| Age | Commit message (Collapse) | Author |
|---|
|
commit d3f450533bbcb6dd4d7d59cadc9b61b7321e4ac1 upstream.
Nathan reports that recent kernels built with LTO will crash when doing
EFI boot using Fedora's GRUB and SHIM. The culprit turns out to be a
misaligned load from the TPM event log, which is annotated with
READ_ONCE(), and under LTO, this gets translated into a LDAR instruction
which does not tolerate misaligned accesses.
Interestingly, this does not happen when booting the same kernel
straight from the UEFI shell, and so the fact that the event log may
appear misaligned in memory may be caused by a bug in GRUB or SHIM.
However, using READ_ONCE() to access firmware tables is slightly unusual
in any case, and here, we only need to ensure that 'event' is not
dereferenced again after it gets unmapped, but this is already taken
care of by the implicit barrier() semantics of the early_memunmap()
call.
Cc: <stable@vger.kernel.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://github.com/ClangBuiltLinux/linux/issues/1782
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 196dff2712ca5a2e651977bb2fe6b05474111a83 upstream.
Instead of blindly creating the EFI random seed configuration table if
the RNG protocol is implemented and works, check whether such a EFI
configuration table was provided by an earlier boot stage and if so,
concatenate the existing and the new seeds, leaving it up to the core
code to mix it in and credit it the way it sees fit.
This can be used for, e.g., systemd-boot, to pass an additional seed to
Linux in a way that can be consumed by the kernel very early. In that
case, the following definitions should be used to pass the seed to the
EFI stub:
struct linux_efi_random_seed {
u32 size; // of the 'seed' array in bytes
u8 seed[];
};
The memory for the struct must be allocated as EFI_ACPI_RECLAIM_MEMORY
pool memory, and the address of the struct in memory should be installed
as a EFI configuration table using the following GUID:
LINUX_EFI_RANDOM_SEED_TABLE_GUID 1ce1e5bc-7ceb-42f2-81e5-8aadf180f57b
Note that doing so is safe even on kernels that were built without this
patch applied, but the seed will simply be overwritten with a seed
derived from the EFI RNG protocol, if available. The recommended seed
size is 32 bytes, and seeds larger than 512 bytes are considered
corrupted and ignored entirely.
In order to preserve forward secrecy, seeds from previous bootloaders
are memzero'd out, and in order to preserve memory, those older seeds
are also freed from memory. Freeing from memory without first memzeroing
is not safe to do, as it's possible that nothing else will ever
overwrite those pages used by EFI.
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
[ardb: incorporate Jason's followup changes to extend the maximum seed
size on the consumer end, memzero() it and drop a needless printk]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5e29dc36bd5e2166b834ceb19990d9e68a734d7d ]
When adding/deleting large number of elements in one step in ipset, it can
take a reasonable amount of time and can result in soft lockup errors. The
patch 5f7b51bf09ba ("netfilter: ipset: Limit the maximal range of
consecutive elements to add/delete") tried to fix it by limiting the max
elements to process at all. However it was not enough, it is still possible
that we get hung tasks. Lowering the limit is not reasonable, so the
approach in this patch is as follows: rely on the method used at resizing
sets and save the state when we reach a smaller internal batch limit,
unlock/lock and proceed from the saved state. Thus we can avoid long
continuous tasks and at the same time removed the limit to add/delete large
number of elements in one step.
The nfnl mutex is held during the whole operation which prevents one to
issue other ipset commands in parallel.
Fixes: 5f7b51bf09ba ("netfilter: ipset: Limit the maximal range of consecutive elements to add/delete")
Reported-by: syzbot+9204e7399656300bf271@syzkaller.appspotmail.com
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ab1ddef98a715eddb65309ffa83267e4e84a571e ]
Ceph has a need to know whether a particular inode has any locks set on
it. It's currently tracking that by a num_locks field in its
filp->private_data, but that's problematic as it tries to decrement this
field when releasing locks and that can race with the file being torn
down.
Add a new vfs_inode_has_locks helper that just returns whether any locks
are currently held on the inode.
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Stable-dep-of: 461ab10ef7e6 ("ceph: switch to vfs_inode_has_locks() to fix file lock bug")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1f0ae22ab470946143485a02cc1cd7e05c0f9120 ]
Fix SRIOV VST mode behavior to insert cvlan when a guest tag is already
present in the frame. Previous VST mode behavior was to drop packets or
override existing tag, depending on the device version.
In this patch we fix this behavior by correctly building the HW steering
rule with a push vlan action, or for older devices we ask the FW to stack
the vlan when a vlan is already present.
Fixes: 07bab9502641 ("net/mlx5: E-Switch, Refactor eswitch ingress acl codes")
Fixes: dfcb1ed3c331 ("net/mlx5: E-Switch, Vport ingress/egress ACLs rules for VST mode")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b18cba09e374637a0a3759d856a6bca94c133952 ]
Commit 9130b8dbc6ac ("SUNRPC: allow for upcalls for the same uid
but different gss service") introduced `auth` argument to
__gss_find_upcall(), but in gss_pipe_downcall() it was left as NULL
since it (and auth->service) was not (yet) determined.
When multiple upcalls with the same uid and different service are
ongoing, it could happen that __gss_find_upcall(), which returns the
first match found in the pipe->in_downcall list, could not find the
correct gss_msg corresponding to the downcall we are looking for.
Moreover, it might return a msg which is not sent to rpc.gssd yet.
We could see mount.nfs process hung in D state with multiple mount.nfs
are executed in parallel. The call trace below is of CentOS 7.9
kernel-3.10.0-1160.24.1.el7.x86_64 but we observed the same hang w/
elrepo kernel-ml-6.0.7-1.el7.
PID: 71258 TASK: ffff91ebd4be0000 CPU: 36 COMMAND: "mount.nfs"
#0 [ffff9203ca3234f8] __schedule at ffffffffa3b8899f
#1 [ffff9203ca323580] schedule at ffffffffa3b88eb9
#2 [ffff9203ca323590] gss_cred_init at ffffffffc0355818 [auth_rpcgss]
#3 [ffff9203ca323658] rpcauth_lookup_credcache at ffffffffc0421ebc
[sunrpc]
#4 [ffff9203ca3236d8] gss_lookup_cred at ffffffffc0353633 [auth_rpcgss]
#5 [ffff9203ca3236e8] rpcauth_lookupcred at ffffffffc0421581 [sunrpc]
#6 [ffff9203ca323740] rpcauth_refreshcred at ffffffffc04223d3 [sunrpc]
#7 [ffff9203ca3237a0] call_refresh at ffffffffc04103dc [sunrpc]
#8 [ffff9203ca3237b8] __rpc_execute at ffffffffc041e1c9 [sunrpc]
#9 [ffff9203ca323820] rpc_execute at ffffffffc0420a48 [sunrpc]
The scenario is like this. Let's say there are two upcalls for
services A and B, A -> B in pipe->in_downcall, B -> A in pipe->pipe.
