| Age | Commit message (Collapse) | Author |
|
[ Upstream commit 05d6d492097c55f2d153fc3fd33cbe78e1e28e0a ]
I added dst_rt6_info() in commit
e8dfd42c17fa ("ipv6: introduce dst_rt6_info() helper")
This patch does a similar change for IPv4.
Instead of (struct rtable *)dst casts, we can use :
#define dst_rtable(_ptr) \
container_of_const(_ptr, struct rtable, dst)
Patch is smaller than IPv6 one, because IPv4 has skb_rtable() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240429133009.1227754-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 92f1655aa2b2 ("net: fix __dst_negative_advice() race")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3998d184267dfcff858aaa84d3de17429253629d ]
When running Cilium connectivity test suite with netkit in L2 mode, we
found that compared to tcx a few tests were failing which pushed traffic
into an L7 proxy sitting in host namespace. The problem in particular is
around the invocation of eth_type_trans() in netkit.
In case of tcx, this is run before the tcx ingress is triggered inside
host namespace and thus if the BPF program uses the bpf_skb_change_type()
helper the newly set type is retained. However, in case of netkit, the
late eth_type_trans() invocation overrides the earlier decision from the
BPF program which eventually leads to the test failure.
Instead of eth_type_trans(), split out the relevant parts, meaning, reset
of mac header and call to eth_skb_pkt_type() before the BPF program is run
in order to have the same behavior as with tcx, and refactor a small helper
called eth_skb_pull_mac() which is run in case it's passed up the stack
where the mac header must be pulled. With this all connectivity tests pass.
Fixes: 35dfaad7188c ("netkit, bpf: Add bpf programmable net device")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20240524163619.26001-2-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1b9f86c6d53245dab087f1b2c05727b5982142ff ]
The MTMP register (0x900a) capability offset is off-by-one, move it to
the right place.
Fixes: 1f507e80c700 ("net/mlx5: Expose NIC temperature via hardware monitoring kernel API")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2e577732e8d28b9183df701fb90cb7943aa4ed16 ]
After commit 69d4c0d32186 ("entry, kasan, x86: Disallow overriding mem*()
functions") and the follow-up fixes, with CONFIG_FORTIFY_SOURCE enabled,
even though the compiler instruments meminstrinsics by generating calls to
__asan/__hwasan_ prefixed functions, FORTIFY_SOURCE still uses
uninstrumented memset/memmove/memcpy as the underlying functions.
As a result, KASAN cannot detect bad accesses in memset/memmove/memcpy.
This also makes KASAN tests corrupt kernel memory and cause crashes.
To fix this, use __asan_/__hwasan_memset/memmove/memcpy as the underlying
functions whenever appropriate. Do this only for the instrumented code
(as indicated by __SANITIZE_ADDRESS__).
Link: https://lkml.kernel.org/r/20240517130118.759301-1-andrey.konovalov@linux.dev
Fixes: 69d4c0d32186 ("entry, kasan, x86: Disallow overriding mem*() functions")
Fixes: 51287dcb00cc ("kasan: emit different calls for instrumentable memintrinsics")
Fixes: 36be5cba99f6 ("kasan: treat meminstrinsic as builtins in uninstrumented files")
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Reported-by: Erhard Furtner <erhard_f@mailbox.org>
Reported-by: Nico Pache <npache@redhat.com>
Closes: https://lore.kernel.org/all/20240501144156.17e65021@outsider.home/
Reviewed-by: Marco Elver <elver@google.com>
Tested-by: Nico Pache <npache@redhat.com>
Acked-by: Nico Pache <npache@redhat.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f4f4276f985a5aac7b310a4ed040b47e275e7591 ]
Some PMICs treat the vsel_reg same as apply-bit. Eg, when voltage range
is changed, the new voltage setting is not taking effect until the vsel
register is written.
Add a flag 'range_applied_by_vsel' to the regulator desc to indicate this
behaviour and to force the vsel value to be written to hardware if range
was changed, even if the old selector was same as the new one.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://msgid.link/r/ZktCpcGZdgHWuN_L@fedora
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 1ace99d7c7c4 ("regulator: tps6287x: Force writing VSEL bit")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b7c0e1ecee403a43abc89eb3e75672b01ff2ece9 ]
The current implementation of the fpga region assumes that the low-level
module registers a driver for the parent device and uses its owner pointer
to take the module's refcount. This approach is problematic since it can
lead to a null pointer dereference while attempting to get the region
during programming if the parent device does not have a driver.
To address this problem, add a module owner pointer to the fpga_region
struct and use it to take the module's refcount. Modify the functions for
registering a region to take an additional owner module parameter and
rename them to avoid conflicts. Use the old function names for helper
macros that automatically set the module that registers the region as the
owner. This ensures compatibility with existing low-level control modules
and reduces the chances of registering a region without setting the owner.
Also, update the documentation to keep it consistent with the new interface
for registering an fpga region.
Fixes: 0fa20cdfcc1f ("fpga: fpga-region: device tree control for FPGA")
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Russ Weight <russ.weight@linux.dev>
Signed-off-by: Marco Pagani <marpagan@redhat.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20240419083601.77403-1-marpagan@redhat.com
Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 416bdb89605d960405178b9bf04df512d1ace1a3 ]
Remove the @priv: line to prevent the kernel-doc warning:
include/linux/counter.h:400: warning: Excess struct member 'priv' description in 'counter_device'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: f2ee4759fb70 ("counter: remove old and now unused registration API")
Link: https://lore.kernel.org/r/20231223050511.13849-1-rdunlap@infradead.org
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1da11f822042eb6ef4b6064dc048f157a7852529 ]
The current implementation of the fpga bridge assumes that the low-level
module registers a driver for the parent device and uses its owner pointer
to take the module's refcount. This approach is problematic since it can
lead to a null pointer dereference while attempting to get the bridge if
the parent device does not have a driver.
To address this problem, add a module owner pointer to the fpga_bridge
struct and use it to take the module's refcount. Modify the function for
registering a bridge to take an additional owner module parameter and
rename it to avoid conflicts. Use the old function name for a helper macro
that automatically sets the module that registers the bridge as the owner.
This ensures compatibility with existing low-level control modules and
reduces the chances of registering a bridge without setting the owner.
Also, update the documentation to keep it consistent with the new interface
for registering an fpga bridge.
Other changes: opportunistically move put_device() from __fpga_bridge_get()
to fpga_bridge_get() and of_fpga_bridge_get() to improve code clarity since
the bridge device is taken in these functions.
Fixes: 21aeda950c5f ("fpga: add fpga bridge framework")
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Russ Weight <russ.weight@linux.dev>
Signed-off-by: Marco Pagani <marpagan@redhat.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20240322171839.233864-1-marpagan@redhat.com
Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4d4d2d4346857bf778fafaa97d6f76bb1663e3c9 ]
The current implementation of the fpga manager assumes that the low-level
module registers a driver for the parent device and uses its owner pointer
to take the module's refcount. This approach is problematic since it can
lead to a null pointer dereference while attempting to get the manager if
the parent device does not have a driver.
