| Age | Commit message (Collapse) | Author |
|---|
|
commit 4b50bcc7eda4d3cc9e3f2a0aa60e590fedf728c5 upstream.
Since commit 92923ca3aace ("mm: meminit: only set page reserved in the
memblock region") the reserved bit is set on reserved memblock regions.
However start and end address are passed as unsigned long. This is only
32bit on i386, so it can end up marking the wrong pages reserved for
ranges at 4GB and above.
This was observed on a 32bit Xen dom0 which was booted with initial
memory set to a value below 4G but allowing to balloon in memory
(dom0_mem=1024M for example). This would define a reserved bootmem
region for the additional memory (for example on a 8GB system there was
a reverved region covering the 4GB-8GB range). But since the addresses
were passed on as unsigned long, this was actually marking all pages
from 0 to 4GB as reserved.
Fixes: 92923ca3aacef63 ("mm: meminit: only set page reserved in the memblock region")
Link: http://lkml.kernel.org/r/1463491221-10573-1-git-send-email-stefan.bader@canonical.com
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca9eb49aa9562eaadf3cea071ec7018ad6800425 upstream.
The generic copy_siginfo() is currently defined in
asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which
defines the generic struct siginfo. However this makes it awkward for an
architecture to use it if it has to define its own struct siginfo (e.g.
MIPS and potentially IA64), since it means that asm-generic/siginfo.h
can only be included after defining the arch-specific siginfo, which may
be problematic if the arch-specific definition needs definitions from
uapi/asm-generic/siginfo.h.
It is possible to work around this by first including
uapi/asm-generic/siginfo.h to get the constants before defining the
arch-specific siginfo, and include asm-generic/siginfo.h after. However
uapi headers can't be included by other uapi headers, so that first
include has to be in an ifdef __kernel__, with the non __kernel__ case
including the non-UAPI header instead.
Instead of that mess, move the generic copy_siginfo() definition into
linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to
include asm-generic/siginfo.h and define the arch-specific siginfo, and
for the generic copy_siginfo() to see that arch-specific definition.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Petr Malat <oss@malat.biz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Christopher Ferris <cferris@google.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12478/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0f40fbbcc34e093255a2b2d70b6b0fb48c3f39aa upstream.
OpenSSH expects the (non-blocking) read() of pty master to return
EAGAIN only if it has received all of the slave-side output after
it has received SIGCHLD. This used to work on pre-3.12 kernels.
This fix effectively forces non-blocking read() and poll() to
block for parallel i/o to complete for all ttys. It also unwinds
these changes:
1) f8747d4a466ab2cafe56112c51b3379f9fdb7a12
tty: Fix pty master read() after slave closes
2) 52bce7f8d4fc633c9a9d0646eef58ba6ae9a3b73
pty, n_tty: Simplify input processing on final close
3) 1a48632ffed61352a7810ce089dc5a8bcd505a60
pty: Fix input race when closing
Inspired by analysis and patch from Marc Aurele La France <tsi@tuyoix.net>
Reported-by: Volth <openssh@volth.com>
Reported-by: Marc Aurele La France <tsi@tuyoix.net>
BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=52
BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=2492
Signed-off-by: Brian Bloniarz <brian.bloniarz@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6fb650d43da3e7054984dc548eaa88765a94d49f upstream.
When a USB driver is bound to an interface (either through probing or
by claiming it) or is unbound from an interface, the USB core always
disables Link Power Management during the transition and then
re-enables it afterward. The reason is because the driver might want
to prevent hub-initiated link power transitions, in which case the HCD
would have to recalculate the various LPM parameters. This
recalculation takes place when LPM is re-enabled and the new
parameters are sent to the device and its parent hub.
However, if the driver does not want to prevent hub-initiated link
power transitions then none of this work is necessary. The parameters
don't need to be recalculated, and LPM doesn't need to be disabled and
re-enabled.
It turns out that disabling and enabling LPM can be time-consuming,
enough so that it interferes with user programs that want to claim and
release interfaces rapidly via usbfs. Since the usbfs kernel driver
doesn't set the disable_hub_initiated_lpm flag, we can speed things up
and get the user programs to work by leaving LPM alone whenever the
flag isn't set.
And while we're improving the way disable_hub_initiated_lpm gets used,
let's also fix its kerneldoc.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Matthew Giassa <matthew@giassa.net>
CC: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bb208f144cf3f59d8f89a09a80efd04389718907 upstream.
As described in 'can: m_can: tag current CAN FD controllers as non-ISO'
(6cfda7fbebe) it is possible to define fixed configuration options by
setting the according bit in 'ctrlmode' and clear it in 'ctrlmode_supported'.
This leads to the incovenience that the fixed configuration bits can not be
passed by netlink even when they have the correct values (e.g. non-ISO, FD).
This patch fixes that issue and not only allows fixed set bit values to be set
again but now requires(!) to provide these fixed values at configuration time.
A valid CAN FD configuration consists of a nominal/arbitration bittiming, a
data bittiming and a control mode with CAN_CTRLMODE_FD set - which is now
enforced by a new can_validate() function. This fix additionally removed the
inconsistency that was prohibiting the support of 'CANFD-only' controller
drivers, like the RCar CAN FD.
For this reason a new helper can_set_static_ctrlmode() has been introduced to
provide a proper interface to handle static enabled CAN controller options.
Reported-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Reviewed-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3b672623079bb3e5685b8549e514f2dfaa564406 upstream.
The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff
instead of 0x1f) thus reading entire register as buck9's voltage. This
effectively caused regulator core to interpret values as higher voltages
than they were and then to set real voltage much lower than intended.
The buck9 provides power to other regulators, including LDO13
and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower
voltage caused SD card detection errors on Odroid XU3/XU4:
mmc1: card never left busy state
mmc1: error -110 whilst initialising SD card
During driver probe the regulator core was checking whether initial
voltage matches the constraints. With incorrect vsel_mask of 0xff and
default value of 0x50, the core interpreted this as 5 V which is outside
of constraints (3-3.775 V). Then the regulator core was adjusting the
voltage to match the constraints. With incorrect vsel_mask this new
voltage mapped to a vere low voltage in the driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 54d5ca871e72f2bb172ec9323497f01cd5091ec7 upstream.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d0a07edd17cfc12fdc1f36de8072fa17cc3666f upstream.
This will provide fully accuracy to the mapcount calculation in the
write protect faults, so page pinning will not get broken by false
positive copy-on-writes.
total_mapcount() isn't the right calculation needed in
reuse_swap_page(), so this introduces a page_trans_huge_mapcount()
that is effectively the full accurate return value for page_mapcount()
if dealing with Transparent Hugepages, however we only use the
page_trans_huge_mapcount() during COW faults where it strictly needed,
due to its higher runtime cost.
