| Age | Commit message (Collapse) | Author |
|---|
|
commit 1123a6041654e8f889014659593bad4168e542c2 upstream.
Linu Cherian reported a WARN in cleanup_srcu_struct() when shutting
down a guest running iperf on a VFIO assigned device. This happens
because irqfd_wakeup() calls srcu_read_lock(&kvm->irq_srcu) in interrupt
context, while a worker thread does the same inside kvm_set_irq(). If the
interrupt happens while the worker thread is executing __srcu_read_lock(),
updates to the Classic SRCU ->lock_count[] field or the Tree SRCU
->srcu_lock_count[] field can be lost.
The docs say you are not supposed to call srcu_read_lock() and
srcu_read_unlock() from irq context, but KVM interrupt injection happens
from (host) interrupt context and it would be nice if SRCU supported the
use case. KVM is using SRCU here not really for the "sleepable" part,
but rather due to its IPI-free fast detection of grace periods. It is
therefore not desirable to switch back to RCU, which would effectively
revert commit 719d93cd5f5c ("kvm/irqchip: Speed up KVM_SET_GSI_ROUTING",
2014-01-16).
However, the docs are overly conservative. You can have an SRCU instance
only has users in irq context, and you can mix process and irq context
as long as process context users disable interrupts. In addition,
__srcu_read_unlock() actually uses this_cpu_dec() on both Tree SRCU and
Classic SRCU. For those two implementations, only srcu_read_lock()
is unsafe.
When Classic SRCU's __srcu_read_unlock() was changed to use this_cpu_dec(),
in commit 5a41344a3d83 ("srcu: Simplify __srcu_read_unlock() via
this_cpu_dec()", 2012-11-29), __srcu_read_lock() did two increments.
Therefore it kept __this_cpu_inc(), with preempt_disable/enable in
the caller. Tree SRCU however only does one increment, so on most
architectures it is more efficient for __srcu_read_lock() to use
this_cpu_inc(), and any performance differences appear to be down in
the noise.
Fixes: 719d93cd5f5c ("kvm/irqchip: Speed up KVM_SET_GSI_ROUTING")
Reported-by: Linu Cherian <linuc.decode@gmail.com>
Suggested-by: Linu Cherian <linuc.decode@gmail.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41c25707d21716826e3c1f60967f5550610ec1c9 upstream.
In most cases, a cgroup controller don't care about the liftimes of
cgroups. For the controller, a css becomes online when ->css_online()
is called on it and offline when ->css_offline() is called.
However, cpuset is special in that the user interface it exposes cares
whether certain cgroups exist or not. Combined with the RCU delay
between cgroup removal and css offlining, this can lead to user
visible behavior oddities where operations which should succeed after
cgroup removals fail for some time period. The effects of cgroup
removals are delayed when seen from userland.
This patch adds css_is_dying() which tests whether offline is pending
and updates is_cpuset_online() so that the function returns false also
while offline is pending. This gets rid of the userland visible
delays.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Link: http://lkml.kernel.org/r/327ca1f5-7957-fbb9-9e5f-9ba149d40ba2@oracle.com
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 33c35aa4817864e056fd772230b0c6b552e36ea2 upstream.
The kill_css() function may be called more than once under the condition
that the css was killed but not physically removed yet followed by the
removal of the cgroup that is hosting the css. This patch prevents any
harmm from being done when that happens.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c70d9d809fdeecedb96972457ee45c49a232d97f upstream.
When I introduced ptracer_cred I failed to consider the weirdness of
fork where the task_struct copies the old value by default. This
winds up leaving ptracer_cred set even when a process forks and
the child process does not wind up being ptraced.
Because ptracer_cred is not set on non-ptraced processes whose
parents were ptraced this has broken the ability of the enlightenment
window manager to start setuid children.
Fix this by properly initializing ptracer_cred in ptrace_init_task
This must be done with a little bit of care to preserve the current value
of ptracer_cred when ptrace carries through fork. Re-reading the
ptracer_cred from the ptracing process at this point is inconsistent
with how PT_PTRACE_CAP has been maintained all of these years.
Tested-by: Takashi Iwai <tiwai@suse.de>
Fixes: 64b875f7ac8a ("ptrace: Capture the ptracer's creds not PT_PTRACE_CAP")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 864b9a393dcb5aed09b8fd31b9bbda0fdda99374 upstream.