To address this problem, add a module owner pointer to the fpga_manager
struct and use it to take the module's refcount. Modify the functions for
registering the manager to take an additional owner module parameter and
rename them to avoid conflicts. Use the old function names for helper
macros that automatically set the module that registers the manager as the
owner. This ensures compatibility with existing low-level control modules
and reduces the chances of registering a manager without setting the owner.
Also, update the documentation to keep it consistent with the new interface
for registering an fpga manager.
Other changes: opportunistically move put_device() from __fpga_mgr_get() to
fpga_mgr_get() and of_fpga_mgr_get() to improve code clarity since the
manager device is taken in these functions.
Fixes: 654ba4cc0f3e ("fpga manager: ensure lifetime with of_fpga_mgr_get")
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Marco Pagani <marpagan@redhat.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20240305192926.84886-1-marpagan@redhat.com
Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3a9e567ca45fb5280065283d10d9a11f0db61d2b ]
Patch series "mm/ksm: fix ksm exec support for prctl", v4.
commit 3c6f33b7273a ("mm/ksm: support fork/exec for prctl") inherits
MMF_VM_MERGE_ANY flag when a task calls execve(). However, it doesn't
create the mm_slot, so ksmd will not try to scan this task. The first
patch fixes the issue.
The second patch refactors to prepare for the third patch. The third
patch extends the selftests of ksm to verfity the deduplication really
happens after fork/exec inherits ths KSM setting.
This patch (of 3):
commit 3c6f33b7273a ("mm/ksm: support fork/exec for prctl") inherits
MMF_VM_MERGE_ANY flag when a task calls execve(). Howerver, it doesn't
create the mm_slot, so ksmd will not try to scan this task.
To fix it, allocate and add the mm_slot to ksm_mm_head in __bprm_mm_init()
when the mm has MMF_VM_MERGE_ANY flag.
Link: https://lkml.kernel.org/r/20240328111010.1502191-1-tujinjiang@huawei.com
Link: https://lkml.kernel.org/r/20240328111010.1502191-2-tujinjiang@huawei.com
Fixes: 3c6f33b7273a ("mm/ksm: support fork/exec for prctl")
Signed-off-by: Jinjiang Tu <tujinjiang@huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Nanyong Sun <sunnanyong@huawei.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Stefan Roesch <shr@devkernel.io>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c26ec799042a3888935d59b599f33e41efedf5f8 ]
When printk-indexing is enabled, each dev_printk() invocation emits a
pi_entry structure. This is even true when the dev_printk() is
protected by an always-false check, as is typically the case for debug
messages: while the actual code to print the message is optimized out by
the compiler, the pi_entry structure is still emitted.
Avoid emitting pi_entry structures for unavailable dev_printk() kernel
messages by:
1. Introducing a dev_no_printk() helper, mimicked after the existing
no_printk() helper, which calls _dev_printk() instead of
dev_printk(),
2. Replacing all "if (0) dev_printk(...)" constructs by calls to the
new helper.
This reduces the size of an arm64 defconfig kernel with
CONFIG_PRINTK_INDEX=y by 957 KiB.
Fixes: ad7d61f159db7397 ("printk: index: Add indexing support to dev_printk")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Chris Down <chris@chrisdown.name>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/8583d54f1687c801c6cda8edddf2cf0344c6e883.1709127473.git.geert+renesas@glider.be
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8522f6b760ca588928eede740d5d69dd1e936b49 ]
When printk-indexing is enabled, each printk() invocation emits a
pi_entry structure, containing the format string and other information
related to its location in the kernel sources. This is even true for
no_printk(): while the actual code to print the message is optimized out
by the compiler due to the always-false check, the pi_entry structure is
still emitted.
As the main purpose of no_printk() is to provide a helper to maintain
printf()-style format checking when debugging is disabled, this leads to
the inclusion in the index of lots of printk formats that cannot be
emitted by the current kernel.
Fix this by switching no_printk() from printk() to _printk().
This reduces the size of an arm64 defconfig kernel with
CONFIG_PRINTK_INDEX=y by 576 KiB.
Fixes: 337015573718b161 ("printk: Userspace format indexing support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Chris Down <chris@chrisdown.name>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/56cf92edccffea970e1f40a075334dd6cf5bb2a4.1709127473.git.geert+renesas@glider.be
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 01c0cce88c5480cc2505b79330246ef12eda938f ]
Commit 95da53d63dcf ("drm/omapdrm: Use regular fbdev I/O helpers")
stopped console from updating for command mode displays because there is
no damage handling in fb_sys_write() unlike we had earlier in
drm_fb_helper_sys_write().
Let's fix the issue by adding FB_GEN_DEFAULT_DEFERRED_DMAMEM_OPS and
FB_DMAMEM_HELPERS_DEFERRED as suggested by Thomas. We cannot use the
FB_DEFAULT_DEFERRED_OPS as fb_deferred_io_mmap() won't work properly
for write-combine.
Fixes: 95da53d63dcf ("drm/omapdrm: Use regular fbdev I/O helpers")
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240228063540.4444-3-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 36ac9e7f2e5786bd37c5cd91132e1f39c29b8197 ]
Reinitialize the whole EST structure would also reset the mutex
lock which is embedded in the EST structure, and then trigger
the following warning. To address this, move the lock to struct
stmmac_priv. We also need to reacquire the mutex lock when doing
this initialization.
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 3 PID: 505 at kernel/locking/mutex.c:587 __mutex_lock+0xd84/0x1068
Modules linked in:
CPU: 3 PID: 505 Comm: tc Not tainted 6.9.0-rc6-00053-g0106679839f7-dirty #29
Hardware name: NXP i.MX8MPlus EVK board (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __mutex_lock+0xd84/0x1068
lr : __mutex_lock+0xd84/0x1068
sp : ffffffc0864e3570
x29: ffffffc0864e3570 x28: ffffffc0817bdc78 x27: 0000000000000003
x26: ffffff80c54f1808 x25: ffffff80c9164080 x24: ffffffc080d723ac
x23: 0000000000000000 x22: 0000000000000002 x21: 0000000000000000
x20: 0000000000000000 x19: ffffffc083bc3000 x18: ffffffffffffffff
x17: ffffffc08117b080 x16: 0000000000000002 x15: ffffff80d2d40000
x14: 00000000000002da x13: ffffff80d2d404b8 x12: ffffffc082b5a5c8
x11: ffffffc082bca680 x10: ffffffc082bb2640 x9 : ffffffc082bb2698
x8 : 0000000000017fe8 x7 : c0000000ffffefff x6 : 0000000000000001
x5 : ffffff8178fe0d48 x4 : 0000000000000000 x3 : 0000000000000027
x2 : ffffff8178fe0d50 x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
__mutex_lock+0xd84/0x1068
mutex_lock_nested+0x28/0x34
tc_setup_taprio+0x118/0x68c
stmmac_setup_tc+0x50/0xf0
taprio_change+0x868/0xc9c
Fixes: b2aae654a479 ("net: stmmac: add mutex lock to protect est parameters")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240513014346.1718740-2-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 485d65e1357123a697c591a5aeb773994b247ad7 ]
Prevent forced completion handling on an entry that has not yet been
assigned an index, causing an out of bounds access on idx = -22.