This also provide at practical zero cost the total_mapcount
information which is needed to know if we can still relocate the page
anon_vma to the local vma. If page_trans_huge_mapcount() returns 1 we
can reuse the page no matter if it's a pte or a pmd_trans_huge
triggering the fault, but we can only relocate the page anon_vma to
the local vma->anon_vma if we're sure it's only this "vma" mapping the
whole THP physical range.
Kirill A. Shutemov discovered the problem with moving the page
anon_vma to the local vma->anon_vma in a previous version of this
patch and another problem in the way page_move_anon_rmap() was called.
Andrew Morton discovered that CONFIG_SWAP=n wouldn't build in a
previous version, because reuse_swap_page must be a macro to call
page_trans_huge_mapcount from swap.h, so this uses a macro again
instead of an inline function. With this change at least it's a less
dangerous usage than it was before, because "page" is used only once
now, while with the previous code reuse_swap_page(page++) would have
called page_mapcount on page+1 and it would have increased page twice
instead of just once.
Dean Luick noticed an uninitialized variable that could result in a
rmap inefficiency for the non-THP case in a previous version.
Mike Marciniszyn said:
: Our RDMA tests are seeing an issue with memory locking that bisects to
: commit 61f5d698cc97 ("mm: re-enable THP")
:
: The test program registers two rather large MRs (512M) and RDMA
: writes data to a passive peer using the first and RDMA reads it back
: into the second MR and compares that data. The sizes are chosen randomly
: between 0 and 1024 bytes.
:
: The test will get through a few (<= 4 iterations) and then gets a
: compare error.
:
: Tracing indicates the kernel logical addresses associated with the individual
: pages at registration ARE correct , the data in the "RDMA read response only"
: packets ARE correct.
:
: The "corruption" occurs when the packet crosse two pages that are not physically
: contiguous. The second page reads back as zero in the program.
:
: It looks like the user VA at the point of the compare error no longer points to
: the same physical address as was registered.
:
: This patch totally resolves the issue!
Link: http://lkml.kernel.org/r/1462547040-1737-2-git-send-email-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: "Kirill A. Shutemov" <kirill@shutemov.name>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Tested-by: Josh Collier <josh.d.collier@intel.com>
Cc: Marc Haber <mh+linux-kernel@zugschlus.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2c94b53738549d81dc7464a32117d1f5112c64d3 ]
Prior to commit d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op
when !DEBUG") the implementation of net_dbg_ratelimited() was buggy
for both the DEBUG and CONFIG_DYNAMIC_DEBUG cases.
The bug was that net_ratelimit() was being called and, despite
returning true, nothing was being printed to the console. This
resulted in messages like the following -
"net_ratelimit: %d callbacks suppressed"
with no other output nearby.
After commit d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when
!DEBUG") the bug is fixed for the DEBUG case. However, there's no
output at all for CONFIG_DYNAMIC_DEBUG case.
This patch restores debug output (if enabled) for the
CONFIG_DYNAMIC_DEBUG case.
Add a definition of net_dbg_ratelimited() for the CONFIG_DYNAMIC_DEBUG
case. The implementation takes care to check that dynamic debugging is
enabled before calling net_ratelimit().
Fixes: d92cff89a0c8 ("net_dbg_ratelimited: turn into no-op when !DEBUG")
Signed-off-by: Tim Bingham <tbingham@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 92117d8443bc5afacc8d5ba82e541946310f106e ]
On a system with >32Gbyte of phyiscal memory and infinite RLIMIT_MEMLOCK,
the malicious application may overflow 32-bit bpf program refcnt.
It's also possible to overflow map refcnt on 1Tb system.
Impose 32k hard limit which means that the same bpf program or
map cannot be shared by more than 32k processes.
Fixes: 1be7f75d1668 ("bpf: enable non-root eBPF programs")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cd255efff9baadd654d6160e52d17ae7c568c9d3 ]
Set and report vport MTU rather than physical MTU,
Driver will set both vport and physical port mtu and will
rely on the query of vport mtu.
SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.
Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 046339eaab26804f52f6604877f5674f70815b26 ]
For set/query MTU port firmware commands the MTU field
is 16 bits, here I changed all the "int mtu" parameters
of the functions wrapping those firmware commands to be u16.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d894ba18d4e449b3a7f6eb491f16c9e02933736e ]
With the SO_REUSEPORT socket option, it is possible to create sockets
in the AF_INET and AF_INET6 domains which are bound to the same IPv4 address.
This is only possible with SO_REUSEPORT and when not using IPV6_V6ONLY on
the AF_INET6 sockets.
Prior to the commits referenced below, an incoming IPv4 packet would
always be routed to a socket of type AF_INET when this mixed-mode was used.
After those changes, the same packet would be routed to the most recently
bound socket (if this happened to be an AF_INET6 socket, it would
have an IPv4 mapped IPv6 address).
The change in behavior occurred because the recent SO_REUSEPORT optimizations
short-circuit the socket scoring logic as soon as they find a match. They
did not take into account the scoring logic that favors AF_INET sockets
over AF_INET6 sockets in the event of a tie.
To fix this problem, this patch changes the insertion order of AF_INET
and AF_INET6 addresses in the TCP and UDP socket lists when the sockets
have SO_REUSEPORT set. AF_INET sockets will be inserted at the head of the
list and AF_INET6 sockets with SO_REUSEPORT set will always be inserted at
the tail of the list. This will force AF_INET sockets to always be
considered first.
Fixes: e32ea7e74727 ("soreuseport: fast reuseport UDP socket selection")
Fixes: 125e80b88687 ("soreuseport: fast reuseport TCP socket selection")
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4550c4e157ca3da929593bb6c64080a59141af35 upstream.
Cgroup2 currently doesn't have a per-cgroup swappiness setting. We
might want to add one later - that's a different discussion - but until
we do, the cgroups should always follow the system setting. Otherwise
it will be unchangeably set to whatever the ancestor inherited from the
system setting at the time of cgroup creation.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 689de1d6ca95b3b5bd8ee446863bf81a4883ea25 upstream.
This is a fairly minimal fixup to the horribly bad behavior of hash_64()
with certain input patterns.
In particular, because the multiplicative value used for the 64-bit hash
was intentionally bit-sparse (so that the multiply could be done with
shifts and adds on architectures without hardware multipliers), some
bits did not get spread out very much. In particular, certain fairly
common bit ranges in the input (roughly bits 12-20: commonly with the
most information in them when you hash things like byte offsets in files
or memory that have block factors that mean that the low bits are often
zero) would not necessarily show up much in the result.
