| Age | Commit message (Collapse) | Author |
|---|
|
commit c2b71462d294cf517a0bc6e4fd6424d7cee5596f upstream.
The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter. This allowed
a hub to be runtime suspended at a time when the driver did not expect
it. The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:
URB 0000000031fb463e submitted while active
WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363
The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count). The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.
Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls. In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.
This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative. There's
even a warning about this in the USB power management documentation!
As it happens, this is exactly what the hub driver does. The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread. This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.
It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock. The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts. As far as I know, all
existing drivers currently do this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3ff9c075cc767b3060bdac12da72fc94dd7da1b8 upstream.
Verify the stack frame pointer on kretprobe trampoline handler,
If the stack frame pointer does not match, it skips the wrong
entry and tries to find correct one.
This can happen if user puts the kretprobe on the function
which can be used in the path of ftrace user-function call.
Such functions should not be probed, so this adds a warning
message that reports which function should be blacklisted.
Tested-by: Andrea Righi <righi.andrea@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/155094059185.6137.15527904013362842072.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 27da0d2ef998e222a876c0cec72aa7829a626266 ]
A bugfix just broke compilation of appletalk when CONFIG_SYSCTL
is disabled:
In file included from net/appletalk/ddp.c:65:
net/appletalk/ddp.c: In function 'atalk_init':
include/linux/atalk.h:164:34: error: expected expression before 'do'
#define atalk_register_sysctl() do { } while(0)
^~
net/appletalk/ddp.c:1934:7: note: in expansion of macro 'atalk_register_sysctl'
rc = atalk_register_sysctl();
This is easier to avoid by using conventional inline functions
as stubs rather than macros. The header already has inline
functions for other purposes, so I'm changing over all the
macros for consistency.
Fixes: 6377f787aeb9 ("appletalk: Fix use-after-free in atalk_proc_exit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a4046c06be50a4f01d435aa7fe57514818e6cc82 ]
Use offsetof() to calculate offset of a field to take advantage of
compiler built-in version when possible, and avoid UBSAN warning when
compiling with Clang:
UBSAN: Undefined behaviour in mm/swapfile.c:3010:38
member access within null pointer of type 'union swap_header'
CPU: 6 PID: 1833 Comm: swapon Tainted: G S 4.19.23 #43
Call trace:
dump_backtrace+0x0/0x194
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0x70/0x94
ubsan_epilogue+0x14/0x44
ubsan_type_mismatch_common+0xf4/0xfc
__ubsan_handle_type_mismatch_v1+0x34/0x54
__se_sys_swapon+0x654/0x1084
__arm64_sys_swapon+0x1c/0x24
el0_svc_common+0xa8/0x150
el0_svc_compat_handler+0x2c/0x38
el0_svc_compat+0x8/0x18
Link: http://lkml.kernel.org/r/20190312081902.223764-1-pihsun@chromium.org
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6377f787aeb945cae7abbb6474798de129e1f3ac ]
KASAN report this:
BUG: KASAN: use-after-free in pde_subdir_find+0x12d/0x150 fs/proc/generic.c:71
Read of size 8 at addr ffff8881f41fe5b0 by task syz-executor.0/2806
CPU: 0 PID: 2806 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xfa/0x1ce lib/dump_stack.c:113
print_address_description+0x65/0x270 mm/kasan/report.c:187
kasan_report+0x149/0x18d mm/kasan/report.c:317
pde_subdir_find+0x12d/0x150 fs/proc/generic.c:71
remove_proc_entry+0xe8/0x420 fs/proc/generic.c:667
atalk_proc_exit+0x18/0x820 [appletalk]
atalk_exit+0xf/0x5a [appletalk]
__do_sys_delete_module kernel/module.c:1018 [inline]
__se_sys_delete_module kernel/module.c:961 [inline]
__x64_sys_delete_module+0x3dc/0x5e0 kernel/module.c:961
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fb2de6b9c58 EFLAGS: 00000246 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00000000200001c0
RBP: 0000000000000002 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fb2de6ba6bc
R13: 00000000004bccaa R14: 00000000006f6bc8 R15: 00000000ffffffff
Allocated by task 2806:
set_track mm/kasan/common.c:85 [inline]
__kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:496
slab_post_alloc_hook mm/slab.h:444 [inline]
slab_alloc_node mm/slub.c:2739 [inline]
slab_alloc mm/slub.c:2747 [inline]
kmem_cache_alloc+0xcf/0x250 mm/slub.c:2752
kmem_cache_zalloc include/linux/slab.h:730 [inline]
__proc_create+0x30f/0xa20 fs/proc/generic.c:408
proc_mkdir_data+0x47/0x190 fs/proc/generic.c:469
0xffffffffc10c01bb
0xffffffffc10c0166
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 2806:
set_track mm/kasan/common.c:85 [inline]
__kasan_slab_free+0x130/0x180 mm/kasan/common.c:458
slab_free_hook mm/slub.c:1409 [inline]
slab_free_freelist_hook mm/slub.c:1436 [inline]
slab_free mm/slub.c:2986 [inline]
kmem_cache_free+0xa6/0x2a0 mm/slub.c:3002
pde_put+0x6e/0x80 fs/proc/generic.c:647
remove_proc_entry+0x1d3/0x420 fs/proc/generic.c:684
0xffffffffc10c031c
0xffffffffc10c0166
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff8881f41fe500
which belongs to the cache proc_dir_entry of size 256
The buggy address is located 176 bytes inside of
256-byte region [ffff8881f41fe500, ffff8881f41fe600)
The buggy address belongs to the page:
page:ffffea0007d07f80 count:1 mapcount:0 mapping:ffff8881f6e69a00 index:0x0
flags: 0x2fffc0000000200(slab)
raw: 02fffc0000000200 dead000000000100 dead000000000200 ffff8881f6e69a00
raw: 0000000000000000 00000000800c000c 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881f41fe480: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff8881f41fe500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881f41fe580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881f41fe600: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff8881f41fe680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
It should check the return value of atalk_proc_init fails,
otherwise atalk_exit will trgger use-after-free in pde_subdir_find
while unload the module.This patch fix error cleanup path of atalk_init
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 08a77676f9c5fc69a681ccd2cd8140e65dcb26c7 upstream.
