| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 848b09d53d923b4caee5491f57a5c5b22d81febc ]
The Dell AW1022z is an RTL8156B based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://patch.msgid.link/20250206224033.980115-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 4d27afbf256028a1f54363367f30efc8854433c3 upstream.
The Source can drop its output voltage to the minimum of the requested
PPS APDO voltage range when it is in Current Limit Mode. If this voltage
falls within the range of vPpsShutdown, the Source initiates a Hard
Reset and discharges Vbus. However, currently the Sink may disconnect
before the voltage reaches vPpsShutdown, leading to unexpected behavior.
Prevent premature disconnection by setting the Sink's disconnect
threshold to the minimum vPpsShutdown value. Additionally, consider the
voltage drop due to IR drop when calculating the appropriate threshold.
This ensures a robust and reliable interaction between the Source and
Sink during SPR PPS Current Limit Mode operation.
Fixes: 4288debeaa4e ("usb: typec: tcpci: Fix up sink disconnect thresholds for PD")
Cc: stable <stable@kernel.org>
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250114142435.2093857-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 130eac4170859fb368681e00d390f20f44bbf27b upstream.
A recent patch caused an unused-function warning in builds with
CONFIG_PM disabled, after the function became marked 'static':
drivers/usb/host/xhci-pci.c:91:13: error: 'xhci_msix_sync_irqs' defined but not used [-Werror=unused-function]
91 | static void xhci_msix_sync_irqs(struct xhci_hcd *xhci)
| ^~~~~~~~~~~~~~~~~~~
This could be solved by adding another #ifdef, but as there is
a trend towards removing CONFIG_PM checks in favor of helper
macros, do the same conversion here and use pm_ptr() to get
either a function pointer or NULL but avoid the warning.
As the hidden functions reference some other symbols, make
sure those are visible at compile time, at the minimal cost of
a few extra bytes for 'struct usb_device'.
Fixes: 9abe15d55dcc ("xhci: Move xhci MSI sync function to to xhci-pci")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230328131114.1296430-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f0db885fb05d35befa81896db6b19eb3ee9ccdfe ]
USB3.2 spec section 9.2.5.4 quotes that a function may signal that
it wants to exit from Function Suspend by sending a Function
Wake Notification to the host if it is enabled for function
remote wakeup. Add an api in composite layer that can be used
by the function drivers to support this feature. Also expose
a gadget op so that composite layer can trigger a wakeup request
to the UDC driver.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Link: https://lore.kernel.org/r/1679694482-16430-4-git-send-email-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 705e3ce37bcc ("usb: dwc3: core: Fix system suspend on TI AM62 platforms")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 04e906839a053f092ef53f4fb2d610983412b904 upstream.
The work can submit URBs and the URBs can schedule the work.
This cycle needs to be broken, when a device is to be stopped.
Use a flag to do so.
This is a design issue as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
CC: stable@vger.kernel.org
Link: https://patch.msgid.link/20240919123525.688065-1-oneukum@suse.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5a1ccf0c72cf917ff3ccc131d1bb8d19338ffe52 ]
This patch introduces a new USB quirk,
USB_QUIRK_SHORT_SET_ADDRESS_REQ_TIMEOUT, which modifies the timeout value
for the SET_ADDRESS request. The standard timeout for USB request/command
is 5000 ms, as recommended in the USB 3.2 specification (section 9.2.6.1).
However, certain scenarios, such as connecting devices through an APTIV
hub, can lead to timeout errors when the device enumerates as full speed
initially and later switches to high speed during chirp negotiation.
In such cases, USB analyzer logs reveal that the bus suspends for
5 seconds due to incorrect chirp parsing and resumes only after two
consecutive timeout errors trigger a hub driver reset.
