70) [ 46.279280] r6:eebd2000 [ 46.281652] r5:ee9da010 [ 46.284207] r4:ee9da014 [ 46.286810] [<c062a544>] (ci_port_test_show) from [<c0248d04>] (seq_read+0x1ac/0x4f8) [ 46.294655] r9:edf53e70 [ 46.297028] r8:edf53f80 [ 46.299583] r7:ee1c6a00 [ 46.300650] r6:00000001 [ 46.303205] r5:00000000 [ 46.304273] r4:eebd2000 [ 46.306850] [<c0248b58>] (seq_read) from [<c039e864>] (full_proxy_read+0x54/0x6c) [ 46.314348] r10:00000000 [ 46.316808] r9:c0a6ad30 [ 46.319363] r8:edf53f80 [ 46.320430] r7:00020000 [ 46.322986] r6:b6de3000 [ 46.324053] r5:ee1c6a00 [ 46.326607] r4:c0248b58 [ 46.330505] [<c039e810>] (full_proxy_read) from [<c021ec98>] (__vfs_read+0x34/0x118) [ 46.338262] r9:edf52000 [ 46.340635] r8:c0107fc4 [ 46.343190] r7:00020000 [ 46.344257] r6:edf53f80 [ 46.346812] r5:c039e810 [ 46.347879] r4:ee1c6a00 [ 46.350447] [<c021ec64>] (__vfs_read) from [<c021fbd0>] (vfs_read+0x8c/0x11c) [ 46.357597] r9:edf52000 [ 46.359969] r8:c0107fc4 [ 46.362524] r7:edf53f80 [ 46.363592] r6:b6de3000 [ 46.366147] r5:ee1c6a00 [ 46.367214] r4:00020000 [ 46.369782] [<c021fb44>] (vfs_read) from [<c0220a4c>] (SyS_read+0x4c/0xa8) [ 46.376672] r8:c0107fc4 [ 46.379045] r7:00020000 [ 46.381600] r6:b6de3000 [ 46.382667] r5:ee1c6a00 [ 46.385222] r4:ee1c6a00 [ 46.387817] [<c0220a00>] (SyS_read) from [<c0107e20>] (ret_fast_syscall+0x0/0x1c) [ 46.395314] r7:00000003 [ 46.397687] r6:b6de3000 [ 46.400243] r5:00020000 [ 46.401310] r4:00020000 Fixes: 26c696c678c4 ("USB: Chipidea: rename struct ci13xxx variables from udc to ci") Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-02iommu/vt-d: Fix IOMMU lookup for SR-IOV Virtual FunctionsAshok Raj
commit 1c387188c60f53b338c20eee32db055dfe022a9b upstream. The VT-d specification (§8.3.3) says: ‘Virtual Functions’ of a ‘Physical Function’ are under the scope of the same remapping unit as the ‘Physical Function’. The BIOS is not required to list all the possible VFs in the scope tables, and arguably *shouldn't* make any attempt to do so, since there could be a huge number of them. This has been broken basically for ever — the VF is never going to match against a specific unit's scope, so it ends up being assigned to the INCLUDE_ALL IOMMU. Which was always actually correct by coincidence, but now we're looking at Root-Complex integrated devices with SR-IOV support it's going to start being wrong. Fix it to simply use pci_physfn() before doing the lookup for PCI devices. Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com> Signed-off-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-02iommu/vt-d: Fix PASID table allocationDavid Woodhouse
commit 910170442944e1f8674fd5ddbeeb8ccd1877ea98 upstream. Somehow I ended up with an off-by-three error in calculating the size of the PASID and PASID State tables, which triggers allocations failures as those tables unfortunately have to be physically contiguous. In fact, even the *correct* maximum size of 8MiB is problematic and is wont to lead to allocation failures. Since I have extracted a promise that this *will* be fixed in hardware, I'm happy to limit it on the current hardware to a maximum of 0x20000 PASIDs, which gives us 1MiB tables — still not ideal, but better than before. Reported by Mika Kuoppala <mika.kuoppala@linux.intel.com> and also by Xunlei Pang <xlpang@redhat.com> who submitted a simpler patch to fix only the allocation (and not the free) to the "correct" limit... which was still problematic. Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26gpio: pca953x: Fix corruption of other gpios in set_multiple.Phil Reid
commit 53f8d322234649b4d6f1515b20c127a577efd164 upstream. gpiod_set_array_value_complex does not clear the bits field. Therefore when the drivers set_multiple funciton is called bits outside the mask are undefined and can be either set or not. So bank_val needs to be masked with bank_mask before or with the reg_val cache. Fixes: b4818afeacbd ("gpio: pca953x: Add set_multiple to allow multiple") Signed-off-by: Phil Reid <preid@electromag.com.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26gpio: pca953x: Move memcpy into mutex lock for set multiplePhil Reid