We have seen an early OOM killer invocation on ppc64 systems with
crashkernel=4096M:
kthreadd invoked oom-killer: gfp_mask=0x16040c0(GFP_KERNEL|__GFP_COMP|__GFP_NOTRACK), nodemask=7, order=0, oom_score_adj=0
kthreadd cpuset=/ mems_allowed=7
CPU: 0 PID: 2 Comm: kthreadd Not tainted 4.4.68-1.gd7fe927-default #1
Call Trace:
dump_stack+0xb0/0xf0 (unreliable)
dump_header+0xb0/0x258
out_of_memory+0x5f0/0x640
__alloc_pages_nodemask+0xa8c/0xc80
kmem_getpages+0x84/0x1a0
fallback_alloc+0x2a4/0x320
kmem_cache_alloc_node+0xc0/0x2e0
copy_process.isra.25+0x260/0x1b30
_do_fork+0x94/0x470
kernel_thread+0x48/0x60
kthreadd+0x264/0x330
ret_from_kernel_thread+0x5c/0xa4
Mem-Info:
active_anon:0 inactive_anon:0 isolated_anon:0
active_file:0 inactive_file:0 isolated_file:0
unevictable:0 dirty:0 writeback:0 unstable:0
slab_reclaimable:5 slab_unreclaimable:73
mapped:0 shmem:0 pagetables:0 bounce:0
free:0 free_pcp:0 free_cma:0
Node 7 DMA free:0kB min:0kB low:0kB high:0kB active_anon:0kB inactive_anon:0kB active_file:0kB inactive_file:0kB unevictable:0kB isolated(anon):0kB isolated(file):0kB present:52428800kB managed:110016kB mlocked:0kB dirty:0kB writeback:0kB mapped:0kB shmem:0kB slab_reclaimable:320kB slab_unreclaimable:4672kB kernel_stack:1152kB pagetables:0kB unstable:0kB bounce:0kB free_pcp:0kB local_pcp:0kB free_cma:0kB writeback_tmp:0kB pages_scanned:0 all_unreclaimable? yes
lowmem_reserve[]: 0 0 0 0
Node 7 DMA: 0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB 0*8192kB 0*16384kB = 0kB
0 total pagecache pages
0 pages in swap cache
Swap cache stats: add 0, delete 0, find 0/0
Free swap = 0kB
Total swap = 0kB
819200 pages RAM
0 pages HighMem/MovableOnly
817481 pages reserved
0 pages cma reserved
0 pages hwpoisoned
the reason is that the managed memory is too low (only 110MB) while the
rest of the the 50GB is still waiting for the deferred intialization to
be done. update_defer_init estimates the initial memoty to initialize
to 2GB at least but it doesn't consider any memory allocated in that
range. In this particular case we've had
Reserving 4096MB of memory at 128MB for crashkernel (System RAM: 51200MB)
so the low 2GB is mostly depleted.
Fix this by considering memblock allocations in the initial static
initialization estimation. Move the max_initialise to
reset_deferred_meminit and implement a simple memblock_reserved_memory
helper which iterates all reserved blocks and sums the size of all that
start below the given address. The cumulative size is than added on top
of the initial estimation. This is still not ideal because
reset_deferred_meminit doesn't consider holes and so reservation might
be above the initial estimation whihch we ignore but let's make the
logic simpler until we really need to handle more complicated cases.
Fixes: 3a80a7fa7989 ("mm: meminit: initialise a subset of struct pages if CONFIG_DEFERRED_STRUCT_PAGE_INIT is set")
Link: http://lkml.kernel.org/r/20170531104010.GI27783@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Tested-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a291a7c9428155e8e623e4a3989f8be47134df5 upstream.
KVM uses get_user_pages() to resolve its stage2 faults. KVM sets the
FOLL_HWPOISON flag causing faultin_page() to return -EHWPOISON when it
finds a VM_FAULT_HWPOISON. KVM handles these hwpoison pages as a
special case. (check_user_page_hwpoison())
When huge pages are involved, this doesn't work so well.
get_user_pages() calls follow_hugetlb_page(), which stops early if it
receives VM_FAULT_HWPOISON from hugetlb_fault(), eventually returning
-EFAULT to the caller. The step to map this to -EHWPOISON based on the
FOLL_ flags is missing. The hwpoison special case is skipped, and
-EFAULT is returned to user-space, causing Qemu or kvmtool to exit.
Instead, move this VM_FAULT_ to errno mapping code into a header file
and use it from faultin_page() and follow_hugetlb_page().
With this, KVM works as expected.
This isn't a problem for arm64 today as we haven't enabled
MEMORY_FAILURE, but I can't see any reason this doesn't happen on x86
too, so I think this should be a fix. This doesn't apply earlier than
stable's v4.11.1 due to all sorts of cleanup.
[james.morse@arm.com: add vm_fault_to_errno() call to faultin_page()]
suggested.
Link: http://lkml.kernel.org/r/20170525171035.16359-1-james.morse@arm.com
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20170524160900.28786-1-james.morse@arm.com
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 35d2f80b07bbe03fb358afb0bdeff7437a7d67ff ]
It appears that TCP checksum offloading has been broken for
Q-in-Q vlans. The behavior was execerbated by the
series
commit afb0bc972b52 ("Merge branch 'stacked_vlan_tso'")
that that enabled accleleration features on stacked vlans.
However, event without that series, it is possible to trigger
this issue. It just requires a lot more specialized configuration.
The root cause is the interaction between how
netdev_intersect_features() works, the features actually set on
the vlan devices and HW having the ability to run checksum with
longer headers.