There's a bigger patch-series brewing to fix up things more completely,
but this is the fairly minimal fix for the 64-bit hashing problem. It
simply picks a much better constant multiplier, spreading the bits out a
lot better.
NOTE! For 32-bit architectures, the bad old hash_64() remains the same
for now, since 64-bit multiplies are expensive. The bigger hashing
cleanup will replace the 32-bit case with something better.
The new constants were picked by George Spelvin who wrote that bigger
cleanup series. I just picked out the constants and part of the comment
from that series.
Cc: George Spelvin <linux@horizon.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 50359819794b4a16ae35051cd80f2dab025f6019 upstream.
Commit e6d5e7d90be9 ("clk-divider: Fix READ_ONLY when divider > 1") removed
the special ops struct for read-only clocks and instead opted to handle
them inside the regular ops.
On the rk3368 this results in breakage as aclkm now gets set a value.
While it is the same divider value, the A53 core still doesn't like it,
which can result in the cpu ending up in a hang.
The reason being that "ACLKENMasserts one clock cycle before the rising
edge of ACLKM" and the clock should only be touched when STANDBYWFIL2
is asserted.
To fix this, reintroduce the read-only ops but do include the round_rate
callback. That way no writes that may be unsafe are done to the divider
register in any case.
The Rockchip use of the clk_divider_ops is adapted to this split again,
as is the nxp, lpc18xx-ccu driver that was included since the original
commit. On lpc18xx-ccu the divider seems to always be read-only
so only uses the new ops now.
Fixes: e6d5e7d90be9 ("clk-divider: Fix READ_ONLY when divider > 1")
Reported-by: Zhang Qing <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c283e41ef32442f41e7180f9bb1c5aedf9255bfe upstream.
The DMA chip has a fixed number of requestor lines used for flow
control. This number is platform dependent. The pxa_dma dma driver will
use this value to activate or not the flow control.
There won't be any impact on mmp_pdma driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 28093f9f34cedeaea0f481c58446d9dac6dd620f upstream.
In gather_pte_stats() a THP pmd is cast into a pte, which is wrong
because the layouts may differ depending on the architecture. On s390
this will lead to inaccurate numa_maps accounting in /proc because of
misguided pte_present() and pte_dirty() checks on the fake pte.
On other architectures pte_present() and pte_dirty() may work by chance,
but there may be an issue with direct-access (dax) mappings w/o
underlying struct pages when HAVE_PTE_SPECIAL is set and THP is
available. In vm_normal_page() the fake pte will be checked with
pte_special() and because there is no "special" bit in a pmd, this will
always return false and the VM_PFNMAP | VM_MIXEDMAP checking will be
skipped. On dax mappings w/o struct pages, an invalid struct page
pointer would then be returned that can crash the kernel.
This patch fixes the numa_maps THP handling by introducing new "_pmd"
variants of the can_gather_numa_stats() and vm_normal_page() functions.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66ee95d16a7f1b7b4f1dd74a2d81c6e19dc29a14 upstream.
HugeTLB pages cannot be split, so we use the compound_mapcount to track
rmaps.
Currently page_mapped() will check the compound_mapcount, but will also
go through the constituent pages of a THP compound page and query the
individual _mapcount's too.
Unfortunately, page_mapped() does not distinguish between HugeTLB and
THP compound pages and assumes that a compound page always needs to have
HPAGE_PMD_NR pages querying.
For most cases when dealing with HugeTLB this is just inefficient, but
for scenarios where the HugeTLB page size is less than the pmd block
size (e.g. when using contiguous bit on ARM) this can lead to crashes.
This patch adjusts the page_mapped function such that we skip the
unnecessary THP reference checks for HugeTLB pages.
Fixes: e1534ae95004 ("mm: differentiate page_mapped() from page_mapcount() for compound pages")
Signed-off-by: Steve Capper <steve.capper@arm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cgroup_subsys->post_attach callback
commit 5cf1cacb49aee39c3e02ae87068fc3c6430659b0 upstream.
Since e93ad19d0564 ("cpuset: make mm migration asynchronous"), cpuset
kicks off asynchronous NUMA node migration if necessary during task
migration and flushes it from cpuset_post_attach_flush() which is
called at the end of __cgroup_procs_write(). This is to avoid
performing migration with cgroup_threadgroup_rwsem write-locked which
can lead to deadlock through dependency on kworker creation.
memcg has a similar issue with charge moving, so let's convert it to
an official callback rather than the current one-off cpuset specific
function. This patch adds cgroup_subsys->post_attach callback and
makes cpuset register cpuset_post_attach_flush() as its ->post_attach.
The conversion is mostly one-to-one except that the new callback is
called under cgroup_mutex. This is to guarantee that no other
migration operations are started before ->post_attach callbacks are
finished. cgroup_mutex is one of the outermost mutex in the system
and has never been and shouldn't be a problem. We can add specialized
synchronization around __cgroup_procs_write() but I don't think
there's any noticeable benefit.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 986ef95ecdd3eb6fa29433e68faa94c7624083be upstream.
mlx5 devices (Connect-IB, ConnectX-4, ConnectX-4-LX) has a limitation
where rdma read work queue entries cannot exceed 512 bytes.
A rdma_read wqe needs to fit in 512 bytes:
- wqe control segment (16 bytes)
- rdma segment (16 bytes)
- scatter elements (16 bytes each)
So max_sge_rd should be: (512 - 16 - 16) / 16 = 30.
Reported-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagig@grimberg.me>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d101a125954eae1d397adda94ca6319485a50493 upstream.
This series fixes bugs in nfs and ext4 due to 4bacc9c9234c ("overlayfs:
Make f_path always point to the overlay and f_inode to the underlay").
Regular files opened on overlayfs will result in the file being opened on
the underlying filesystem, while f_path points to the overlayfs
mount/dentry.
This confuses filesystems which get the dentry from struct file and assume
it's theirs.
Add a new helper, file_dentry() [*], to get the filesystem's own dentry
from the file. This checks file->f_path.dentry->d_flags against
DCACHE_OP_REAL, and returns file->f_path.dentry if DCACHE_OP_REAL is not
set (this is the common, non-overlayfs case).
In the uncommon case it will call into overlayfs's ->d_real() to get the
underlying dentry, matching file_inode(file).
The reason we need to check against the inode is that if the file is copied
up while being open, d_real() would return the upper dentry, while the open
file comes from the lower dentry.
[*] If possible, it's better simply to use file_inode() instead.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Tested-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1363074667a6b7d0507527742ccd7bbed5e3ceaa upstream.
Add a new NO_REPORT_LUNS quirk and set it for Seagate drives with
an usb-id of: 0bc2:331a, as these will fail to respond to a
REPORT_LUNS command.