e7fd37ba1217 ("cgroup: avoid copying strings longer than the buffers")
converted possibly unsafe strncpy() usages in cgroup to strscpy().
However, although the callsites are completely fine with truncated
copied, because strscpy() is marked __must_check, it led to the
following warnings.
kernel/cgroup/cgroup.c: In function ‘cgroup_file_name’:
kernel/cgroup/cgroup.c:1400:10: warning: ignoring return value of ‘strscpy’, declared with attribute warn_unused_result [-Wunused-result]
strscpy(buf, cft->name, CGROUP_FILE_NAME_MAX);
^
To avoid the warnings, 50034ed49645 ("cgroup: use strlcpy() instead of
strscpy() to avoid spurious warning") switched them to strlcpy().
strlcpy() is worse than strlcpy() because it unconditionally runs
strlen() on the source string, and the only reason we switched to
strlcpy() here was because it was lacking __must_check, which doesn't
reflect any material differences between the two function. It's just
that someone added __must_check to strscpy() and not to strlcpy().
These basic string copy operations are used in variety of ways, and
one of not-so-uncommon use cases is safely handling truncated copies,
where the caller naturally doesn't care about the return value. The
__must_check doesn't match the actual use cases and forces users to
opt for inferior variants which lack __must_check by happenstance or
spread ugly (void) casts.
Remove __must_check from strscpy() and restore strscpy() usages in
cgroup.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ma Shimiao <mashimiao.fnst@cn.fujitsu.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
[backport only the string.h portion to remove build warnings starting to show up - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5f074f3e192f10c9fade898b9b3b8812e3d83342 ]
A recent optimization in Clang (r355672) lowers comparisons of the
return value of memcmp against zero to comparisons of the return value
of bcmp against zero. This helps some platforms that implement bcmp
more efficiently than memcmp. glibc simply aliases bcmp to memcmp, but
an optimized implementation is in the works.
This results in linkage failures for all targets with Clang due to the
undefined symbol. For now, just implement bcmp as a tailcail to memcmp
to unbreak the build. This routine can be further optimized in the
future.
Other ideas discussed:
* A weak alias was discussed, but breaks for architectures that define
their own implementations of memcmp since aliases to declarations are
not permitted (only definitions). Arch-specific memcmp
implementations typically declare memcmp in C headers, but implement
them in assembly.
* -ffreestanding also is used sporadically throughout the kernel.
* -fno-builtin-bcmp doesn't work when doing LTO.
Link: https://bugs.llvm.org/show_bug.cgi?id=41035
Link: https://code.woboq.org/userspace/glibc/string/memcmp.c.html#bcmp
Link: https://github.com/llvm/llvm-project/commit/8e16d73346f8091461319a7dfc4ddd18eedcff13
Link: https://github.com/ClangBuiltLinux/linux/issues/416
Link: http://lkml.kernel.org/r/20190313211335.165605-1-ndesaulniers@google.com
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Reported-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: James Y Knight <jyknight@google.com>
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 31b265b3baaf55f209229888b7ffea523ddab366 ]
As reported back in 2016-11 [1], the "ftdump" kdb command triggers a
BUG for "sleeping function called from invalid context".
kdb's "ftdump" command wants to call ring_buffer_read_prepare() in
atomic context. A very simple solution for this is to add allocation
flags to ring_buffer_read_prepare() so kdb can call it without
triggering the allocation error. This patch does that.
Note that in the original email thread about this, it was suggested
that perhaps the solution for kdb was to either preallocate the buffer
ahead of time or create our own iterator. I'm hoping that this
alternative of adding allocation flags to ring_buffer_read_prepare()
can be considered since it means I don't need to duplicate more of the
core trace code into "trace_kdb.c" (for either creating my own
iterator or re-preparing a ring allocator whose memory was already
allocated).
NOTE: another option for kdb is to actually figure out how to make it
reuse the existing ftrace_dump() function and totally eliminate the
duplication. This sounds very appealing and actually works (the "sr
z" command can be seen to properly dump the ftrace buffer). The
downside here is that ftrace_dump() fully consumes the trace buffer.
Unless that is changed I'd rather not use it because it means "ftdump
| grep xyz" won't be very useful to search the ftrace buffer since it
will throw away the whole trace on the first grep. A future patch to
dump only the last few lines of the buffer will also be hard to
implement.
[1] https://lkml.kernel.org/r/20161117191605.GA21459@google.com
Link: http://lkml.kernel.org/r/20190308193205.213659-1-dianders@chromium.org
Reported-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net)
commit 1602f49b58abcb0d34a5f0a29d68e7c1769547aa upstream.