When rpc.gssd reads pipe to get the upcall msg corresponding to
service B from pipe->pipe and then writes the response, in
gss_pipe_downcall the msg corresponding to service A will be picked
because only uid is used to find the msg and it is before the one for
B in pipe->in_downcall. And the process waiting for the msg
corresponding to service A will be woken up.
Actual scheduing of that process might be after rpc.gssd processes the
next msg. In rpc_pipe_generic_upcall it clears msg->errno (for A).
The process is scheduled to see gss_msg->ctx == NULL and
gss_msg->msg.errno == 0, therefore it cannot break the loop in
gss_create_upcall and is never woken up after that.
This patch adds a simple check to ensure that a msg which is not
sent to rpc.gssd yet is not chosen as the matching upcall upon
receiving a downcall.
Signed-off-by: minoura makoto <minoura@valinux.co.jp>
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@nec.com>
Tested-by: Hiroshi Shimamoto <h-shimamoto@nec.com>
Cc: Trond Myklebust <trondmy@hammerspace.com>
Fixes: 9130b8dbc6ac ("SUNRPC: allow for upcalls for same uid but different gss service")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a44e84a9b7764c72896f7241a0ec9ac7e7ef38dd ]
When manipulating xattr blocks, we can deadlock infinitely looping
inside ext4_xattr_block_set() where we constantly keep finding xattr
block for reuse in mbcache but we are unable to reuse it because its
reference count is too big. This happens because cache entry for the
xattr block is marked as reusable (e_reusable set) although its
reference count is too big. When this inconsistency happens, this
inconsistent state is kept indefinitely and so ext4_xattr_block_set()
keeps retrying indefinitely.
The inconsistent state is caused by non-atomic update of e_reusable bit.
e_reusable is part of a bitfield and e_reusable update can race with
update of e_referenced bit in the same bitfield resulting in loss of one
of the updates. Fix the problem by using atomic bitops instead.
This bug has been around for many years, but it became *much* easier
to hit after commit 65f8b80053a1 ("ext4: fix race when reusing xattr
blocks").
Cc: stable@vger.kernel.org
Fixes: 6048c64b2609 ("mbcache: add reusable flag to cache entries")
Fixes: 65f8b80053a1 ("ext4: fix race when reusing xattr blocks")
Reported-and-tested-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Reported-by: Thilo Fromm <t-lo@linux.microsoft.com>
Link: https://lore.kernel.org/r/c77bf00f-4618-7149-56f1-b8d1664b9d07@linux.microsoft.com/
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Link: https://lore.kernel.org/r/20221123193950.16758-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 307af6c879377c1c63e71cbdd978201f9c7ee8df ]
Use the fact that entries with elevated refcount are not removed from
the hash and just move removal of the entry from the hash to the entry
freeing time. When doing this we also change the generic code to hold
one reference to the cache entry, not two of them, which makes code
somewhat more obvious.
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20220712105436.32204-10-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: a44e84a9b776 ("ext4: fix deadlock due to mbcache entry corruption")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5fdded8448924e3631d466eea499b11606c43640 upstream.
The member void *data in the structure devfreq can be overwrite
by governor_userspace. For example:
1. The device driver assigned the devfreq governor to simple_ondemand
by the function devfreq_add_device() and init the devfreq member
void *data to a pointer of a static structure devfreq_simple_ondemand_data
by the function devfreq_add_device().
2. The user changed the devfreq governor to userspace by the command
"echo userspace > /sys/class/devfreq/.../governor".
3. The governor userspace alloced a dynamic memory for the struct
userspace_data and assigend the member void *data of devfreq to
this memory by the function userspace_init().
4. The user changed the devfreq governor back to simple_ondemand
by the command "echo simple_ondemand > /sys/class/devfreq/.../governor".
5. The governor userspace exited and assigned the member void *data
in the structure devfreq to NULL by the function userspace_exit().
6. The governor simple_ondemand fetched the static information of
devfreq_simple_ondemand_data in the function
devfreq_simple_ondemand_func() but the member void *data of devfreq was
assigned to NULL by the function userspace_exit().
7. The information of upthreshold and downdifferential is lost
and the governor simple_ondemand can't work correctly.
The member void *data in the structure devfreq is designed for
a static pointer used in a governor and inited by the function
devfreq_add_device(). This patch add an element named governor_data
in the devfreq structure which can be used by a governor(E.g userspace)
who want to assign a private data to do some private things.
Fixes: ce26c5bb9569 ("PM / devfreq: Add basic governors")
Cc: stable@vger.kernel.org # 5.10+
Reviewed-by: Chanwoo Choi <cwchoi00@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kant Fan <kant@allwinnertech.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 685e6311637e46f3212439ce2789f8a300e5050f ]
3 << 16 does not generate the correct mask for bits 16, 17 and 18.
Use the GENMASK macro to generate the correct mask instead.
Fixes: 84fef62d135b ("nvme: check admin passthru command effects")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6c1c5097781f563b70a81683ea6fdac21637573b ]
Long standing KCSAN issues are caused by data-race around
some dev->stats changes.
Most performance critical paths already use per-cpu
variables, or per-queue ones.
It is reasonable (and more correct) to use atomic operations
for the slow paths.
This patch adds an union for each field of net_device_stats,
so that we can convert paths that are not yet protected
by a spinlock or a mutex.
netdev_stats_to_stats64() no longer has an #if BITS_PER_LONG==64
Note that the memcpy() we were using on 64bit arches
had no provision to avoid load-tearing,
while atomic_long_read() is providing the needed protection
at no cost.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1d044ca035dc22df0d3b39e56f2881071d9118bd ]
The Hyper-V framebuffer code registers a panic notifier in order
to try updating its fbdev if the kernel crashed. The notifier
callback is straightforward, but it calls the vmbus_sendpacket()
routine eventually, and such function takes a spinlock for the
ring buffer operations.
Panic path runs in atomic context, with local interrupts and
preemption disabled, and all secondary CPUs shutdown. That said,
taking a spinlock might cause a lockup if a secondary CPU was
disabled with such lock taken. Fix it here by checking if the
ring buffer spinlock is busy on Hyper-V framebuffer panic notifier;
if so, bail-out avoiding the potential lockup scenario.
