| Age | Commit message (Collapse) | Author |
|---|
|
commit 2f8dea1692eef2b7ba6a256246ed82c365fdc686 upstream.
Consider a scenario where a CPU transitions from CPUHP_ONLINE to halfway
through a CPU hotunplug down to CPUHP_HRTIMERS_PREPARE, and then back to
CPUHP_ONLINE:
Since hrtimers_prepare_cpu() does not run, cpu_base.hres_active remains set
to 1 throughout. However, during a CPU unplug operation, the tick and the
clockevents are shut down at CPUHP_AP_TICK_DYING. On return to the online
state, for instance CFS incorrectly assumes that the hrtick is already
active, and the chance of the clockevent device to transition to oneshot
mode is also lost forever for the CPU, unless it goes back to a lower state
than CPUHP_HRTIMERS_PREPARE once.
This round-trip reveals another issue; cpu_base.online is not set to 1
after the transition, which appears as a WARN_ON_ONCE in enqueue_hrtimer().
Aside of that, the bulk of the per CPU state is not reset either, which
means there are dangling pointers in the worst case.
Address this by adding a corresponding startup() callback, which resets the
stale per CPU state and sets the online flag.
[ tglx: Make the new callback unconditionally available, remove the online
modification in the prepare() callback and clear the remaining
state in the starting callback instead of the prepare callback ]
Fixes: 5c0930ccaad5 ("hrtimers: Push pending hrtimers away from outgoing CPU earlier")
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20241220134421.3809834-1-koichiro.den@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
.poll()
[ Upstream commit cacd9ae4bf801ff4125d8961bb9a3ba955e51680 ]
As the comment above waitqueue_active() explains, it can only be used
if both waker and waiter have mb()'s that pair with each other. However
__pollwait() is broken in this respect.
This is not pipe-specific, but let's look at pipe_poll() for example:
poll_wait(...); // -> __pollwait() -> add_wait_queue()
LOAD(pipe->head);
LOAD(pipe->head);
In theory these LOAD()'s can leak into the critical section inside
add_wait_queue() and can happen before list_add(entry, wq_head), in this
case pipe_poll() can race with wakeup_pipe_readers/writers which do
smp_mb();
if (waitqueue_active(wq_head))
wake_up_interruptible(wq_head);
There are more __pollwait()-like functions (grep init_poll_funcptr), and
it seems that at least ep_ptable_queue_proc() has the same problem, so the
patch adds smp_mb() into poll_wait().
Link: https://lore.kernel.org/all/20250102163320.GA17691@redhat.com/
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lore.kernel.org/r/20250107162717.GA18922@redhat.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fd4f101edbd9f99567ab2adb1f2169579ede7c13 ]
Many (struct pernet_operations)->exit_batch() methods have
to acquire rtnl.
In presence of rtnl mutex pressure, this makes cleanup_net()
very slow.
This patch adds a new exit_batch_rtnl() method to reduce
number of rtnl acquisitions from cleanup_net().
exit_batch_rtnl() handlers are called while rtnl is locked,
and devices to be killed can be queued in a list provided
as their second argument.
A single unregister_netdevice_many() is called right
before rtnl is released.
exit_batch_rtnl() handlers are called before ->exit() and
->exit_batch() handlers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 46841c7053e6 ("gtp: Use for_each_netdev_rcu() in gtp_genl_dump_pdp().")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 130eac4170859fb368681e00d390f20f44bbf27b upstream.
A recent patch caused an unused-function warning in builds with
CONFIG_PM disabled, after the function became marked 'static':
drivers/usb/host/xhci-pci.c:91:13: error: 'xhci_msix_sync_irqs' defined but not used [-Werror=unused-function]
91 | static void xhci_msix_sync_irqs(struct xhci_hcd *xhci)
| ^~~~~~~~~~~~~~~~~~~
This could be solved by adding another #ifdef, but as there is
a trend towards removing CONFIG_PM checks in favor of helper
macros, do the same conversion here and use pm_ptr() to get
either a function pointer or NULL but avoid the warning.
