| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 259714100d98b50bf04d36a21bf50ca8b829fc11 ]
When the dedicated wake IRQ is level trigger, and it uses the
device's low-power status as the wakeup source, that means if the
device is not in low-power state, the wake IRQ will be triggered
if enabled; For this case, need enable the wake IRQ after running
the device's ->runtime_suspend() which make it enter low-power state.
e.g.
Assume the wake IRQ is a low level trigger type, and the wakeup
signal comes from the low-power status of the device.
The wakeup signal is low level at running time (0), and becomes
high level when the device enters low-power state (runtime_suspend
(1) is called), a wakeup event at (2) make the device exit low-power
state, then the wakeup signal also becomes low level.
------------------
| ^ ^|
---------------- | | --------------
|<---(0)--->|<--(1)--| (3) (2) (4)
if enable the wake IRQ before running runtime_suspend during (0),
a wake IRQ will arise, it causes resume immediately;
it works if enable wake IRQ ( e.g. at (3) or (4)) after running
->runtime_suspend().
This patch introduces a new status WAKE_IRQ_DEDICATED_REVERSE to
optionally support enabling wake IRQ after running ->runtime_suspend().
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 8527beb12087 ("PM: sleep: wakeirq: fix wake irq arming")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 19198e4ec97dc9d173b458a75ace3c3ca55c2d85 ]
This patch fixes all the qed and qede kernel-doc warnings
according to the guidelines that are described in
Documentation/doc-guide/kernel-doc.rst.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: e346e231b42b ("qed: Fix scheduling in a tasklet while getting stats")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Upstream commit: fb3bd914b3ec28f5fb697ac55c4846ac2d542855
Add a mitigation for the speculative return address stack overflow
vulnerability found on AMD processors.
The mitigation works by ensuring all RET instructions speculate to
a controlled location, similar to how speculation is controlled in the
retpoline sequence. To accomplish this, the __x86_return_thunk forces
the CPU to mispredict every function return using a 'safe return'
sequence.
To ensure the safety of this mitigation, the kernel must ensure that the
safe return sequence is itself free from attacker interference. In Zen3
and Zen4, this is accomplished by creating a BTB alias between the
untraining function srso_untrain_ret_alias() and the safe return
function srso_safe_ret_alias() which results in evicting a potentially
poisoned BTB entry and using that safe one for all function returns.
In older Zen1 and Zen2, this is accomplished using a reinterpretation
technique similar to Retbleed one: srso_untrain_ret() and
srso_safe_ret().
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit af80602799681c78f14fbe20b6185a56020dedee upstream.
In order to allow using mm_alloc() much earlier, move initializing
mm_cachep into mm_init().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20221025201057.751153381@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3f4c8211d982099be693be9aa7d6fc4607dff290 upstream.
Instead of duplicating init_mm, allocate a fresh mm. The advantage is
that mm_alloc() has much simpler dependencies. Additionally it makes
more conceptual sense, init_mm has no (and must not have) user state
to duplicate.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20221025201057.816175235@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7725acaa4f0c04fbefb0e0d342635b967bb7d414 upstream
check_bugs() has become a dumping ground for all sorts of activities to
finalize the CPU initialization before running the rest of the init code.
Most are empty, a few do actual bug checks, some do alternative patching
and some cobble a CPU advertisement string together....
Aside of that the current implementation requires duplicated function
declaration and mostly empty header files for them.
Provide a new function arch_cpu_finalize_init(). Provide a generic
declaration if CONFIG_ARCH_HAS_CPU_FINALIZE_INIT is selected and a stub
inline otherwise.
This requires a temporary #ifdef in start_kernel() which will be removed
along with check_bugs() once the architectures are converted over.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230613224544.957805717@linutronix.de
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 211db0ac9e3dc6c46f2dd53395b34d76af929faf ]
Since vfs_path_lookup is exported, It should not be internal.
Move vfs_path_lookup prototype in internal.h to linux/namei.h.
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Stable-dep-of: df9d70c18616 ("cifs: if deferred close is disabled then close files immediately")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 88da4e8113110d5f4ebdd2f8cd0899e300cd1954 upstream.
The devm_pwmchip_add() can be called by a module that optionally
instantiates PWM chip. In the case of CONFIG_PWM=n, the compilation
can't be performed. Hence, add a necessary stub.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 70f360dd7042cb843635ece9d28335a4addff9eb ]
This field can be read locklessly.
Fixes: 1536e2857bd3 ("tcp: Add a TCP_FASTOPEN socket option to get a max backlog on its listner")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230719212857.3943972-12-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d466effe282ddbab6acb6c3120c1de0ee1b86d57 ]
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
There are roughly 40 places where netdev->dev_addr is passed
as the destination to a of_get_mac_address() call. Add a helper
which takes a dev pointer instead, so it can call an appropriate
helper.
Note that of_get_mac_address() already assumes the address is
6 bytes long (ETH_ALEN) so use eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 1d6d537dc55d ("net: ethernet: mtk_eth_soc: handle probe deferral")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f3956ebb3bf06ab2266ad5ee2214aed46405810c ]
Convert Ethernet from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 1d6d537dc55d ("net: ethernet: mtk_eth_soc: handle probe deferral")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a82d62f708545d22859584e0e0620da8e3759bbc upstream.
This reverts commit eb26dfe8aa7eeb5a5aa0b7574550125f8aa4c3b3.
Commit eb26dfe8aa7e ("8250: add support for ASIX devices with a FIFO
bug") merged on Jul 13, 2012 adds a quirk for PCI_VENDOR_ID_ASIX
(0x9710). But that ID is the same as PCI_VENDOR_ID_NETMOS defined in
1f8b061050c7 ("[PATCH] Netmos parallel/serial/combo support") merged
on Mar 28, 2005. In pci_serial_quirks array, the NetMos entry always
takes precedence over the ASIX entry even since it was initially
merged, code in that commit is always unreachable.
In my tests, adding the FIFO workaround to pci_netmos_init() makes no
difference, and the vendor driver also does not have such workaround.