Cc: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Tianyu Lan <Tianyu.Lan@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Tested-by: Fabio A M Martins <fabiomirmar@gmail.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20220819221731.480795-10-gpiccoli@igalia.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e1be43d9b5d0d1310dbd90185a8e5c7145dde40f ]
In order to perform more open-coded replacements of common allocation
size arithmetic, the kernel needs saturating (SIZE_MAX) helpers for
multiplication, addition, and subtraction. For example, it is common in
allocators, especially on realloc, to add to an existing size:
p = krealloc(map->patch,
sizeof(struct reg_sequence) * (map->patch_regs + num_regs),
GFP_KERNEL);
There is no existing saturating replacement for this calculation, and
just leaving the addition open coded inside array_size() could
potentially overflow as well. For example, an overflow in an expression
for a size_t argument might wrap to zero:
array_size(anything, something_at_size_max + 1) == 0
Introduce size_mul(), size_add(), and size_sub() helpers that
implicitly promote arguments to size_t and saturated calculations for
use in allocations. With these helpers it is also possible to redefine
array_size(), array3_size(), flex_array_size(), and struct_size() in
terms of the new helpers.
As with the check_*_overflow() helpers, the new helpers use __must_check,
though what is really desired is a way to make sure that assignment is
only to a size_t lvalue. Without this, it's still possible to introduce
overflow/underflow via type conversion (i.e. from size_t to int).
Enforcing this will currently need to be left to static analysis or
future use of -Wconversion.
Additionally update the overflow unit tests to force runtime evaluation
for the pathological cases.
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Len Baker <len.baker@gmx.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Stable-dep-of: e001e6086939 ("fs/ntfs3: Harden against integer overflows")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4398693a9e24bcab0b99ea219073917991d0792b ]
We have several comments that start with '/**' but don't conform to the
kernel doc standard. Add proper detailed descriptions for the affected
definitions and move the docs from the forward declarations to the
struct definitions where applicable.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Stable-dep-of: bdbbae241a04 ("gpiolib: protect the GPIO device against being dropped while in use by user-space")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 99c05e4283a19a02a256f14100ca4ec3b2da3f62 ]
Add '__adis_enable_irq()' implementation which is the unlocked
version of 'adis_enable_irq()'.
Call '__adis_enable_irq()' instead of 'adis_enable_irq()' from
'__adis_intial_startup()' to keep the expected unlocked functionality.
This fix is needed to remove a deadlock for all devices which are
using 'adis_initial_startup()'. The deadlock occurs because the
same mutex is acquired twice, without releasing it.
The mutex is acquired once inside 'adis_initial_startup()', before
calling '__adis_initial_startup()', and once inside
'adis_enable_irq()', which is called by '__adis_initial_startup()'.
The deadlock is removed by calling '__adis_enable_irq()', instead of
'adis_enable_irq()' from within '__adis_initial_startup()'.
Fixes: b600bd7eb3335 ("iio: adis: do not disabe IRQs in 'adis_init()'")
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-2-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c39010ea6ba13bdf0003bd353e1d4c663aaac0a8 ]
Minor stylistic changes to address checkptach complains when called with
'--strict'.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220122130905.99-3-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 99c05e4283a1 ("iio: adis: add '__adis_enable_irq()' implementation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 31fa357ac809affd9f9a7d0b5d1991951e16beec ]
Some devices can't mask/unmask the data ready pin and in those cases
each driver was just calling '{dis}enable_irq()' to control the trigger
state. This change, moves that handling into the library by introducing
a new boolean in the data structure that tells the library that the
device cannot unmask the pin.
On top of controlling the trigger state, we can also use this flag to
automatically request the IRQ with 'IRQF_NO_AUTOEN' in case it is set.
So far, all users of the library want to start operation with IRQs/DRDY
pin disabled so it should be fairly safe to do this inside the library.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210903141423.517028-3-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 99c05e4283a1 ("iio: adis: add '__adis_enable_irq()' implementation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2e7dfb0e9cacad0f1adbc4b97f0b96ba35027f24 ]
Basic programmable non-PD Type-C port controllers do not need the full
TCPM library, but they share the same devicetree binding and the same
typec_capability structure. Factor out a helper for parsing those
properties which map to fields in struct typec_capability, so the code
can be shared between TCPM and basic non-TCPM drivers.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220214050118.61015-4-samuel@sholland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 581c848b610d ("extcon: usbc-tusb320: Update state on probe even if no IRQ pending")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a351d6087bf7d3d8440d58d3bf244ec64b89394a ]
When redirecting, we use sk_msg_to_ingress() to get the BPF_F_INGRESS
flag from the msg->flags. If apply_bytes is used and it is larger than
the current data being processed, sk_psock_msg_verdict() will not be
called when sendmsg() is called again. At this time, the msg->flags is 0,
and we lost the BPF_F_INGRESS flag.
So we need to save the BPF_F_INGRESS flag in sk_psock and use it when
redirection.
Fixes: 8934ce2fd081 ("bpf: sockmap redirect ingress support")
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/1669718441-2654-3-git-send-email-yangpc@wangsu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c3d96f690a790074b508fe183a41e36a00cd7ddd ]
Provide a CONFIG_PROC_FS=n fallback for proc_create_net_single_write().
Also provide a fallback for proc_create_net_data_write().
Fixes: 564def71765c ("proc: Add a way to make network proc files writable")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit efcef265fd83d9a68a68926abecb3e1dd3e260a8 ]
Add the explicit error and status register fields to 'struct ata_taskfile'
using the anonymous *union*s ('struct ide_taskfile' had that for ages!) and
update the libata taskfile code accordingly. There should be no object code
changes resulting from that...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Stable-dep-of: 7390896b3484 ("ata: libata: fix NCQ autosense logic")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 742bef476ca5352b16063161fb73a56629a6d995 ]
Use standard pr_{debug,info,notice,warn,err} macros instead of the
hand-crafted printk helpers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Stable-dep-of: 7390896b3484 ("ata: libata: fix NCQ autosense logic")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fd4e60bf0ef8eb9edcfa12dda39e8b6ee9060492 ]
Commit ee62c6b2dc93 ("eventfd: change int to __u64 in eventfd_signal()")
forgot to change int to __u64 in the CONFIG_EVENTFD=n stub function.
Link: https://lkml.kernel.org/r/20221124140154.104680-1-zhangqilong3@huawei.com
Fixes: ee62c6b2dc93 ("eventfd: change int to __u64 in eventfd_signal()")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Cc: Dylan Yudaken <dylany@fb.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Sha Zhengju <handai.szj@taobao.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d472cf797c4e268613dbce5ec9b95d0bcae19ecb ]
The simple attribute files do not accept a negative value since the commit
488dac0c9237 ("libfs: fix error cast of negative value in
simple_attr_write()"), so we have to use a 64-bit value to write a
negative value for a debugfs file created by debugfs_create_atomic_t().