The issue starts when netdev_interesect_features() replaces
NETIF_F_HW_CSUM with a combination of NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM,
if the HW advertises IP|IPV6 specific checksums. This happens
for tagged and multi-tagged packets. However, HW that enables
IP|IPV6 checksum offloading doesn't gurantee that packets with
arbitrarily long headers can be checksummed.
This patch disables IP|IPV6 checksums on the packet for multi-tagged
packets.
CC: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
CC: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 73dd3a4839c1d27c36d4dcc92e1ff44225ecbeb7 ]
Currently when firmware command gets stuck or it takes long time to
complete, the driver command will get timeout and the command slot is
freed and can be used for new commands, and if the firmware receive new
command on the old busy slot its behavior is unexpected and this could
be harmful.
To fix this when the driver command gets timeout we return failure,
but we don't free the command slot and we wait for the firmware to
explicitly respond to that command.
Once all the entries are busy we will stop processing new firmware
commands.
Fixes: 9cba4ebcf374 ('net/mlx5: Fix potential deadlock in command mode change')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 30e7d894c1478c88d50ce94ddcdbd7f9763d9cdd upstream.
Enabling the tracer selftest triggers occasionally the warning in
text_poke(), which warns when the to be modified page is not marked
reserved.
The reason is that the tracer selftest installs kprobes on functions marked
__init for testing. These probes are removed after the tests, but that
removal schedules the delayed kprobes_optimizer work, which will do the
actual text poke. If the work is executed after the init text is freed,
then the warning triggers. The bug can be reproduced reliably when the work
delay is increased.
Flush the optimizer work and wait for the optimizing/unoptimizing lists to
become empty before returning from the kprobes tracer selftest. That
ensures that all operations which were queued due to the probes removal
have completed.
Link: http://lkml.kernel.org/r/20170516094802.76a468bb@gandalf.local.home
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Fixes: 6274de498 ("kprobes: Support delayed unoptimizing")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d9854eaea776441b38a9a45b4e6879524c4f48c upstream.
This change undo the change done by 'commit 3bec24747446
("iio: hid-sensor-trigger: Change get poll value function order to avoid
sensor properties losing after resume from S3")' as this breaks some
USB/i2c sensor hubs.
Instead of relying on HW for restoring poll and hysteresis, driver stores
and restores on resume (S3). In this way user space modified settings are
not lost for any kind of sensor hub behavior.
In this change, whenever user space modifies sampling frequency or
hysteresis driver will get the feature value from the hub and store in the
per device hid_sensor_common data structure. On resume callback from S3,
system will set the feature to sensor hub, if user space ever modified the
feature value.
Fixes: 3bec24747446 ("iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3")
Reported-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Song, Hongyan <hongyan.song@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit deccf497d804a4c5fca2dbfad2f104675a6f9102 upstream.
stat/lstat/fstatat need to pass AT_NO_AUTOMOUNT to vfs_statx() as the
pre-statx code didn't set LOOKUP_AUTOMOUNT, even though fstatat() accepted
the AT_NO_AUTOMOUNT flag.
Fixes: a528d35e8bfc ("statx: Add a system call to make enhanced file info available")
Reported-by: Ian Kent <raven@themaw.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4636e70bb0a8b871998b6841a2e4b205cf2bc863 upstream.
Patch series "mm,dax: Fix data corruption due to mmap inconsistency",
v4.
This series fixes data corruption that can happen for DAX mounts when
page faults race with write(2) and as a result page tables get out of
sync with block mappings in the filesystem and thus data seen through
mmap is different from data seen through read(2).
The series passes testing with t_mmap_stale test program from Ross and
also other mmap related tests on DAX filesystem.
This patch (of 4):
dax_invalidate_mapping_entry() currently removes DAX exceptional entries
only if they are clean and unlocked. This is done via:
invalidate_mapping_pages()
invalidate_exceptional_entry()
dax_invalidate_mapping_entry()
However, for page cache pages removed in invalidate_mapping_pages()
there is an additional criteria which is that the page must not be
mapped. This is noted in the comments above invalidate_mapping_pages()
and is checked in invalidate_inode_page().
For DAX entries this means that we can can end up in a situation where a
DAX exceptional entry, either a huge zero page or a regular DAX entry,
could end up mapped but without an associated radix tree entry. This is
inconsistent with the rest of the DAX code and with what happens in the
page cache case.
We aren't able to unmap the DAX exceptional entry because according to
its comments invalidate_mapping_pages() isn't allowed to block, and
unmap_mapping_range() takes a write lock on the mapping->i_mmap_rwsem.
Since we essentially never have unmapped DAX entries to evict from the
radix tree, just remove dax_invalidate_mapping_entry().
Fixes: c6dcf52c23d2 ("mm: Invalidate DAX radix tree entries only if appropriate")
Link: http://lkml.kernel.org/r/20170510085419.27601-2-jack@suse.cz
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: Jan Kara <jack@suse.cz>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a2e48854d704214dac7546e87ae0e4daa0e61a0 upstream.