Given that the code was never used for over a decade, it's safe to
revert it.
Also, the real PCI_VENDOR_ID_ASIX should be 0x125b, which is used on
their newer AX99100 PCIe serial controllers released on 2016. The FIFO
workaround should not be intended for these newer controllers, and it
was never implemented in vendor driver.
Fixes: eb26dfe8aa7e ("8250: add support for ASIX devices with a FIFO bug")
Cc: stable <stable@kernel.org>
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230619155743.827859-1-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit afa4bb778e48d79e4a642ed41e3b4e0de7489a6c upstream.
Dave Airlie reports that gcc-13.1.1 has started complaining about some
of the workqueue code in 32-bit arm builds:
kernel/workqueue.c: In function ‘get_work_pwq’:
kernel/workqueue.c:713:24: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
713 | return (void *)(data & WORK_STRUCT_WQ_DATA_MASK);
| ^
[ ... a couple of other cases ... ]
and while it's not immediately clear exactly why gcc started complaining
about it now, I suspect it's some C23-induced enum type handlign fixup in
gcc-13 is the cause.
Whatever the reason for starting to complain, the code and data types
are indeed disgusting enough that the complaint is warranted.
The wq code ends up creating various "helper constants" (like that
WORK_STRUCT_WQ_DATA_MASK) using an enum type, which is all kinds of
confused. The mask needs to be 'unsigned long', not some unspecified
enum type.
To make matters worse, the actual "mask and cast to a pointer" is
repeated a couple of times, and the cast isn't even always done to the
right pointer, but - as the error case above - to a 'void *' with then
the compiler finishing the job.
That's now how we roll in the kernel.
So create the masks using the proper types rather than some ambiguous
enumeration, and use a nice helper that actually does the type
conversion in one well-defined place.
Incidentally, this magically makes clang generate better code. That,
admittedly, is really just a sign of clang having been seriously
confused before, and cleaning up the typing unconfuses the compiler too.
Reported-by: Dave Airlie <airlied@gmail.com>
Link: https://lore.kernel.org/lkml/CAPM=9twNnV4zMCvrPkw3H-ajZOH-01JVh_kDrxdPYQErz8ZTdA@mail.gmail.com/
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 36ce9d76b0a93bae799e27e4f5ac35478c676592 upstream.
As the ramfs-based tmpfs uses ramfs_init_fs_context() for the
init_fs_context method, which allocates fc->s_fs_info, use ramfs_kill_sb()
to free it and avoid a memory leak.
Link: https://lkml.kernel.org/r/20230607161523.2876433-1-roberto.sassu@huaweicloud.com
Fixes: c3b1b1cbf002 ("ramfs: add support for "mode=" mount option")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
detection"
[ Upstream commit df49f2a0ac4a34c0cb4b5c233fcfa0add644c43c ]
This reverts commit edd60d24bd858cef165274e4cd6cab43bdc58d15.
Heikki reports that this should not be a global flag just to work around
one broken driver and should be fixed differently, so revert it.
Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Fixes: edd60d24bd85 ("usb: common: usb-conn-gpio: Set last role to unknown before initial detection")
Link: https://lore.kernel.org/r/ZImE4L3YgABnCIsP@kuha.fi.intel.com
Cc: Prashanth K <quic_prashk@quicinc.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit edd60d24bd858cef165274e4cd6cab43bdc58d15 ]
Currently if we bootup a device without cable connected, then
usb-conn-gpio won't call set_role() since last_role is same as
current role. This happens because during probe last_role gets
initialised to zero.
To avoid this, added a new constant in enum usb_role, last_role
is set to USB_ROLE_UNKNOWN before performing initial detection.
While at it, also handle default case for the usb_role switch
in cdns3, intel-xhci-usb-role-switch & musb/jz4740 to avoid
build warnings.
Fixes: 4602f3bff266 ("usb: common: add USB GPIO based connection detection driver")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <1685544074-17337-1-git-send-email-quic_prashk@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 028725e73375a1ff080bbdf9fb503306d0116f28 upstream.
commit dd0ff4d12dd2 ("bootmem: remove the vmemmap pages from kmemleak in
put_page_bootmem") fix an overlaps existing problem of kmemleak. But the
problem still existed when HAVE_BOOTMEM_INFO_NODE is disabled, because in
this case, free_bootmem_page() will call free_reserved_page() directly.
Fix the problem by adding kmemleak_free_part() in free_bootmem_page() when
HAVE_BOOTMEM_INFO_NODE is disabled.
Link: https://lkml.kernel.org/r/20230704101942.2819426-1-liushixin2@huawei.com
Fixes: f41f2ed43ca5 ("mm: hugetlb: free the vmemmap pages associated with each HugeTLB page")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Acked-by: Muchun Song <songmuchun@bytedance.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2aa5ac633259843f656eb6ecff4cf01e8e810c5e ]
Add a pci_clear_master() stub when CONFIG_PCI is not set so drivers that
support both PCI and platform devices don't need #ifdefs or extra Kconfig
symbols for the PCI parts.
[bhelgaas: commit log]
Fixes: 6a479079c072 ("PCI: Add pci_clear_master() as opposite of pci_set_master()")
Link: https://lore.kernel.org/r/20230531102744.2354313-1-suijingfeng@loongson.cn
Signed-off-by: Sui Jingfeng <suijingfeng@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9fde4c557f78ee2f3626e92b4089ce9d54a2573a ]
The Stuff Bit Count is always coded on 4 bits [1]. Update the Stuff
Bit Count size accordingly.
In addition, the CRC fields of CAN FD Frames contain stuff bits at
fixed positions called fixed stuff bits [2]. The CRC field starts with
a fixed stuff bit and then has another fixed stuff bit after each
fourth bit [2], which allows us to derive this formula:
FSB count = 1 + round_down(len(CRC field)/4)
The length of the CRC field is [1]:
len(CRC field) = len(Stuff Bit Count) + len(CRC)
= 4 + len(CRC)
with len(CRC) either 17 or 21 bits depending of the payload length.