This restores the previous behaviour by introducing
DEFINE_DEBUGFS_ATTRIBUTE_SIGNED for a signed value.
Link: https://lkml.kernel.org/r/20220919172418.45257-4-akinobu.mita@gmail.com
Fixes: 488dac0c9237 ("libfs: fix error cast of negative value in simple_attr_write()")
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reported-by: Zhao Gongyi <zhaogongyi@huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2e41f274f9aa71cdcc69dc1f26a3f9304a651804 ]
Patch series "fix error when writing negative value to simple attribute
files".
The simple attribute files do not accept a negative value since the commit
488dac0c9237 ("libfs: fix error cast of negative value in
simple_attr_write()"), but some attribute files want to accept a negative
value.
This patch (of 3):
The simple attribute files do not accept a negative value since the commit
488dac0c9237 ("libfs: fix error cast of negative value in
simple_attr_write()"), so we have to use a 64-bit value to write a
negative value.
This adds DEFINE_SIMPLE_ATTRIBUTE_SIGNED for a signed value.
Link: https://lkml.kernel.org/r/20220919172418.45257-1-akinobu.mita@gmail.com
Link: https://lkml.kernel.org/r/20220919172418.45257-2-akinobu.mita@gmail.com
Fixes: 488dac0c9237 ("libfs: fix error cast of negative value in simple_attr_write()")
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reported-by: Zhao Gongyi <zhaogongyi@huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2f117484329b233455ee278f2d9b0a4356835060 ]
When `timerqueue_getnext()` is called on an empty timer queue, it will
use `rb_entry()` on a NULL pointer, which is invalid. Fix that by using
`rb_entry_safe()` which handles NULL pointers.
This has not caused any issues so far because the offset of the `rb_node`
member in `timerqueue_node` is 0, so `rb_entry()` is essentially a no-op.
Fixes: 511885d7061e ("lib/timerqueue: Rely on rbtree semantics for next timer")
Signed-off-by: Barnabás Pőcze <pobrn@protonmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20221114195421.342929-1-pobrn@protonmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 99139b80c1b3d73026ed8be2de42c52e2976ab64 ]
APR and other packet routers like GPR are pretty much same and
interact with other drivers in similar way.
Ex: GPR ports can be considered as APR services, only difference
is they are allocated dynamically.
Other difference is packet layout, which should not matter
with the apis abstracted. Apart from this the rest of the
functionality is pretty much identical across APR and GPR.
Make the apr code more reusable by abstracting it service level,
rather than device level so that we do not need to write
new drivers for other new packet routers like GPR.
This patch is in preparation to add GPR support to this driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210927135559.738-4-srinivas.kandagatla@linaro.org
Stable-dep-of: 6d7860f5750d ("soc: qcom: apr: Add check for idr_alloc and of_property_read_string_index")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 26e8f6a75248247982458e8237b98c9fb2ffcf9d ]
bitfield mode in ocr register has only 2 bits not 3, so correct
the OCR_MODE_MASK define.
Signed-off-by: Heiko Schocher <hs@denx.de>
Link: https://lore.kernel.org/all/20221123071636.2407823-1-hs@denx.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 10bc8e4af65946b727728d7479c028742321b60a upstream.
Commit 868f9f2f8e00 ("vfs: fix copy_file_range() regression in cross-fs
copies") removed fallback to generic_copy_file_range() for cross-fs
cases inside vfs_copy_file_range().
To preserve behavior of nfsd and ksmbd server-side-copy, the fallback to
generic_copy_file_range() was added in nfsd and ksmbd code, but that
call is missing sb_start_write(), fsnotify hooks and more.
Ideally, nfsd and ksmbd would pass a flag to vfs_copy_file_range() that
will take care of the fallback, but that code would be subtle and we got
vfs_copy_file_range() logic wrong too many times already.
Instead, add a flag to explicitly request vfs_copy_file_range() to
perform only generic_copy_file_range() and let nfsd and ksmbd use this
flag only in the fallback path.
This choise keeps the logic changes to minimum in the non-nfsd/ksmbd code
paths to reduce the risk of further regressions.
Fixes: 868f9f2f8e00 ("vfs: fix copy_file_range() regression in cross-fs copies")
Tested-by: Namjae Jeon <linkinjeon@kernel.org>
Tested-by: Luis Henriques <lhenriques@suse.de>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[backport comments for v5.15: - sb_write_started() is missing - assert was dropped ]
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4a7ba45b1a435e7097ca0f79a847d0949d0eb088 upstream.
memcg_write_event_control() accesses the dentry->d_name of the specified
control fd to route the write call. As a cgroup interface file can't be
renamed, it's safe to access d_name as long as the specified file is a
regular cgroup file. Also, as these cgroup interface files can't be
removed before the directory, it's safe to access the parent too.
Prior to 347c4a874710 ("memcg: remove cgroup_event->cft"), there was a
call to __file_cft() which verified that the specified file is a regular
cgroupfs file before further accesses. The cftype pointer returned from
__file_cft() was no longer necessary and the commit inadvertently dropped
the file type check with it allowing any file to slip through. With the
invarients broken, the d_name and parent accesses can now race against
renames and removals of arbitrary files and cause use-after-free's.
Fix the bug by resurrecting the file type check in __file_cft(). Now that
cgroupfs is implemented through kernfs, checking the file operations needs
to go through a layer of indirection. Instead, let's check the superblock
and dentry type.
Link: https://lkml.kernel.org/r/Y5FRm/cfcKPGzWwl@slm.duckdns.org
Fixes: 347c4a874710 ("memcg: remove cgroup_event->cft")
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jann Horn <jannh@google.com>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: <stable@vger.kernel.org> [3.14+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ec5895c0f2d87b9bf4185db1915e40fa6fcfc0ac ]
Function mc146818_get_time() contains an elaborate mechanism of reading
the RTC time while no RTC update is in progress. It turns out that
reading the RTC alarm clock also requires avoiding the RTC update.
Therefore, the mechanism in mc146818_get_time() should be reused - so
extract it into a separate function.
The logic in mc146818_avoid_UIP() is same as in mc146818_get_time()
except that after every
if (CMOS_READ(RTC_FREQ_SELECT) & RTC_UIP) {
there is now "mdelay(1)".
To avoid producing a very unreadable patch, mc146818_get_time() will be
refactored to use mc146818_avoid_UIP() in the next patch.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-6-mat.jonczyk@o2.pl
Stable-dep-of: cd17420ebea5 ("rtc: cmos: avoid UIP when writing alarm time")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7ef9651e9792b08eb310c6beb202cbc947f43cab ]
When a driver keeps a clock prepared (or enabled) during the whole
lifetime of the driver, these helpers allow to simplify the drivers.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <aardelean@deviqon.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220520075737.758761-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stable-dep-of: c61bfb1cb63d ("mmc: mtk-sd: Fix missing clk_disable_unprepare in msdc_of_clock_parse()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 89f6c88a6ab4a11deb14c270f7f1454cda4f73d6 ]
__isolate_lru_page_prepare() conflates two unrelated functions, with the
flags to one disjoint from the flags to the other; and hides some of the
important checks outside of isolate_migratepages_block(), where the
sequence is better to be visible. It comes from the days of lumpy
reclaim, before compaction, when the combination made more sense.