As the hidden functions reference some other symbols, make
sure those are visible at compile time, at the minimal cost of
a few extra bytes for 'struct usb_device'.
Fixes: 9abe15d55dcc ("xhci: Move xhci MSI sync function to to xhci-pci")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230328131114.1296430-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6fad274f06f038c29660aa53fbad14241c9fd976 upstream.
Add a MEM_WRITE attribute for BPF helper functions which can be used in
bpf_func_proto to annotate an argument type in order to let the verifier
know that the helper writes into the memory passed as an argument. In
the past MEM_UNINIT has been (ab)used for this function, but the latter
merely tells the verifier that the passed memory can be uninitialized.
There have been bugs with overloading the latter but aside from that
there are also cases where the passed memory is read + written which
currently cannot be expressed, see also 4b3786a6c539 ("bpf: Zero former
ARG_PTR_TO_{LONG,INT} args in case of error").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20241021152809.33343-1-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: BRUNO VERNAY <bruno.vernay@se.com>
Signed-off-by: Hugo SIMELIERE <hsimeliere.opensource@witekio.com>
Stable-dep-of: 8ea607330a39 ("bpf: Fix overloading of MEM_UNINIT's meaning")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3479c7549fb1dfa7a1db4efb7347c7b8ef50de4b ]
If the backlog of listen() is set to zero, sk_acceptq_is_full() allows
one connection to be made, but inet_csk_reqsk_queue_is_full() does not.
When the net.ipv4.tcp_syncookies is zero, inet_csk_reqsk_queue_is_full()
will cause an immediate drop before the sk_acceptq_is_full() check in
tcp_conn_request(), resulting in no connection can be made.
This patch tries to keep consistent with 64a146513f8f ("[NET]: Revert
incorrect accept queue backlog changes.").
Link: https://lore.kernel.org/netdev/20250102080258.53858-1-kuniyu@amazon.com/
Fixes: ef547f2ac16b ("tcp: remove max_qlen_log")
Signed-off-by: Zhongqiu Duan <dzq.aishenghu0@gmail.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250102171426.915276-1-dzq.aishenghu0@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9a79c65f00e2b036e17af3a3a607d7d732b7affb ]
Since commit 099ecf59f05b ("net: annotate lockless accesses to
sk->sk_max_ack_backlog") decided to handle the sk_max_ack_backlog
locklessly, there is one more function mostly called in TCP/DCCP
cases. So this patch completes it:)
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240331090521.71965-1-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 3479c7549fb1 ("tcp/dccp: allow a connection when sk_max_ack_backlog is zero")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit fd7b4f9f46d46acbc7af3a439bb0d869efdc5c58 upstream.
When CONFIG_KASAN_SW_TAGS and CONFIG_KASAN_STACK are enabled, the
object_is_on_stack() function may produce incorrect results due to the
presence of tags in the obj pointer, while the stack pointer does not have
tags. This discrepancy can lead to incorrect stack object detection and
subsequently trigger warnings if CONFIG_DEBUG_OBJECTS is also enabled.