[This commit was a merge, but it added hlist_add_tail_rcu(), which is what we
need in this stable tree, so I've changed the subject to be more descriptive
- gregkh]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 13054abbaa4f1fd4e6f3b4b63439ec033b4c8035 upstream.
Ring buffer implementation in hid_debug_event() and hid_debug_events_read()
is strange allowing lost or corrupted data. After commit 717adfdaf147
("HID: debug: check length before copy_to_user()") it is possible to enter
an infinite loop in hid_debug_events_read() by providing 0 as count, this
locks up a system. Fix this by rewriting the ring buffer implementation
with kfifo and simplify the code.
This fixes CVE-2019-3819.
v2: fix an execution logic and add a comment
v3: use __set_current_state() instead of set_current_state()
Backport to v3.18: some (tree-wide) patches are missing in v3.18 so
cherry-pick relevant pieces from:
* 6396bb221514 ("treewide: kzalloc() -> kcalloc()")
* a9a08845e9ac ("vfs: do bulk POLL* -> EPOLL* replacement")
* 92529623d242 ("HID: debug: improve hid_debug_event()")
* 174cd4b1e5fb ("sched/headers: Prepare to move signal wakeup & sigpending
methods from <linux/sched.h> into <linux/sched/signal.h>")
* 8fec02a73e31 ("HID: debug: fix error handling in hid_debug_events_read()")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1669187
Cc: stable@vger.kernel.org # v4.18+
Fixes: cd667ce24796 ("HID: use debugfs for events/reports dumping")
Fixes: 717adfdaf147 ("HID: debug: check length before copy_to_user()")
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a52c5a16cf19d8a85831bb1b915a221dd4ffae3c ]
There are several warnings from Clang about no case statement matching
the constant 0:
In file included from drivers/block/drbd/drbd_receiver.c:48:
In file included from drivers/block/drbd/drbd_int.h:48:
In file included from ./include/linux/drbd_genl_api.h:54:
In file included from ./include/linux/genl_magic_struct.h:236:
./include/linux/drbd_genl.h:321:1: warning: no case matching constant
switch condition '0'
GENL_struct(DRBD_NLA_HELPER, 24, drbd_helper_info,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/genl_magic_struct.h:220:10: note: expanded from macro
'GENL_struct'
switch (0) {
^
Silence this warning by adding a 'case 0:' statement. Additionally,
adjust the alignment of the statements in the ct_assert_unique macro to
avoid a checkpatch warning.
This solution was originally sent by Arnd Bergmann with a default case
statement: https://lore.kernel.org/patchwork/patch/756723/
Link: https://github.com/ClangBuiltLinux/linux/issues/43
Suggested-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d4b09acf924b84bae77cad090a9d108e70b43643 upstream.
if node have NFSv41+ mounts inside several net namespaces
it can lead to use-after-free in svc_process_common()
svc_process_common()
/* Setup reply header */
rqstp->rq_xprt->xpt_ops->xpo_prep_reply_hdr(rqstp); <<< HERE
svc_process_common() can use incorrect rqstp->rq_xprt,
its caller function bc_svc_process() takes it from serv->sv_bc_xprt.
The problem is that serv is global structure but sv_bc_xprt
is assigned per-netnamespace.
According to Trond, the whole "let's set up rqstp->rq_xprt
for the back channel" is nothing but a giant hack in order
to work around the fact that svc_process_common() uses it
to find the xpt_ops, and perform a couple of (meaningless
for the back channel) tests of xpt_flags.
All we really need in svc_process_common() is to be able to run
rqstp->rq_xprt->xpt_ops->xpo_prep_reply_hdr()
Bruce J Fields points that this xpo_prep_reply_hdr() call
is an awfully roundabout way just to do "svc_putnl(resv, 0);"
in the tcp case.
This patch does not initialiuze rqstp->rq_xprt in bc_svc_process(),
now it calls svc_process_common() with rqstp->rq_xprt = NULL.
To adjust reply header svc_process_common() just check
rqstp->rq_prot and calls svc_tcp_prep_reply_hdr() for tcp case.
To handle rqstp->rq_xprt = NULL case in functions called from
svc_process_common() patch intruduces net namespace pointer
svc_rqst->rq_bc_net and adjust SVC_NET() definition.
Some other function was also adopted to properly handle described case.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Cc: stable@vger.kernel.org
Fixes: 23c20ecd4475 ("NFS: callback up - users counting cleanup")
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
v2: - added lost extern svc_tcp_prep_reply_hdr()
- context changes in svc_process_common()
- dropped trace_svc_process() changes
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 78c9c4dfbf8c04883941445a195276bb4bb92c76 upstream.
The posix timer overrun handling is broken because the forwarding functions
can return a huge number of overruns which does not fit in an int. As a
consequence timer_getoverrun(2) and siginfo::si_overrun can turn into
random number generators.
The k_clock::timer_forward() callbacks return a 64 bit value now. Make
k_itimer::ti_overrun[_last] 64bit as well, so the kernel internal
accounting is correct. 3Remove the temporary (int) casts.
Add a helper function which clamps the overrun value returned to user space
via timer_getoverrun(2) or siginfo::si_overrun limited to a positive value
between 0 and INT_MAX. INT_MAX is an indicator for user space that the
overrun value has been clamped.