Since commit 59dc76b0d4df ("mm: vmscan: reduce size of inactive file
list") we noticed bigger IO spikes during changes in cache access
patterns.
The patch in question shrunk the inactive list size to leave more room
for the current workingset in the presence of streaming IO. However,
workingset transitions that previously happened on the inactive list are
now pushed out of memory and incur more refaults to complete.
This patch disables active list protection when refaults are being
observed. This accelerates workingset transitions, and allows more of
the new set to establish itself from memory, without eating into the
ability to protect the established workingset during stable periods.
The workloads that were measurably affected for us were hit pretty bad
by it, with refault/majfault rates doubling and tripling during cache
transitions, and the machines sustaining half-hour periods of 100% IO
utilization, where they'd previously have sub-minute peaks at 60-90%.
Stateful services that handle user data tend to be more conservative
with kernel upgrades. As a result we hit most page cache issues with
some delay, as was the case here.
The severity seemed to warrant a stable tag.
Fixes: 59dc76b0d4df ("mm: vmscan: reduce size of inactive file list")
Link: http://lkml.kernel.org/r/20170404220052.27593-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e335d9e7ddbcf83d03e7fbe65797ebed2272c18 upstream.
This reverts commit bbd6411513aa8ef3ea02abab61318daf87c1af1e.
I've been sitting on this revert for too long and it unfortunately
missed 4.11. It's also the reason why I haven't merged ring-based
dirty tracking for 4.12.
Using kvm_vcpu_memslots in kvm_gfn_to_hva_cache_init and
kvm_vcpu_write_guest_offset_cached means that the MSR value can
now be used to access SMRAM, simply by making it point to an SMRAM
physical address. This is problematic because it lets the guest
OS overwrite memory that it shouldn't be able to touch.
Fixes: bbd6411513aa8ef3ea02abab61318daf87c1af1e
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 19b7ccf8651df09d274671b53039c672a52ad84d upstream.
Commit 25520d55cdb6 ("block: Inline blk_integrity in struct gendisk")
introduced blk_integrity_revalidate(), which seems to assume ownership
of the stable pages flag and unilaterally clears it if no blk_integrity
profile is registered:
if (bi->profile)
disk->queue->backing_dev_info->capabilities |=
BDI_CAP_STABLE_WRITES;
else
disk->queue->backing_dev_info->capabilities &=
~BDI_CAP_STABLE_WRITES;
It's called from revalidate_disk() and rescan_partitions(), making it
impossible to enable stable pages for drivers that support partitions
and don't use blk_integrity: while the call in revalidate_disk() can be
trivially worked around (see zram, which doesn't support partitions and
hence gets away with zram_revalidate_disk()), rescan_partitions() can
be triggered from userspace at any time. This breaks rbd, where the
ceph messenger is responsible for generating/verifying CRCs.
Since blk_integrity_{un,}register() "must" be used for (un)registering
the integrity profile with the block layer, move BDI_CAP_STABLE_WRITES
setting there. This way drivers that call blk_integrity_register() and
use integrity infrastructure won't interfere with drivers that don't
but still want stable pages.
Fixes: 25520d55cdb6 ("block: Inline blk_integrity in struct gendisk")
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9dd46188edc2f0d1f37328637860bb65a771124 upstream.
F2FS uses 4 bytes to represent block address. As a result, supported
size of disk is 16 TB and it equals to 16 * 1024 * 1024 / 2 segments.
Signed-off-by: Jin Qian <jinqian@google.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Ethernet link on an interrupt driven PHY was not coming up if the Ethernet
cable was plugged before the Ethernet interface was brought up.
The patch trigger PHY state machine to update link state if PHY was requested to
do auto-negotiation and auto-negotiation complete flag already set.
During power-up cycle the PHY do auto-negotiation, generate interrupt and set
auto-negotiation complete flag. Interrupt is handled by PHY state machine but
doesn't update link state because PHY is in PHY_READY state. After some time
MAC bring up, start and request PHY to do auto-negotiation. If there are no new
settings to advertise genphy_config_aneg() doesn't start PHY auto-negotiation.
PHY continue to stay in auto-negotiation complete state and doesn't fire
interrupt. At the same time PHY state machine expect that PHY started
auto-negotiation and is waiting for interrupt from PHY and it won't get it.
Fixes: 321beec5047a ("net: phy: Use interrupts when available in NOLINK state")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Cc: stable <stable@vger.kernel.org> # v4.9+
Tested-by: Roger Quadros <rogerq@ti.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Certain 64-bit systems (e.g. Amlogic Meson GX) require buffers to be
used for DMA to be 8-byte-aligned. struct sdio_func has an embedded
small DMA buffer not meeting this requirement.
When testing switching to descriptor chain mode in meson-gx driver
SDIO is broken therefore. Fix this by allocating the small DMA buffer
separately as kmalloc ensures that the returned memory area is
properly aligned for every basic data type.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Again, a batch that's been sitting a couple of weeks, mostly because
I anticipated a bit more material but it didn't show up -- which is
good.