Instead of waiting indefinitely for the sem, blocking flow now waits for
index to be allocated or a sem acquisition timeout before beginning the
timer for FW completion.
Kernel log example:
mlx5_core 0000:06:00.0: wait_func_handle_exec_timeout:1128:(pid 185911): cmd[-22]: CREATE_UCTX(0xa04) No done completion
Fixes: 8e715cd613a1 ("net/mlx5: Set command entry semaphore up once got index free")
Signed-off-by: Akiva Goldberger <agoldberger@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240509112951.590184-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f9f67e5adc8dc2e1cc51ab2d3d6382fa97f074d4 ]
For configurations that have the kconfig option NUMA_KEEP_MEMINFO
disabled, numa_fill_memblks() only returns with NUMA_NO_MEMBLK (-1).
SRAT lookup fails then because an existing SRAT memory range cannot be
found for a CFMWS address range. This causes the addition of a
duplicate numa_memblk with a different node id and a subsequent page
fault and kernel crash during boot.
Fix this by making numa_fill_memblks() always available regardless of
NUMA_KEEP_MEMINFO.
As Dan suggested, the fix is implemented to remove numa_fill_memblks()
from sparsemem.h and alos using __weak for the function.
Note that the issue was initially introduced with [1]. But since
phys_to_target_node() was originally used that returned the valid node
0, an additional numa_memblk was not added. Though, the node id was
wrong too, a message is seen then in the logs:
kernel/numa.c: pr_info_once("Unknown target node for memory at 0x%llx, assuming node 0\n",
[1] commit fd49f99c1809 ("ACPI: NUMA: Add a node and memblk for each
CFMWS not in SRAT")
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/all/66271b0072317_69102944c@dwillia2-xfh.jf.intel.com.notmuch/
Fixes: 8f1004679987 ("ACPI/NUMA: Apply SRAT proximity domain to entire CFMWS window")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Robert Richter <rrichter@amd.com>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 72cc1980a0ef3ccad0d539e7dace63d0d7d432a4 ]
Commit 8238b4579866 ("wait_on_bit: add an acquire memory barrier") added
a new bitop, test_bit_acquire(), with proper wrapping in order to try to
optimize it at compile-time, but missed the list of bitops used for
checking their prototypes a bit below.
The functions added have consistent prototypes, so that no more changes
are required and no functional changes take place.
Fixes: 8238b4579866 ("wait_on_bit: add an acquire memory barrier")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 403ad17c06509794fdf6e4d4b3070bd5b56e2a8e ]
The ACPI IRQ mapping code supports parsing of ResourceSource,
but this is not reported thru _OSC.
Fix this by setting bit 13 ("Interrupt ResourceSource support")
when evaluating _OSC.
Fixes: d44fa3d46079 ("ACPI: Add support for ResourceSource/IRQ domain mapping")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d0d4f1474e36b195eaad477373127ae621334c01 ]
The ACPI spec says bit 17 should be used to indicate support
for Generic Initiator Affinity Structure in SRAT, but we currently
set bit 13 ("Interrupt ResourceSource support").
Fix this by actually setting bit 17 when evaluating _OSC.
Fixes: 01aabca2fd54 ("ACPI: Let ACPI know we support Generic Initiator Affinity Structures")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a8a967a243d71dd635ede076020f665a4df51c63 ]
A device driver for the Generic Event Device (ACPI0013) already
exists for quite some time, but support for it was never reported
thru _OSC.
Fix this by setting bit 11 ("Generic Event Device support") when
evaluating _OSC.
Fixes: 3db80c230da1 ("ACPI: implement Generic Event Device")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e8345f23ca37d6d41bb76be5d6a705ddf542817 ]
The code responsible for parsing the available p-states should
have no problems handling more than 16 p-states.
Indicate this by setting bit 10 ("Greater Than 16 p-state support")
when evaluating _OSC.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: a8a967a243d7 ("ACPI: bus: Indicate support for the Generic Event Device thru _OSC")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 95d43290f1e476b3be782dd17642e452d0436266 ]
The ACPI thermal driver already uses the _TPF ACPI method to retrieve
precise sampling time values, but this is not reported thru _OSC.
Fix this by setting bit 9 ("Fast Thermal Sampling support") when
evaluating _OSC.
Fixes: a2ee7581afd5 ("ACPI: thermal: Add Thermal fast Sampling Period (_TFP) support")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c121514df0daa800cc500dc2738e0b8a1c54af98 ]
If there was a possibility of an MLE basic STA profile without
subelements, we might reject it because we account for the one
octet for sta_info_len twice (it's part of itself, and in the
fixed portion). Like in ieee80211_mle_reconf_sta_prof_size_ok,
subtract 1 to adjust that.
When reading the elements we did take this into account, and
since there are always elements, this never really mattered.
Fixes: 7b6f08771bf6 ("wifi: ieee80211: Support validating ML station profile length")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.00bb0b20ed60.I8c41dd6fc14c4b187ab901dea15ade73c79fb98c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 74df22453c51392476117d7330bf02cee6e987cf ]
The __alloc_size annotation for kmemdup() was getting disabled under
KUnit testing because the replaced fortify_panic macro implementation
was using "return NULL" as a way to survive the sanity checking. But
having the chance to return NULL invalidated __alloc_size, so kmemdup
was not passing the __builtin_dynamic_object_size() tests any more:
[23:26:18] [PASSED] fortify_test_alloc_size_kmalloc_const
[23:26:19] # fortify_test_alloc_size_kmalloc_dynamic: EXPECTATION FAILED at lib/fortify_kunit.c:265
[23:26:19] Expected __builtin_dynamic_object_size(p, 1) == expected, but
[23:26:19] __builtin_dynamic_object_size(p, 1) == -1 (0xffffffffffffffff)
[23:26:19] expected == 11 (0xb)
[23:26:19] __alloc_size() not working with __bdos on kmemdup("hello there", len, gfp)
[23:26:19] [FAILED] fortify_test_alloc_size_kmalloc_dynamic
Normal builds were not affected: __alloc_size continued to work there.
Use a zero-sized allocation instead, which allows __alloc_size to
behave.
Fixes: 4ce615e798a7 ("fortify: Provide KUnit counters for failure testing")
Fixes: fa4a3f86d498 ("fortify: Add KUnit tests for runtime overflows")
Link: https://lore.kernel.org/r/20240501232937.work.532-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5a1a25be995e1014abd01600479915683e356f5c ]
I'm about to fix a tmpfs rename bug that requires the use of
internal simple_offset helpers that are not available in mm/shmem.c
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Link: https://lore.kernel.org/r/20240415152057.4605-3-cel@kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
Stable-dep-of: ad191eb6d694 ("shmem: Fix shmem_rename2()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 140ce28dd3bee8e53acc27f123ae474d69ef66f0 upstream.
Add a helper to check if partition scanning is enabled instead of
open coding the check in a few places. This now always checks for
the hidden flag even if all but one of the callers are never reachable
for hidden gendisks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240502130033.1958492-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 95feb3160eef0caa6018e175a5560b816aee8e79 upstream.
Due to an erratum with the SPR_DSA and SPR_IAX devices, it is not secure to assign
these devices to virtual machines. Add the PCI IDs of these devices to the VFIO
denylist to ensure that this is handled appropriately by the VFIO subsystem.