In conclusion, for CRC17:
FSB count = 1 + round_down((4 + 17)/4)
= 6
and for CRC 21:
FSB count = 1 + round_down((4 + 21)/4)
= 7
Add a Fixed Stuff bits (FSB) field with above values and update
CANFD_FRAME_OVERHEAD_SFF and CANFD_FRAME_OVERHEAD_EFF accordingly.
[1] ISO 11898-1:2015 section 10.4.2.6 "CRC field":
The CRC field shall contain the CRC sequence followed by a recessive
CRC delimiter. For FD Frames, the CRC field shall also contain the
stuff count.
Stuff count
If FD Frames, the stuff count shall be at the beginning of the CRC
field. It shall consist of the stuff bit count modulo 8 in a 3-bit
gray code followed by a parity bit [...]
[2] ISO 11898-1:2015 paragraph 10.5 "Frame coding":
In the CRC field of FD Frames, the stuff bits shall be inserted at
fixed positions; they are called fixed stuff bits. There shall be a
fixed stuff bit before the first bit of the stuff count, even if the
last bits of the preceding field are a sequence of five consecutive
bits of identical value, there shall be only the fixed stuff bit,
there shall not be two consecutive stuff bits. A further fixed stuff
bit shall be inserted after each fourth bit of the CRC field [...]
Fixes: 85d99c3e2a13 ("can: length: can_skb_get_frame_len(): introduce function to get data length of frame in data link layer")
Suggested-by: Thomas Kopp <Thomas.Kopp@microchip.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Thomas Kopp <Thomas.Kopp@microchip.com>
Link: https://lore.kernel.org/all/20230611025728.450837-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9a5cb79762e0eda17ca15c2a6eaca4622383c21c ]
When calling bpf_sk_lookup_tcp(), bpf_sk_lookup_udp() or
bpf_skc_lookup_tcp() from tc/xdp ingress, VRF socket bindings aren't
respoected, i.e. unbound sockets are returned, and bound sockets aren't
found.
VRF binding is determined by the sdif argument to sk_lookup(), however
when called from tc the IP SKB control block isn't initialized and thus
inet{,6}_sdif() always returns 0.
Fix by calculating sdif for the tc/xdp flows by observing the device's
l3 enslaved state.
The cg/sk_skb hooking points which are expected to support
inet{,6}_sdif() pass sdif=-1 which makes __bpf_skc_lookup() use the
existing logic.
Fixes: 6acc9b432e67 ("bpf: Add helper to retrieve socket in BPF")
Signed-off-by: Gilad Sever <gilad9366@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Cc: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/bpf/20230621104211.301902-4-gilad9366@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
config
[ Upstream commit 5e008df11c55228a86a1bae692cc2002503572c9 ]
Patch series "watchdog/hardlockup: Add the buddy hardlockup detector", v5.
This patch series adds the "buddy" hardlockup detector. In brief, the
buddy hardlockup detector can detect hardlockups without arch-level
support by having CPUs checkup on a "buddy" CPU periodically.
Given the new design of this patch series, testing all combinations is
fairly difficult. I've attempted to make sure that all combinations of
CONFIG_ options are good, but it wouldn't surprise me if I missed
something. I apologize in advance and I'll do my best to fix any
problems that are found.
This patch (of 18):
The real watchdog_update_hrtimer_threshold() is defined in
kernel/watchdog_hld.c. That file is included if
CONFIG_HARDLOCKUP_DETECTOR_PERF and the function is defined in that file
if CONFIG_HARDLOCKUP_CHECK_TIMESTAMP.
The dummy version of the function in "nmi.h" didn't get that quite right.
While this doesn't appear to be a huge deal, it's nice to make it
consistent.
It doesn't break builds because CHECK_TIMESTAMP is only defined by x86 so
others don't get a double definition, and x86 uses perf lockup detector,
so it gets the out of line version.
Link: https://lkml.kernel.org/r/20230519101840.v5.18.Ia44852044cdcb074f387e80df6b45e892965d4a1@changeid
Link: https://lkml.kernel.org/r/20230519101840.v5.1.I8cbb2f4fa740528fcfade4f5439b6cdcdd059251@changeid
Fixes: 7edaeb6841df ("kernel/watchdog: Prevent false positives with turbo modes")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Ian Rogers <irogers@google.com>
Cc: Lecopzer Chen <lecopzer.chen@mediatek.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masayoshi Mizuma <msys.mizuma@gmail.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Pingfan Liu <kernelfans@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com>
Cc: Ricardo Neri <ricardo.neri@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Sumit Garg <sumit.garg@linaro.org>
Cc: Tzung-Bi Shih <tzungbi@chromium.org>
Cc: Will Deacon <will@kernel.org>
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 247c8d2f9837a3e29e3b6b7a4aa9c36c37659dd4 ]
A couple of functions from fs/pipe.c are used both internally
and for the watch queue code, but the declaration is only
visible when the latter is enabled:
fs/pipe.c:1254:5: error: no previous prototype for 'pipe_resize_ring'
fs/pipe.c:758:15: error: no previous prototype for 'account_pipe_buffers'
fs/pipe.c:764:6: error: no previous prototype for 'too_many_pipe_buffers_soft'
fs/pipe.c:771:6: error: no previous prototype for 'too_many_pipe_buffers_hard'
fs/pipe.c:777:6: error: no previous prototype for 'pipe_is_unprivileged_user'
Make the visible unconditionally to avoid these warnings.
Fixes: c73be61cede5 ("pipe: Add general notification queue support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Message-Id: <20230516195629.551602-1-arnd@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
From: Tony Luck <tony.luck@intel.com>
commit d302c2398ba269e788a4f37ae57c07a7fcabaa42 upstream.
Cannot call memory_failure() directly from the fault handler because
mmap_lock (and others) are held.
It is important, but not urgent, to mark the source page as h/w poisoned
and unmap it from other tasks.
Use memory_failure_queue() to request a call to memory_failure() for the
page with the error.