Packet(54) Dir(?) Full Speed J(997.100 us) Idle( 2.850 us)
_______| Time Stamp(28 . 105 910 682)
_______|_____________________________________________________________Ch0
Packet(55) Dir(?) Full Speed J(997.118 us) Idle( 2.850 us)
_______| Time Stamp(28 . 106 910 632)
_______|_____________________________________________________________Ch0
Packet(56) Dir(?) Full Speed J(399.650 us) Idle(222.582 us)
_______| Time Stamp(28 . 107 910 600)
_______|_____________________________________________________________Ch0
Packet(57) Dir Chirp J( 23.955 ms) Idle(115.169 ms)
_______| Time Stamp(28 . 108 532 832)
_______|_____________________________________________________________Ch0
Packet(58) Dir(?) Full Speed J (Suspend)( 5.347 sec) Idle( 5.366 us)
_______| Time Stamp(28 . 247 657 600)
_______|_____________________________________________________________Ch0
This 5-second delay in device enumeration is undesirable, particularly
in automotive applications where quick enumeration is crucial
(ideally within 3 seconds).
The newly introduced quirks provide the flexibility to align with a
3-second time limit, as required in specific contexts like automotive
applications.
By reducing the SET_ADDRESS request timeout to 500 ms, the
system can respond more swiftly to errors, initiate rapid recovery, and
ensure efficient device enumeration. This change is vital for scenarios
where rapid smartphone enumeration and screen projection are essential.
To use the quirk, please write "vendor_id:product_id:p" to
/sys/bus/usb/drivers/hub/module/parameter/quirks
For example,
echo "0x2c48:0x0132:p" > /sys/bus/usb/drivers/hub/module/parameters/quirks"
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231027152029.104363-2-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a769154c7cac037914ba375ae88aae55b2c853e0 ]
- The HCD address_device callback now accepts a user-defined timeout value
in milliseconds, providing better control over command execution times.
- The default timeout value for the address_device command has been set
to 5000 ms, aligning with the USB 3.2 specification. However, this
timeout can be adjusted as needed.
- The xhci_setup_device function has been updated to accept the timeout
value, allowing it to specify the maximum wait time for the command
operation to complete.
- The hub driver has also been updated to accommodate the newly added
timeout parameter during the SET_ADDRESS request.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231027152029.104363-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 5a1ccf0c72cf ("usb: new quirk to reduce the SET_ADDRESS request timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b93c2a68f3d9dc98ec30dcb342ae47c1c8d09d18 ]
The wakeup bit in the bmAttributes field indicates whether the device
is configured for remote wakeup. But this field should be allowed to
set only if the UDC supports such wakeup mechanism. So configure this
field based on UDC capability. Also inform the UDC whether the device
is configured for remote wakeup by implementing a gadget op.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Link: https://lore.kernel.org/r/1679694482-16430-2-git-send-email-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7037d95a047cd89b1f680eed253c6ab586bef1ed ]
The ASUS USB-C2500 is an RTL8156 based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Kelly Kane <kelly@hawknetworks.com>
Link: https://lore.kernel.org/r/20231203011712.6314-1-kelly@hawknetworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 72f93a3136ee18fd59fa6579f84c07e93424681e ]
The D-Link DUB-E250 is an RTL8156 based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Antonio Napolitano <anton@polit.no>
Link: https://lore.kernel.org/r/CV200KJEEUPC.WPKAHXCQJ05I@mercurius
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 7037d95a047c ("r8152: add vendor/device ID pair for ASUS USB-C2500")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 12e6ac69cc7e7d3367599ae26a92a0f9a18bc728 ]
Some NXP processors using ChipIdea USB IP have a bug when frame babble is
detected.
Issue description:
In USB camera test, our controller is host in HS mode. In ISOC IN, when
device sends data across the micro frame, it causes the babble in host
controller. This will clear the PE bit. In spec, it also requires to set
the PEC bit and then set the PCI bit. Without the PCI interrupt, the
software does not know the PE is cleared.
This will add a flag CI_HDRC_HAS_PORTSC_PEC_MISSED to some impacted
platform datas. And the ehci host driver will assert PEC by SW when
specific conditions are satisfied.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230809024432.535160-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f23643306430f86e2f413ee2b986e0773e79da31 upstream.