The SPR_DSA and SPR_IAX devices are on-SOC devices for the Sapphire Rapids
(and related) family of products that perform data movement and compression.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Add a new PCI ID which belongs to a new AMD CPU family 0x1a
- Ensure that that last level cache ID is set in all cases, in the AMD
CPU topology parsing code, in order to prevent invalid scheduling
domain CPU masks
* tag 'x86_urgent_for_v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/topology/amd: Ensure that LLC ID is initialized
x86/amd_nb: Add new PCI IDs for AMD family 0x1a
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM fixes from Andrew Morton:
"18 hotfixes, 7 of which are cc:stable.
More fixups for this cycle's page_owner updates. And a few userfaultfd
fixes. Otherwise, random singletons - see the individual changelogs
for details"
* tag 'mm-hotfixes-stable-2024-05-10-13-14' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mailmap: add entry for Barry Song
selftests/mm: fix powerpc ARCH check
mailmap: add entry for John Garry
XArray: set the marks correctly when splitting an entry
selftests/vDSO: fix runtime errors on LoongArch
selftests/vDSO: fix building errors on LoongArch
mm,page_owner: don't remove __GFP_NOLOCKDEP in add_stack_record_to_list
fs/proc/task_mmu: fix uffd-wp confusion in pagemap_scan_pmd_entry()
fs/proc/task_mmu: fix loss of young/dirty bits during pagemap scan
mm/vmalloc: fix return value of vb_alloc if size is 0
mm: use memalloc_nofs_save() in page_cache_ra_order()
kmsan: compiler_types: declare __no_sanitize_or_inline
lib/test_xarray.c: fix error assumptions on check_xa_multi_store_adv_add()
tools: fix userspace compilation with new test_xarray changes
MAINTAINERS: update URL's for KEYS/KEYRINGS_INTEGRITY and TPM DEVICE DRIVER
mm: page_owner: fix wrong information in dump_page_owner
maple_tree: fix mas_empty_area_rev() null pointer dereference
mm/userfaultfd: reset ptes when close() for wr-protected ones
|
|
Add the new PCI Device IDs to the MISC IDs list to support new
generation of AMD 1Ah family 70h Models of processors.
[ bp: Massage commit message. ]
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20240510111829.969501-1-Shyam-sundar.S-k@amd.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bluetooth and IPsec.
The bridge patch is actually a follow-up to a recent fix in the same
area. We have a pending v6.8 AF_UNIX regression; it should be solved
soon, but not in time for this PR.
Current release - regressions:
- eth: ks8851: Queue RX packets in IRQ handler instead of disabling
BHs
- net: bridge: fix corrupted ethernet header on multicast-to-unicast
Current release - new code bugs:
- xfrm: fix possible bad pointer derferencing in error path
Previous releases - regressionis:
- core: fix out-of-bounds access in ops_init
- ipv6:
- fix potential uninit-value access in __ip6_make_skb()
- fib6_rules: avoid possible NULL dereference in fib6_rule_action()
- tcp: use refcount_inc_not_zero() in tcp_twsk_unique().
- rtnetlink: correct nested IFLA_VF_VLAN_LIST attribute validation
- rxrpc: fix congestion control algorithm
- bluetooth:
- l2cap: fix slab-use-after-free in l2cap_connect()
- msft: fix slab-use-after-free in msft_do_close()
- eth: hns3: fix kernel crash when devlink reload during
initialization
- eth: dsa: mv88e6xxx: add phylink_get_caps for the mv88e6320/21
family
Previous releases - always broken:
- xfrm: preserve vlan tags for transport mode software GRO
- tcp: defer shutdown(SEND_SHUTDOWN) for TCP_SYN_RECV sockets
- eth: hns3: keep using user config after hardware reset"
* tag 'net-6.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
net: dsa: mv88e6xxx: read cmode on mv88e6320/21 serdes only ports
net: dsa: mv88e6xxx: add phylink_get_caps for the mv88e6320/21 family
net: hns3: fix kernel crash when devlink reload during initialization
net: hns3: fix port vlan filter not disabled issue
net: hns3: use appropriate barrier function after setting a bit value
net: hns3: release PTP resources if pf initialization failed
net: hns3: change type of numa_node_mask as nodemask_t
net: hns3: direct return when receive a unknown mailbox message
net: hns3: using user configure after hardware reset
net/smc: fix neighbour and rtable leak in smc_ib_find_route()
ipv6: prevent NULL dereference in ip6_output()
hsr: Simplify code for announcing HSR nodes timer setup
ipv6: fib6_rules: avoid possible NULL dereference in fib6_rule_action()
dt-bindings: net: mediatek: remove wrongly added clocks and SerDes
rxrpc: Only transmit one ACK per jumbo packet received
rxrpc: Fix congestion control algorithm
selftests: test_bridge_neigh_suppress.sh: Fix failures due to duplicate MAC
ipv6: Fix potential uninit-value access in __ip6_make_skb()
net: phy: marvell-88q2xxx: add support for Rev B1 and B2
appletalk: Improve handling of broadcast packets
...
|
|
This reverts commit 07ed11afb68d94eadd4ffc082b97c2331307c5ea.
Stephen Rostedt reports:
"I went to run my tests on my VMs and the tests hung on boot up.
Unfortunately, the most I ever got out was:
[ 93.607888] Testing event system initcall: OK
[ 93.667730] Running tests on all trace events:
[ 93.669757] Testing all events: OK
[ 95.631064] ------------[ cut here ]------------
Timed out after 60 seconds"
and further debugging points to a possible circular locking dependency
between the console_owner locking and the worker pool locking.
Reverting the commit allows Steve's VM to boot to completion again.
[ This may obviously result in the "[TTM] Buffer eviction failed"
messages again, which was the reason for that original revert. But at
this point this seems preferable to a non-booting system... ]
Reported-and-bisected-by: Steven Rostedt <rostedt@goodmis.org>
Link: https://lore.kernel.org/all/20240502081641.457aa25f@gandalf.local.home/
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Alex Constantino <dreaming.about.electric.sheep@gmail.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Timo Lindfors <timo.lindfors@iki.fi>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab fixes from Vlastimil Babka:
- Fix for cleanup infrastructure (Dan Carpenter)
This makes the __free(kfree) cleanup hooks not crash on error
pointers.
- SLUB fix for freepointer checking (Nicolas Bouchinet)
This fixes a recently introduced bug that manifests when
init_on_free, CONFIG_SLAB_FREELIST_HARDENED and consistency checks
(slub_debug=F) are all enabled, and results in false-positive
freepointer corrupt reports for caches that store freepointer outside
of the object area.
* tag 'slab-for-6.9-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
mm/slab: make __free(kfree) accept error pointers
mm/slub: avoid zeroing outside-object freepointer for single free
|
|
It turned out that KMSAN instruments READ_ONCE_NOCHECK(), resulting in
false positive reports, because __no_sanitize_or_inline enforced inlining.
Properly declare __no_sanitize_or_inline under __SANITIZE_MEMORY__, so
that it does not __always_inline the annotated function.