These are all your garden variety fixes for ARM platforms.
The most visible issue fixed here is probably the SMP reset issue on
OMAP, the rest are minor stuff"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: allwinner: a64: add pmu0 regs for USB PHY
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
reset: add exported __reset_control_get, return NULL if optional
ARM: orion5x: only call into phylib when available
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
ARM: sun8i: a33: add operating-points-v2 property to all nodes
ARM: sun8i: a33: remove highest OPP to fix CPU crashes
|
|
Pull block fixes from Jens Axboe:
"Four small fixes.
Three of them fix the same error in NVMe, in loop, fc, and rdma
respectively. The last fix from Ming fixes a regression in this
series, where our bvec gap logic was wrong and causes an oops on
NVMe for certain conditions"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix bio_will_gap() for first bvec with offset
nvme-fc: Fix sqsize wrong assignment based on ctrl MQES capability
nvme-rdma: Fix sqsize wrong assignment based on ctrl MQES capability
nvme-loop: Fix sqsize wrong assignment based on ctrl MQES capability
|
|
Pull networking fixes from David Miller:
"Things seem to be settling down as far as networking is concerned,
let's hope this trend continues...
1) Add iov_iter_revert() and use it to fix the behavior of
skb_copy_datagram_msg() et al., from Al Viro.
2) Fix the protocol used in the synthetic SKB we cons up for the
purposes of doing a simulated route lookup for RTM_GETROUTE
requests. From Florian Larysch.
3) Don't add noop_qdisc to the per-device qdisc hashes, from Cong
Wang.
4) Don't call netdev_change_features with the team lock held, from
Xin Long.
5) Revert TCP F-RTO extension to catch more spurious timeouts because
it interacts very badly with some middle-boxes. From Yuchung
Cheng.
6) Fix the loss of error values in l2tp {s,g}etsockopt calls, from
Guillaume Nault.
7) ctnetlink uses bit positions where it should be using bit masks,
fix from Liping Zhang.
8) Missing RCU locking in netfilter helper code, from Gao Feng.
9) Avoid double frees and use-after-frees in tcp_disconnect(), from
Eric Dumazet.
10) Don't do a changelink before we register the netdevice in
bridging, from Ido Schimmel.
11) Lock the ipv6 device address list properly, from Rabin Vincent"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
netfilter: ipt_CLUSTERIP: Fix wrong conntrack netns refcnt usage
netfilter: nft_hash: do not dump the auto generated seed
drivers: net: usb: qmi_wwan: add QMI_QUIRK_SET_DTR for Telit PID 0x1201
ipv6: Fix idev->addr_list corruption
net: xdp: don't export dev_change_xdp_fd()
bridge: netlink: register netdevice before executing changelink
bridge: implement missing ndo_uninit()
bpf: reference may_access_skb() from __bpf_prog_run()
tcp: clear saved_syn in tcp_disconnect()
netfilter: nf_ct_expect: use proper RCU list traversal/update APIs
netfilter: ctnetlink: skip dumping expect when nfct_help(ct) is NULL
netfilter: make it safer during the inet6_dev->addr_list traversal
netfilter: ctnetlink: make it safer when checking the ct helper name
netfilter: helper: Add the rcu lock when call __nf_conntrack_helper_find
netfilter: ctnetlink: using bit to represent the ct event
netfilter: xt_TCPMSS: add more sanity tests on tcph->doff
net: tcp: Increase TCP_MIB_OUTRSTS even though fail to alloc skb
l2tp: don't mask errors in pppol2tp_getsockopt()
l2tp: don't mask errors in pppol2tp_setsockopt()
tcp: restrict F-RTO to work-around broken middle-boxes
...
|
|
Commit 729204ef49ec("block: relax check on sg gap") allows us to merge
bios, if both are physically contiguous. This change can merge a huge
number of small bios, through mkfs for example, mkfs.ntfs running time
can be decreased to ~1/10.
But if one rq starts with a non-aligned buffer (the 1st bvec's bv_offset
is non-zero) and if we allow the merge, it is quite difficult to respect
sg gap limit, especially the max segment size, or we risk having an
unaligned virtual boundary. This patch tries to avoid the issue by
disallowing a merge, if the req starts with an unaligned buffer.
Also add comments to explain why the merged segment can't end in
unaligned virt boundary.
Fixes: 729204ef49ec ("block: relax check on sg gap")
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Rewrote parts of the commit message and comments.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Pull virtio fixes from Michael S. Tsirkin:
"virtio oops fixes
The virtio pci rework using shared interrupts caused a lot of issues.
We tried to fix them but run out of time. Revert for now, and revisit
the issue for the next kernel.