Some usb hubs will negotiate DisplayPort Alt mode with the device
but will then negotiate a data role swap after entering the alt
mode. The data role swap causes the device to unregister all alt
modes, however the usb hub will still send Attention messages
even after failing to reregister the Alt Mode. type_altmode_attention
currently does not verify whether or not a device's altmode partner
exists, which results in a NULL pointer error when dereferencing
the typec_altmode and typec_altmode_ops belonging to the altmode
partner.
Verify the presence of a device's altmode partner before sending
the Attention message to the Alt Mode driver.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230814180559.923475-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 23e60c8daf5ec2ab1b731310761b668745fcf6ed upstream.
According the "USB Type-C Port Controller Interface Specification v2.0"
the TCPC sets the fault status register bit-7
(AllRegistersResetToDefault) once the registers have been reset to
their default values.
This triggers an alert(-irq) on PTN5110 devices albeit we do mask the
fault-irq, which may cause a kernel hang. Fix this generically by writing
a one to the corresponding bit-7.
Cc: stable@vger.kernel.org
Fixes: 74e656d6b055 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Reported-by: "Angus Ainslie (Purism)" <angus@akkea.ca>
Closes: https://lore.kernel.org/all/20190508002749.14816-2-angus@akkea.ca/
Reported-by: Christian Bach <christian.bach@scs.ch>
Closes: https://lore.kernel.org/regressions/ZR0P278MB07737E5F1D48632897D51AC3EB329@ZR0P278MB0773.CHEP278.PROD.OUTLOOK.COM/t/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230816172502.1155079-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
detection"
[ Upstream commit df49f2a0ac4a34c0cb4b5c233fcfa0add644c43c ]
This reverts commit edd60d24bd858cef165274e4cd6cab43bdc58d15.
Heikki reports that this should not be a global flag just to work around
one broken driver and should be fixed differently, so revert it.
Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Fixes: edd60d24bd85 ("usb: common: usb-conn-gpio: Set last role to unknown before initial detection")
Link: https://lore.kernel.org/r/ZImE4L3YgABnCIsP@kuha.fi.intel.com
Cc: Prashanth K <quic_prashk@quicinc.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit edd60d24bd858cef165274e4cd6cab43bdc58d15 ]
Currently if we bootup a device without cable connected, then
usb-conn-gpio won't call set_role() since last_role is same as
current role. This happens because during probe last_role gets
initialised to zero.
To avoid this, added a new constant in enum usb_role, last_role
is set to USB_ROLE_UNKNOWN before performing initial detection.
While at it, also handle default case for the usb_role switch
in cdns3, intel-xhci-usb-role-switch & musb/jz4740 to avoid
build warnings.
Fixes: 4602f3bff266 ("usb: common: add USB GPIO based connection detection driver")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <1685544074-17337-1-git-send-email-quic_prashk@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0143d148d1e882fb1538dc9974c94d63961719b9 upstream.
The current implementation of usbdev_mmap uses usb_alloc_coherent to
allocate memory pages that will later be mapped into the user space.
Meanwhile, usb_alloc_coherent employs three different methods to
allocate memory, as outlined below:
* If hcd->localmem_pool is non-null, it uses gen_pool_dma_alloc to
allocate memory;
* If DMA is not available, it uses kmalloc to allocate memory;
* Otherwise, it uses dma_alloc_coherent.
However, it should be noted that gen_pool_dma_alloc does not guarantee
that the resulting memory will be page-aligned. Furthermore, trying to
map slab pages (i.e., memory allocated by kmalloc) into the user space
is not resonable and can lead to problems, such as a type confusion bug
when PAGE_TABLE_CHECK=y [1].