commit 386377b5473043c09b2de40bfe5abfb0fc87e1b4 upstream. Need to ensure that reg_output is not updated while setting multiple bits. This makes the mutex locking behaviour for the set_multiple call consistent with that of the set_value call. Fixes: b4818afeacbd ("gpio: pca953x: Add set_multiple to allow multiple") Signed-off-by: Phil Reid <preid@electromag.com.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/cm: Mark stale CM id's whenever the mad agent was unregisteredMark Bloch
commit 9db0ff53cb9b43ed75bacd42a89c1a0ab048b2b0 upstream. When there is a CM id object that has port assigned to it, it means that the cm-id asked for the specific port that it should go by it, but if that port was removed (hot-unplug event) the cm-id was not updated. In order to fix that the port keeps a list of all the cm-id's that are planning to go by it, whenever the port is removed it marks all of them as invalid. This commit fixes a kernel panic which happens when running traffic between guests and we force reboot a guest mid traffic, it triggers a kernel panic: Call Trace: [<ffffffff815271fa>] ? panic+0xa7/0x16f [<ffffffff8152b534>] ? oops_end+0xe4/0x100 [<ffffffff8104a00b>] ? no_context+0xfb/0x260 [<ffffffff81084db2>] ? del_timer_sync+0x22/0x30 [<ffffffff8104a295>] ? __bad_area_nosemaphore+0x125/0x1e0 [<ffffffff81084240>] ? process_timeout+0x0/0x10 [<ffffffff8104a363>] ? bad_area_nosemaphore+0x13/0x20 [<ffffffff8104aabf>] ? __do_page_fault+0x31f/0x480 [<ffffffff81065df0>] ? default_wake_function+0x0/0x20 [<ffffffffa0752675>] ? free_msg+0x55/0x70 [mlx5_core] [<ffffffffa0753434>] ? cmd_exec+0x124/0x840 [mlx5_core] [<ffffffff8105a924>] ? find_busiest_group+0x244/0x9f0 [<ffffffff8152d45e>] ? do_page_fault+0x3e/0xa0 [<ffffffff8152a815>] ? page_fault+0x25/0x30 [<ffffffffa024da25>] ? cm_alloc_msg+0x35/0xc0 [ib_cm] [<ffffffffa024e821>] ? ib_send_cm_dreq+0xb1/0x1e0 [ib_cm] [<ffffffffa024f836>] ? cm_destroy_id+0x176/0x320 [ib_cm] [<ffffffffa024fb00>] ? ib_destroy_cm_id+0x10/0x20 [ib_cm] [<ffffffffa034f527>] ? ipoib_cm_free_rx_reap_list+0xa7/0x110 [ib_ipoib] [<ffffffffa034f590>] ? ipoib_cm_rx_reap+0x0/0x20 [ib_ipoib] [<ffffffffa034f5a5>] ? ipoib_cm_rx_reap+0x15/0x20 [ib_ipoib] [<ffffffff81094d20>] ? worker_thread+0x170/0x2a0 [<ffffffff8109b2a0>] ? autoremove_wake_function+0x0/0x40 [<ffffffff81094bb0>] ? worker_thread+0x0/0x2a0 [<ffffffff8109aef6>] ? kthread+0x96/0xa0 [<ffffffff8100c20a>] ? child_rip+0xa/0x20 [<ffffffff8109ae60>] ? kthread+0x0/0xa0 [<ffffffff8100c200>] ? child_rip+0x0/0x20 Fixes: a977049dacde ("[PATCH] IB: Add the kernel CM implementation") Signed-off-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/uverbs: Fix leak of XRC target QPsTariq Toukan
commit 5b810a242c28e1d8d64d718cebe75b79d86a0b2d upstream. The real QP is destroyed in case of the ref count reaches zero, but for XRC target QPs this call was missed and caused to QP leaks. Let's call to destroy for all flows. Fixes: 0e0ec7e0638e ('RDMA/core: Export ib_open_qp() to share XRC...') Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Noa Osherovich <noaos@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/hfi1: Remove incorrect IS_ERR checkDennis Dalessandro
commit 2b16056f845207967a32497f41cf92b57849f934 upstream. Remove IS_ERR check from caching code as the function being called does not actually return error pointers. Fixes: f19bd643dbde: "IB/hfi1: Prevent NULL pointer deferences in caching code" Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/core: Avoid unsigned int overflow in sg_alloc_tableMark Bloch
commit 3c7ba5760ab8eedec01159b267bb9bfcffe522ac upstream. sg_alloc_table gets unsigned int as parameter while the driver returns it as size_t. Check npages isn't greater than maximum unsigned int. Fixes: eeb8461e36c9 ("IB: Refactor umem to use linear SG table") Signed-off-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/mlx5: Fix NULL pointer dereference on debug printEli Cohen