Link: https://lkml.kernel.org/r/20240426091622.3846771-1-glider@google.com
Fixes: 5de0ce85f5a4 ("kmsan: mark noinstr as __no_sanitize_memory")
Signed-off-by: Alexander Potapenko <glider@google.com>
Reported-by: syzbot+355c5bb8c1445c871ee8@syzkaller.appspotmail.com
Link: https://lkml.kernel.org/r/000000000000826ac1061675b0e3@google.com
Cc: <stable@vger.kernel.org>
Reviewed-by: Marco Elver <elver@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing and tracefs fixes from Steven Rostedt:
- Fix RCU callback of freeing an eventfs_inode.
The freeing of the eventfs_inode from the kref going to zero freed
the contents of the eventfs_inode and then used kfree_rcu() to free
the inode itself. But the contents should also be protected by RCU.
Switch to a call_rcu() that calls a function to free all of the
eventfs_inode after the RCU synchronization.
- The tracing subsystem maps its own descriptor to a file represented
by eventfs. The freeing of this descriptor needs to know when the
last reference of an eventfs_inode is released, but currently there
is no interface for that.
Add a "release" callback to the eventfs_inode entry array that allows
for freeing of data that can be referenced by the eventfs_inode being
opened. Then increment the ref counter for this descriptor when the
eventfs_inode file is created, and decrement/free it when the last
reference to the eventfs_inode is released and the file is removed.
This prevents races between freeing the descriptor and the opening of
the eventfs file.
- Fix the permission processing of eventfs.
The change to make the permissions of eventfs default to the mount
point but keep track of when changes were made had a side effect that
could cause security concerns. When the tracefs is remounted with a
given gid or uid, all the files within it should inherit that gid or
uid. But if the admin had changed the permission of some file within
the tracefs file system, it would not get updated by the remount.
This caused the kselftest of file permissions to fail the second time
it is run. The first time, all changes would look fine, but the
second time, because the changes were "saved", the remount did not
reset them.
Create a link list of all existing tracefs inodes, and clear the
saved flags on them on a remount if the remount changes the
corresponding gid or uid fields.
This also simplifies the code by removing the distinction between the
toplevel eventfs and an instance eventfs. They should both act the
same. They were different because of a misconception due to the
remount not resetting the flags. Now that remount resets all the
files and directories to default to the root node if a uid/gid is
specified, it makes the logic simpler to implement.
* tag 'trace-v6.9-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
eventfs: Have "events" directory get permissions from its parent
eventfs: Do not treat events directory different than other directories
eventfs: Do not differentiate the toplevel events directory
tracefs: Still use mount point as default permissions for instances
tracefs: Reset permissions on remount if permissions are options
eventfs: Free all of the eventfs_inode after RCU
eventfs/tracing: Add callback for release of an eventfs_inode
|
|
Synthetic events create and destroy tracefs files when they are created
and removed. The tracing subsystem has its own file descriptor
representing the state of the events attached to the tracefs files.
There's a race between the eventfs files and this file descriptor of the
tracing system where the following can cause an issue:
With two scripts 'A' and 'B' doing:
Script 'A':
echo "hello int aaa" > /sys/kernel/tracing/synthetic_events
while :
do
echo 0 > /sys/kernel/tracing/events/synthetic/hello/enable
done
Script 'B':
echo > /sys/kernel/tracing/synthetic_events
Script 'A' creates a synthetic event "hello" and then just writes zero
into its enable file.
Script 'B' removes all synthetic events (including the newly created
"hello" event).
What happens is that the opening of the "enable" file has:
{
struct trace_event_file *file = inode->i_private;
int ret;
ret = tracing_check_open_get_tr(file->tr);
[..]
But deleting the events frees the "file" descriptor, and a "use after
free" happens with the dereference at "file->tr".
The file descriptor does have a reference counter, but there needs to be a
way to decrement it from the eventfs when the eventfs_inode is removed
that represents this file descriptor.
Add an optional "release" callback to the eventfs_entry array structure,
that gets called when the eventfs file is about to be removed. This allows
for the creating on the eventfs file to increment the tracing file
descriptor ref counter. When the eventfs file is deleted, it can call the
release function that will call the put function for the tracing file
descriptor.
This will protect the tracing file from being freed while a eventfs file
that references it is being opened.
Link: https://lore.kernel.org/linux-trace-kernel/20240426073410.17154-1-Tze-nan.Wu@mediatek.com/
Link: https://lore.kernel.org/linux-trace-kernel/20240502090315.448cba46@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Fixes: 5790b1fb3d672 ("eventfs: Remove eventfs_file and just use eventfs_inode")
Reported-by: Tze-nan wu <Tze-nan.Wu@mediatek.com>
Tested-by: Tze-nan Wu (吳澤南) <Tze-nan.Wu@mediatek.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2024-05-02
1) Fix an error pointer dereference in xfrm_in_fwd_icmp.
From Antony Antony.
2) Preserve vlan tags for ESP transport mode software GRO.
From Paul Davey.
3) Fix a spelling mistake in an uapi xfrm.h comment.
From Anotny Antony.
* tag 'ipsec-2024-05-02' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
xfrm: Correct spelling mistake in xfrm.h comment
xfrm: Preserve vlan tags for transport mode software GRO
xfrm: fix possible derferencing in error path
====================
Link: https://lore.kernel.org/r/20240502084838.2269355-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"As usual in a late stage, we received a fair amount of fixes for ASoC,
and it became bigger than wished. But all fixes are rather device-
specific, and they look pretty safe to apply.
A major par of changes are series of fixes for ASoC meson and SOF
drivers as well as for Realtek and Cirrus codecs. In addition, recent
emu10k1 regression fixes and usual HD-audio quirks are included"
* tag 'sound-6.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (46 commits)
ALSA: hda/realtek: Fix build error without CONFIG_PM
ALSA: hda/realtek: Fix conflicting PCI SSID 17aa:386f for Lenovo Legion models
ALSA: hda/realtek - Set GPIO3 to default at S4 state for Thinkpad with ALC1318
ALSA: hda: intel-sdw-acpi: fix usage of device_get_named_child_node()
ALSA: hda: intel-dsp-config: harden I2C/I2S codec detection
ASoC: cs35l56: fix usages of device_get_named_child_node()
ASoC: da7219-aad: fix usage of device_get_named_child_node()
ASoC: meson: cards: select SND_DYNAMIC_MINORS
ASoC: meson: axg-tdm: add continuous clock support
ASoC: meson: axg-tdm-interface: manage formatters in trigger
ASoC: meson: axg-card: make links nonatomic
ASoC: meson: axg-fifo: use threaded irq to check periods
ALSA: hda/realtek: Fix mute led of HP Laptop 15-da3001TU
ALSA: emu10k1: make E-MU FPGA writes potentially more reliable
ALSA: emu10k1: fix E-MU dock initialization
ALSA: emu10k1: use mutex for E-MU FPGA access locking
ALSA: emu10k1: move the whole GPIO event handling to the workqueue
ALSA: emu10k1: factor out snd_emu1010_load_dock_firmware()
ALSA: emu10k1: fix E-MU card dock presence monitoring
ASoC: rt715-sdca: volume step modification
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf.
Relatively calm week, likely due to public holiday in most places. No
known outstanding regressions.