To address these issues, this patch introduces hcd_alloc_coherent_pages,
which addresses the above two problems. Specifically,
hcd_alloc_coherent_pages uses gen_pool_dma_alloc_align instead of
gen_pool_dma_alloc to ensure that the memory is page-aligned. To replace
kmalloc, hcd_alloc_coherent_pages directly allocates pages by calling
__get_free_pages.
Reported-by: syzbot+fcf1a817ceb50935ce99@syzkaller.appspotmail.comm
Closes: https://lore.kernel.org/lkml/000000000000258e5e05fae79fc1@google.com/ [1]
Fixes: f7d34b445abc ("USB: Add support for usbfs zerocopy.")
Fixes: ff2437befd8f ("usb: host: Fix excessive alignment restriction for local memory allocations")
Cc: stable@vger.kernel.org
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230515130958.32471-2-lrh2000@pku.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices
supported and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before, and
some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different USB
drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: gadget: uvc: don't put item still in use
usb: gadget: uvc: Fix argument to sizeof() in uvc_register_video()
usb: host: ehci-exynos: switch to using gpiod API
Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"
Revert "USB: fixup for merge issue with "usb: dwc3: Don't switch OTG -> peripheral if extcon is present""
dt-bindings: usb: Convert FOTG210 to dt schema
usb: mtu3: fix failed runtime suspend in host only mode
USB: omap_udc: Fix spelling mistake: "tranceiver_ctrl" -> "transceiver_ctrl"
usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra
usb: typec: Replace custom implementation of device_match_fwnode()
usb: typec: ucsi: Don't warn on probe deferral
usb: add quirks for Lenovo OneLink+ Dock
MAINTAINERS: switch dwc3 to Thinh
usb: idmouse: fix an uninit-value in idmouse_open
USB: PHY: JZ4770: Switch to use dev_err_probe() helper
usb: phy: generic: Switch to use dev_err_probe() helper
usb: ulpi: use DEFINE_SHOW_ATTRIBUTE to simplify ulpi_regs
usb: cdns3: remove dead code
usb: cdc-wdm: Use skb_put_data() instead of skb_put/memcpy pair
usb: musb: sunxi: Switch to use dev_err_probe() helper
...
|
|
We need the USB fixes in here and this resolves the merge issue in:
drivers/usb/dwc3/gadget.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since the HC driver is now passed to the function with its
own parameter (it used to be picked from id->driver_data),
the id parameter serves no purpose.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220831125052.71584-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some platforms make use of VBUS control over PHY which means controller
driver has to access PHY registers to turn on/off VBUS line.This patch
adds support for such platforms in chipidea.
Flag 'CI_HDRC_PHY_VBUS_CONTROL' added to support VBus control feature.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20220822054051.2941282-1-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There should be no reason to adjust old ktermios which is going to get
discarded anyway.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move transition function "tcpci_to_typec_cc" to common header
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Gene Chen <gene_chen@richtek.com>
Link: https://lore.kernel.org/r/20220805071714.150882-7-gene.chen.richtek@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix incorrect pin assignment values when connecting to a monitor with
Type-C receptacle instead of a plug.
According to specification, an UFP_D receptacle's pin assignment
should came from the UFP_D pin assignments field (bit 23:16), while
an UFP_D plug's assignments are described in the DFP_D pin assignments
(bit 15:8) during Mode Discovery.
For example the LG 27 UL850-W is a monitor with Type-C receptacle.
The monitor responds to MODE DISCOVERY command with following
DisplayPort Capability flag:
dp->alt->vdo=0x140045
The existing logic only take cares of UPF_D plug case,
and would take the bit 15:8 for this 0x140045 case.
This results in an non-existing pin assignment 0x0 in
dp_altmode_configure.
To fix this problem a new set of macros are introduced
to take plug/receptacle differences into consideration.
Fixes: 0e3bb7d6894d ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Co-developed-by: Pablo Sun <pablo.sun@mediatek.com>
Co-developed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Guillaume Ranquet <granquet@baylibre.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20220804034803.19486-1-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of Thunderbolt and USB changes for 6.0-rc1.