commit a1ab8402d15d2305d2315d96ec3294bfdf16587e upstream. For XRC QP CQs may not exist. Check before attempting dereference. Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/mlx5: Fix fatal error dispatchingEli Cohen
commit dbaaff2a2caa03d472b5cc53a3fbfd415c97dc26 upstream. When an internal error condition is detected, make sure to set the device inactive after dispatching the event so ULPs can get a notification of this event. Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/mlx5: Fix memory leak in query deviceMajd Dibbiny
commit 90be7c8ab72853ff9fc407f01518a898df1f3045 upstream. We need to free dev->port when we fail to enable RoCE or initialize node data. Fixes: 0837e86a7a34 ('IB/mlx5: Add per port counters') Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/mlx5: Use cache line size to select CQE strideDaniel Jurgens
commit 16b0e0695a73b68d8ca40288c8f9614ef208917b upstream. When creating kernel CQs use 128B CQE stride if the cache line size is 128B, 64B otherwise. This prevents multiple CQEs from residing in a 128B cache line, which can cause retries when there are concurrent read and writes in one cache line. Tested with IPoIB on PPC64, saw ~5% throughput improvement. Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/mlx5: Validate requested RQT sizeMaor Gottlieb
commit efd7f40082a0dfd112eb87ff2124467a5739216f upstream. Validate that the requested size of RQT is supported by firmware. Fixes: c5f9092936fe ('IB/mlx5: Add Receive Work Queue Indirection table operations') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/mlx4: Fix create CQ error flowMatan Barak
commit 593ff73bcfdc79f79a8a0df55504f75ad3e5d1a9 upstream. Currently, if ib_copy_to_udata fails, the CQ won't be deleted from the radix tree and the HW (HW2SW). Fixes: 225c7b1feef1 ('IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/mlx4: Check gid_index return valueDaniel Jurgens
commit 37995116fecfce2b61ee3da6e73b3e394c6818f9 upstream. Check the returned GID index value and return an error if it is invalid. Fixes: 5070cd2239bd ('IB/mlx4: Replace mechanism for RoCE GID management') Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/rxe: Clear queue buffer when modifying QP to resetYonatan Cohen
commit aa75b07b478a774b1432e2df1be5cd8ae834de0f upstream. RXE resets the send-q only once in rxe_qp_init_req() when QP is created, but when the QP is reused after QP reset, the send-q holds previous garbage data. This garbage data wrongly fails CQEs that otherwise should have completed successfully. Fixes: 8700e3e7c485 ("Soft RoCE driver") Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com> Reviewed-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/rxe: Fix handling of erroneous WRYonatan Cohen
commit 002e062e13db10973adb8302f231e48b477c7ccf upstream. To correctly handle a erroneous WR this fix does the following 1. Make sure the bad WQE causes a user completion event. 2. Call rxe_completer to handle the erred WQE. Before the fix, when rxe_requester found a bad WQE, it changed its status to IB_WC_LOC_PROT_ERR and exit with 0 for non RC QPs. If this was the 1st WQE then there would be no ACK to invoke the completer and this bad WQE would be stuck in the QP's send-q. On top of that the requester exiting with 0 caused rxe_do_task to endlessly invoke rxe_requester, resulting in a soft-lockup attached below. In case the WQE was not the 1st and rxe_completer did get a chance to handle the bad WQE, it did not cause a complete event since the WQE's IB_SEND_SIGNALED flag was not set. Setting WQE status to IB_SEND_SIGNALED is subject to IBA spec version 1.2.1, section 10.7.3.1 Signaled Completions. NMI watchdog: BUG: soft lockup - CPU#7 stuck for 22s! [<ffffffffa0590145>] ? rxe_pool_get_index+0x35/0xb0 [rdma_rxe] [<ffffffffa05952ec>] lookup_mem+0x3c/0xc0 [rdma_rxe] [<ffffffffa0595534>] copy_data+0x1c4/0x230 [rdma_rxe] [<ffffffffa058c180>] rxe_requester+0x9d0/0x1100 [rdma_rxe] [<ffffffff8158e98a>] ? kfree_skbmem+0x5a/0x60 [<ffffffffa05962c9>] rxe_do_task+0x89/0xf0 [rdma_rxe] [<ffffffffa05963e2>] rxe_run_task+0x12/0x30 [rdma_rxe] [<ffffffffa059110a>] rxe_post_send+0x41a/0x550 [rdma_rxe] [<ffffffff811ef922>] ? __kmalloc+0x182/0x200 [<ffffffff816ba512>] ? down_read+0x12/0x40 [<ffffffffa054bd32>] ib_uverbs_post_send+0x532/0x540 [ib_uverbs] [<ffffffff815f8722>] ? tcp_sendmsg+0x402/0xb80 [<ffffffffa05453dc>] ib_uverbs_write+0x18c/0x3f0 [ib_uverbs] [<ffffffff81623c2e>] ? inet_recvmsg+0x7e/0xb0 [<ffffffff8158764d>] ? sock_recvmsg+0x3d/0x50 [<ffffffff81215b87>] __vfs_write+0x37/0x140 [<ffffffff81216892>] vfs_write+0xb2/0x1b0 [<ffffffff81217ce5>] SyS_write+0x55/0xc0 [<ffffffff816bc672>] entry_SYSCALL_64_fastpath+0x1a/0xa Fixes: 8700e3e7c485 ("Soft RoCE driver") Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com> Reviewed-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/rxe: Fix kernel panic in UDP tunnel with GRO and RX checksumYonatan Cohen
commit 1454ca3a97e147bb91e98b087446c39cf6692a48 upstream. Missing initialization of udp_tunnel_sock_cfg causes to following kernel panic, while kernel tries to execute gro_receive(). While being there, we converted udp_port_cfg to use the same initialization scheme as udp_tunnel_sock_cfg. ------------[ cut here ]------------ kernel tried to execute NX-protected page - exploit attempt? (uid: 0) BUG: unable to handle kernel paging request at ffffffffa0588c50 IP: [<ffffffffa0588c50>] __this_module+0x50/0xffffffffffff8400 [ib_rxe] PGD 1c09067 PUD 1c0a063 PMD bb394067 PTE 80000000ad5e8163 Oops: 0011 [#1] SMP Modules linked in: ib_rxe ip6_udp_tunnel udp_tunnel CPU: 5 PID: 0 Comm: swapper/5 Not tainted 4.7.0-rc3+ #2 Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011 task: ffff880235e4e680 ti: ffff880235e68000 task.ti: ffff880235e68000 RIP: 0010:[<ffffffffa0588c50>] [<ffffffffa0588c50>] __this_module+0x50/0xffffffffffff8400 [ib_rxe] RSP: 0018:ffff880237343c80 EFLAGS: 00010282 RAX: 00000000dffe482d RBX: ffff8800ae330900 RCX: 000000002001b712 RDX: ffff8800ae330900 RSI: ffff8800ae102578 RDI: ffff880235589c00 RBP: ffff880237343cb0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800ae33e262 R13: ffff880235589c00 R14: 0000000000000014 R15: ffff8800ae102578 FS: 0000000000000000(0000) GS:ffff880237340000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffa0588c50 CR3: 0000000001c06000 CR4: 00000000000006e0 Stack: ffffffff8160860e ffff8800ae330900 ffff8800ae102578 0000000000000014 000000000000004e ffff8800ae102578 ffff880237343ce0 ffffffff816088fb 0000000000000000 ffff8800ae330900 0000000000000000 00000000ffad0000 Call Trace: <IRQ> [<ffffffff8160860e>] ? udp_gro_receive+0xde/0x130 [<ffffffff816088fb>] udp4_gro_receive+0x10b/0x2d0 [<ffffffff81611373>] inet_gro_receive+0x1d3/0x270 [<ffffffff81594e29>] dev_gro_receive+0x269/0x3b0 [<ffffffff81595188>] napi_gro_receive+0x38/0x120 [<ffffffffa011caee>] mlx5e_handle_rx_cqe+0x27e/0x340 [mlx5_core] [<ffffffffa011d076>] mlx5e_poll_rx_cq+0x66/0x6d0 [mlx5_core] [<ffffffffa011d7ae>] mlx5e_napi_poll+0x8e/0x400 [mlx5_core] [<ffffffff815949a0>] net_rx_action+0x160/0x380 [<ffffffff816a9197>] __do_softirq+0xd7/0x2c5 [<ffffffff81085c35>] irq_exit+0xf5/0x100 [<ffffffff816a8f16>] do_IRQ+0x56/0xd0 [<ffffffff816a6dcc>] common_interrupt+0x8c/0x8c <EOI> [<ffffffff81061f96>] ? native_safe_halt+0x6/0x10 [<ffffffff81037ade>] default_idle+0x1e/0xd0 [<ffffffff8103828f>] arch_cpu_idle+0xf/0x20 [<ffffffff810c37dc>] default_idle_call+0x3c/0x50 [<ffffffff810c3b13>] cpu_startup_entry+0x323/0x3c0 [<ffffffff81050d8c>] start_secondary+0x15c/0x1a0 RIP [<ffffffffa0588c50>] __this_module+0x50/0xffffffffffff8400 [ib_rxe] RSP <ffff880237343c80> CR2: ffffffffa0588c50 ---[ end trace 489ee31fa7614ac5 ]--- Kernel panic - not syncing: Fatal exception in interrupt Kernel Offset: disabled ---[ end Kernel panic - not syncing: Fatal exception in interrupt ------------[ cut here ]------------ Fixes: 8700e3e7c485 ("Soft RoCE driver") Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com> Reviewed-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26IB/rxe: Update qp state for user queryYonatan Cohen