Luckily we are able to do this without loosing automatic interrupt
NUMA affinity which was the main motivator for the rework"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-pci: Remove affinity hint before freeing the interrupt
Revert "virtio_pci: remove struct virtio_pci_vq_info"
Revert "virtio_pci: use shared interrupts for virtqueues"
Revert "virtio_pci: don't duplicate the msix_enable flag in struct pci_dev"
Revert "virtio_pci: simplify MSI-X setup"
Revert "virtio_pci: fix out of bound access for msix_names"
MAINTAINERS: fix virtio file pattern
virtio_console: fix uninitialized variable use
virtio_net: clear MTU when out of range
virtio: allow drivers to validate features
virtio_net: enable big packets for large MTU values
|
|
Dave noticed that after fixing MADV_DONTNEED vs numa balancing race the
last pmdp_huge_get_and_clear_notify() user is gone.
Let's drop the helper.
Link: http://lkml.kernel.org/r/20170306112047.24809-1-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"This contains fixes for two long standing subtle bugs:
- kthread_bind() on a new kthread binds it to specific CPUs and
prevents userland from messing with the affinity or cgroup
membership. Unfortunately, for cgroup membership, there's a window
between kthread creation and kthread_bind*() invocation where the
kthread can be moved into a non-root cgroup by userland.
Depending on what controllers are in effect, this can assign the
kthread unexpected attributes. For example, in the reported case,
workqueue workers ended up in a non-root cpuset cgroups and had
their CPU affinities overridden. This broke workqueue invariants
and led to workqueue stalls.
Fixed by closing the window between kthread creation and
kthread_bind() as suggested by Oleg.
- There was a bug in cgroup mount path which could allow two
competing mount attempts to attach the same cgroup_root to two
different superblocks.
This was caused by mishandling return value from kernfs_pin_sb().
Fixed"
* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: avoid attaching a cgroup root to two different superblocks
cgroup, kthread: close race window where new kthreads can be migrated to non-root cgroups
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull VFS fixes from Al Viro:
"statx followup fixes and a fix for stack-smashing on alpha"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
alpha: fix stack smashing in old_adjtimex(2)
statx: Include a mask for stx_attributes in struct statx
statx: Reserve the top bit of the mask for future struct expansion
xfs: report crtime and attribute flags to statx
ext4: Add statx support
statx: optimize copy of struct statx to userspace
statx: remove incorrect part of vfs_statx() comment
statx: reject unknown flags when using NULL path
Documentation/filesystems: fix documentation for ->getattr()
|
|
Pull block fixes from Jens Axboe:
"Here's a pull request for 4.11-rc, fixing a set of issues mostly
centered around the new scheduling framework. These have been brewing
for a while, but split up into what we absolutely need in 4.11, and
what we can defer until 4.12. These are well tested, on both single
queue and multiqueue setups, and with and without shared tags. They
fix several hangs that have happened in testing.
This is obviously larger than I would have preferred at this point in
time, but I don't think we can shave much off this and still get the
desired results.
In detail, this pull request contains:
- a set of five fixes for NVMe, mostly from Christoph and one from
Roland.
- a series from Bart, fixing issues with dm-mq and SCSI shared tags
and scheduling. Note that one of those patches commit messages may
read like an optimization, but it is in fact an important fix for
queue restarts in particular.
- a series from Omar, most importantly fixing a hang with multiple
hardware queues when we fail to get a driver tag. Another important
fix in there is for resizing hardware queues, which nbd does when
handling multiple sockets for one connection.
- fixing an imbalance in putting the ctx for hctx request allocations
from Minchan"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: Restart a single queue if tag sets are shared
dm rq: Avoid that request processing stalls sporadically
scsi: Avoid that SCSI queues get stuck
blk-mq: Introduce blk_mq_delay_run_hw_queue()
blk-mq: remap queues when adding/removing hardware queues
blk-mq-sched: fix crash in switch error path
blk-mq-sched: set up scheduler tags when bringing up new queues
blk-mq-sched: refactor scheduler initialization
blk-mq: use the right hctx when getting a driver tag fails
nvmet: fix byte swap in nvmet_parse_io_cmd
nvmet: fix byte swap in nvmet_execute_write_zeroes
nvmet: add missing byte swap in nvmet_get_smart_log
nvme: add missing byte swap in nvme_setup_discard
nvme: Correct NVMF enum values to match NVMe-oF rev 1.0
block: do not put mq context in blk_mq_alloc_request_hctx
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fix from Linus Walleij:
"This late fix for pin control is hopefully the last I send this cycle.
The problem was detected early in the v4.11 release cycle and there
has been some back and forth on how to solve it. Sadly the proper fix
arrives late, but at least not too late.
An issue was detected with pin control on the Freescale i.MX after the
refactorings for more general group and function handling.