Reported-and-tested-by: David Webb <djw@noc.ac.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5a5abb1fa3b05dd6aa821525832644c1e7d2905f ]
Sasha Levin reported a suspicious rcu_dereference_protected() warning
found while fuzzing with trinity that is similar to this one:
[ 52.765684] net/core/filter.c:2262 suspicious rcu_dereference_protected() usage!
[ 52.765688] other info that might help us debug this:
[ 52.765695] rcu_scheduler_active = 1, debug_locks = 1
[ 52.765701] 1 lock held by a.out/1525:
[ 52.765704] #0: (rtnl_mutex){+.+.+.}, at: [<ffffffff816a64b7>] rtnl_lock+0x17/0x20
[ 52.765721] stack backtrace:
[ 52.765728] CPU: 1 PID: 1525 Comm: a.out Not tainted 4.5.0+ #264
[...]
[ 52.765768] Call Trace:
[ 52.765775] [<ffffffff813e488d>] dump_stack+0x85/0xc8
[ 52.765784] [<ffffffff810f2fa5>] lockdep_rcu_suspicious+0xd5/0x110
[ 52.765792] [<ffffffff816afdc2>] sk_detach_filter+0x82/0x90
[ 52.765801] [<ffffffffa0883425>] tun_detach_filter+0x35/0x90 [tun]
[ 52.765810] [<ffffffffa0884ed4>] __tun_chr_ioctl+0x354/0x1130 [tun]
[ 52.765818] [<ffffffff8136fed0>] ? selinux_file_ioctl+0x130/0x210
[ 52.765827] [<ffffffffa0885ce3>] tun_chr_ioctl+0x13/0x20 [tun]
[ 52.765834] [<ffffffff81260ea6>] do_vfs_ioctl+0x96/0x690
[ 52.765843] [<ffffffff81364af3>] ? security_file_ioctl+0x43/0x60
[ 52.765850] [<ffffffff81261519>] SyS_ioctl+0x79/0x90
[ 52.765858] [<ffffffff81003ba2>] do_syscall_64+0x62/0x140
[ 52.765866] [<ffffffff817d563f>] entry_SYSCALL64_slow_path+0x25/0x25
Same can be triggered with PROVE_RCU (+ PROVE_RCU_REPEATEDLY) enabled
from tun_attach_filter() when user space calls ioctl(tun_fd, TUN{ATTACH,
DETACH}FILTER, ...) for adding/removing a BPF filter on tap devices.
Since the fix in f91ff5b9ff52 ("net: sk_{detach|attach}_filter() rcu
fixes") sk_attach_filter()/sk_detach_filter() now dereferences the
filter with rcu_dereference_protected(), checking whether socket lock
is held in control path.
Since its introduction in 994051625981 ("tun: socket filter support"),
tap filters are managed under RTNL lock from __tun_chr_ioctl(). Thus the
sock_owned_by_user(sk) doesn't apply in this specific case and therefore
triggers the false positive.
Extend the BPF API with __sk_attach_filter()/__sk_detach_filter() pair
that is used by tap filters and pass in lockdep_rtnl_is_held() for the
rcu_dereference_protected() checks instead.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4c656c13b254d598e83e586b7b4d36a2043dad85 ]
This fixes a regression in the bridge ageing time caused by:
commit c62987bbd8a1 ("bridge: push bridge setting ageing_time down to switchdev")
There are users of Linux bridge which use the feature that if ageing time
is set to 0 it causes entries to never expire. See:
https://www.linuxfoundation.org/collaborate/workgroups/networking/bridge
For a pure software bridge, it is unnecessary for the code to have
arbitrary restrictions on what values are allowable.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2793a23aacbd754dbbb5cb75093deb7e4103bace ]
Netdevice parameter hard_header_len is variously interpreted both as
an upper and lower bound on link layer header length. The field is
used as upper bound when reserving room at allocation, as lower bound
when validating user input in PF_PACKET.
Clarify the definition to be maximum header length. For validation
of untrusted headers, add an optional validate member to header_ops.
Allow bypassing of validation by passing CAP_SYS_RAWIO, for instance
for deliberate testing of corrupt input. In this case, pad trailing
bytes, as some device drivers expect completely initialized headers.
See also http://comments.gmane.org/gmane.linux.network/401064
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 95272c29378ee7dc15f43fa2758cb28a5913a06d upstream.
-ftracer can duplicate asm blocks causing compilation to fail in
noclone functions. For example, KVM declares a global variable
in an asm like
asm("2: ... \n
.pushsection data \n
.global vmx_return \n
vmx_return: .long 2b");
and -ftracer causes a double declaration.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: kvm@vger.kernel.org
Reported-by: Linda Walsh <lkml@tlinx.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3debb0a9ddb16526de8b456491b7db60114f7b5e upstream.
The trace_printk() code will allocate extra buffers if the compile detects
that a trace_printk() is used. To do this, the format of the trace_printk()
is saved to the __trace_printk_fmt section, and if that section is bigger
than zero, the buffers are allocated (along with a message that this has
happened).
If trace_printk() uses a format that is not a constant, and thus something
not guaranteed to be around when the print happens, the compiler optimizes
the fmt out, as it is not used, and the __trace_printk_fmt section is not
filled. This means the kernel will not allocate the special buffers needed
for the trace_printk() and the trace_printk() will not write anything to the
tracing buffer.
Adding a "__used" to the variable in the __trace_printk_fmt section will
keep it around, even though it is set to NULL. This will keep the string
from being printed in the debugfs/tracing/printk_formats section as it is
not needed.
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Fixes: 07d777fe8c398 "tracing: Add percpu buffers for trace_printk()"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 378c6520e7d29280f400ef2ceaf155c86f05a71a upstream.
This commit fixes the following security hole affecting systems where
all of the following conditions are fulfilled:
- The fs.suid_dumpable sysctl is set to 2.
- The kernel.core_pattern sysctl's value starts with "/". (Systems
where kernel.core_pattern starts with "|/" are not affected.)
- Unprivileged user namespace creation is permitted. (This is
true on Linux >=3.8, but some distributions disallow it by
default using a distro patch.)
Under these conditions, if a program executes under secure exec rules,
causing it to run with the SUID_DUMP_ROOT flag, then unshares its user
namespace, changes its root directory and crashes, the coredump will be
written using fsuid=0 and a path derived from kernel.core_pattern - but
this path is interpreted relative to the root directory of the process,
allowing the attacker to control where a coredump will be written with
root privileges.
To fix the security issue, always interpret core_pattern for dumps that
are written under SUID_DUMP_ROOT relative to the root directory of init.
Signed-off-by: Jann Horn <jann@thejh.net>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2b021cbf3cb6208f0d40fd2f1869f237934340ed upstream.