commit 6d931308f55faaef3f30bd0346c47f99528b229d upstream. The method rxe_qp_error() transitions QP to error state and make sure the QP is drained. It did not though update the QP state for user's query. This patch fixes this. Fixes: 8700e3e7c485 ("Soft RoCE driver") Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com> Reviewed-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26PM / sleep: don't suspend parent when async child suspend_{noirq, late} failsBrian Norris
commit 6f75c3fd56daf547d684127a7f83c283c3c160d1 upstream. Consider two devices, A and B, where B is a child of A, and B utilizes asynchronous suspend (it does not matter whether A is sync or async). If B fails to suspend_noirq() or suspend_late(), or is interrupted by a wakeup (pm_wakeup_pending()), then it aborts and sets the async_error variable. However, device A does not (immediately) check the async_error variable; it may continue to run its own suspend_noirq()/suspend_late() callback. This is bad. We can resolve this problem by doing our error and wakeup checking (particularly, for the async_error flag) after waiting for children to suspend, instead of before. This also helps align the logic for the noirq and late suspend cases with the logic in __device_suspend(). It's easy to observe this erroneous behavior by, for example, forcing a device to sleep a bit in its suspend_noirq() (to ensure the parent is waiting for the child to complete), then return an error, and watch the parent suspend_noirq() still get called. (Or similarly, fake a wakeup event at the right (or is it wrong?) time.) Fixes: de377b397272 (PM / sleep: Asynchronous threads for suspend_late) Fixes: 28b6fd6e3779 (PM / sleep: Asynchronous threads for suspend_noirq) Reported-by: Jeffy Chen <jeffy.chen@rock-chips.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26uwb: fix device reference leaksJohan Hovold
commit d6124b409ca33c100170ffde51cd8dff761454a1 upstream. This subsystem consistently fails to drop the device reference taken by class_find_device(). Note that some of these lookup functions already take a reference to the returned data, while others claim no reference is needed (or does not seem need one). Fixes: 183b9b592a62 ("uwb: add the UWB stack (core files)") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26mfd: core: Fix device reference leak in mfd_clone_cellJohan Hovold
commit 722f191080de641f023feaa7d5648caf377844f5 upstream. Make sure to drop the reference taken by bus_find_device_by_name() before returning from mfd_clone_cell(). Fixes: a9bbba996302 ("mfd: add platform_device sharing support for mfd") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26iwlwifi: mvm: wake the wait queue when the RX sync counter is zeroSara Sharon
commit 3a732c65de427fdae67a243fd331356034b5a1e8 upstream. When we sync the RX queues the driver waits to receive echo notification on all the RX queues. The wait queue is set with timeout until all queues have received the notification. However, iwl_mvm_rx_queue_notif() never woke up the wait queue, with the result of the counter value being checked only when the timeout expired. This may cause a latency of up to 1 second. Fixes: 0636b938214c ("iwlwifi: mvm: implement driver RX queues sync command") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26iwlwifi: mvm: fix d3_test with unified D0/D3 imagesLuca Coelho
commit 85cd69b8f1f7e289fe931a82889e673fd0f04842 upstream. When a unified D0/D3 image is used, we don't restart the FW in the D0->D3->D0 transitions. Therefore, the d3_test functionality should not call ieee8021_restart_hw() when the resuming either. Fixes: commit 23ae61282b88 ("iwlwifi: mvm: Do not switch to D3 image on suspend") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26iwlwifi: mvm: fix netdetect starting/stopping for unified imagesLuca Coelho
commit 5a143db8c4a28dab6423cb6197e9f1389da375f2 upstream. With unified images, we need to make sure the net-detect scan is stopped after resuming, since we don't restart the FW. Also, we need to make sure we check if there are enough scan slots available to run it, as we do with other scans. Fixes: commit 23ae61282b88 ("iwlwifi: mvm: Do not switch to D3 image on suspend") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26iwlwifi: pcie: mark command queue lock with separate lockdep classJohannes Berg