Also provide a stub version for CONFIG_MEMORY_FAILURE=n
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20221021200120.175753-3-tony.luck@intel.com
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Shuai Xue <xueshuai@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Due to missing commits
e591ef7d96d6e ("mm,hwpoison,hugetlb,memory_hotplug: hotremove memory section with hwpoisoned hugepage")
5033091de814a ("mm/hwpoison: introduce per-memory_block hwpoison counter")
The impact of e591ef7d96d6e is its introduction of an additional flag in
__get_huge_page_for_hwpoison() that serves as an indication a hwpoisoned
hugetlb page should have its migratable bit cleared.
The impact of 5033091de814a is contexual.
Resolve by ignoring both missing commits. - jane]
Signed-off-by: Jane Chu <jane.chu@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a873dfe1032a132bf89f9e19a6ac44f5a0b78754 upstream.
Patch series "Copy-on-write poison recovery", v3.
Part 1 deals with the process that triggered the copy on write fault with
a store to a shared read-only page. That process is send a SIGBUS with
the usual machine check decoration to specify the virtual address of the
lost page, together with the scope.
Part 2 sets up to asynchronously take the page with the uncorrected error
offline to prevent additional machine check faults. H/t to Miaohe Lin
<linmiaohe@huawei.com> and Shuai Xue <xueshuai@linux.alibaba.com> for
pointing me to the existing function to queue a call to memory_failure().
On x86 there is some duplicate reporting (because the error is also
signalled by the memory controller as well as by the core that triggered
the machine check). Console logs look like this:
This patch (of 2):
If the kernel is copying a page as the result of a copy-on-write
fault and runs into an uncorrectable error, Linux will crash because
it does not have recovery code for this case where poison is consumed
by the kernel.
It is easy to set up a test case. Just inject an error into a private
page, fork(2), and have the child process write to the page.
I wrapped that neatly into a test at:
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/ras-tools.git
just enable ACPI error injection and run:
# ./einj_mem-uc -f copy-on-write
Add a new copy_user_highpage_mc() function that uses copy_mc_to_kernel()
on architectures where that is available (currently x86 and powerpc).
When an error is detected during the page copy, return VM_FAULT_HWPOISON
to caller of wp_page_copy(). This propagates up the call stack. Both x86
and powerpc have code in their fault handler to deal with this code by
sending a SIGBUS to the application.
Note that this patch avoids a system crash and signals the process that
triggered the copy-on-write action. It does not take any action for the
memory error that is still in the shared page. To handle that a call to
memory_failure() is needed. But this cannot be done from wp_page_copy()
because it holds mmap_lock(). Perhaps the architecture fault handlers
can deal with this loose end in a subsequent patch?
On Intel/x86 this loose end will often be handled automatically because
the memory controller provides an additional notification of the h/w
poison in memory, the handler for this will call memory_failure(). This
isn't a 100% solution. If there are multiple errors, not all may be
logged in this way.
Cc: <stable@vger.kernel.org>
[tony.luck@intel.com: add call to kmsan_unpoison_memory(), per Miaohe Lin]
Link: https://lkml.kernel.org/r/20221031201029.102123-2-tony.luck@intel.com
Link: https://lkml.kernel.org/r/20221021200120.175753-1-tony.luck@intel.com
Link: https://lkml.kernel.org/r/20221021200120.175753-2-tony.luck@intel.com
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Tested-by: Shuai Xue <xueshuai@linux.alibaba.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Due to missing commits
c89357e27f20d ("mm: support GUP-triggered unsharing of anonymous pages")
662ce1dc9caf4 ("delayacct: track delays from write-protect copy")
b073d7f8aee4e ("mm: kmsan: maintain KMSAN metadata for page operations")
The impact of c89357e27f20d is a name change from cow_user_page() to
__wp_page_copy_user().
The impact of 662ce1dc9caf4 is the introduction of a new feature of
tracking write-protect copy in delayacct.
The impact of b073d7f8aee4e is an introduction of KASAN feature.
None of these commits establishes meaningful dependency, hence resolve by
ignoring them. - jane]
Signed-off-by: Jane Chu <jane.chu@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cfe6807d82e97e81c3209dca9448f091e1448a57 ]
The core gpiolib code is able to deal with multiple interrupt parents
for a single gpio irqchip. It however only allows a single piece
of data to be conveyed to all flow handlers (either the gpio_chip
or some other, driver-specific data).
This means that drivers have to go through some interesting dance
to find the correct context, something that isn't great in interrupt
context (see aebdc8abc9db86e2bd33070fc2f961012fff74b4 for a prime
example).
Instead, offer an optional way for a pinctrl/gpio driver to provide
an array of pointers which gets used to provide the correct context
to the flow handler.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211026175815.52703-2-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Stable-dep-of: 8c00914e5438 ("gpiolib: Fix GPIO chip IRQ initialization restriction")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7257d930aadcd62d1c7971ab14f3b1126356abdc ]
L3_OUT and L4_OUT Bit fields range from Bit 0:4 and thus the
mask should be 0x1F instead of 0x0F.
Fixes: 0935ff5f1f0a ("regulator: pca9450: add pca9450 pmic driver")
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20230614125240.3946519-1-t.remmet@phytec.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1ac17586c950a2c129393f8a92901a2b357acf24 upstream.
The values of enum of_overlay_notify_action are used to index into
array of_overlay_action_name. Add an entry to of_overlay_action_name
for the value recently added to of_overlay_notify_action.
Array of_overlay_action_name[] is moved into include/linux/of.h
adjacent to enum of_overlay_notify_action to make the connection
between the two more obvious if either is modified in the future.
The only use of of_overlay_action_name is for error reporting in
overlay_notify(). All callers of overlay_notify() report the same
error, but with fewer details. Remove the redundant error reports
in the callers.
Fixes: 067c098766c6 ("of: overlay: rework overlay apply and remove kfree()s")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220502181742.1402826-2-frowand.list@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1202cdd665315c525b5237e96e0bedc76d7e754f upstream.
DECnet is an obsolete network protocol that receives more attention
from kernel janitors than users. It belongs in computer protocol
history museum not in Linux kernel.