We now have the proper fix for this"
* tag 'pinctrl-v4.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: core: Fix pinctrl_register_and_init() with pinctrl_enable()
|
|
Pull KVM fixes from Radim Krčmář:
"ARM:
- Fix a problem with GICv3 userspace save/restore
- Clarify GICv2 userspace save/restore ABI
- Be more careful in clearing GIC LRs
- Add missing synchronization primitive to our MMU handling code
PPC:
- Check for a NULL return from kzalloc
s390:
- Prevent translation exception errors on valid page tables for the
instruction-exection-protection support
x86:
- Fix Page-Modification Logging when running a nested guest"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Check for kmalloc errors in ioctl
KVM: nVMX: initialize PML fields in vmcs02
KVM: nVMX: do not leak PML full vmexit to L1
KVM: arm/arm64: vgic: Fix GICC_PMR uaccess on GICv3 and clarify ABI
KVM: arm64: Ensure LRs are clear when they should be
kvm: arm/arm64: Fix locking for kvm_free_stage2_pgd
KVM: s390: remove change-recording override support
arm/arm64: KVM: Take mmap_sem in kvm_arch_prepare_memory_region
arm/arm64: KVM: Take mmap_sem in stage2_unmap_vm
|
|
into fixes
Reset controller fixes for v4.11
Fix devm_reset_controller_get_optional to return NULL for non-DT devices,
if the RESET_CONTROLLER Kconfig option is enabled. This fixes probe failures
of the 8250_dw driver on Intel platforms after commit acbdad8dd1ab ("serial:
8250_dw: simplify optional reset handling").
* tag 'reset-fixes-for-4.11-2' of git://git.pengutronix.de/git/pza/linux:
reset: add exported __reset_control_get, return NULL if optional
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
To improve scalability, if hardware queues are shared, restart
a single hardware queue in round-robin fashion. Rename
blk_mq_sched_restart_queues() to reflect the new semantics.
Remove blk_mq_sched_mark_restart_queue() because this function
has no callers. Remove flag QUEUE_FLAG_RESTART because this
patch removes the code that uses this flag.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Introduce a function that runs a hardware queue unconditionally
after a delay. Note: there is already a function that stops and
restarts a hardware queue after a delay, namely blk_mq_delay_queue().
This function will be used in the next patch in this series.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Long Li <longli@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
In elevator_switch(), if blk_mq_init_sched() fails, we attempt to fall
back to the original scheduler. However, at this point, we've already
torn down the original scheduler's tags, so this causes a crash. Doing
the fallback like the legacy elevator path is much harder for mq, so fix
it by just falling back to none, instead.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Some drivers can't support all features in all configurations. At the
moment we blindly set FEATURES_OK and later FAILED. Support this better
by adding a callback drivers can use to do some early checks.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Recent pinctrl changes to allow dynamic allocation of pins exposed one
more issue with the pinctrl pins claimed early by the controller itself.
This caused a regression for IMX6 pinctrl hogs.
Before enabling the pin controller driver we need to wait until it has
been properly initialized, then claim the hogs, and only then enable it.
To fix the regression, split the code into pinctrl_claim_hogs() and
pinctrl_enable(). And then let's require that pinctrl_enable() is always
called by the pin controller driver when ready after calling
pinctrl_register_and_init().
Depends-on: 950b0d91dc10 ("pinctrl: core: Fix regression caused by delayed
work for hogs")
Fixes: df61b366af26 ("pinctrl: core: Use delayed work for hogs")
Fixes: e566fc11ea76 ("pinctrl: imx: use generic pinctrl helpers for
managing groups")
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD bug fix from Lee Jones:
"Increase buffer size om cros-ec to allow for SPI messages"
* tag 'mfd-fixes-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: cros-ec: Fix host command buffer size
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
From: Christoffer Dall <cdall@linaro.org>
KVM/ARM Fixes for v4.11-rc6
Fixes include:
- Fix a problem with GICv3 userspace save/restore
- Clarify GICv2 userspace save/restore ABI
- Be more careful in clearing GIC LRs
- Add missing synchronization primitive to our MMU handling code
|
|
For SPI, we can get up to 32 additional bytes for response preamble.
The current overhead (2 bytes) may cause problems when we try to receive
a big response. Update it to 32 bytes.
Without this fix we could see a kernel BUG when we receive a big response
from the Chrome EC when is connected via SPI.
Signed-off-by: Vic Yang <victoryang@google.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo.collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Rename the internal __reset_control_get/put functions to
__reset_control_get/put_internal and add an exported
__reset_control_get equivalent to __of_reset_control_get
that takes a struct device parameter.
This avoids the confusing call to __of_reset_control_get in
the non-DT case and fixes the devm_reset_control_get_optional
function to return NULL if RESET_CONTROLLER is enabled but
dev->of_node == NULL.
Fixes: bb475230b8e5 ("reset: make optional functions really optional")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ramiro Oliveira <Ramiro.Oliveira@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
As an oversight, for GICv2, we accidentally export the GICC_PMR register
in the format of the GICH_VMCR.VMPriMask field in the lower 5 bits of a
word, meaning that userspace must always use the lower 5 bits to
communicate with the KVM device and must shift the value left by 3
places to obtain the actual priority mask level.
Since GICv3 supports the full 8 bits of priority masking in the ICH_VMCR,
we have to fix the value we export when emulating a GICv2 on top of a
hardware GICv3 and exporting the emulated GICv2 state to userspace.
Take the chance to clarify this aspect of the ABI.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
|
|
Include a mask in struct stat to indicate which bits of stx_attributes the
filesystem actually supports.