commit faead41cc7213ccef5a58c1bf518ac24816fe8a6 upstream. Emmanuel reports that when CMD_WANT_ASYNC_CALLBACK is used by mvm, the callback will be called with the command queue lock held, and mvm will try to stop all (other) TX queues, which acquires their locks - this caused a false lockdep recursive locking report. Suppress this report by marking the command queue lock with a new, separate, lock class so lockdep can tell the difference between the two types of queues. Fixes: 156f92f2b471 ("iwlwifi: block the queues when we send ADD_STA for uAPSD") Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26iwlwifi: pcie: fix SPLC structure parsingLuca Coelho
commit e0d9727c111a5917a1184c71c1a8e6f78c7fc41d upstream. The SPLC data parsing is too restrictive and was not trying find the correct element for WiFi. This causes problems with some BIOSes where the SPLC method exists, but doesn't have a WiFi entry on the first element of the list. The domain type values are also incorrect according to the specification. Fix this by complying with the actual specification. Additionally, replace all occurrences of SPLX to SPLC, since SPLX is only a structure internal to the ACPI tables, and may not even exist. Fixes: bcb079a14d75 ("iwlwifi: pcie: retrieve and parse ACPI power limitations") Reported-by: Chris Rorvick <chris@rorvick.com> Tested-by: Paul Bolle <pebolle@tiscali.nl> Tested-by: Chris Rorvick <chris@rorvick.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26rtc: omap: Fix selecting external oscLokesh Vutla
commit 3984903a2e3906d3def220e688040ce93368200a upstream. RTC can be clocked from an external 32KHz oscillator, or from the Peripheral PLL. The RTC has an internal oscillator buffer to support direct operation with a crystal. ---------------------------------------- | Device --------- | | | | | | | RTCSS | | | --------- | | | OSC |<------| RTC | | | | |------>| OSC |--- | | | | -------- | | | | | ----|clk | | | -------- | | | | | | PRCM |--- | | | | -------- -------- | ---------------------------------------- The RTC functional clock is sourced by default from the clock derived from the Peripheral PLL. In order to select source as external osc clk the following changes needs to be done: - Enable the RTC OSC (RTC_OSC_REG[4]OSC32K_GZ = 0) - Enable the clock mux(RTC_OSC_REG[6]K32CLK_EN = 1) - Select the external clock source (RTC_OSC_REG[3]32KCLK_SEL = 1) Fixes: 399cf0f63f6f2 ("rtc: omap: Add external clock enabling support") Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26clk: imx: fix integer overflow in AV PLL round rateEmil Lundmark
commit 5c2f117a22e46a4afee6ddee29b653a7a2a6b41f upstream. Since 'parent_rate * mfn' may overflow 32 bits, the result should be stored using 64 bits. The problem was discovered when trying to set the rate of the audio PLL (pll4_post_div) on an i.MX6Q. The desired rate was 196.608 MHz, but the actual rate returned was 192.000570 MHz. The round rate function should have been able to return 196.608 MHz, i.e., the desired rate. Fixes: ba7f4f557eb6 ("clk: imx: correct AV PLL rate formula") Cc: Anson Huang <b20788@freescale.com> Signed-off-by: Emil Lundmark <emil@limesaudio.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26clk: mmp: mmp2: fix return value check in mmp2_clk_init()Wei Yongjun
commit a29e52a6e66f4c0c895e7083e4bad2e7957f1fb5 upstream. Fix the retrn value check which testing the wrong variable in mmp2_clk_init(). Fixes: 1ec770d92a62 ("clk: mmp: add mmp2 DT support for clock driver") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26clk: mmp: pxa168: fix return value check in pxa168_clk_init()Wei Yongjun
commit deab07261d54b4db7b627d38e0efac97f176c6d6 upstream. Fix the retrn value check which testing the wrong variable in pxa168_clk_init(). Fixes: ab08aefcd12d ("clk: mmp: add pxa168 DT support for clock driver") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26clk: mmp: pxa910: fix return value check in pxa910_clk_init()Wei Yongjun