Before 2e91fa7f6d45 ("cgroup: keep zombies associated with their
original cgroups"), all dead tasks were associated with init_css_set.
If a zombie task is requested for migration, while migration prep
operations would still be performed on init_css_set, the actual
migration would ignore zombie tasks. As init_css_set is always valid,
this worked fine.
However, after 2e91fa7f6d45, zombie tasks stay with the css_set it was
associated with at the time of death. Let's say a task T associated
with cgroup A on hierarchy H-1 and cgroup B on hiearchy H-2. After T
becomes a zombie, it would still remain associated with A and B. If A
only contains zombie tasks, it can be removed. On removal, A gets
marked offline but stays pinned until all zombies are drained. At
this point, if migration is initiated on T to a cgroup C on hierarchy
H-2, migration path would try to prepare T's css_set for migration and
trigger the following.
WARNING: CPU: 0 PID: 1576 at kernel/cgroup.c:474 cgroup_get+0x121/0x160()
CPU: 0 PID: 1576 Comm: bash Not tainted 4.4.0-work+ #289
...
Call Trace:
[<ffffffff8127e63c>] dump_stack+0x4e/0x82
[<ffffffff810445e8>] warn_slowpath_common+0x78/0xb0
[<ffffffff810446d5>] warn_slowpath_null+0x15/0x20
[<ffffffff810c33e1>] cgroup_get+0x121/0x160
[<ffffffff810c349b>] link_css_set+0x7b/0x90
[<ffffffff810c4fbc>] find_css_set+0x3bc/0x5e0
[<ffffffff810c5269>] cgroup_migrate_prepare_dst+0x89/0x1f0
[<ffffffff810c7547>] cgroup_attach_task+0x157/0x230
[<ffffffff810c7a17>] __cgroup_procs_write+0x2b7/0x470
[<ffffffff810c7bdc>] cgroup_tasks_write+0xc/0x10
[<ffffffff810c4790>] cgroup_file_write+0x30/0x1b0
[<ffffffff811c68fc>] kernfs_fop_write+0x13c/0x180
[<ffffffff81151673>] __vfs_write+0x23/0xe0
[<ffffffff81152494>] vfs_write+0xa4/0x1a0
[<ffffffff811532d4>] SyS_write+0x44/0xa0
[<ffffffff814af2d7>] entry_SYSCALL_64_fastpath+0x12/0x6f
It doesn't make sense to prepare migration for css_sets pointing to
dead cgroups as they are guaranteed to contain only zombies which are
ignored later during migration. This patch makes cgroup destruction
path mark all affected css_sets as dead and updates the migration path
to ignore them during preparation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 2e91fa7f6d45 ("cgroup: keep zombies associated with their original cgroups")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f33798deecbd59a2955f40ac0ae2bc7dff54c069 upstream.
commit 9ce119f318ba ("tty: Fix GPF in flush_to_ldisc()") fixed a
GPF caused by a line discipline which does not define a receive_buf()
method.
However, the vt driver (and speakup driver also) pushes selection
data directly to the line discipline receive_buf() method via
tty_ldisc_receive_buf(). Fix the same problem in tty_ldisc_receive_buf().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4df2bf466a9c9c92f40d27c4aa9120f4e8227bfc upstream.
Otherwise loading a "snapshot" table using the same device for the
origin and COW devices, e.g.:
echo "0 20971520 snapshot 253:3 253:3 P 8" | dmsetup create snap
will trigger:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000098
[ 1958.979934] IP: [<ffffffffa040efba>] dm_exception_store_set_chunk_size+0x7a/0x110 [dm_snapshot]
[ 1958.989655] PGD 0
[ 1958.991903] Oops: 0000 [#1] SMP
...
[ 1959.059647] CPU: 9 PID: 3556 Comm: dmsetup Tainted: G IO 4.5.0-rc5.snitm+ #150
...
[ 1959.083517] task: ffff8800b9660c80 ti: ffff88032a954000 task.ti: ffff88032a954000
[ 1959.091865] RIP: 0010:[<ffffffffa040efba>] [<ffffffffa040efba>] dm_exception_store_set_chunk_size+0x7a/0x110 [dm_snapshot]
[ 1959.104295] RSP: 0018:ffff88032a957b30 EFLAGS: 00010246
[ 1959.110219] RAX: 0000000000000000 RBX: 0000000000000008 RCX: 0000000000000001
[ 1959.118180] RDX: 0000000000000000 RSI: 0000000000000008 RDI: ffff880329334a00
[ 1959.126141] RBP: ffff88032a957b50 R08: 0000000000000000 R09: 0000000000000001
[ 1959.134102] R10: 000000000000000a R11: f000000000000000 R12: ffff880330884d80
[ 1959.142061] R13: 0000000000000008 R14: ffffc90001c13088 R15: ffff880330884d80
[ 1959.150021] FS: 00007f8926ba3840(0000) GS:ffff880333440000(0000) knlGS:0000000000000000
[ 1959.159047] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1959.165456] CR2: 0000000000000098 CR3: 000000032f48b000 CR4: 00000000000006e0
[ 1959.173415] Stack:
[ 1959.175656] ffffc90001c13040 ffff880329334a00 ffff880330884ed0 ffff88032a957bdc
[ 1959.183946] ffff88032a957bb8 ffffffffa040f225 ffff880329334a30 ffff880300000000
[ 1959.192233] ffffffffa04133e0 ffff880329334b30 0000000830884d58 00000000569c58cf
[ 1959.200521] Call Trace:
[ 1959.203248] [<ffffffffa040f225>] dm_exception_store_create+0x1d5/0x240 [dm_snapshot]
[ 1959.211986] [<ffffffffa040d310>] snapshot_ctr+0x140/0x630 [dm_snapshot]
[ 1959.219469] [<ffffffffa0005c44>] ? dm_split_args+0x64/0x150 [dm_mod]
[ 1959.226656] [<ffffffffa0005ea7>] dm_table_add_target+0x177/0x440 [dm_mod]
[ 1959.234328] [<ffffffffa0009203>] table_load+0x143/0x370 [dm_mod]
[ 1959.241129] [<ffffffffa00090c0>] ? retrieve_status+0x1b0/0x1b0 [dm_mod]
[ 1959.248607] [<ffffffffa0009e35>] ctl_ioctl+0x255/0x4d0 [dm_mod]
[ 1959.255307] [<ffffffff813304e2>] ? memzero_explicit+0x12/0x20
[ 1959.261816] [<ffffffffa000a0c3>] dm_ctl_ioctl+0x13/0x20 [dm_mod]
[ 1959.268615] [<ffffffff81215eb6>] do_vfs_ioctl+0xa6/0x5c0
[ 1959.274637] [<ffffffff81120d2f>] ? __audit_syscall_entry+0xaf/0x100
[ 1959.281726] [<ffffffff81003176>] ? do_audit_syscall_entry+0x66/0x70
[ 1959.288814] [<ffffffff81216449>] SyS_ioctl+0x79/0x90
[ 1959.294450] [<ffffffff8167e4ae>] entry_SYSCALL_64_fastpath+0x12/0x71
...