Move what's needed by mm/compaction.c isolate_migratepages_block() inline
there, and what's needed by mm/vmscan.c isolate_lru_pages() inline there.
Shorten "isolate_mode" to "mode", so the sequence of conditions is easier
to read. Declare a "mapping" variable, to save one call to page_mapping()
(but not another: calling again after page is locked is necessary).
Simplify isolate_lru_pages() with a "move_to" list pointer.
Link: https://lkml.kernel.org/r/879d62a8-91cc-d3c6-fb3b-69768236df68@google.com
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Reviewed-by: Alex Shi <alexs@kernel.org>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stable-dep-of: 829ae0f81ce0 ("mm: migrate: fix THP's mapcount on isolation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 489d144563f23911262a652234b80c70c89c978b upstream.
Clean up the MMC_TRIM_ARGS define that became ambiguous with DISCARD
introduction. While at it, let's fix one usage where MMC_TRIM_ARGS falsely
included DISCARD too.
Fixes: b3bf915308ca ("mmc: core: new discard feature support at eMMC v4.5")
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/11376b5714964345908f3990f17e0701@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8925c31c1ac2f1e05da988581f2a70a2a8c4d638 ]
Preparing to move serial_rs485 struct sanitization into serial core,
each driver has to provide what fields/flags it supports. This
information is pointed into by rs485_supported.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 76bad3f88750 ("tty: serial: fsl_lpuart: don't break the on-going transfer when global reset")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e3e6e1d16a4cf7b63159ec71774e822194071954 upstream.
Syzkaller reports buffer overflow false positive as follows:
------------[ cut here ]------------
memcpy: detected field-spanning write (size 8) of single field
"&compat_event->pointer" at net/wireless/wext-core.c:623 (size 4)
WARNING: CPU: 0 PID: 3607 at net/wireless/wext-core.c:623
wireless_send_event+0xab5/0xca0 net/wireless/wext-core.c:623
Modules linked in:
CPU: 1 PID: 3607 Comm: syz-executor659 Not tainted
6.0.0-rc6-next-20220921-syzkaller #0
[...]
Call Trace:
<TASK>
ioctl_standard_call+0x155/0x1f0 net/wireless/wext-core.c:1022
wireless_process_ioctl+0xc8/0x4c0 net/wireless/wext-core.c:955
wext_ioctl_dispatch net/wireless/wext-core.c:988 [inline]
wext_ioctl_dispatch net/wireless/wext-core.c:976 [inline]
wext_handle_ioctl+0x26b/0x280 net/wireless/wext-core.c:1049
sock_ioctl+0x285/0x640 net/socket.c:1220
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl fs/ioctl.c:856 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
[...]
</TASK>
Wireless events will be sent on the appropriate channels in
wireless_send_event(). Different wireless events may have different
payload structure and size, so kernel uses **len** and **cmd** field
in struct __compat_iw_event as wireless event common LCP part, uses
**pointer** as a label to mark the position of remaining different part.
Yet the problem is that, **pointer** is a compat_caddr_t type, which may
be smaller than the relative structure at the same position. So during
wireless_send_event() tries to parse the wireless events payload, it may
trigger the memcpy() run-time destination buffer bounds checking when the
relative structure's data is copied to the position marked by **pointer**.
This patch solves it by introducing flexible-array field **ptr_bytes**,
to mark the position of the wireless events remaining part next to
LCP part. What's more, this patch also adds **ptr_len** variable in
wireless_send_event() to improve its maintainability.
Reported-and-tested-by: syzbot+473754e5af963cf014cf@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/00000000000070db2005e95a5984@google.com/
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bedf06833b1f63c2627bd5634602e05592129d7a ]
Move the declaration of 'struct trace_array' out of #ifdef
CONFIG_TRACING block, to fix the following warning when CONFIG_TRACING
is not set:
>> include/linux/trace.h:63:45: warning: 'struct trace_array' declared
inside parameter list will not be visible outside of this definition or
declaration
Link: https://lkml.kernel.org/r/20221107160556.2139463-1-shraash@google.com
Fixes: 1a77dd1c2bb5 ("scsi: tracing: Fix compile error in trace_array calls when TRACING is disabled")
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Arun Easi <aeasi@marvell.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Aashish Sharma <shraash@google.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 42fb0a1e84ff525ebe560e2baf9451ab69127e2b upstream.
Currently the way polling works on the ring buffer is broken. It will
return immediately if there's any data in the ring buffer whereas a read
will block until the watermark (defined by the tracefs buffer_percent file)
is hit.
That is, a select() or poll() will return as if there's data available,
but then the following read will block. This is broken for the way
select()s and poll()s are supposed to work.
Have the polling on the ring buffer also block the same way reads and
splice does on the ring buffer.
Link: https://lkml.kernel.org/r/20221020231427.41be3f26@gandalf.local.home
Cc: Linux Trace Kernel <linux-trace-kernel@vger.kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Primiano Tucci <primiano@google.com>
Cc: stable@vger.kernel.org
Fixes: 1e0d6714aceb7 ("ring-buffer: Do not wake up a splice waiter when page is not full")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cd149eff8d2201a63c074a6d9d03e52926aa535d ]
Currently the driver tries to disable the BIOS write protection
automatically even if this is not what the user wants. For this reason
modify the driver so that by default it does not touch the write
protection. Only if specifically asked by the user (setting writeable=1
command line parameter) the driver tries to disable the BIOS write
protection.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220209122706.42439-2-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 92a66cbf6b30 ("spi: intel: Use correct mask for flash and protected regions")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 6312d52838b21f5c4a5afa1269a00df4364fd354 upstream.
Building an allmodconfig kernel arm64 kernel, the following build error
shows up:
In file included from drivers/crypto/marvell/octeontx2/cn10k_cpt.c:4:
include/linux/soc/marvell/octeontx2/asm.h:38:15: error: unknown type name 'u64'
38 | static inline u64 otx2_atomic64_fetch_add(u64 incr, u64 *ptr)
| ^~~
Include linux/types.h in asm.h so the compiler knows what the type
'u64' are.