commit 10f2bfb092e3b49000526c02cfe8b2abbbdbb752 upstream. Fix the retrn value check which testing the wrong variable in pxa910_clk_init(). Fixes: 2bc61da9f7ff ("clk: mmp: add pxa910 DT support for clock driver") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26virtio-net: drop legacy features in virtio 1 modeMichael S. Tsirkin
commit f3358507c11999c91abf54744658bccd49b5879c upstream. Virtio 1.0 spec says VIRTIO_F_ANY_LAYOUT and VIRTIO_NET_F_GSO are legacy-only feature bits. Do not negotiate them in virtio 1 mode. Note this is a spec violation so we need to backport it to stable/downstream kernels. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26drm/i915: Assume non-DP++ port if dvo_port is HDMI and there's no AUX ch ↵Ville Syrjälä
specified in the VBT commit bc9db5ad3253c8e17969bd802c47b73e63f125ab upstream. My heuristic for detecting type 1 DVI DP++ adaptors based on the VBT port information apparently didn't survive the reality of buggy VBTs. In this particular case we have a machine with a natice HDMI port, but the VBT tells us it's a DP++ port based on its capabilities. The dvo_port information in VBT does claim that we're dealing with a HDMI port though, but we have other machines which do the same even when they actually have DP++ ports. So that piece of information alone isn't sufficient to tell the two apart. After staring at a bunch of VBTs from various machines, I have to conclude that the only other semi-reliable clue we can use is the presence of the AUX channel in the VBT. On this particular machine AUX channel is specified as zero, whereas on some of the other machines which listed the DP++ port as HDMI have a non-zero AUX channel. I've also seen VBTs which have dvo_port a DP but have a zero AUX channel. I believe those we need to treat as DP ports, so we'll limit the AUX channel check to just the cases where dvo_port is HDMI. If we encounter any more serious failures with this heuristic I think we'll have to have to throw it out entirely. But that could mean that there is a risk of type 1 DVI dongle users getting greeted by a black screen, so I'd rather not go there unless absolutely necessary. v2: Remove the duplicate PORT_A check (Daniel) Fix some typos in the commit message Cc: Daniel Otero <daniel.otero@outlook.com> Tested-by: Daniel Otero <daniel.otero@outlook.com> Fixes: d61992565bd3 ("drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97994 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1478884464-14251-1-git-send-email-ville.syrjala@linux.intel.com Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (cherry picked from commit 7a17995a3dc8613f778a9e2fd20e870f17789544) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26drm/i915: Refresh that status of MST capable connectors in ->detect()Ville Syrjälä
commit fc22b787890f9f9067fd130feec42297a4ee62ba upstream. Once we've determined that the sink is MST capable we never end up running through the full detect cycle again, despite getting HPDs. Fix tht by ripping out the incorrect piece of code responsible. This got broken when I moved the long HPD handling to the ->detect() hook, but failed to remove the leftover code. Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com> Cc: drm-intel-fixes@lists.freedesktop.org Cc: Rui Tiago Matos <tiagomatos@gmail.com> Tested-by: Rui Tiago Matos <tiagomatos@gmail.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98323 Cc: Kirill A. Shutemov <kirill@shutemov.name> Tested-by: Kirill A. Shutemov <kirill@shutemov.name> References: https://bugs.freedesktop.org/show_bug.cgi?id=98306 Fixes: 1015811609c0 ("drm/i915: Move long hpd handling into the hotplug work") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1477057478-29328-1-git-send-email-ville.syrjala@linux.intel.com Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (cherry picked from commit 1aab956c7b8872fb6976328316bfad62c6e67cf8) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26drm/amdgpu: Attach exclusive fence to prime exported bo's. (v5)Mario Kleiner