[ 1959.323277] RIP [<ffffffffa040efba>] dm_exception_store_set_chunk_size+0x7a/0x110 [dm_snapshot]
[ 1959.333090] RSP <ffff88032a957b30>
[ 1959.336978] CR2: 0000000000000098
[ 1959.344121] ---[ end trace b049991ccad1169e ]---
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1195899
Signed-off-by: Ding Xiang <dingxiang@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 81ad4276b505e987dd8ebbdf63605f92cd172b52 upstream.
In some cases, platform thermal driver may report invalid trip points,
thermal core should not take any action for these trip points.
This fixed a regression that bogus trip point starts to screw up thermal
control on some Lenovo laptops, after
commit bb431ba26c5cd0a17c941ca6c3a195a3a6d5d461
Author: Zhang Rui <rui.zhang@intel.com>
Date: Fri Oct 30 16:31:47 2015 +0800
Thermal: initialize thermal zone device correctly
After thermal zone device registered, as we have not read any
temperature before, thus tz->temperature should not be 0,
which actually means 0C, and thermal trend is not available.
In this case, we need specially handling for the first
thermal_zone_device_update().
Both thermal core framework and step_wise governor is
enhanced to handle this. And since the step_wise governor
is the only one that uses trends, so it's the only thermal
governor that needs to be updated.
Tested-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: szegad <szegadlo@poczta.onet.pl>
Tested-by: prash <prash.n.rao@gmail.com>
Tested-by: amish <ammdispose-arch@yahoo.com>
Tested-by: Matthias <morpheusxyz123@yahoo.de>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1317190
Link: https://bugzilla.kernel.org/show_bug.cgi?id=114551
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b84106b4e2290c081cdab521fa832596cdfea246 upstream.
The PCI config header (first 64 bytes of each device's config space) is
defined by the PCI spec so generic software can identify the device and
manage its usage of I/O, memory, and IRQ resources.
Some non-spec-compliant devices put registers other than BARs where the
BARs should be. When the PCI core sizes these "BARs", the reads and writes
it does may have unwanted side effects, and the "BAR" may appear to
describe non-sensical address space.
Add a flag bit to mark non-compliant devices so we don't touch their BARs.
Turn off IO/MEM decoding to prevent the devices from consuming address
space, since we can't read the BARs to find out what that address space
would be.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For !BIO_CLONED bio, we can use .bi_vcnt safely, but it
doesn't mean we can just simply return .bi_io_vec[.bi_vcnt - 1]
because the start postion may have been moved in the middle of
the bvec, such as splitting in the middle of bvec.
Fixes: 7bcd79ac50d9(block: bio: introduce helpers to get the 1st and last bvec)
Cc: stable@vger.kernel.org
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"I previously sent a fix that prevents all trace events from being
called if the current cpu is offline.
But I forgot that in 3.18, we added lockdep checks to test RCU usage
even when the event is disabled. Although there cannot be any bug
when a cpu is going offline, we now get false warnings triggered by
the added checks of the event being disabled.
I removed the check from the tracepoint code itself, and added it to
the condition section (which is "1" for 'no condition'). This way the
online cpu check will get checked in all the right locations"
* tag 'trace-fixes-v4.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix check for cpu online when event is disabled
|
|
To keep consistent with kfree, which tolerate ptr is NULL. We do this
because sometimes we may use goto statement, so that success and failure
case can share parts of the code. But unfortunately, dma_free_coherent
called with parameter cpu_addr is null will cause oops, such as showed
below:
Unable to handle kernel paging request at virtual address ffffffc020d3b2b8
pgd = ffffffc083a61000
[ffffffc020d3b2b8] *pgd=0000000000000000, *pud=0000000000000000
CPU: 4 PID: 1489 Comm: malloc_dma_1 Tainted: G O 4.1.12 #1
Hardware name: ARM64 (DT)
PC is at __dma_free_coherent.isra.10+0x74/0xc8
LR is at __dma_free+0x9c/0xb0
Process malloc_dma_1 (pid: 1489, stack limit = 0xffffffc0837fc020)
[...]
Call trace:
__dma_free_coherent.isra.10+0x74/0xc8
__dma_free+0x9c/0xb0
malloc_dma+0x104/0x158 [dma_alloc_coherent_mtmalloc]
kthread+0xec/0xfc
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Functions which the compiler has instrumented for ASAN place poison on
the stack shadow upon entry and remove this poison prior to returning.
In some cases (e.g. hotplug and idle), CPUs may exit the kernel a
number of levels deep in C code. If there are any instrumented
functions on this critical path, these will leave portions of the idle
thread stack shadow poisoned.
If a CPU returns to the kernel via a different path (e.g. a cold
entry), then depending on stack frame layout subsequent calls to
instrumented functions may use regions of the stack with stale poison,
resulting in (spurious) KASAN splats to the console.
Contemporary GCCs always add stack shadow poisoning when ASAN is
enabled, even when asked to not instrument a function [1], so we can't
simply annotate functions on the critical path to avoid poisoning.
Instead, this series explicitly removes any stale poison before it can
be hit. In the common hotplug case we clear the entire stack shadow in
common code, before a CPU is brought online.
On architectures which perform a cold return as part of cpu idle may
retain an architecture-specific amount of stack contents. To retain the
poison for this retained context, the arch code must call the core KASAN
code, passing a "watermark" stack pointer value beyond which shadow will
be cleared. Architectures which don't perform a cold return as part of
idle do not need any additional code.
This patch (of 3):
Functions which the compiler has instrumented for KASAN place poison on
the stack shadow upon entry and remove this poision prior to returning.
In some cases (e.g. hotplug and idle), CPUs may exit the kernel a number
of levels deep in C code. If there are any instrumented functions on this
critical path, these will leave portions of the stack shadow poisoned.
If a CPU returns to the kernel via a different path (e.g. a cold entry),
then depending on stack frame layout subsequent calls to instrumented
functions may use regions of the stack with stale poison, resulting in
(spurious) KASAN splats to the console.
To avoid this, we must clear stale poison from the stack prior to
instrumented functions being called. This patch adds functions to the
KASAN core for removing poison from (portions of) a task's stack. These
will be used by subsequent patches to avoid problems with hotplug and
idle.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Given we have uninitialized list_heads being passed to list_add() it
will always be the case that those uninitialized values randomly trigger
the poison value. Especially since a list_add() operation will seed the
stack with the poison value for later stack allocations to trip over.