Lots of little things here, nothing major, just constant development
on some new hardware support and cleanups of older drivers. Highlights
are:
- lots of typec changes and improvements for new hardware
- new gadget controller driver
- thunderbolt support for new hardware
- the normal set of new usb-serial device ids and cleanups
- loads of dwc3 controller fixes and improvements
- mtu3 driver updates
- testusb fixes for longtime issues (not many people use this tool it
seems.)
- minor driver fixes and improvements over the USB tree
- chromeos platform driver changes were added and then reverted as
they depened on some typec changes, but the cross-tree merges
caused problems so they will come back later through the platform
tree.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (193 commits)
usb: misc: onboard_usb_hub: Remove duplicated power_on delay
usb: misc: onboard_usb_hub: Add TI USB8041 hub support
usb: misc: onboard_usb_hub: Add reset-gpio support
USB: usbsevseg: convert sysfs snprintf to sysfs_emit
dt-bindings: usb: Add binding for TI USB8041 hub controller
ARM: multi_v7_defconfig: enable USB onboard HUB driver
ARM: dts: stm32: add support for USB2514B onboard hub on stm32mp15xx-dkx
usb: misc: onboard-hub: add support for Microchip USB2514B USB 2.0 hub
dt-bindings: usb: generic-ehci: allow usb-hcd schema properties
usb: typec: ucsi: stm32g0: add bootloader support
usb: typec: ucsi: stm32g0: add support for stm32g0 controller
dt-bindings: usb: typec: add bindings for stm32g0 controller
usb: typec: ucsi: Acknowledge the GET_ERROR_STATUS command completion
usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()
usb/chipidea: fix repeated words in comments
usb: renesas-xhci: Do not print any log while fw verif success
usb: typec: retimer: Add missing id check in match callback
USB: xhci: Fix comment typo
usb/typec/tcpm: fix repeated words in comments
usb/musb: fix repeated words in comments
...
|
|
linux/
Similarly to a recent include/net/ cleanup, this patch adds
missing includes to networking headers under include/linux.
All these problems are currently masked by the existing users
including the missing dependency before the broken header.
Link: https://lore.kernel.org/all/20220723045755.2676857-1-kuba@kernel.org/ v1
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20220726215652.158167-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Usb core introduce the mechanism of giveback of URB in tasklet context to
reduce hardware interrupt handling time. On some test situation(such as
FIO with 4KB block size), when tasklet callback function called to
giveback URB, interrupt handler add URB node to the bh->head list also.
If check bh->head list again after finish all URB giveback of local_list,
then it may introduce a "dynamic balance" between giveback URB and add URB
to bh->head list. This tasklet callback function may not exit for a long
time, which will cause other tasklet function calls to be delayed. Some
real-time applications(such as KB and Mouse) will see noticeable lag.
In order to prevent the tasklet function from occupying the cpu for a long
time at a time, new URBS will not be added to the local_list even though
the bh->head list is not empty. But also need to ensure the left URB
giveback to be processed in time, so add a member high_prio for structure
giveback_urb_bh to prioritize tasklet and schelule this tasklet again if
bh->head list is not empty.
At the same time, we are able to prioritize tasklet through structure
member high_prio. So, replace the local high_prio_bh variable with this
structure member in usb_hcd_giveback_urb.
Fixes: 94dfd7edfd5c ("USB: HCD: support giveback of URB in tasklet context")
Cc: stable <stable@kernel.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20220726074918.5114-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DisplayLink ethernet devices require NTB buffers larger then 32kb
in order to run with highest performance.
This patch is changing upper limit of the rx and tx buffers.
Those buffers are initialized with CDC_NCM_NTB_DEF_SIZE_RX and
CDC_NCM_NTB_DEF_SIZE_TX which is 16kb so by default no device is
affected by increased limit.
Rx and tx buffer is increased under two conditions:
- Device need to advertise that it supports higher buffer size in
dwNtbMaxInMaxSize and dwNtbMaxOutMaxSize.
- cdc_ncm/rx_max and cdc_ncm/tx_max driver parameters must be adjusted
with udev rule or ethtool.