This would also be useful if we add another system call that allows you to
do a 'bulk attribute set' and pass in a statx struct with the masks
appropriately set to say what you want to set.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"This update provides:
- make the scheduler clock switch to unstable mode smooth so the
timestamps stay at microseconds granularity instead of switching to
tick granularity.
- unbreak perf test tsc by taking the new offset into account which
was added in order to proveide better sched clock continuity
- switching sched clock to unstable mode runs all clock related
computations which affect the sched clock output itself from a work
queue. In case of preemption sched clock uses half updated data and
provides wrong timestamps. Keep the math in the protected context
and delegate only the static key switch to workqueue context.
- remove a duplicate header include"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/headers: Remove duplicate #include <linux/sched/debug.h> line
sched/clock: Fix broken stable to unstable transfer
sched/clock, x86/perf: Fix "perf test tsc"
sched/clock: Fix clear_sched_clock_stable() preempt wobbly
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two small fixes for the new CLKEVT_OF infrastructure"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
vmlinux.lds: Add __clkevt_of_table to kernel
clockevents: Fix syntax error in clkevt-of macro
|
|
opposite to iov_iter_advance(); the caller is responsible for never
using it to move back past the initial position.
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The enum values for QPTYPE, PRTYPE and CMS are off by 1 from the
values defined in figure 42 of the NVM Express over Fabrics 1.0:
http://www.nvmexpress.org/wp-content/uploads/NVMe_over_Fabrics_1_0_Gold_20160605-1.pdf
Fix our enums to match the final spec.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Disable kasan after the first report. There are several reasons for
this:
- Single bug quite often has multiple invalid memory accesses causing
storm in the dmesg.
- Write OOB access might corrupt metadata so the next report will print
bogus alloc/free stacktraces.
- Reports after the first easily could be not bugs by itself but just
side effects of the first one.
Given that multiple reports usually only do harm, it makes sense to
disable kasan after the first one. If user wants to see all the
reports, the boot-time parameter kasan_multi_shot must be used.
[aryabinin@virtuozzo.com: wrote changelog and doc, added missing include]
Link: http://lkml.kernel.org/r/20170323154416.30257-1-aryabinin@virtuozzo.com
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Huge pages are accounted as single units in the memcg's "file_mapped"
counter. Account the correct number of base pages, like we do in the
corresponding node counter.
Link: http://lkml.kernel.org/r/20170322005111.3156-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: <stable@vger.kernel.org> [4.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Yang Li has reported that drain_all_pages triggers a WARN_ON which means
that this function is called earlier than the mm_percpu_wq is
initialized on arm64 with CMA configured:
WARNING: CPU: 2 PID: 1 at mm/page_alloc.c:2423 drain_all_pages+0x244/0x25c
Modules linked in:
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.11.0-rc1-next-20170310-00027-g64dfbc5 #127
Hardware name: Freescale Layerscape 2088A RDB Board (DT)
task: ffffffc07c4a6d00 task.stack: ffffffc07c4a8000
PC is at drain_all_pages+0x244/0x25c
LR is at start_isolate_page_range+0x14c/0x1f0
[...]
drain_all_pages+0x244/0x25c
start_isolate_page_range+0x14c/0x1f0
alloc_contig_range+0xec/0x354
cma_alloc+0x100/0x1fc
dma_alloc_from_contiguous+0x3c/0x44
atomic_pool_init+0x7c/0x208
arm64_dma_init+0x44/0x4c
do_one_initcall+0x38/0x128
kernel_init_freeable+0x1a0/0x240
kernel_init+0x10/0xfc
ret_from_fork+0x10/0x20
Fix this by moving the whole setup_vmstat which is an initcall right now
to init_mm_internals which will be called right after the WQ subsystem
is initialized.
Link: http://lkml.kernel.org/r/20170315164021.28532-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Yang Li <pku.leo@gmail.com>
Tested-by: Yang Li <pku.leo@gmail.com>
Tested-by: Xiaolong Ye <xiaolong.ye@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull KVM fixes from Paolo Bonzini:
"All x86-specific, apart from some arch-independent syzkaller fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: cleanup the page tracking SRCU instance
KVM: nVMX: fix nested EPT detection
KVM: pci-assign: do not map smm memory slot pages in vt-d page tables
KVM: kvm_io_bus_unregister_dev() should never fail
KVM: VMX: Fix enable VPID conditions
KVM: nVMX: Fix nested VPID vmx exec control
KVM: x86: correct async page present tracepoint
kvm: vmx: Flush TLB when the APIC-access address changes
KVM: x86: use pic/ioapic destructor when destroy vm
KVM: x86: check existance before destroy
KVM: x86: clear bus pointer when destroyed
KVM: Documentation: document MCE ioctls
KVM: nVMX: don't reset kvm mmu twice
PTP: fix ptr_ret.cocci warnings
kvm: fix usage of uninit spinlock in avic_vm_destroy()
KVM: VMX: downgrade warning on unexpected exit code
|