For example, see these two false positive reports:
list_add attempted on force-poisoned entry
WARNING: at lib/list_debug.c:34
[..]
NIP [c00000000043c390] __list_add+0xb0/0x150
LR [c00000000043c38c] __list_add+0xac/0x150
Call Trace:
__list_add+0xac/0x150 (unreliable)
__down+0x4c/0xf8
down+0x68/0x70
xfs_buf_lock+0x4c/0x150 [xfs]
list_add attempted on force-poisoned entry(0000000000000500),
new->next == d0000000059ecdb0, new->prev == 0000000000000500
WARNING: at lib/list_debug.c:33
[..]
NIP [c00000000042db78] __list_add+0xa8/0x140
LR [c00000000042db74] __list_add+0xa4/0x140
Call Trace:
__list_add+0xa4/0x140 (unreliable)
rwsem_down_read_failed+0x6c/0x1a0
down_read+0x58/0x60
xfs_log_commit_cil+0x7c/0x600 [xfs]
Fixes: commit 5c2c2587b132 ("mm, dax, pmem: introduce {get|put}_dev_pagemap() for dax-gup")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Eryu Guan <eguan@redhat.com>
Tested-by: Eryu Guan <eguan@redhat.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit f37755490fe9b ("tracepoints: Do not trace when cpu is offline") added
a check to make sure that tracepoints only get called when the cpu is
online, as it uses rcu_read_lock_sched() for protection.
Commit 3a630178fd5f3 ("tracing: generate RCU warnings even when tracepoints
are disabled") added lockdep checks (including rcu checks) for events that
are not enabled to catch possible RCU issues that would only be triggered if
a trace event was enabled. Commit f37755490fe9b only stopped the warnings
when the trace event was enabled but did not prevent warnings if the trace
event was called when disabled.
To fix this, the cpu online check is moved to where the condition is added
to the trace event. This will place the cpu online check in all places that
it may be used now and in the future.
Cc: stable@vger.kernel.org # v3.18+
Fixes: f37755490fe9b ("tracepoints: Do not trace when cpu is offline")
Fixes: 3a630178fd5f3 ("tracing: generate RCU warnings even when tracepoints are disabled")
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Pull networking fixes from David Miller:
1) Fix ordering of WEXT netlink messages so we don't see a newlink
after a dellink, from Johannes Berg.
2) Out of bounds access in minstrel_ht_set_best_prob_rage, from
Konstantin Khlebnikov.
3) Paging buffer memory leak in iwlwifi, from Matti Gottlieb.
4) Wrong units used to set initial TCP rto from cached metrics, also
from Konstantin Khlebnikov.
5) Fix stale IP options data in the SKB control block from leaking
through layers of encapsulation, from Bernie Harris.
6) Zero padding len miscalculated in bnxt_en, from Michael Chan.
7) Only CHECKSUM_PARTIAL packets should be passed down through GSO, fix
from Hannes Frederic Sowa.
8) Fix suspend/resume with JME networking devices, from Diego Violat
and Guo-Fu Tseng.
9) Checksums not validated properly in bridge multicast support due to
the placement of the SKB header pointers at the time of the check,
fix from Álvaro Fernández Rojas.
10) Fix hang/tiemout with r8169 if a stats fetch is done while the
device is runtime suspended. From Chun-Hao Lin.
11) The forwarding database netlink dump facilities don't track the
state of the dump properly, resulting in skipped/missed entries.
From Minoura Makoto.
12) Fix regression from a recent 3c59x bug fix, from Neil Horman.
13) Fix list corruption in bna driver, from Ivan Vecera.
14) Big endian machines crash on vlan add in bnx2x, fix from Michal
Schmidt.
15) Ethtool RSS configuration not propagated properly in mlx5 driver,
from Tariq Toukan.
16) Fix regression in PHY probing in stmmac driver, from Gabriel
Fernandez.
17) Fix SKB tailroom calculation in igmp/mld code, from Benjamin
Poirier.
18) A past change to skip empty routing headers in ipv6 extention header
parsing accidently caused fragment headers to not be matched any
longer. Fix from Florian Westphal.
19) eTSEC-106 erratum needs to be applied to more gianfar chips, from
Atsushi Nemoto.
20) Fix netdev reference after free via workqueues in usb networking
drivers, from Oliver Neukum and Bjørn Mork.
21) mdio->irq is now an array rather than a pointer to dynamic memory,
but several drivers were still trying to free it :-/ Fixes from
Colin Ian King.
22) act_ipt iptables action forgets to set the family field, thus LOG
netfilter targets don't work with it. Fix from Phil Sutter.
23) SKB leak in ibmveth when skb_linearize() fails, from Thomas Falcon.
24) pskb_may_pull() cannot be called with interrupts disabled, fix code
that tries to do this in vmxnet3 driver, from Neil Horman.
25) be2net driver leaks iomap'd memory on removal, fix from Douglas
Miller.
26) Forgotton RTNL mutex unlock in ppp_create_interface() error paths,
from Guillaume Nault.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (97 commits)
ppp: release rtnl mutex when interface creation fails
cdc_ncm: do not call usbnet_link_change from cdc_ncm_bind
tcp: fix tcpi_segs_in after connection establishment
net: hns: fix the bug about loopback
jme: Fix device PM wakeup API usage
jme: Do not enable NIC WoL functions on S0
udp6: fix UDP/IPv6 encap resubmit path
be2net: Don't leak iomapped memory on removal.
vmxnet3: avoid calling pskb_may_pull with interrupts disabled
net: ethernet: Add missing MFD_SYSCON dependency on HAS_IOMEM
ibmveth: check return of skb_linearize in ibmveth_start_xmit
cdc_ncm: toggle altsetting to force reset before setup
usbnet: cleanup after bind() in probe()
mlxsw: pci: Correctly determine if descriptor queue is full
mlxsw: spectrum: Always decrement bridge's ref count
tipc: fix nullptr crash during subscription cancel
net: eth: altera: do not free array priv->mdio->irq
net/ethoc: do not free array priv->mdio->irq
net: sched: fix act_ipt for LOG target
asix: do not free array priv->mdio->irq
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph fix from Sage Weil:
"This is a final commit we missed to align the protocol compatibility
with the feature bits.
It decodes a few extra fields in two different messages and reports
EIO when they are used (not yet supported)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: initial CEPH_FEATURE_FS_FILE_LAYOUT_V2 support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Assorted fixes for libata drivers.
- Turns out HDIO_GET_32BIT ioctl was subtly broken all along.
- Recent update to ahci external port handling was incorrectly
marking hotpluggable ports as external making userland handle
devices connected to those ports incorrectly.