It has been "Orphaned" in kernel since 2010. The iproute2 support
for DECnet was dropped in 5.0 release. The documentation link on
Sourceforge says it is abandoned there as well.
Leave the UAPI alone to keep userspace programs compiling.
This means that there is still an empty neighbour table
for AF_DECNET.
The table of /proc/sys/net entries was updated to match
current directories and reformatted to be alphabetical.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: David Ahern <dsahern@kernel.org>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 067c098766c6af667a9002d4e33cf1f3c998abbe ]
Fix various kfree() issues related to of_overlay_apply().
- Double kfree() of fdt and tree when init_overlay_changeset()
returns an error.
- free_overlay_changeset() free the root of the unflattened
overlay (variable tree) instead of the memory that contains
the unflattened overlay.
- For the case of a failure during applying an overlay, move kfree()
of new_fdt and overlay_mem into free_overlay_changeset(), which
is called by the function that allocated them.
- For the case of removing an overlay, the kfree() of new_fdt and
overlay_mem remains in free_overlay_changeset().
- Check return value of of_fdt_unflatten_tree() for error instead
of checking the returned value of overlay_root.
- When storing pointers to allocated objects in ovcs, do so as
near to the allocation as possible instead of in deeply layered
function.
More clearly document policy related to lifetime of pointers into
overlay memory.
Double kfree()
Reported-by: Slawomir Stepien <slawomir.stepien@nokia.com>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220420222505.928492-3-frowand.list@gmail.com
Stable-dep-of: 39affd1fdf65 ("of: overlay: Fix missing of_node_put() in error case of init_overlay_changeset()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0143d148d1e882fb1538dc9974c94d63961719b9 upstream.
The current implementation of usbdev_mmap uses usb_alloc_coherent to
allocate memory pages that will later be mapped into the user space.
Meanwhile, usb_alloc_coherent employs three different methods to
allocate memory, as outlined below:
* If hcd->localmem_pool is non-null, it uses gen_pool_dma_alloc to
allocate memory;
* If DMA is not available, it uses kmalloc to allocate memory;
* Otherwise, it uses dma_alloc_coherent.
However, it should be noted that gen_pool_dma_alloc does not guarantee
that the resulting memory will be page-aligned. Furthermore, trying to
map slab pages (i.e., memory allocated by kmalloc) into the user space
is not resonable and can lead to problems, such as a type confusion bug
when PAGE_TABLE_CHECK=y [1].
To address these issues, this patch introduces hcd_alloc_coherent_pages,
which addresses the above two problems. Specifically,
hcd_alloc_coherent_pages uses gen_pool_dma_alloc_align instead of
gen_pool_dma_alloc to ensure that the memory is page-aligned. To replace
kmalloc, hcd_alloc_coherent_pages directly allocates pages by calling
__get_free_pages.
Reported-by: syzbot+fcf1a817ceb50935ce99@syzkaller.appspotmail.comm
Closes: https://lore.kernel.org/lkml/000000000000258e5e05fae79fc1@google.com/ [1]
Fixes: f7d34b445abc ("USB: Add support for usbfs zerocopy.")
Fixes: ff2437befd8f ("usb: host: Fix excessive alignment restriction for local memory allocations")
Cc: stable@vger.kernel.org
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230515130958.32471-2-lrh2000@pku.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5c3b74a92aa285a3df722bf6329ba7ccf70346d6 ]
Add READ_ONCE()/WRITE_ONCE() on accesses to the sock flow table.
This also prevents a (smart ?) compiler to remove the condition in:
if (table->ents[index] != newval)
table->ents[index] = newval;
We need the condition to avoid dirtying a shared cache line.
Fixes: fec5e652e58f ("rfs: Receive Flow Steering")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
power_supply_set_input_current_limit_from_supplier()
[ Upstream commit 2220af8ca61ae67de4ec3deec1c6395a2f65b9fd ]
Some (USB) charger ICs have variants with USB D+ and D- pins to do their
own builtin charger-type detection, like e.g. the bq24190 and bq25890 and
also variants which lack this functionality, e.g. the bq24192 and bq25892.
In case the charger-type; and thus the input-current-limit detection is
done outside the charger IC then we need some way to communicate this to
the charger IC. In the past extcon was used for this, but if the external
detection does e.g. full USB PD negotiation then the extcon cable-types do
not convey enough information.
For these setups it was decided to model the external charging "brick"
and the parameters negotiated with it as a power_supply class-device
itself; and power_supply_set_input_current_limit_from_supplier() was
introduced to allow drivers to get the input-current-limit this way.
But in some cases psy drivers may want to know other properties, e.g. the
bq25892 can do "quick-charge" negotiation by pulsing its current draw,
but this should only be done if the usb_type psy-property of its supplier
is set to DCP (and device-properties indicate the board allows higher
voltages).
Instead of adding extra helper functions for each property which
a psy-driver wants to query from its supplier, refactor
power_supply_set_input_current_limit_from_supplier() into a
more generic power_supply_get_property_from_supplier() function.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Stable-dep-of: 77c2a3097d70 ("power: supply: bq24190: Call power_supply_changed() after updating input current")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
sign changes
[ Upstream commit 939a116142012926e25de0ea6b7e2f8d86a5f1b6 ]
On gauges where the current register is signed, there is no charging
flag in the flags register. So only checking flags will not result
in power_supply_changed() getting called when e.g. a charger is plugged
in and the current sign changes from negative (discharging) to
positive (charging).
This causes userspace's notion of the status to lag until userspace
does a poll.
And when a power_supply_leds.c LED trigger is used to indicate charging
status with a LED, this LED will lag until the capacity percentage
changes, which may take many minutes (because the LED trigger only is
updated on power_supply_changed() calls).
Fix this by calling bq27xxx_battery_current_and_status() on gauges with
a signed current register and checking if the status has changed.
Fixes: 297a533b3e62 ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c7dd225bc224726c22db08e680bf787f60ebdee3 upstream.
SW Steering uses RC QP for writing STEs to ICM. This writingis done in LB
(loopback), and FL (force-loopback) QP is preferred for performance. FL is
available when RoCE is enabled or disabled based on RoCE caps.