Fixes: af3826db74d1 ("octeontx2-pf: Use hardware register for CQE count")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20211013135743.3826594-1-anders.roxell@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit af3826db74d184bc9c2c9d3ff34548e5f317a6f3 ]
Current driver uses software CQ head pointer to poll on CQE
header in memory to determine if CQE is valid. Software needs
to make sure, that the reads of the CQE do not get re-ordered
so much that it ends up with an inconsistent view of the CQE.
To ensure that DMB barrier after read to first CQE cacheline
and before reading of the rest of the CQE is needed.
But having barrier for every CQE read will impact the performance,
instead use hardware CQ head and tail pointers to find the
valid number of CQEs.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 51afe9026d0c ("octeontx2-pf: NIX TX overwrites SQ_CTX_HW_S[SQ_INT]")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b239da34203f49c40b5d656220c39647c3ff0b3c ]
For a lot of use cases in future patches, we will want to modify the
state of registers part of some same 'group' (e.g. same ref_obj_id). It
won't just be limited to releasing reference state, but setting a type
flag dynamically based on certain actions, etc.
Hence, we need a way to easily pass a callback to the function that
iterates over all registers in current bpf_verifier_state in all frames
upto (and including) the curframe.
While in C++ we would be able to easily use a lambda to pass state and
the callback together, sadly we aren't using C++ in the kernel. The next
best thing to avoid defining a function for each case seems like
statement expressions in GNU C. The kernel already uses them heavily,
hence they can passed to the macro in the style of a lambda. The
statement expression will then be substituted in the for loop bodies.
Variables __state and __reg are set to current bpf_func_state and reg
for each invocation of the expression inside the passed in verifier
state.
Then, convert mark_ptr_or_null_regs, clear_all_pkt_pointers,
release_reference, find_good_pkt_pointers, find_equal_scalars to
use bpf_for_each_reg_in_vstate.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220904204145.3089-16-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: f1db20814af5 ("bpf: Fix wrong reg type conversion in release_reference()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8bbabb3fddcd0f858be69ed5abc9b470a239d6f2 ]
Stanislav reported a lockdep warning, which is caused by the
cancel_work_sync() called inside sock_map_close(), as analyzed
below by Jakub:
psock->work.func = sk_psock_backlog()
ACQUIRE psock->work_mutex
sk_psock_handle_skb()
skb_send_sock()
__skb_send_sock()
sendpage_unlocked()
kernel_sendpage()
sock->ops->sendpage = inet_sendpage()
sk->sk_prot->sendpage = tcp_sendpage()
ACQUIRE sk->sk_lock
tcp_sendpage_locked()
RELEASE sk->sk_lock
RELEASE psock->work_mutex
sock_map_close()
ACQUIRE sk->sk_lock
sk_psock_stop()
sk_psock_clear_state(psock, SK_PSOCK_TX_ENABLED)
cancel_work_sync()
__cancel_work_timer()
__flush_work()
// wait for psock->work to finish
RELEASE sk->sk_lock
We can move the cancel_work_sync() out of the sock lock protection,
but still before saved_close() was called.
Fixes: 799aa7f98d53 ("skmsg: Avoid lock_sock() in sk_psock_backlog()")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20221102043417.279409-1-xiyou.wangcong@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d8616ee2affcff37c5d315310da557a694a3303d ]
During TCP sockmap redirect pressure test, the following warning is triggered:
WARNING: CPU: 3 PID: 2145 at net/core/stream.c:205 sk_stream_kill_queues+0xbc/0xd0
CPU: 3 PID: 2145 Comm: iperf Kdump: loaded Tainted: G W 5.10.0+ #9
Call Trace:
inet_csk_destroy_sock+0x55/0x110
inet_csk_listen_stop+0xbb/0x380
tcp_close+0x41b/0x480
inet_release+0x42/0x80
__sock_release+0x3d/0xa0
sock_close+0x11/0x20
__fput+0x9d/0x240
task_work_run+0x62/0x90
exit_to_user_mode_prepare+0x110/0x120
syscall_exit_to_user_mode+0x27/0x190
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The reason we observed is that:
When the listener is closing, a connection may have completed the three-way
handshake but not accepted, and the client has sent some packets. The child
sks in accept queue release by inet_child_forget()->inet_csk_destroy_sock(),
but psocks of child sks have not released.
To fix, add sock_map_destroy to release psocks.
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220524075311.649153-1-wangyufen@huawei.com
Stable-dep-of: 8bbabb3fddcd ("bpf, sock_map: Move cancel_work_sync() out of sock lock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 161a438d730dade2ba2b1bf8785f0759aba4ca5f upstream.
We no longer need at least 64 bytes of random seed to permit the early
crng init to complete. The RNG is now based on Blake2s, so reduce the
EFI seed size to the Blake2s hash size, which is sufficient for our
purposes.
While at it, drop the READ_ONCE(), which was supposed to prevent size
from being evaluated after seed was unmapped. However, this cannot
actually happen, so READ_ONCE() is unnecessary here.
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ccd30a476f8e864732de220bd50e6f372f5ebcab upstream.
Commit d7e7b9af104c ("fscrypt: stop using keyrings subsystem for
fscrypt_master_key") moved the keyring destruction from __put_super() to
generic_shutdown_super() so that the filesystem's block device(s) are
still available. Unfortunately, this causes a memory leak in the case
where a mount is attempted with the test_dummy_encryption mount option,
but the mount fails after the option has already been processed.
To fix this, attempt the keyring destruction in both places.
Reported-by: syzbot+104c2a89561289cec13e@syzkaller.appspotmail.com
Fixes: d7e7b9af104c ("fscrypt: stop using keyrings subsystem for fscrypt_master_key")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Link: https://lore.kernel.org/r/20221011213838.209879-1-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d7e7b9af104c7b389a0c21eb26532511bce4b510 upstream.
The approach of fs/crypto/ internally managing the fscrypt_master_key
structs as the payloads of "struct key" objects contained in a
"struct key" keyring has outlived its usefulness. The original idea was
to simplify the code by reusing code from the keyrings subsystem.
However, several issues have arisen that can't easily be resolved:
- When a master key struct is destroyed, blk_crypto_evict_key() must be
called on any per-mode keys embedded in it. (This started being the
case when inline encryption support was added.) Yet, the keyrings
subsystem can arbitrarily delay the destruction of keys, even past the
time the filesystem was unmounted. Therefore, currently there is no
easy way to call blk_crypto_evict_key() when a master key is
destroyed. Currently, this is worked around by holding an extra
reference to the filesystem's request_queue(s). But it was overlooked
that the request_queue reference is *not* guaranteed to pin the
corresponding blk_crypto_profile too; for device-mapper devices that
support inline crypto, it doesn't. This can cause a use-after-free.
- When the last inode that was using an incompletely-removed master key
is evicted, the master key removal is completed by removing the key
struct from the keyring. Currently this is done via key_invalidate().