Summary of testing and performance results:
Tests were performed on following devices:
- DisplayLink DL-3xxx family device
- DisplayLink DL-6xxx family device
- ASUS USB-C2500 2.5G USB3 ethernet adapter
- Plugable USB3 1G USB3 ethernet adapter
- EDIMAX EU-4307 USB-C ethernet adapter
- Dell DBQBCBC064 USB-C ethernet adapter
Performance measurements were done with:
- iperf3 between two linux boxes
- http://openspeedtest.com/ instance running on local test machine
Insights from tests results:
- All except one from third party usb adapters were not affected by
increased buffer size to their advertised dwNtbOutMaxSize and
dwNtbInMaxSize.
Devices were generally reaching 912-940Mbps both download and upload.
Only EDIMAX adapter experienced decreased download size from
929Mbps to 827Mbps with iper3, with openspeedtest decrease was from
968Mbps to 886Mbps.
- DisplayLink DL-3xxx family devices experienced performance increase
with iperf3 download from 300Mbps to 870Mbps and
upload from 782Mbps to 844Mbps.
With openspeedtest download increased from 556Mbps to 873Mbps
and upload from 727Mbps to 973Mbps
- DiplayLink DL-6xxx family devices are not affected by
increased buffer size.
Signed-off-by: Łukasz Spintzyk <lukasz.spintzyk@synaptics.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220720060518.541-2-lukasz.spintzyk@synaptics.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce a retimer device class and associated functions that register
and use retimer "switch" devices. These operate in a manner similar to
the "mode-switch" and help configure retimers that exist between the
Type-C connector and host controller(s).
Type C ports can be linked to retimers using firmware node device
references (again, in a manner similar to "mode-switch").
There are no new sysfs files being created; there is the new retimer
class directory, but there are no class-specific files being created
there.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220711072333.2064341-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220630123445.v24.3.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB PD controllers which consisting of a microcontroller (acting as the TCPM)
and a port controller (TCPC) - may require that the driver for the PD
controller accesses directly also the on-chip port controller in some cases.
Move tcpci.h to include/linux/usb/ is convenience access TCPC registers.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Link: https://lore.kernel.org/r/20220706083433.2415524-1-xji@analogixsemi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Without that, the parameter is not properly parsed:
include/linux/usb/typec_altmode.h:132: warning: Function parameter or member 'altmode' not described in 'typec_altmode_get_orientation'
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/70dc4c5d744cf1fe9a0efe6b85deaa0489628282.1656409369.git.mchehab@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are some drivers that can use the Type C mux API, but don't have
to. Introduce CONFIG guards for the mux functions so that drivers can
include the header file and not run into compilation errors on systems
which don't have CONFIG_TYPEC enabled. When CONFIG_TYPEC is not enabled,
the Type C mux functions will be stub versions of the original calls.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20220615172129.1314056-3-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All the USB Type-C Connector Class devices are protected, so
the drivers can not directly access them. This will adds a
few helpers that can be used to link the ports and partners
to the correct USB Power Delivery objects.
For ports a new optional sysfs attribute file is also added
that can be used to select the USB Power Delivery
capabilities that the port will advertise to the partner.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220502132058.86236-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introducing a small device class for USB Power Delivery.
The idea with it is that we do not mix any more USB Power
Delivery information into the USB Type-C connectors only.
This separation will make it possible to register USB Power
Delivery devices also from other places, for example from
USB Type-C Bridges (see USB Type-C Bridge Specification).
The device class will not always deal with only the messages
and objects that were negotiated with the partner, but
instead messages and objects that can be used in the
negotiation. That allows the USB PD devices to be shared and
reconfigured. The ports can decide which objects are to be
advertised to the partner before the contract is negotiated.
It is also possible to allow the user space to make that
decision if needed.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220502132058.86236-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
comments
All these files have been updated in the commit given in the Fixes: tag
below.
When the SPDX-License-Identifier: has been added, the corresponding text at
the beginning of the files has not been deleted.