This patch adds reading of FL capability from HCA caps in addition to the
existing reading from RoCE caps, thus fixing the case where we didn't
have loopback enabled when RoCE was disabled.
Fixes: 7304d603a57a ("net/mlx5: DR, Add support for force-loopback QP")
Signed-off-by: Itamar Gozlan <igozlan@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f15afbd34d8fadbd375f1212e97837e32bc170cc upstream.
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. It was spotted by UBSAN.
So let's just fix this by using the BIT() helper for all SB_* flags.
Fixes: e462ec50cb5f ("VFS: Differentiate mount flags (MS_*) from internal superblock flags")
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Message-Id: <20230424051835.374204-1-gehao@kylinos.cn>
[brauner@kernel.org: use BIT() for all SB_* flags]
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 19b8766459c41c6f318f8a548cc1c66dffd18363 upstream.
Each physical partition can provide multiple services each with UUID.
Each such service can be presented as logical partition with a unique
combination of VM ID and UUID. The number of distinct UUID in a system
will be less than or equal to the number of logical partitions.
However, currently it fails to register more than one logical partition
or service within a physical partition as the device name contains only
VM ID while both VM ID and UUID are maintained in the partition information.
The kernel complains with the below message:
| sysfs: cannot create duplicate filename '/devices/arm-ffa-8001'
| CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.3.0-rc7 #8
| Hardware name: FVP Base RevC (DT)
| Call trace:
| dump_backtrace+0xf8/0x118
| show_stack+0x18/0x24
| dump_stack_lvl+0x50/0x68
| dump_stack+0x18/0x24
| sysfs_create_dir_ns+0xe0/0x13c
| kobject_add_internal+0x220/0x3d4
| kobject_add+0x94/0x100
| device_add+0x144/0x5d8
| device_register+0x20/0x30
| ffa_device_register+0x88/0xd8
| ffa_setup_partitions+0x108/0x1b8
| ffa_init+0x2ec/0x3a4
| do_one_initcall+0xcc/0x240
| do_initcall_level+0x8c/0xac
| do_initcalls+0x54/0x94
| do_basic_setup+0x1c/0x28
| kernel_init_freeable+0x100/0x16c
| kernel_init+0x20/0x1a0
| ret_from_fork+0x10/0x20
| kobject_add_internal failed for arm-ffa-8001 with -EEXIST, don't try to
| register things with the same name in the same directory.
| arm_ffa arm-ffa: unable to register device arm-ffa-8001 err=-17
| ARM FF-A: ffa_setup_partitions: failed to register partition ID 0x8001
By virtue of being random enough to avoid collisions when generated in a
distributed system, there is no way to compress UUID keys to the number
of bits required to identify each. We can eliminate '-' in the name but
it is not worth eliminating 4 bytes and add unnecessary logic for doing
that. Also v1.0 doesn't provide the UUID of the partitions which makes
it hard to use the same for the device name.
So to keep it simple, let us alloc an ID using ida_alloc() and append the
same to "arm-ffa" to make up a unique device name. Also stash the id value
in ffa_dev to help freeing the ID later when the device is destroyed.
Fixes: e781858488b9 ("firmware: arm_ffa: Add initial FFA bus support for device enumeration")
Reported-by: Lucian Paul-Trifu <lucian.paul-trifu@arm.com>
Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-3-d9108e43a176@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c00bc80462afc7963f449d7f21d896d2f629cacc upstream.
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 8cfaaa811894 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 13890626501ffda22b18213ddaf7930473da5792 upstream.
Many of the older USB drivers in the Linux USB stack were written
based simply on a vendor's device specification. They use the
endpoint information in the spec and assume these endpoints will
always be present, with the properties listed, in any device matching
the given vendor and product IDs.
While that may have been true back then, with spoofing and fuzzing it
is not true any more. More and more we are finding that those old
drivers need to perform at least a minimum of checking before they try
to use any endpoint other than ep0.
To make this checking as simple as possible, we now add a couple of
utility routines to the USB core. usb_check_bulk_endpoints() and
usb_check_int_endpoints() take an interface pointer together with a
list of endpoint addresses (numbers and directions). They check that
the interface's current alternate setting includes endpoints with
those addresses and that each of these endpoints has the right type:
bulk or interrupt, respectively.
Although we already have usb_find_common_endpoints() and related
routines meant for a similar purpose, they are not well suited for
this kind of checking. Those routines find endpoints of various
kinds, but only one (either the first or the last) of each kind, and
they don't verify that the endpoints' addresses agree with what the
caller expects.
In theory the new routines could be more general: They could take a
particular altsetting as their argument instead of always using the
interface's current altsetting. In practice I think this won't matter
too much; multiple altsettings tend to be used for transferring media
(audio or visual) over isochronous endpoints, not bulk or interrupt.
Drivers for such devices will generally require more sophisticated
checking than these simplistic routines provide.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/dd2c8e8c-2c87-44ea-ba17-c64b97e201c9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ae9b15fbe63447bc1d3bba3769f409d17ca6fdf6 upstream.
When the virtual interface's feature is updated, it synchronizes the
updated feature for its own lower interface.
This propagation logic should be worked as the iteration, not recursively.
But it works recursively due to the netdev notification unexpectedly.
This problem occurs when it disables LRO only for the team and bonding
interface type.
team0
|
+------+------+-----+-----+
| | | | |
team1 team2 team3 ... team200
If team0's LRO feature is updated, it generates the NETDEV_FEAT_CHANGE
event to its own lower interfaces(team1 ~ team200).
It is worked by netdev_sync_lower_features().
So, the NETDEV_FEAT_CHANGE notification logic of each lower interface
work iteratively.
But generated NETDEV_FEAT_CHANGE event is also sent to the upper
interface too.
upper interface(team0) generates the NETDEV_FEAT_CHANGE event for its own
lower interfaces again.
lower and upper interfaces receive this event and generate this
event again and again.
So, the stack overflow occurs.
But it is not the infinite loop issue.