Yet, key_invalidate() takes the key semaphore. This can deadlock when
called from the shrinker, since in fscrypt_ioctl_add_key(), memory is
allocated with GFP_KERNEL under the same semaphore.
- More generally, the fact that the keyrings subsystem can arbitrarily
delay the destruction of keys (via garbage collection delay, or via
random processes getting temporary key references) is undesirable, as
it means we can't strictly guarantee that all secrets are ever wiped.
- Doing the master key lookups via the keyrings subsystem results in the
key_permission LSM hook being called. fscrypt doesn't want this, as
all access control for encrypted files is designed to happen via the
files themselves, like any other files. The workaround which SELinux
users are using is to change their SELinux policy to grant key search
access to all domains. This works, but it is an odd extra step that
shouldn't really have to be done.
The fix for all these issues is to change the implementation to what I
should have done originally: don't use the keyrings subsystem to keep
track of the filesystem's fscrypt_master_key structs. Instead, just
store them in a regular kernel data structure, and rework the reference
counting, locking, and lifetime accordingly. Retain support for
RCU-mode key lookups by using a hash table. Replace fscrypt_sb_free()
with fscrypt_sb_delete(), which releases the keys synchronously and runs
a bit earlier during unmount, so that block devices are still available.
A side effect of this patch is that neither the master keys themselves
nor the filesystem keyrings will be listed in /proc/keys anymore.
("Master key users" and the master key users keyrings will still be
listed.) However, this was mostly an implementation detail, and it was
intended just for debugging purposes. I don't know of anyone using it.
This patch does *not* change how "master key users" (->mk_users) works;
that still uses the keyrings subsystem. That is still needed for key
quotas, and changing that isn't necessary to solve the issues listed
above. If we decide to change that too, it would be a separate patch.
I've marked this as fixing the original commit that added the fscrypt
keyring, but as noted above the most important issue that this patch
fixes wasn't introduced until the addition of inline encryption support.
Fixes: 22d94f493bfb ("fscrypt: add FS_IOC_ADD_ENCRYPTION_KEY ioctl")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20220901193208.138056-2-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fac35ba763ed07ba93154c95ffc0c4a55023707f ]
On some architectures (like ARM64), it can support CONT-PTE/PMD size
hugetlb, which means it can support not only PMD/PUD size hugetlb (2M and
1G), but also CONT-PTE/PMD size(64K and 32M) if a 4K page size specified.
So when looking up a CONT-PTE size hugetlb page by follow_page(), it will
use pte_offset_map_lock() to get the pte entry lock for the CONT-PTE size
hugetlb in follow_page_pte(). However this pte entry lock is incorrect
for the CONT-PTE size hugetlb, since we should use huge_pte_lock() to get
the correct lock, which is mm->page_table_lock.
That means the pte entry of the CONT-PTE size hugetlb under current pte
lock is unstable in follow_page_pte(), we can continue to migrate or
poison the pte entry of the CONT-PTE size hugetlb, which can cause some
potential race issues, even though they are under the 'pte lock'.
For example, suppose thread A is trying to look up a CONT-PTE size hugetlb
page by move_pages() syscall under the lock, however antoher thread B can
migrate the CONT-PTE hugetlb page at the same time, which will cause
thread A to get an incorrect page, if thread A also wants to do page
migration, then data inconsistency error occurs.
Moreover we have the same issue for CONT-PMD size hugetlb in
follow_huge_pmd().
To fix above issues, rename the follow_huge_pmd() as follow_huge_pmd_pte()
to handle PMD and PTE level size hugetlb, which uses huge_pte_lock() to
get the correct pte entry lock to make the pte entry stable.
Mike said:
Support for CONT_PMD/_PTE was added with bb9dd3df8ee9 ("arm64: hugetlb:
refactor find_num_contig()"). Patch series "Support for contiguous pte
hugepages", v4. However, I do not believe these code paths were
executed until migration support was added with 5480280d3f2d ("arm64/mm:
enable HugeTLB migration for contiguous bit HugeTLB pages") I would go
with 5480280d3f2d for the Fixes: targe.
Link: https://lkml.kernel.org/r/635f43bdd85ac2615a58405da82b4d33c6e5eb05.1662017562.git.baolin.wang@linux.alibaba.com
Fixes: 5480280d3f2d ("arm64/mm: enable HugeTLB migration for contiguous bit HugeTLB pages")
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Suggested-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bacd22df95147ed673bec4692ab2d4d585935241 ]
mlx5_cmd_cleanup_async_ctx should return only after all its callback
handlers were completed. Before this patch, the below race between
mlx5_cmd_cleanup_async_ctx and mlx5_cmd_exec_cb_handler was possible and
lead to a use-after-free:
1. mlx5_cmd_cleanup_async_ctx is called while num_inflight is 2 (i.e.
elevated by 1, a single inflight callback).
2. mlx5_cmd_cleanup_async_ctx decreases num_inflight to 1.
3. mlx5_cmd_exec_cb_handler is called, decreases num_inflight to 0 and
is about to call wake_up().
4. mlx5_cmd_cleanup_async_ctx calls wait_event, which returns
immediately as the condition (num_inflight == 0) holds.
5. mlx5_cmd_cleanup_async_ctx returns.
6. The caller of mlx5_cmd_cleanup_async_ctx frees the mlx5_async_ctx
object.
7. mlx5_cmd_exec_cb_handler goes on and calls wake_up() on the freed
object.
Fix it by syncing using a completion object. Mark it completed when
num_inflight reaches 0.