All these texts are about GPL-2.0+, with different variation in the
wording.
Remove these now useless lines to save some LoC.
Fixes: 5fd54ace4721 ("USB: add SPDX identifiers to all remaining files in drivers/usb/")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All these files have been updated in the commit given in the Fixes: tag
below.
When the SPDX-License-Identifier: has been added, the corresponding text at
the beginning of the files has not been deleted.
All these texts are about GPL-2.0, with different variation in the wording.
Remove these now useless lines to save some LoC.
Fixes: 5fd54ace4721 ("USB: add SPDX identifiers to all remaining files in drivers/usb/")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
|
|
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26ee ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0
race")
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220510091630.16564-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Putting USB gadgets on a new bus of their own encounters a problem
when multiple gadgets are present: They all have the same name! The
driver core fails with a "sys: cannot create duplicate filename" error
when creating any of the /sys/bus/gadget/devices/<gadget-name>
symbolic links after the first.
This patch fixes the problem by adding a ".N" suffix to each gadget's
name when the gadget is registered (where N is a unique ID number),
thus making the names distinct.
Reported-and-tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: fc274c1e9973 ("USB: gadget: Add a new bus for gadgets")
Link: https://lore.kernel.org/r/YnqKAXKyp9Vq/pbn@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tools/testing/selftests/net/forwarding/Makefile
f62c5acc800e ("selftests/net/forwarding: add missing tests to Makefile")
50fe062c806e ("selftests: forwarding: new test, verify host mdb entries")
https://lore.kernel.org/all/20220502111539.0b7e4621@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 0298b4b95cb373c21e6323c905589f8dac42c5b4.
The series still has built errors as reported in linux-next, so revert
it for now.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20220502210728.0b36f3cd@canb.auug.org.au
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit c40b62216c1aecc0dc00faf33d71bd71cb440337.
The series still has built errors as reported in linux-next, so revert
it for now.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20220502210728.0b36f3cd@canb.auug.org.au
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Call onboard_hub_create/destroy_pdevs() from usb_add/remove_hcd()
for primary HCDs to create/destroy platform devices for onboard
USB hubs that may be connected to the root hub of the controller.
These functions are a NOP unless CONFIG_USB_ONBOARD_HUB=y/m.
Also add a field to struct usb_hcd to keep track of the onboard hub
platform devices that are owned by the HCD.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220217104219.v21.3.I7a3a7d9d2126c34079b1cab87aa0b2ec3030f9b7@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Note: the current series only supports hubs connected directly to
a root hub, support for other configurations could be added if
needed.
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220217104219.v21.2.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds a "gadget" bus and uses it for registering gadgets and
their drivers. From now on, bindings will be managed by the driver
core rather than through ad-hoc manipulations in the UDC core.
As part of this change, the driver_pending_list is removed. The UDC
core won't need to keep track of unbound drivers for later binding,
because the driver core handles all of that for us.
However, we do need one new feature: a way to prevent gadget drivers
from being bound to more than one gadget at a time. The existing code
does this automatically, but the driver core doesn't -- it's perfectly
happy to bind a single driver to all the matching devices on the bus.
The patch adds a new bitflag to the usb_gadget_driver structure for
this purpose.
A nice side effect of this change is a reduction in the total lines of
code, since now the driver core will do part of the work that the UDC
used to do.
A possible future patch could add udc devices to the gadget bus, say
as a separate device type.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YmSpdxaDNeC2BBOf@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In preparation for adding a "gadget" bus, this patch renames
usb_gadget_probe_driver() to usb_gadget_register_driver(). The new
name will be more accurate, since gadget drivers will be registered on
the gadget bus and the probing will be done by the driver core, not
the UDC core.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YmSc29YZvxgT5fEJ@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rather than directly exposing the implementation's representation of the
typec muxes to the controller/clients, introduce an indirection object.
This enables the introduction of turning this relationship into a
one-to-many in the following patch.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220422222351.1297276-5-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