Reported-by: Team OWL337 <icytxw@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Link: https://lkml.kernel.org/r/20180626132705.018623573@linutronix.de
[florian: Make patch apply to v4.9.135]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3756f6401c302617c5e091081ca4d26ab604bec5 upstream.
gcc-8 warns about using strncpy() with the source size as the limit:
fs/exec.c:1223:32: error: argument to 'sizeof' in 'strncpy' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
This is indeed slightly suspicious, as it protects us from source
arguments without NUL-termination, but does not guarantee that the
destination is terminated.
This keeps the strncpy() to ensure we have properly padded target
buffer, but ensures that we use the correct length, by passing the
actual length of the destination buffer as well as adding a build-time
check to ensure it is exactly TASK_COMM_LEN.
There are only 23 callsites which I all reviewed to ensure this is
currently the case. We could get away with doing only the check or
passing the right length, but it doesn't hurt to do both.
Link: http://lkml.kernel.org/r/20171205151724.1764896-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Kees Cook <keescook@chromium.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Serge Hallyn <serge@hallyn.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Aleksa Sarai <asarai@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream.
When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
__can_get_echo_skb()
commit a4310fa2f24687888ce80fdb0e88583561a23700 upstream.
This patch factors out all non sending parts of can_get_echo_skb() into
a seperate function __can_get_echo_skb(), so that it can be re-used in
an upcoming patch.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db68ce10c4f0a27c1ff9fa0e789e5c41f8c4ea63 upstream.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[only take the include/linux/uaccess.h portion - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94e6992bb560be8bffb47f287194adf070b57695 upstream.
If the read is large enough, we end up spinning in the messenger:
libceph: osd0 192.168.122.1:6801 io error
libceph: osd0 192.168.122.1:6801 io error
libceph: osd0 192.168.122.1:6801 io error
This is a receive side limit, so only reads were affected.
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3f2aa244ee1a0d17ed5b6c86564d2c1b24d1c96b upstream.
Fix a TURBOchannel support regression with commit 205e1b7f51e4
("dma-mapping: warn when there is no coherent_dma_mask") that caused
coherent DMA allocations to produce a warning such as:
defxx: v1.11 2014/07/01 Lawrence V. Stefani and others
tc1: DEFTA at MMIO addr = 0x1e900000, IRQ = 20, Hardware addr = 08-00-2b-a3-a3-29
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at ./include/linux/dma-mapping.h:516 dfx_dev_register+0x670/0x678
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.19.0-rc6 #2
Stack : ffffffff8009ffc0 fffffffffffffec0 0000000000000000 ffffffff80647650
0000000000000000 0000000000000000 ffffffff806f5f80 ffffffffffffffff
0000000000000000 0000000000000000 0000000000000001 ffffffff8065d4e8
98000000031b6300 ffffffff80563478 ffffffff805685b0 ffffffffffffffff
0000000000000000 ffffffff805d6720 0000000000000204 ffffffff80388df8
0000000000000000 0000000000000009 ffffffff8053efd0 ffffffff806657d0
0000000000000000 ffffffff803177f8 0000000000000000 ffffffff806d0000
9800000003078000 980000000307b9e0 000000001e900000 ffffffff80067940
0000000000000000 ffffffff805d6720 0000000000000204 ffffffff80388df8
ffffffff805176c0 ffffffff8004dc78 0000000000000000 ffffffff80067940
...
Call Trace:
[<ffffffff8004dc78>] show_stack+0xa0/0x130
[<ffffffff80067940>] __warn+0x128/0x170
---[ end trace b1d1e094f67f3bb2 ]---
This is because the TURBOchannel bus driver fails to set the coherent
DMA mask for devices enumerated.
Set the regular and coherent DMA masks for TURBOchannel devices then,
observing that the bus protocol supports a 34-bit (16GiB) DMA address
space, by interpreting the value presented in the address cycle across
the 32 `ad' lines as a 32-bit word rather than byte address[1]. The
architectural size of the TURBOchannel DMA address space exceeds the
maximum amount of RAM any actual TURBOchannel system in existence may
have, hence both masks are the same.
This removes the warning shown above.
References:
[1] "TURBOchannel Hardware Specification", EK-369AA-OD-007B, Digital
Equipment Corporation, January 1993, Section "DMA", pp. 1-15 -- 1-17
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20835/
Fixes: 205e1b7f51e4 ("dma-mapping: warn when there is no coherent_dma_mask")
Cc: stable@vger.kernel.org # 4.16+
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6b2a3d628aa752f0ab825fc6d4d07b09e274d1c1 ]
The data to audit/record is in the 'from' buffer (ie., the input
read buffer).
Fixes: 72586c6061ab ("n_tty: Fix auditing support for cannonical mode")
Cc: stable <stable@vger.kernel.org> # 4.1+
Cc: Miloslav Trmač <mitr@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7829fb09a2b4268b30dd9bc782fa5ebee278b137 ]
In commit 0b053c951829 ("lib: memzero_explicit: use barrier instead
of OPTIMIZER_HIDE_VAR"), we made memzero_explicit() more robust in
case LTO would decide to inline memzero_explicit() and eventually
find out it could be elimiated as dead store.
While using barrier() works well for the case of gcc, recent efforts
from LLVMLinux people suggest to use llvm as an alternative to gcc,
and there, Stephan found in a simple stand-alone user space example
that llvm could nevertheless optimize and thus elimitate the memset().
A similar issue has been observed in the referenced llvm bug report,
which is regarded as not-a-bug.