Trace:
BUG: KASAN: use-after-free in do_raw_spin_lock+0x23d/0x270
Read of size 4 at addr ffff888139cd12f4 by task swapper/5/0
CPU: 5 PID: 0 Comm: swapper/5 Not tainted 6.0.0-rc3_for_upstream_debug_2022_08_30_13_10 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x57/0x7d
print_report.cold+0x2d5/0x684
? do_raw_spin_lock+0x23d/0x270
kasan_report+0xb1/0x1a0
? do_raw_spin_lock+0x23d/0x270
do_raw_spin_lock+0x23d/0x270
? rwlock_bug.part.0+0x90/0x90
? __delete_object+0xb8/0x100
? lock_downgrade+0x6e0/0x6e0
_raw_spin_lock_irqsave+0x43/0x60
? __wake_up_common_lock+0xb9/0x140
__wake_up_common_lock+0xb9/0x140
? __wake_up_common+0x650/0x650
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kasan_set_track+0x21/0x30
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kfree+0x1ba/0x520
? do_raw_spin_unlock+0x54/0x220
mlx5_cmd_exec_cb_handler+0x136/0x1a0 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
mlx5_cmd_comp_handler+0x65a/0x12b0 [mlx5_core]
? dump_command+0xcc0/0xcc0 [mlx5_core]
? lockdep_hardirqs_on_prepare+0x400/0x400
? cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
mlx5_eq_async_int+0x3ce/0xa20 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
? irq_release+0x140/0x140 [mlx5_core]
irq_int_handler+0x19/0x30 [mlx5_core]
__handle_irq_event_percpu+0x1f2/0x620
handle_irq_event+0xb2/0x1d0
handle_edge_irq+0x21e/0xb00
__common_interrupt+0x79/0x1a0
common_interrupt+0x78/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:default_idle+0x42/0x60
Code: c1 83 e0 07 48 c1 e9 03 83 c0 03 0f b6 14 11 38 d0 7c 04 84 d2 75 14 8b 05 eb 47 22 02 85 c0 7e 07 0f 00 2d e0 9f 48 00 fb f4 <c3> 48 c7 c7 80 08 7f 85 e8 d1 d3 3e fe eb de 66 66 2e 0f 1f 84 00
RSP: 0018:ffff888100dbfdf0 EFLAGS: 00000242
RAX: 0000000000000001 RBX: ffffffff84ecbd48 RCX: 1ffffffff0afe110
RDX: 0000000000000004 RSI: 0000000000000000 RDI: ffffffff835cc9bc
RBP: 0000000000000005 R08: 0000000000000001 R09: ffff88881dec4ac3
R10: ffffed1103bd8958 R11: 0000017d0ca571c9 R12: 0000000000000005
R13: ffffffff84f024e0 R14: 0000000000000000 R15: dffffc0000000000
? default_idle_call+0xcc/0x450
default_idle_call+0xec/0x450
do_idle+0x394/0x450
? arch_cpu_idle_exit+0x40/0x40
? do_idle+0x17/0x450
cpu_startup_entry+0x19/0x20
start_secondary+0x221/0x2b0
? set_cpu_sibling_map+0x2070/0x2070
secondary_startup_64_no_verify+0xcd/0xdb
</TASK>
Allocated by task 49502:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0x81/0xa0
kvmalloc_node+0x48/0xe0
mlx5e_bulk_async_init+0x35/0x110 [mlx5_core]
mlx5e_tls_priv_tx_list_cleanup+0x84/0x3e0 [mlx5_core]
mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core]
mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core]
mlx5e_detach_netdev+0x1ca/0x2b0 [mlx5_core]
mlx5e_suspend+0xdb/0x140 [mlx5_core]
mlx5e_remove+0x89/0x190 [mlx5_core]
auxiliary_bus_remove+0x52/0x70
device_release_driver_internal+0x40f/0x650
driver_detach+0xc1/0x180
bus_remove_driver+0x125/0x2f0
auxiliary_driver_unregister+0x16/0x50
mlx5e_cleanup+0x26/0x30 [mlx5_core]
cleanup+0xc/0x4e [mlx5_core]
__x64_sys_delete_module+0x2b5/0x450
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Freed by task 49502:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_set_free_info+0x20/0x30
____kasan_slab_free+0x11d/0x1b0
kfree+0x1ba/0x520
mlx5e_tls_priv_tx_list_cleanup+0x2e7/0x3e0 [mlx5_core]
mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core]
mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core]
mlx5e_detach_netdev+0x1ca/0x2b0 [mlx5_core]
mlx5e_suspend+0xdb/0x140 [mlx5_core]
mlx5e_remove+0x89/0x190 [mlx5_core]
auxiliary_bus_remove+0x52/0x70
device_release_driver_internal+0x40f/0x650
driver_detach+0xc1/0x180
bus_remove_driver+0x125/0x2f0
auxiliary_driver_unregister+0x16/0x50
mlx5e_cleanup+0x26/0x30 [mlx5_core]
cleanup+0xc/0x4e [mlx5_core]
__x64_sys_delete_module+0x2b5/0x450
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: e355477ed9e4 ("net/mlx5: Make mlx5_cmd_exec_cb() a safe API")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-8-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ca6c21327c6af02b7eec31ce4b9a740a18c6c13f ]
Marco reported:
Due to the implementation of how SIGTRAP are delivered if
perf_event_attr::sigtrap is set, we've noticed 3 issues:
1. Missing SIGTRAP due to a race with event_sched_out() (more
details below).
2. Hardware PMU events being disabled due to returning 1 from
perf_event_overflow(). The only way to re-enable the event is
for user space to first "properly" disable the event and then
re-enable it.
3. The inability to automatically disable an event after a
specified number of overflows via PERF_EVENT_IOC_REFRESH.
The worst of the 3 issues is problem (1), which occurs when a
pending_disable is "consumed" by a racing event_sched_out(), observed
as follows:
CPU0 | CPU1
--------------------------------+---------------------------
__perf_event_overflow() |
perf_event_disable_inatomic() |
pending_disable = CPU0 | ...
| _perf_event_enable()
| event_function_call()
| task_function_call()
| /* sends IPI to CPU0 */
<IPI> | ...
__perf_event_enable() +---------------------------
ctx_resched()
task_ctx_sched_out()
ctx_sched_out()
group_sched_out()
event_sched_out()
pending_disable = -1
</IPI>
<IRQ-work>
perf_pending_event()
perf_pending_event_disable()
/* Fails to send SIGTRAP because no pending_disable! */
</IRQ-work>
In the above case, not only is that particular SIGTRAP missed, but also
all future SIGTRAPs because 'event_limit' is not reset back to 1.
To fix, rework pending delivery of SIGTRAP via IRQ-work by introduction
of a separate 'pending_sigtrap', no longer using 'event_limit' and
'pending_disable' for its delivery.
Additionally; and different to Marco's proposed patch:
- recognise that pending_disable effectively duplicates oncpu for
the case where it is set. As such, change the irq_work handler to
use ->oncpu to target the event and use pending_* as boolean toggles.
- observe that SIGTRAP targets the ctx->task, so the context switch
optimization that carries contexts between tasks is invalid. If
the irq_work were delayed enough to hit after a context switch the
SIGTRAP would be delivered to the wrong task.
- observe that if the event gets scheduled out
(rotation/migration/context-switch/...) the irq-work would be
insufficient to deliver the SIGTRAP when the event gets scheduled
back in (the irq-work might still be pending on the old CPU).
Therefore have event_sched_out() convert the pending sigtrap into a
task_work which will deliver the signal at return_to_user.
Fixes: 97ba62b27867 ("perf: Add support for SIGTRAP on perf events")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Debugged-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Marco Elver <elver@google.com>
Debugged-by: Marco Elver <elver@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Marco Elver <elver@google.com>
Tested-by: Marco Elver <elver@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