Current release - regressions:
- rxrpc: fix wrong alignmask in __page_frag_alloc_align()
- eth: e1000e: change usleep_range to udelay in PHY mdic access
Previous releases - regressions:
- gro: fix udp bad offset in socket lookup
- bpf: fix incorrect runtime stat for arm64
- tipc: fix UAF in error path
- netfs: fix a potential infinite loop in extract_user_to_sg()
- eth: ice: ensure the copied buf is NUL terminated
- eth: qeth: fix kernel panic after setting hsuid
Previous releases - always broken:
- bpf:
- verifier: prevent userspace memory access
- xdp: use flags field to disambiguate broadcast redirect
- bridge: fix multicast-to-unicast with fraglist GSO
- mptcp: ensure snd_nxt is properly initialized on connect
- nsh: fix outer header access in nsh_gso_segment().
- eth: bcmgenet: fix racing registers access
- eth: vxlan: fix stats counters.
Misc:
- a bunch of MAINTAINERS file updates"
* tag 'net-6.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (45 commits)
MAINTAINERS: mark MYRICOM MYRI-10G as Orphan
MAINTAINERS: remove Ariel Elior
net: gro: add flush check in udp_gro_receive_segment
net: gro: fix udp bad offset in socket lookup by adding {inner_}network_offset to napi_gro_cb
ipv4: Fix uninit-value access in __ip_make_skb()
s390/qeth: Fix kernel panic after setting hsuid
vxlan: Pull inner IP header in vxlan_rcv().
tipc: fix a possible memleak in tipc_buf_append
tipc: fix UAF in error path
rxrpc: Clients must accept conn from any address
net: core: reject skb_copy(_expand) for fraglist GSO skbs
net: bridge: fix multicast-to-unicast with fraglist GSO
mptcp: ensure snd_nxt is properly initialized on connect
e1000e: change usleep_range to udelay in PHY mdic access
net: dsa: mv88e6xxx: Fix number of databases for 88E6141 / 88E6341
cxgb4: Properly lock TX queue for the selftest.
rxrpc: Fix using alignmask being zero for __page_frag_alloc_align()
vxlan: Add missing VNI filter counter update in arp_reduce().
vxlan: Fix racy device stats updates.
net: qede: use return from qede_parse_actions()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"There's a few simple driver specific fixes here, plus some core
cleanups from Matti which fix issues found with client drivers due to
the API being confusing.
The two fixes for the stubs provide more constructive behaviour with
!REGULATOR configurations, issues were noticed with some hwmon drivers
which would otherwise have needed confusing bodges in the users.
The irq_helpers fix to duplicate the provided name for the interrupt
controller was found because a driver got this wrong and it's again a
case where the core is the sensible place to put the fix"
* tag 'regulator-fix-v6.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: change devm_regulator_get_enable_optional() stub to return Ok
regulator: change stubbed devm_regulator_get_enable to return Ok
regulator: vqmmc-ipq4019: fix module autoloading
regulator: qcom-refgen: fix module autoloading
regulator: mt6360: De-capitalize devicetree regulator subnodes
regulator: irq_helpers: duplicate IRQ name
|
|
Currently, if an automatically freed allocation is an error pointer that
will lead to a crash. An example of this is in wm831x_gpio_dbg_show().
171 char *label __free(kfree) = gpiochip_dup_line_label(chip, i);
172 if (IS_ERR(label)) {
173 dev_err(wm831x->dev, "Failed to duplicate label\n");
174 continue;
175 }
The auto clean up function should check for error pointers as well,
otherwise we're going to keep hitting issues like this.
Fixes: 54da6a092431 ("locking: Introduce __cleanup() based infrastructure")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- Make the CPU_MITIGATIONS=n interaction with conflicting
mitigation-enabling boot parameters a bit saner.
- Re-enable CPU mitigations by default on non-x86
- Fix TDX shared bit propagation on mprotect()
- Fix potential show_regs() system hang when PKE initialization
is not fully finished yet.
- Add the 0x10-0x1f model IDs to the Zen5 range
- Harden #VC instruction emulation some more
* tag 'x86-urgent-2024-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu: Ignore "mitigations" kernel parameter if CPU_MITIGATIONS=n
cpu: Re-enable CPU mitigations by default for !X86 architectures
x86/tdx: Preserve shared bit on mprotect()
x86/cpu: Fix check for RDPKRU in __show_regs()
x86/CPU/AMD: Add models 0x10-0x1f to the Zen5 range
x86/sev: Check for MWAITX and MONITORX opcodes in the #VC handler
|
|
create_prof_cpu_mask() is no longer used after commit 1f44a225777e ("s390:
convert interrupt handling to use generic hardirq").
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2024-04-26
We've added 12 non-merge commits during the last 22 day(s) which contain
a total of 14 files changed, 168 insertions(+), 72 deletions(-).
The main changes are:
1) Fix BPF_PROBE_MEM in verifier and JIT to skip loads from vsyscall page,
from Puranjay Mohan.
2) Fix a crash in XDP with devmap broadcast redirect when the latter map
is in process of being torn down, from Toke Høiland-Jørgensen.
3) Fix arm64 and riscv64 BPF JITs to properly clear start time for BPF
program runtime stats, from Xu Kuohai.
4) Fix a sockmap KCSAN-reported data race in sk_psock_skb_ingress_enqueue,
from Jason Xing.
5) Fix BPF verifier error message in resolve_pseudo_ldimm64,
from Anton Protopopov.
6) Fix missing DEBUG_INFO_BTF_MODULES Kconfig menu item,
from Andrii Nakryiko.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: Test PROBE_MEM of VSYSCALL_ADDR on x86-64
bpf, x86: Fix PROBE_MEM runtime load check
bpf: verifier: prevent userspace memory access
xdp: use flags field to disambiguate broadcast redirect
arm32, bpf: Reimplement sign-extension mov instruction
riscv, bpf: Fix incorrect runtime stats
bpf, arm64: Fix incorrect runtime stats
bpf: Fix a verifier verbose message
bpf, skmsg: Fix NULL pointer dereference in sk_psock_skb_ingress_enqueue
MAINTAINERS: bpf: Add Lehui and Puranjay as riscv64 reviewers
MAINTAINERS: Update email address for Puranjay Mohan
bpf, kconfig: Fix DEBUG_INFO_BTF_MODULES Kconfig definition
====================
Link: https://lore.kernel.org/r/20240426224248.26197-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are a lot of minor DT fixes for Mediatek, Rockchip, Qualcomm and
Microchip and NXP, addressing both build-time warnings and bugs found
during runtime testing.
Most of these changes are machine specific fixups, but there are a few
notable regressions that affect an entire SoC:
- The Qualcomm MSI support that was improved for 6.9 ended up being
wrong on some chips and now gets fixed.
- The i.MX8MP camera interface broke due to a typo and gets updated
again.
The main driver fix is also for Qualcomm platforms, rewriting an
interface in the QSEECOM firmware support that could lead to crashing
the kernel from a trusted application.