Based on some experiments, icc is a bit special on its own, while it
doesn't seem to eliminate the memset(), it could do so with an own
implementation, and then result in similar findings as with llvm.
The fix in this patch now works for all three compilers (also tested
with more aggressive optimization levels). Arguably, in the current
kernel tree it's more of a theoretical issue, but imho, it's better
to be pedantic about it.
It's clearly visible with gcc/llvm though, with the below code: if we
would have used barrier() only here, llvm would have omitted clearing,
not so with barrier_data() variant:
static inline void memzero_explicit(void *s, size_t count)
{
memset(s, 0, count);
barrier_data(s);
}
int main(void)
{
char buff[20];
memzero_explicit(buff, sizeof(buff));
return 0;
}
$ gcc -O2 test.c
$ gdb a.out
(gdb) disassemble main
Dump of assembler code for function main:
0x0000000000400400 <+0>: lea -0x28(%rsp),%rax
0x0000000000400405 <+5>: movq $0x0,-0x28(%rsp)
0x000000000040040e <+14>: movq $0x0,-0x20(%rsp)
0x0000000000400417 <+23>: movl $0x0,-0x18(%rsp)
0x000000000040041f <+31>: xor %eax,%eax
0x0000000000400421 <+33>: retq
End of assembler dump.
$ clang -O2 test.c
$ gdb a.out
(gdb) disassemble main
Dump of assembler code for function main:
0x00000000004004f0 <+0>: xorps %xmm0,%xmm0
0x00000000004004f3 <+3>: movaps %xmm0,-0x18(%rsp)
0x00000000004004f8 <+8>: movl $0x0,-0x8(%rsp)
0x0000000000400500 <+16>: lea -0x18(%rsp),%rax
0x0000000000400505 <+21>: xor %eax,%eax
0x0000000000400507 <+23>: retq
End of assembler dump.
As gcc, clang, but also icc defines __GNUC__, it's sufficient to define
this in compiler-gcc.h only to be picked up. For a fallback or otherwise
unsupported compiler, we define it as a barrier. Similarly, for ecc which
does not support gcc inline asm.
Reference: https://llvm.org/bugs/show_bug.cgi?id=15495
Reported-by: Stephan Mueller <smueller@chronox.de>
Tested-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Stephan Mueller <smueller@chronox.de>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: mancha security <mancha1@zoho.com>
Cc: Mark Charlebois <charlebm@gmail.com>
Cc: Behan Webster <behanw@converseincode.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ceb3a16c070c403f5f9ca46b46cf2bb79ea11750 ]
Ensure that we cache the NFSv4/v4.1 client owner_id so that we can
verify it when we're doing trunking detection.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0bc09f9cdc589e0b54724096138996a00b19babb ]
Prior to DRA74x silicon rev 1.1, pcie_pcs register bits 8-15 and bits 16-23
were used to configure RC delay count for phy1 and phy2 respectively.
phyid was used as index to distinguish the phys and to configure the delay
values appropriately.
As of DRA74x silicon rev 1.1, pcie_pcs register definition has changed.
Bits 16-23 are used to configure delay values for *both* phy1 and phy2.
Hence phyid is no longer required.
So, drop id field from ti_pipe3 structure and its subsequent references
for configuring pcie_pcs register.
Also, pcie_pcs register now needs to be configured with delay value of 0x96
at bit positions 16-23. See register description of CTRL_CORE_PCIE_PCS in
ARM572x TRM, SPRUHZ6, October 2014, section 18.5.2.2, table 18-1804.
This is needed to ensure Gen2 cards are enumerated consistently.
DRA72x silicon behaves same way as DRA74x rev 1.1 as far as this functionality
is considered.
Test results on DRA74x and DRA72x EVMs:
Before patch
------------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register
DRA72x: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register
After patch
-----------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards work consistently.
DRA72x: Gen1 and Gen2 cards enumerate consistently.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c953d63548207a085abcb12a15fefc8a11ffdf0a upstream.
The info->target comes from userspace and it would be used directly.
So we need to add the sanity check to make sure it is a valid standard
target, although the ebtables tool has already checked it. Kernel needs
to validate anything coming from userspace.
If the target is set as an evil value, it would break the ebtables
and cause a panic. Because the non-standard target is treated as one
offset.
Now add one helper function ebt_invalid_target, and we would replace
the macro INVALID_TARGET later.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Loic <hackurx@opensec.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34dbbcdbf63360661ff7bda6c5f52f99ac515f92 upstream.
A lot of seqfile users seem to be using things like %pK that uses the
credentials of the current process, but that is actually completely
wrong for filesystem interfaces.
The unix semantics for permission checking files is to check permissions
at _open_ time, not at read or write time, and that is not just a small
detail: passing off stdin/stdout/stderr to a suid application and making
the actual IO happen in privileged context is a classic exploit
technique.
So if we want to be able to look at permissions at read time, we need to
use the file open credentials, not the current ones. Normal file
accesses can just use "f_cred" (or any of the helper functions that do
that, like file_ns_capable()), but the seqfile interfaces do not have
any such options.
It turns out that seq_file _does_ save away the user_ns information of
the file, though. Since user_ns is just part of the full credential
information, replace that special case with saving off the cred pointer
instead, and suddenly seq_file has all the permission information it
needs.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e5d9998f3e09359b372a037a6ac55ba235d95d57 upstream.
/*
* cpu_partial determined the maximum number of objects
* kept in the per cpu partial lists of a processor.
*/
Can't be negative.