Because the netdev_sync_lower_features() updates features before
generating the NETDEV_FEAT_CHANGE event.
Already synchronized lower interfaces skip notification logic.
So, it is just the problem that iteration logic is changed to the
recursive unexpectedly due to the notification mechanism.
Reproducer:
ip link add team0 type team
ethtool -K team0 lro on
for i in {1..200}
do
ip link add team$i master team0 type team
ethtool -K team$i lro on
done
ethtool -K team0 lro off
In order to fix it, the notifier_ctx member of bonding/team is introduced.
Reported-by: syzbot+60748c96cf5c6df8e581@syzkaller.appspotmail.com
Fixes: fd867d51f889 ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230517143010.3596250-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b93c2a68f3d9dc98ec30dcb342ae47c1c8d09d18 ]
The wakeup bit in the bmAttributes field indicates whether the device
is configured for remote wakeup. But this field should be allowed to
set only if the UDC supports such wakeup mechanism. So configure this
field based on UDC capability. Also inform the UDC whether the device
is configured for remote wakeup by implementing a gadget op.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Link: https://lore.kernel.org/r/1679694482-16430-2-git-send-email-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 4e8ef34e36f2 ("usb: dwc3: fix gadget mode suspend interrupt handler issue")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 948f072ada23e0a504c5e4d7d71d4c83bd0785ec ]
Since the ->xprt_ctxt pointer was added to svc_deferred_req, it has not
been sufficient to use kfree() to free a deferred request. We may need
to free the ctxt as well.
As freeing the ctxt is all that ->xpo_release_rqst() does, we repurpose
it to explicit do that even when the ctxt is not stored in an rqst.
So we now have ->xpo_release_ctxt() which is given an xprt and a ctxt,
which may have been taken either from an rqst or from a dreq. The
caller is now responsible for clearing that pointer after the call to
->xpo_release_ctxt.
We also clear dr->xprt_ctxt when the ctxt is moved into a new rqst when
revisiting a deferred request. This ensures there is only one pointer
to the ctxt, so the risk of double freeing in future is reduced. The
new code in svc_xprt_release which releases both the ctxt and any
rq_deferred depends on this.
Fixes: 773f91b2cf3f ("SUNRPC: Fix NFSD's request deferral on RDMA transports")
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 983084b2672c593959e3148d6a17c8b920797dde ]
Clean up: This field is now always set to zero.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Stable-dep-of: 948f072ada23 ("SUNRPC: always free ctxt when freeing deferred request")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e0b081d17a9f4e5c0cbb0e5fbeb1abe3de0f7e4e ]
With KCSAN enabled, end_of_stack() can get out-of-lined. Force it
inline.
Fixes the following warnings:
vmlinux.o: warning: objtool: check_stackleak_irqoff+0x2b: call to end_of_stack() leaves .noinstr.text section
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/cc1b4d73d3a428a00d206242a68fdf99a934ca7b.1681320026.git.jpoimboe@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d2c48b2387eb89e0bf2a2e06e30987cf410acad4 ]
Running a preempt-rt (v6.2-rc3-rt1) based kernel on an Ampere Altra
triggers:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:46
in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 24, name: cpuhp/0
preempt_count: 0, expected: 0
RCU nest depth: 0, expected: 0
3 locks held by cpuhp/0/24:
#0: ffffda30217c70d0 (cpu_hotplug_lock){++++}-{0:0}, at: cpuhp_thread_fun+0x5c/0x248
#1: ffffda30217c7120 (cpuhp_state-up){+.+.}-{0:0}, at: cpuhp_thread_fun+0x5c/0x248
#2: ffffda3021c711f0 (sdei_list_lock){....}-{3:3}, at: sdei_cpuhp_up+0x3c/0x130
irq event stamp: 36
hardirqs last enabled at (35): [<ffffda301e85b7bc>] finish_task_switch+0xb4/0x2b0
hardirqs last disabled at (36): [<ffffda301e812fec>] cpuhp_thread_fun+0x21c/0x248
softirqs last enabled at (0): [<ffffda301e80b184>] copy_process+0x63c/0x1ac0
softirqs last disabled at (0): [<0000000000000000>] 0x0
CPU: 0 PID: 24 Comm: cpuhp/0 Not tainted 5.19.0-rc3-rt5-[...]
Hardware name: WIWYNN Mt.Jade Server [...]
Call trace:
dump_backtrace+0x114/0x120
show_stack+0x20/0x70
dump_stack_lvl+0x9c/0xd8
dump_stack+0x18/0x34
__might_resched+0x188/0x228
rt_spin_lock+0x70/0x120
sdei_cpuhp_up+0x3c/0x130
cpuhp_invoke_callback+0x250/0xf08
cpuhp_thread_fun+0x120/0x248
smpboot_thread_fn+0x280/0x320
kthread+0x130/0x140
ret_from_fork+0x10/0x20
sdei_cpuhp_up() is called in the STARTING hotplug section,
which runs with interrupts disabled. Use a CPUHP_AP_ONLINE_DYN entry
instead to execute the cpuhp cb later, with preemption enabled.
SDEI originally got its own cpuhp slot to allow interacting
with perf. It got superseded by pNMI and this early slot is not
relevant anymore. [1]
Some SDEI calls (e.g. SDEI_1_0_FN_SDEI_PE_MASK) take actions on the
calling CPU. It is checked that preemption is disabled for them.
_ONLINE cpuhp cb are executed in the 'per CPU hotplug thread'.
Preemption is enabled in those threads, but their cpumask is limited
to 1 CPU.
Move 'WARN_ON_ONCE(preemptible())' statements so that SDEI cpuhp cb
don't trigger them.
Also add a check for the SDEI_1_0_FN_SDEI_PRIVATE_RESET SDEI call
which acts on the calling CPU.
[1]:
https://lore.kernel.org/all/5813b8c5-ae3e-87fd-fccc-94c9cd08816d@arm.com/
Suggested-by: James Morse <james.morse@arm.com>
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20230216084920.144064-1-pierre.gondois@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4063384ef762cc5946fc7a3f89879e76c6ec51e2 ]
Before blamed commit, pskb_may_pull() was used instead
of skb_header_pointer() in __vlan_get_protocol() and friends.