commit 8e94a46c1770884166b31adc99eba7da65a446a7 upstream. External clients which import our bo's wait only for exclusive dmabuf-fences, not on shared ones, ditto for bo's which we import from external providers and write to. Therefore attach exclusive fences on prime shared buffers if our exported buffer gets imported by an external client, or if we import a buffer from an external exporter. See discussion in thread: https://lists.freedesktop.org/archives/dri-devel/2016-October/122370.html Prime export tested on Intel iGPU + AMD Tonga dGPU as DRI3/Present Prime render offload, and with the Tonga standalone as primary gpu. v2: Add a wait for all shared fences before prime export, as suggested by Christian Koenig. v3: - Mark buffer prime_exported in amdgpu_gem_prime_pin, so we only use the exclusive fence when exporting a bo to external clients like a separate iGPU, but not when exporting/importing from/to ourselves as part of regular DRI3 fd passing. - Propagate failure of reservation_object_wait_rcu back to caller. v4: - Switch to a prime_shared_count counter instead of a flag, which gets in/decremented on prime_pin/unpin, so we can switch back to shared fences if all clients detach from our exported bo. - Also switch to exclusive fence for prime imported bo's. v5: - Drop lret, instead use int ret -> long ret, as proposed by Christian. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95472 Tested-by: Mike Lothian <mike@fireburn.co.uk> (v1) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reviewed-by: Christian König <christian.koenig@amd.com>. Cc: Christian König <christian.koenig@amd.com> Cc: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26crypto: caam - do not register AES-XTS mode on LP unitsSven Ebenfeld
commit 83d2c9a9c17b1e9f23a3a0c24c03cd18e4b02520 upstream. When using AES-XTS on a Wandboard, we receive a Mode error: caam_jr 2102000.jr1: 20001311: CCB: desc idx 19: AES: Mode error. According to the Security Reference Manual, the Low Power AES units of the i.MX6 do not support the XTS mode. Therefore we must not register XTS implementations in the Crypto API. Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Fixes: c6415a6016bf "crypto: caam - add support for acipher xts(aes)" Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2016-11-26i2c: i2c-mux-pca954x: fix deselect enabling for device-treeAlex Hemme
commit ad092de60f865c1ad94221bd06d381ecea446cc8 upstream. Deselect functionality can be ignored for device-trees with "i2c-mux-idle-disconnect" entries if no platform_data is available. By enabling the deselect functionality outside the platform_data block the logic works as it did in previous kernels. Fixes: 7fcac9807175 ("i2c: i2c-mux-pca954x: convert to use an explicit i2c mux core") Signed-off-by: Alex Hemme <ahemme@cisco.com> Signed-off-by: Ziyang Wu <ziywu@cisco.com> [touched up a few minor issues /peda] Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-26i2c: mux: fix up dependenciesLinus Walleij
commit 93d710a65ef02fb7fd48ae207e78f460bd7a6089 upstream. We get the following build error from UM Linux after adding an entry to drivers/iio/gyro/Kconfig that issues "select I2C_MUX": ERROR: "devm_ioremap_resource" [drivers/i2c/muxes/i2c-mux-reg.ko] undefined! ERROR: "of_address_to_resource" [drivers/i2c/muxes/i2c-mux-reg.ko] undefined! It appears that the I2C mux core code depends on HAS_IOMEM for historical reasons, while CONFIG_I2C_MUX_REG does *not* have a direct dependency on HAS_IOMEM. This creates a situation where a allyesconfig or allmodconfig for UM Linux will select I2C_MUX, and will implicitly enable I2C_MUX_REG as well, and the compilation will fail for the register driver. Fix this up by making I2C_MUX_REG depend on HAS_IOMEM and removing the dependency from I2C_MUX. Reported-by: kbuild test robot <fengguang.wu@intel.com> Reported-by: Jonathan Cameron <jic23@jic23.retrosnub.co.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jonathan Cameron <jic23@kernel.org> Acked-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.46.0) at 2026-01-21 23:08:17 +0000