The only other code changes are minor fixes for Mediatek SoC drivers"
* tag 'soc-fixes-6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (50 commits)
ARM: dts: imx6ull-tarragon: fix USB over-current polarity
soc: mediatek: mtk-socinfo: depends on CONFIG_SOC_BUS
soc: mediatek: mtk-svs: Append "-thermal" to thermal zone names
arm64: dts: imx8mp: Fix assigned-clocks for second CSI2
ARM: dts: microchip: at91-sama7g54_curiosity: Replace regulator-suspend-voltage with the valid property
ARM: dts: microchip: at91-sama7g5ek: Replace regulator-suspend-voltage with the valid property
arm64: dts: rockchip: Fix USB interface compatible string on kobol-helios64
arm64: dts: qcom: sc8180x: Fix ss_phy_irq for secondary USB controller
arm64: dts: qcom: sm8650: Fix the msi-map entries
arm64: dts: qcom: sm8550: Fix the msi-map entries
arm64: dts: qcom: sm8450: Fix the msi-map entries
arm64: dts: qcom: sc8280xp: add missing PCIe minimum OPP
arm64: dts: qcom: x1e80100: Fix the compatible for cluster idle states
arm64: dts: qcom: Fix type of "wdog" IRQs for remoteprocs
arm64: dts: rockchip: regulator for sd needs to be always on for BPI-R2Pro
dt-bindings: rockchip: grf: Add missing type to 'pcie-phy' node
arm64: dts: rockchip: drop redundant disable-gpios in Lubancat 2
arm64: dts: rockchip: drop redundant disable-gpios in Lubancat 1
arm64: dts: rockchip: drop redundant pcie-reset-suspend in Scarlet Dumo
arm64: dts: rockchip: mark system power controller and fix typo on orangepi-5-plus
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"11 hotfixes. 8 are cc:stable and the remaining 3 (nice ratio!) address
post-6.8 issues or aren't considered suitable for backporting.
All except one of these are for MM. I see no particular theme - it's
singletons all over"
* tag 'mm-hotfixes-stable-2024-04-26-13-30' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/hugetlb: fix DEBUG_LOCKS_WARN_ON(1) when dissolve_free_hugetlb_folio()
selftests: mm: protection_keys: save/restore nr_hugepages value from launch script
stackdepot: respect __GFP_NOLOCKDEP allocation flag
hugetlb: check for anon_vma prior to folio allocation
mm: zswap: fix shrinker NULL crash with cgroup_disable=memory
mm: turn folio_test_hugetlb into a PageType
mm: support page_mapcount() on page_has_type() pages
mm: create FOLIO_FLAG_FALSE and FOLIO_TYPE_OPS macros
mm/hugetlb: fix missing hugetlb_lock for resv uncharge
selftests: mm: fix unused and uninitialized variable warning
selftests/harness: remove use of LINE_MAX
|
|
With BPF_PROBE_MEM, BPF allows de-referencing an untrusted pointer. To
thwart invalid memory accesses, the JITs add an exception table entry
for all such accesses. But in case the src_reg + offset is a userspace
address, the BPF program might read that memory if the user has
mapped it.
Make the verifier add guard instructions around such memory accesses and
skip the load if the address falls into the userspace region.
The JITs need to implement bpf_arch_uaddress_limit() to define where
the userspace addresses end for that architecture or TASK_SIZE is taken
as default.
The implementation is as follows:
REG_AX = SRC_REG
if(offset)
REG_AX += offset;
REG_AX >>= 32;
if (REG_AX <= (uaddress_limit >> 32))
DST_REG = 0;
else
DST_REG = *(size *)(SRC_REG + offset);
Comparing just the upper 32 bits of the load address with the upper
32 bits of uaddress_limit implies that the values are being aligned down
to a 4GB boundary before comparison.
The above means that all loads with address <= uaddress_limit + 4GB are
skipped. This is acceptable because there is a large hole (much larger
than 4GB) between userspace and kernel space memory, therefore a
correctly functioning BPF program should not access this 4GB memory
above the userspace.
Let's analyze what this patch does to the following fentry program
dereferencing an untrusted pointer:
SEC("fentry/tcp_v4_connect")
int BPF_PROG(fentry_tcp_v4_connect, struct sock *sk)
{
*(volatile long *)sk;
return 0;
}
BPF Program before | BPF Program after
------------------ | -----------------
0: (79) r1 = *(u64 *)(r1 +0) 0: (79) r1 = *(u64 *)(r1 +0)
-----------------------------------------------------------------------
1: (79) r1 = *(u64 *)(r1 +0) --\ 1: (bf) r11 = r1
----------------------------\ \ 2: (77) r11 >>= 32
2: (b7) r0 = 0 \ \ 3: (b5) if r11 <= 0x8000 goto pc+2
3: (95) exit \ \-> 4: (79) r1 = *(u64 *)(r1 +0)
\ 5: (05) goto pc+1
\ 6: (b7) r1 = 0
\--------------------------------------
7: (b7) r0 = 0
8: (95) exit
As you can see from above, in the best case (off=0), 5 extra instructions
are emitted.
Now, we analyze the same program after it has gone through the JITs of
ARM64 and RISC-V architectures. We follow the single load instruction
that has the untrusted pointer and see what instrumentation has been
added around it.
x86-64 JIT
==========
JIT's Instrumentation
(upstream)
---------------------
0: nopl 0x0(%rax,%rax,1)
5: xchg %ax,%ax
7: push %rbp
8: mov %rsp,%rbp
b: mov 0x0(%rdi),%rdi
---------------------------------
f: movabs $0x800000000000,%r11
19: cmp %r11,%rdi
1c: jb 0x000000000000002a
1e: mov %rdi,%r11
21: add $0x0,%r11
28: jae 0x000000000000002e
2a: xor %edi,%edi
2c: jmp 0x0000000000000032
2e: mov 0x0(%rdi),%rdi
---------------------------------
32: xor %eax,%eax
34: leave
35: ret
The x86-64 JIT already emits some instructions to protect against user
memory access. This patch doesn't make any changes for the x86-64 JIT.
ARM64 JIT
=========
No Intrumentation Verifier's Instrumentation
(upstream) (This patch)
----------------- --------------------------
0: add x9, x30, #0x0 0: add x9, x30, #0x0
4: nop 4: nop
8: paciasp 8: paciasp
c: stp x29, x30, [sp, #-16]! c: stp x29, x30, [sp, #-16]!
10: mov x29, sp 10: mov x29, sp
14: stp x19, x20, [sp, #-16]! 14: stp x19, x20, [sp, #-16]!
18: stp x21, x22, [sp, #-16]! 18: stp x21, x22, [sp, #-16]!
1c: stp x25, x26, [sp, #-16]! 1c: stp x25, x26, [sp, #-16]!
20: stp x27, x28, [sp, #-16]! 20: stp x27, x28, [sp, #-16]!