Few callers depended on skb->head being populated with MAC header,
syzbot caught one of them (skb_mac_gso_segment())
Add vlan_get_protocol_and_depth() to make the intent clearer
and use it where sensible.
This is a more generic fix than commit e9d3f80935b6
("net/af_packet: make sure to pull mac header") which was
dealing with a similar issue.
kernel BUG at include/linux/skbuff.h:2655 !
invalid opcode: 0000 [#1] SMP KASAN
CPU: 0 PID: 1441 Comm: syz-executor199 Not tainted 6.1.24-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
RIP: 0010:__skb_pull include/linux/skbuff.h:2655 [inline]
RIP: 0010:skb_mac_gso_segment+0x68f/0x6a0 net/core/gro.c:136
Code: fd 48 8b 5c 24 10 44 89 6b 70 48 c7 c7 c0 ae 0d 86 44 89 e6 e8 a1 91 d0 00 48 c7 c7 00 af 0d 86 48 89 de 31 d2 e8 d1 4a e9 ff <0f> 0b 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41
RSP: 0018:ffffc90001bd7520 EFLAGS: 00010286
RAX: ffffffff8469736a RBX: ffff88810f31dac0 RCX: ffff888115a18b00
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffffc90001bd75e8 R08: ffffffff84697183 R09: fffff5200037adf9
R10: 0000000000000000 R11: dffffc0000000001 R12: 0000000000000012
R13: 000000000000fee5 R14: 0000000000005865 R15: 000000000000fed7
FS: 000055555633f300(0000) GS:ffff8881f6a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000000 CR3: 0000000116fea000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
[<ffffffff847018dd>] __skb_gso_segment+0x32d/0x4c0 net/core/dev.c:3419
[<ffffffff8470398a>] skb_gso_segment include/linux/netdevice.h:4819 [inline]
[<ffffffff8470398a>] validate_xmit_skb+0x3aa/0xee0 net/core/dev.c:3725
[<ffffffff84707042>] __dev_queue_xmit+0x1332/0x3300 net/core/dev.c:4313
[<ffffffff851a9ec7>] dev_queue_xmit+0x17/0x20 include/linux/netdevice.h:3029
[<ffffffff851b4a82>] packet_snd net/packet/af_packet.c:3111 [inline]
[<ffffffff851b4a82>] packet_sendmsg+0x49d2/0x6470 net/packet/af_packet.c:3142
[<ffffffff84669a12>] sock_sendmsg_nosec net/socket.c:716 [inline]
[<ffffffff84669a12>] sock_sendmsg net/socket.c:736 [inline]
[<ffffffff84669a12>] __sys_sendto+0x472/0x5f0 net/socket.c:2139
[<ffffffff84669c75>] __do_sys_sendto net/socket.c:2151 [inline]
[<ffffffff84669c75>] __se_sys_sendto net/socket.c:2147 [inline]
[<ffffffff84669c75>] __x64_sys_sendto+0xe5/0x100 net/socket.c:2147
[<ffffffff8551d40f>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<ffffffff8551d40f>] do_syscall_64+0x2f/0x50 arch/x86/entry/common.c:80
[<ffffffff85600087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: 469aceddfa3e ("vlan: consolidate VLAN parsing code and limit max parsing depth")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 76c16d3e19446deea98b7883f261758b96b8781a ]
Using current implementation of polling mode, there is high chances we
will hit into timeout error when running phc2sys. Hence, update the
implementation of hardware crosstimestamping to use the MAC interrupt
service routine instead of polling for TSIS bit in the MAC Timestamp
Interrupt Status register to be set.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 8efbdbfa9938 ("net: stmmac: Initialize MAC_ONEUS_TIC_COUNTER register")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 162bd18eb55adf464a0fa2b4144b8d61c75ff7c2 ]
Add return value for dim_calc_stats. This is an indication for the
caller if curr_stats was assigned by the function. Avoid using
curr_stats uninitialized over {rdma/net}_dim, when no time delta between
samples. Coverity reported this potential use of an uninitialized
variable.
Fixes: 4c4dbb4a7363 ("net/mlx5e: Move dynamic interrupt coalescing code to include/linux")
Fixes: cb3c7fd4f839 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/r/20230507135743.138993-1-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c35e03eaece71101ff6cbf776b86403860ac8cc3 ]
The crypto completion function currently takes a pointer to a
struct crypto_async_request object. However, in reality the API
does not allow the use of any part of the object apart from the
data field. For example, ahash/shash will create a fake object
on the stack to pass along a different data field.
This leads to potential bugs where the user may try to dereference
or otherwise use the crypto_async_request object.
This patch adds some temporary scaffolding so that the completion
function can take a void * instead. Once affected users have been
converted this can be removed.
The helper crypto_request_complete will remain even after the
conversion is complete. It should be used instead of calling
the completion function directly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: 4140aafcff16 ("crypto: engine - fix crypto_queue backlog handling")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 79963fbfc233759bd8a43462f120d15a1bd4f4fa upstream.
Xilinx IPI message buffers allows 32-byte data transfer.
Fix documentation that says 12 bytes
Fixes: 4981b82ba2ff ("mailbox: ZynqMP IPI mailbox controller")
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230311012407.1292118-4-tanmay.shah@amd.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 691d0b782066a6eeeecbfceb7910a8f6184e6105 ]
Currently call_bind_status places a hard limit of 3 to the number of
retries on EACCES error. This limit was done to prevent NLM unlock
requests from being hang forever when the server keeps returning garbage.
However this change causes problem for cases when NLM service takes
longer than 9 seconds to register with the port mapper after a restart.
This patch removes this hard coded limit and let the RPC handles
the retry based on the standard hard/soft task semantics.
Fixes: 0b760113a3a1 ("NLM: Don't hang forever on NLM unlock requests")
Reported-by: Helen Chao <helen.chao@oracle.com>
Tested-by: Helen Chao <helen.chao@oracle.com>
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