- ahci_xgene needs its own irq handler to work around a hardware
erratum. libahci updated to allow irq handler override.
- Misc driver specific updates"
* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: ahci: don't mark HotPlugCapable Ports as external/removable
ahci: Workaround for ThunderX Errata#22536
libata: Align ata_device's id on a cacheline
Adding Intel Lewisburg device IDs for SATA
pata-rb532-cf: get rid of the irq_to_gpio() call
libata: fix HDIO_GET_32BIT ioctl
ahci_xgene: Implement the workaround to fix the missing of the edge interrupt for the HOST_IRQ_STAT.
ata: Remove the AHCI_HFLAG_EDGE_IRQ support from libahci.
libahci: Implement the capability to override the generic ahci interrupt handler.
|
|
Pull block fixes from Jens Axboe:
"Round 2 of this. I cut back to the bare necessities, the patch is
still larger than it usually would be at this time, due to the number
of NVMe fixes in there. This pull request contains:
- The 4 core fixes from Ming, that fix both problems with exceeding
the virtual boundary limit in case of merging, and the gap checking
for cloned bio's.
- NVMe fixes from Keith and Christoph:
- Regression on larger user commands, causing problems with
reading log pages (for instance). This touches both NVMe,
and the block core since that is now generally utilized also
for these types of commands.
- Hot removal fixes.
- User exploitable issue with passthrough IO commands, if !length
is given, causing us to fault on writing to the zero
page.
- Fix for a hang under error conditions
- And finally, the current series regression for umount with cgroup
writeback, where the final flush would happen async and hence open
up window after umount where the device wasn't consistent. fsck
right after umount would show this. From Tejun"
* 'for-linus2' of git://git.kernel.dk/linux-block:
block: support large requests in blk_rq_map_user_iov
block: fix blk_rq_get_max_sectors for driver private requests
nvme: fix max_segments integer truncation
nvme: set queue limits for the admin queue
writeback: flush inode cgroup wb switches instead of pinning super_block
NVMe: Fix 0-length integrity payload
NVMe: Don't allow unsupported flags
NVMe: Move error handling to failed reset handler
NVMe: Simplify device reset failure
NVMe: Fix namespace removal deadlock
NVMe: Use IDA for namespace disk naming
NVMe: Don't unmap controller registers on reset
block: merge: get the 1st and last bvec via helpers
block: get the 1st and last bvec via helpers
block: check virt boundary in bio_will_gap()
block: bio: introduce helpers to get the 1st and last bvec
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"A feature was added in 4.3 that allowed users to filter trace points
on a tasks "comm" field. But this prevented filtering on a comm field
that is within a trace event (like sched_migrate_task).
When trying to filter on when a program migrated, this change
prevented the filtering of the sched_migrate_task.
To fix this, the event fields are examined first, and then the extra
fields like "comm" and "cpu" are examined. Also, instead of testing
to assign the comm filter function based on the field's name, the
generic comm field is given a new filter type (FILTER_COMM). When
this field is used to filter the type is checked. The same is done
for the cpu filter field.
Two new special filter types are added: "COMM" and "CPU". This allows
users to still filter the tasks comm for events that have "comm" as
one of their fields, in cases that users would like to filter
sched_migrate_task on the comm of the task that called the event, and
not the comm of the task that is being migrated"
* tag 'trace-fixes-v4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Do not have 'comm' filter override event 'comm' field
|
|
Add support for the format change of MClientReply/MclientCaps.
Also add code that denies access to inodes with pool_ns layouts.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
|
|
Commit 9f61668073a8d "tracing: Allow triggers to filter for CPU ids and
process names" added a 'comm' filter that will filter events based on the
current tasks struct 'comm'. But this now hides the ability to filter events
that have a 'comm' field too. For example, sched_migrate_task trace event.
That has a 'comm' field of the task to be migrated.
echo 'comm == "bash"' > events/sched_migrate_task/filter
will now filter all sched_migrate_task events for tasks named "bash" that
migrates other tasks (in interrupt context), instead of seeing when "bash"
itself gets migrated.
This fix requires a couple of changes.
1) Change the look up order for filter predicates to look at the events
fields before looking at the generic filters.
2) Instead of basing the filter function off of the "comm" name, have the
generic "comm" filter have its own filter_type (FILTER_COMM). Test
against the type instead of the name to assign the filter function.
3) Add a new "COMM" filter that works just like "comm" but will filter based
on the current task, even if the trace event contains a "comm" field.
Do the same for "cpu" field, adding a FILTER_CPU and a filter "CPU".
Cc: stable@vger.kernel.org # v4.3+
Fixes: 9f61668073a8d "tracing: Allow triggers to filter for CPU ids and process names"
Reported-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Driver private request types should not get the artifical cap for the
FS requests. This is important to use the full device capabilities
for internal command or NVMe pass through commands.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Jeff Lien <Jeff.Lien@hgst.com>
Tested-by: Jeff Lien <Jeff.Lien@hgst.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Updated by me to use an explicit check for the one command type that
does support extended checking, instead of relying on the ordering
of the enum command values - as suggested by Keith.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
If cgroup writeback is in use, inodes can be scheduled for
asynchronous wb switching. Before 5ff8eaac1636 ("writeback: keep
superblock pinned during cgroup writeback association switches"), this
could race with umount leading to super_block being destroyed while
inodes are pinned for wb switching. 5ff8eaac1636 fixed it by bumping
s_active while wb switches are in flight; however, this allowed
in-flight wb switches to make umounts asynchronous when the userland
expected synchronosity - e.g. fsck immediately following umount may
fail because the device is still busy.
This patch removes the problematic super_block pinning and instead
makes generic_shutdown_super() flush in-flight wb switches. wb
switches are now executed on a dedicated isw_wq so that they can be
flushed and isw_nr_in_flight keeps track of the number of in-flight wb
switches so that flushing can be avoided in most cases.
v2: Move cgroup_writeback_umount() further below and add MS_ACTIVE
check in inode_switch_wbs() as Jan an Al suggested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Tahsin Erdogan <tahsin@google.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Link: http://lkml.kernel.org/g/CAAeU0aNCq7LGODvVGRU-oU_o-6enii5ey0p1c26D1ZzYwkDc5A@mail.gmail.com
Fixes: 5ff8eaac1636 ("writeback: keep superblock pinned during cgroup writeback association switches")
Cc: stable@vger.kernel.org #v4.5
Reviewed-by: Jan Kara <jack@suse.cz>
Tested-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This patch applies the two introduced helpers to
figure out the 1st and last bvec, and fixes the
original way after bio splitting.
Cc: stable@vger.kernel.org
Reported-by: Sagi Grimberg <sagig@dev.mellanox.co.il>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