Link: http://lkml.kernel.org/r/20180305200730.15812-15-adobriyan@gmail.com
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a9cdebdcc17e426fb5287e4a82db1dfe86339b2 upstream.
Jann Horn points out that the vmacache_flush_all() function is not only
potentially expensive, it's buggy too. It also happens to be entirely
unnecessary, because the sequence number overflow case can be avoided by
simply making the sequence number be 64-bit. That doesn't even grow the
data structures in question, because the other adjacent fields are
already 64-bit.
So simplify the whole thing by just making the sequence number overflow
case go away entirely, which gets rid of all the complications and makes
the code faster too. Win-win.
[ Oleg Nesterov points out that the VMACACHE_FULL_FLUSHES statistics
also just goes away entirely with this ]
Reported-by: Jann Horn <jannh@google.com>
Suggested-by: Will Deacon <will.deacon@arm.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2afc9166f79b8f6da5f347f48515215ceee4ae37 upstream.
Introduce these two functions and export them such that the next patch
can add calls to these functions from the SCSI core.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 73c8d8945505acdcbae137c2e00a1232e0be709f upstream.
Maintain the tracing on/off setting of the ring_buffer when switching
to the trace buffer snapshot.
Taking a snapshot is done by swapping the backup ring buffer
(max_tr_buffer). But since the tracing on/off setting is defined
by the ring buffer, when swapping it, the tracing on/off setting
can also be changed. This causes a strange result like below:
/sys/kernel/debug/tracing # cat tracing_on
1
/sys/kernel/debug/tracing # echo 0 > tracing_on
/sys/kernel/debug/tracing # cat tracing_on
0
/sys/kernel/debug/tracing # echo 1 > snapshot
/sys/kernel/debug/tracing # cat tracing_on
1
/sys/kernel/debug/tracing # echo 1 > snapshot
/sys/kernel/debug/tracing # cat tracing_on
0
We don't touch tracing_on, but snapshot changes tracing_on
setting each time. This is an anomaly, because user doesn't know
that each "ring_buffer" stores its own tracing-enable state and
the snapshot is done by swapping ring buffers.
Link: http://lkml.kernel.org/r/153149929558.11274.11730609978254724394.stgit@devbox
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Hiraku Toyooka <hiraku.toyooka@cybertrust.co.jp>
Cc: stable@vger.kernel.org
Fixes: debdd57f5145 ("tracing: Make a snapshot feature available from userspace")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
[ Updated commit log and comment in the code ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8b7008620b8452728cadead460a36f64ed78c460 ]
The pfmemalloc flag indicates that the skb was allocated from
the PFMEMALLOC reserves, and the flag is currently copied on skb
copy and clone.
However, an skb copied from an skb flagged with pfmemalloc
wasn't necessarily allocated from PFMEMALLOC reserves, and on
the other hand an skb allocated that way might be copied from an
skb that wasn't.
So we should not copy the flag on skb copy, and rather decide
whether to allow an skb to be associated with sockets unrelated
to page reclaim depending only on how it was allocated.
Move the pfmemalloc flag before headers_start[0] using an
existing 1-bit hole, so that __copy_skb_header() doesn't copy
it.
When cloning, we'll now take care of this flag explicitly,
contravening to the warning comment of __skb_clone().
While at it, restore the newline usage introduced by commit
b19372273164 ("net: reorganize sk_buff for faster
__copy_skb_header()") to visually separate bytes used in
bitfields after headers_start[0], that was gone after commit
a9e419dc7be6 ("netfilter: merge ctinfo into nfct pointer storage
area"), and describe the pfmemalloc flag in the kernel-doc
structure comment.
This doesn't change the size of sk_buff or cacheline boundaries,
but consolidates the 15 bits hole before tc_index into a 2 bytes
hole before csum, that could now be filled more easily.
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Fixes: c93bdd0e03e8 ("netvm: allow skb allocation to use PFMEMALLOC reserves")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15bfd21fbc5d35834b9ea383dc458a1f0c9e3434 upstream.
A device may have boundary restrictions where the number of sectors
between boundaries exceeds its max transfer size. In this case, we need
to cap the max size to the smaller of the two limits.
Reported-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Tested-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2026d35741f2c3ece73c11eb7e4a15d7c2df9ebe upstream.
The function __builtin_expect returns long type (see the gcc
documentation), and so do macros likely and unlikely. Unfortunatelly, when
CONFIG_PROFILE_ANNOTATED_BRANCHES is selected, the macros likely and
unlikely expand to __branch_check__ and __branch_check__ truncates the
long type to int. This unintended truncation may cause bugs in various
kernel code (we found a bug in dm-writecache because of it), so it's
better to fix __branch_check__ to return long.
Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1805300818140.24812@file01.intranet.prod.int.rdu2.redhat.com
Cc: Ingo Molnar <mingo@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 1f0d69a9fc815 ("tracing: profile likely and unlikely annotations")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 607065bad9931e72207b0cac365d7d4abc06bd99 upstream.
When using large tcp_rmem[2] values (I did tests with 500 MB),
I noticed overflows while computing rcvwin.
Lets fix this before the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Backport: sysctl_tcp_rmem is not Namespace-ify'd in older kernels]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5d6ae4f0da8a64a185074dabb1b2f8c148efa741 ]
When handling an OS descriptor request, one of the first operations is
to zero out the request buffer using the wLength from the setup packet.