24: mov x25, sp 24: mov x25, sp
28: mov x26, #0x0 28: mov x26, #0x0
2c: sub x27, x25, #0x0 2c: sub x27, x25, #0x0
30: sub sp, sp, #0x0 30: sub sp, sp, #0x0
34: ldr x0, [x0] 34: ldr x0, [x0]
--------------------------------------------------------------------------------
38: ldr x0, [x0] ----------\ 38: add x9, x0, #0x0
-----------------------------------\\ 3c: lsr x9, x9, #32
3c: mov x7, #0x0 \\ 40: cmp x9, #0x10, lsl #12
40: mov sp, sp \\ 44: b.ls 0x0000000000000050
44: ldp x27, x28, [sp], #16 \\--> 48: ldr x0, [x0]
48: ldp x25, x26, [sp], #16 \ 4c: b 0x0000000000000054
4c: ldp x21, x22, [sp], #16 \ 50: mov x0, #0x0
50: ldp x19, x20, [sp], #16 \---------------------------------------
54: ldp x29, x30, [sp], #16 54: mov x7, #0x0
58: add x0, x7, #0x0 58: mov sp, sp
5c: autiasp 5c: ldp x27, x28, [sp], #16
60: ret 60: ldp x25, x26, [sp], #16
64: nop 64: ldp x21, x22, [sp], #16
68: ldr x10, 0x0000000000000070 68: ldp x19, x20, [sp], #16
6c: br x10 6c: ldp x29, x30, [sp], #16
70: add x0, x7, #0x0
74: autiasp
78: ret
7c: nop
80: ldr x10, 0x0000000000000088
84: br x10
There are 6 extra instructions added in ARM64 in the best case. This will
become 7 in the worst case (off != 0).
RISC-V JIT (RISCV_ISA_C Disabled)
==========
No Intrumentation Verifier's Instrumentation
(upstream) (This patch)
----------------- --------------------------
0: nop 0: nop
4: nop 4: nop
8: li a6, 33 8: li a6, 33
c: addi sp, sp, -16 c: addi sp, sp, -16
10: sd s0, 8(sp) 10: sd s0, 8(sp)
14: addi s0, sp, 16 14: addi s0, sp, 16
18: ld a0, 0(a0) 18: ld a0, 0(a0)
---------------------------------------------------------------
1c: ld a0, 0(a0) --\ 1c: mv t0, a0
--------------------------\ \ 20: srli t0, t0, 32
20: li a5, 0 \ \ 24: lui t1, 4096
24: ld s0, 8(sp) \ \ 28: sext.w t1, t1
28: addi sp, sp, 16 \ \ 2c: bgeu t1, t0, 12
2c: sext.w a0, a5 \ \--> 30: ld a0, 0(a0)
30: ret \ 34: j 8
\ 38: li a0, 0
\------------------------------
3c: li a5, 0
40: ld s0, 8(sp)
44: addi sp, sp, 16
48: sext.w a0, a5
4c: ret
There are 7 extra instructions added in RISC-V.
Fixes: 800834285361 ("bpf, arm64: Add BPF exception tables")
Reported-by: Breno Leitao <leitao@debian.org>
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Link: https://lore.kernel.org/r/20240424100210.11982-2-puranjay@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into for-next
Qualcomm driver fix for v6.9
This reworks the memory layout of the argument buffers passed to trusted
applications in QSEECOM, to avoid failures and system crashes.
* tag 'qcom-drivers-fixes-for-6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
firmware: qcom: uefisecapp: Fix memory related IO errors and crashes
Link: https://lore.kernel.org/r/20240420163816.1133528-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The software GRO path for esp transport mode uses skb_mac_header_rebuild
prior to re-injecting the packet via the xfrm_napi_dev. This only
copies skb->mac_len bytes of header which may not be sufficient if the
packet contains 802.1Q tags or other VLAN tags. Worse copying only the
initial header will leave a packet marked as being VLAN tagged but
without the corresponding tag leading to mangling when it is later
untagged.
The VLAN tags are important when receiving the decrypted esp transport
mode packet after GRO processing to ensure it is received on the correct
interface.
Therefore record the full mac header length in xfrm*_transport_input for
later use in corresponding xfrm*_transport_finish to copy the entire mac
header when rebuilding the mac header for GRO. The skb->data pointer is
left pointing skb->mac_header bytes after the start of the mac header as
is expected by the network stack and network and transport header
offsets reset to this location.
Fixes: 7785bba299a8 ("esp: Add a software GRO codepath")
Signed-off-by: Paul Davey <paul.davey@alliedtelesis.co.nz>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, wireless and bluetooth.
Nothing major, regression fixes are mostly in drivers, two more of
those are flowing towards us thru various trees. I wish some of the
changes went into -rc5, we'll try to keep an eye on frequency of PRs
from sub-trees.
Also disproportional number of fixes for bugs added in v6.4, strange
coincidence.
Current release - regressions:
- igc: fix LED-related deadlock on driver unbind
- wifi: mac80211: small fixes to recent clean up of the connection
process
- Revert "wifi: iwlwifi: bump FW API to 90 for BZ/SC devices", kernel
doesn't have all the code to deal with that version, yet
- Bluetooth:
- set power_ctrl_enabled on NULL returned by gpiod_get_optional()
- qca: fix invalid device address check, again
- eth: ravb: fix registered interrupt names
Current release - new code bugs:
- wifi: mac80211: check EHT/TTLM action frame length
Previous releases - regressions:
- fix sk_memory_allocated_{add|sub} for architectures where
__this_cpu_{add|sub}* are not IRQ-safe
- dsa: mv88e6xx: fix link setup for 88E6250
Previous releases - always broken:
- ip: validate dev returned from __in_dev_get_rcu(), prevent possible
null-derefs in a few places
- switch number of for_each_rcu() loops using call_rcu() on the
iterator to for_each_safe()
- macsec: fix isolation of broadcast traffic in presence of offload
- vxlan: drop packets from invalid source address
- eth: mlxsw: trap and ACL programming fixes
- eth: bnxt: PCIe error recovery fixes, fix counting dropped packets
- Bluetooth:
- lots of fixes for the command submission rework from v6.4
- qca: fix NULL-deref on non-serdev suspend
Misc:
- tools: ynl: don't ignore errors in NLMSG_DONE messages"
* tag 'net-6.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (88 commits)
af_unix: Suppress false-positive lockdep splat for spin_lock() in __unix_gc().
net: b44: set pause params only when interface is up
tls: fix lockless read of strp->msg_ready in ->poll
dpll: fix dpll_pin_on_pin_register() for multiple parent pins
net: ravb: Fix registered interrupt names
octeontx2-af: fix the double free in rvu_npc_freemem()
net: ethernet: ti: am65-cpts: Fix PTPv1 message type on TX packets
ice: fix LAG and VF lock dependency in ice_reset_vf()
iavf: Fix TC config comparison with existing adapter TC config
i40e: Report MFS in decimal base instead of hex
i40e: Do not use WQ_MEM_RECLAIM flag for workqueue
net: ti: icssg-prueth: Fix signedness bug in prueth_init_rx_chns()
net/mlx5e: Advertise mlx5 ethernet driver updates sk_buff md_dst for MACsec
macsec: Detect if Rx skb is macsec-related for offloading devices that update md_dst
ethernet: Add helper for assigning packet type when dest address does not match device address
macsec: Enable devices to advertise whether they update sk_buff md_dst during offloads
net: phy: dp83869: Fix MII mode failure
netfilter: nf_tables: honor table dormant flag from netdev release event path
eth: bnxt: fix counting packets discarded due to OOM and netpoll
igc: Fix LED-related deadlock on driver unbind
...
|