There is no bounds checking, so a wLength > 4096 would clobber memory
adjacent to the request buffer. Fix this by taking the min of wLength
and the request buffer length prior to the memset. While at it, define
the buffer length in a header file so that magic numbers don't appear
throughout the code.
When returning data to the host, the data length should be the min of
the wLength and the valid data we have to return. Currently we are
returning wLength, thus requests for a wLength greater than the amount
of data in the OS descriptor buffer would return invalid (albeit zero'd)
data following the valid descriptor data. Fix this by counting the
number of bytes when constructing the data and using this when
determining the length of the request.
Signed-off-by: Chris Dickens <christopher.a.dickens@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 328008a72d38b5bde6491e463405c34a81a65d3e ]
The declaration for swsusp_arch_resume marks it as 'asmlinkage', but the
definition in x86-32 does not, and it fails to include the header with the
declaration. This leads to a warning when building with
link-time-optimizations:
kernel/power/power.h:108:23: error: type of 'swsusp_arch_resume' does not match original declaration [-Werror=lto-type-mismatch]
extern asmlinkage int swsusp_arch_resume(void);
^
arch/x86/power/hibernate_32.c:148:0: note: 'swsusp_arch_resume' was previously declared here
int swsusp_arch_resume(void)
This moves the declaration into a globally visible header file and fixes up
both x86 definitions to match it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: linux-pm@vger.kernel.org
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Link: https://lkml.kernel.org/r/20180202145634.200291-2-arnd@arndb.de
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1e2e547a93a00ebc21582c06ca3c6cfea2a309ee upstream.
For anything NFS-exported we do _not_ want to unlock new inode
before it has grown an alias; original set of fixes got the
ordering right, but missed the nasty complication in case of
lockdep being enabled - unlock_new_inode() does
lockdep_annotate_inode_mutex_key(inode)
which can only be done before anyone gets a chance to touch
->i_mutex. Unfortunately, flipping the order and doing
unlock_new_inode() before d_instantiate() opens a window when
mkdir can race with open-by-fhandle on a guessed fhandle, leading
to multiple aliases for a directory inode and all the breakage
that follows from that.
Correct solution: a new primitive (d_instantiate_new())
combining these two in the right order - lockdep annotate, then
d_instantiate(), then the rest of unlock_new_inode(). All
combinations of d_instantiate() with unlock_new_inode() should
be converted to that.
Cc: stable@kernel.org # 2.6.29 and later
Tested-by: Mike Marshall <hubcap@omnibond.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
definition for mixed mode
commit 0b3225ab9407f557a8e20f23f37aa7236c10a9b1 upstream.
Mixed mode allows a kernel built for x86_64 to interact with 32-bit
EFI firmware, but requires us to define all struct definitions carefully
when it comes to pointer sizes.
'struct efi_pci_io_protocol_32' currently uses a 'void *' for the
'romimage' field, which will be interpreted as a 64-bit field
on such kernels, potentially resulting in bogus memory references
and subsequent crashes.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20180504060003.19618-13-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6510bbc88e3258631831ade49033537081950605 upstream.
Currently it is possible to read and/or write to suspend EB's.
Writing /dev/mtdX or /dev/mtdblockX from several processes may
break the flash state machine.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 24a7e4d20783c0514850f24a5c41ede46ab058f0 upstream.
For cleanup it's helpful to be able to simply scan all vqs and discard
all data. Add an iterator to do that.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6dc06c08bef1c746ff8da33dab677cfbacdcad32 ]
Our previous patch (cited below) introduced a regression
for RAW Eth QPs.
Fix it by checking if the QP number provided by user-space
exists, hence allowing steering rules to be added for valid
QPs only.
Fixes: 89c557687a32 ("net/mlx4_en: Avoid adding steering rules with invalid ring")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 48a1df65334b74bd7531f932cca5928932abf769 ]
This is a defense-in-depth measure in response to bugs like
4d6fa57b4dab ("macsec: avoid heap overflow in skb_to_sgvec"). There's
not only a potential overflow of sglist items, but also a stack overflow
potential, so we fix this by limiting the amount of recursion this function
is allowed to do. Not actually providing a bounded base case is a future
disaster that we can easily avoid here.
As a small matter of house keeping, we take this opportunity to move the
documentation comment over the actual function the documentation is for.
While this could be implemented by using an explicit stack of skbuffs,
when implementing this, the function complexity increased considerably,
and I don't think such complexity and bloat is actually worth it. So,
instead I built this and tested it on x86, x86_64, ARM, ARM64, and MIPS,
and measured the stack usage there. I also reverted the recent MIPS
changes that give it a separate IRQ stack, so that I could experience
some worst-case situations. I found that limiting it to 24 layers deep
yielded a good stack usage with room for safety, as well as being much
deeper than any driver actually ever creates.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Howells <dhowells@redhat.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 65376df582174ffcec9e6471bf5b0dd79ba05e4a upstream.
Commit b76437579d13 ("procfs: mark thread stack correctly in
proc/<pid>/maps") added [stack:TID] annotation to /proc/<pid>/maps.
Finding the task of a stack VMA requires walking the entire thread list,
turning this into quadratic behavior: a thousand threads means a
thousand stacks, so the rendering of /proc/<pid>/maps needs to look at a
million combinations.
The cost is not in proportion to the usefulness as described in the
patch.
Drop the [stack:TID] annotation to make /proc/<pid>/maps (and
/proc/<pid>/numa_maps) usable again for higher thread counts.
The [stack] annotation inside /proc/<pid>/task/<tid>/maps is retained, as
identifying the stack VMA there is an O(1) operation.
Siddesh said:
"The end users needed a way to identify thread stacks programmatically and
there wasn't a way to do that. I'm afraid I no longer remember (or have
access to the resources that would aid my memory since I changed
employers) the details of their requirement. However, I did do this on my
own time because I thought it was an interesting project for me and nobody
really gave any feedback then as to its utility, so as far as I am
concerned you could roll back the main thread maps information since the
information is available in the thread-specific files"
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Siddhesh Poyarekar <siddhesh.poyarekar@gmail.com>
Cc: Shaohua Li <shli@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b1d0a5d0cba4597c0394997b2d5fced3e3841b4e upstream.
recent and hashlimit both create /proc files, but only check that
name is 0 terminated.
This can trigger WARN() from procfs when name is "" or "/".
Add helper for this and then use it for both.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: <syzbot+0502b00edac2a0680b61@syzkaller.appspotmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 16b114a6d7973cf027e4c2b23eae1076eaf98c25 upstream.
USB spec specifies wMaxPacketSize to be little endian (as other properties),
so when using this variable in the driver we should convert to the current
CPU endianness if necessary.
This patch also introduces usb_ep_align() which does always returns the
aligned buffer size for an endpoint. This is useful to be used by USB requests
allocator functions.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0c08aaf873174c95e674cf21ffcd041c589d2e5b ]
ISL9305_MAX_REGULATOR is the last index used to access the init_data[]
array, so we need to add one to this last index to obtain the necessary
array size.
This fixes the following smatch error:
drivers/regulator/isl9305.c:160 isl9305_i2c_probe() error: buffer overflow 'pdata->init_data' 3 <= 3
Fixes: dec38b5ce6a9edb4 ("regulator: isl9305: Add Intersil ISL9305/H driver")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 591a3d7c09fa08baff48ad86c2347dbd28a52753 ]
0day testing by Fengguang Wu triggered this crash while running Trinity:
kernel BUG at include/linux/pagemap.h:151!
...
CPU: 0 PID: 458 Comm: trinity-c0 Not tainted 4.11.0-rc2-00251-g2947ba0 #1
...
Call Trace:
__get_user_pages_fast()
get_user_pages_fast()
get_futex_key()
futex_requeue()
do_futex()
SyS_futex()
do_syscall_64()
entry_SYSCALL64_slow_path()
It' VM_BUG_ON() due to false-negative in_atomic(). We call
page_cache_get_speculative() with disabled local interrupts.
It should be atomic enough.
So let's check for disabled interrupts in the VM_BUG_ON() condition
too, to resolve this.
( This got triggered by the conversion of the x86 GUP code to the
generic GUP code. )
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: LKP <lkp@01.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170324114709.pcytvyb3d6ajux33@black.fi.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb88a0588717ba6c756cb5972d75766b273a6817 upstream.
Corsair Strafe RGB keyboard does not respond to usb control messages
sometimes and hence generates timeouts.
Commit de3af5bf259d ("usb: quirks: add delay init quirk for Corsair
Strafe RGB keyboard") tried to fix those timeouts by adding
USB_QUIRK_DELAY_INIT.
Unfortunately, even with this quirk timeouts of usb_control_msg()
can still be seen, but with a lower frequency (approx. 1 out of 15):
[ 29.103520] usb 1-8: string descriptor 0 read error: -110
[ 34.363097] usb 1-8: can't set config #1, error -110
Adding further delays to different locations where usb control
messages are issued just moves the timeouts to other locations,
e.g.:
[ 35.400533] usbhid 1-8:1.0: can't add hid device: -110
[ 35.401014] usbhid: probe of 1-8:1.0 failed with error -110
The only way to reliably avoid those issues is having a pause after
each usb control message. In approx. 200 boot cycles no more timeouts
were seen.
Addionaly, keep USB_QUIRK_DELAY_INIT as it turned out to be necessary
to have the delay in hub_port_connect() after hub_port_init().
The overall boot time seems not to be influenced by these additional
delays, even on fast machines and lightweight distributions.
Fixes: de3af5bf259d ("usb: quirks: add delay init quirk for Corsair Strafe RGB keyboard")
Cc: stable@vger.kernel.org
Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f35157417215ec138c920320c746fdb3e04ef1d5 upstream.
Provide a function, kmemdup_nul(), that will create a NUL-terminated string
from an unterminated character array where the length is known in advance.
This is better than kstrndup() in situations where we already know the
string length as the strnlen() in kstrndup() is superfluous.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d9b3fca27385eafe61c3ca6feab6cb1e7dc77482 upstream.
tcp_hdrlen is wasteful if you already have a pointer to struct tcphdr.
This splits the size calculation into a helper function that can be
used if a struct tcphdr is already available.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 879626e3a52630316d817cbda7cec9a5446d1d82 ]
Note in the databook - Section 4.4 - EEE :
" The EEE feature is not supported when the MAC is configured to use the
TBI, RTBI, SMII, RMII or SGMII single PHY interface. Even if the MAC
supports multiple PHY interfaces, you should activate the EEE mode only
when the MAC is operating with GMII, MII, or RGMII interface."
Applying this restriction solves a stability issue observed on Amlogic
gxl platforms operating with RMII interface and the internal PHY.
Fixes: 83bf79b6bb64 ("stmmac: disable at run-time the EEE if not supported")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