Example of the warning:
ODEBUG: object 3eff800082ea7bb0 is NOT on stack ffff800082ea0000, but annotated.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at lib/debugobjects.c:557 __debug_object_init+0x330/0x364
Modules linked in:
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.0-rc5 #4
Hardware name: linux,dummy-virt (DT)
pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __debug_object_init+0x330/0x364
lr : __debug_object_init+0x330/0x364
sp : ffff800082ea7b40
x29: ffff800082ea7b40 x28: 98ff0000c0164518 x27: 98ff0000c0164534
x26: ffff800082d93ec8 x25: 0000000000000001 x24: 1cff0000c00172a0
x23: 0000000000000000 x22: ffff800082d93ed0 x21: ffff800081a24418
x20: 3eff800082ea7bb0 x19: efff800000000000 x18: 0000000000000000
x17: 00000000000000ff x16: 0000000000000047 x15: 206b63617473206e
x14: 0000000000000018 x13: ffff800082ea7780 x12: 0ffff800082ea78e
x11: 0ffff800082ea790 x10: 0ffff800082ea79d x9 : 34d77febe173e800
x8 : 34d77febe173e800 x7 : 0000000000000001 x6 : 0000000000000001
x5 : feff800082ea74b8 x4 : ffff800082870a90 x3 : ffff80008018d3c4
x2 : 0000000000000001 x1 : ffff800082858810 x0 : 0000000000000050
Call trace:
__debug_object_init+0x330/0x364
debug_object_init_on_stack+0x30/0x3c
schedule_hrtimeout_range_clock+0xac/0x26c
schedule_hrtimeout+0x1c/0x30
wait_task_inactive+0x1d4/0x25c
kthread_bind_mask+0x28/0x98
init_rescuer+0x1e8/0x280
workqueue_init+0x1a0/0x3cc
kernel_init_freeable+0x118/0x200
kernel_init+0x28/0x1f0
ret_from_fork+0x10/0x20
---[ end trace 0000000000000000 ]---
ODEBUG: object 3eff800082ea7bb0 is NOT on stack ffff800082ea0000, but annotated.
------------[ cut here ]------------
Link: https://lkml.kernel.org/r/20241113042544.19095-1-qun-wei.lin@mediatek.com
Signed-off-by: Qun-Wei Lin <qun-wei.lin@mediatek.com>
Cc: Andrew Yang <andrew.yang@mediatek.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Casper Li <casper.li@mediatek.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Pasha Tatashin <pasha.tatashin@soleen.com>
Cc: Shakeel Butt <shakeel.butt@linux.dev>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alva Lan <alvalan9@foxmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4d94f05558271654670d18c26c912da0c1c15549 ]
This reworks hci_cb_list to not use mutex hci_cb_list_lock to avoid bugs
like the bellow:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:585
in_atomic(): 0, irqs_disabled(): 0, non_block: 0, pid: 5070, name: kworker/u9:2
preempt_count: 0, expected: 0
RCU nest depth: 1, expected: 0
4 locks held by kworker/u9:2/5070:
#0: ffff888015be3948 ((wq_completion)hci0#2){+.+.}-{0:0}, at: process_one_work kernel/workqueue.c:3229 [inline]
#0: ffff888015be3948 ((wq_completion)hci0#2){+.+.}-{0:0}, at: process_scheduled_works+0x8e0/0x1770 kernel/workqueue.c:3335
#1: ffffc90003b6fd00 ((work_completion)(&hdev->rx_work)){+.+.}-{0:0}, at: process_one_work kernel/workqueue.c:3230 [inline]
#1: ffffc90003b6fd00 ((work_completion)(&hdev->rx_work)){+.+.}-{0:0}, at: process_scheduled_works+0x91b/0x1770 kernel/workqueue.c:3335
#2: ffff8880665d0078 (&hdev->lock){+.+.}-{3:3}, at: hci_le_create_big_complete_evt+0xcf/0xae0 net/bluetooth/hci_event.c:6914
#3: ffffffff8e132020 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:298 [inline]
#3: ffffffff8e132020 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:750 [inline]
#3: ffffffff8e132020 (rcu_read_lock){....}-{1:2}, at: hci_le_create_big_complete_evt+0xdb/0xae0 net/bluetooth/hci_event.c:6915
CPU: 0 PID: 5070 Comm: kworker/u9:2 Not tainted 6.8.0-syzkaller-08073-g480e035fc4c7 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024
Workqueue: hci0 hci_rx_work
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114
__might_resched+0x5d4/0x780 kernel/sched/core.c:10187
__mutex_lock_common kernel/locking/mutex.c:585 [inline]
__mutex_lock+0xc1/0xd70 kernel/locking/mutex.c:752
hci_connect_cfm include/net/bluetooth/hci_core.h:2004 [inline]
hci_le_create_big_complete_evt+0x3d9/0xae0 net/bluetooth/hci_event.c:6939
hci_event_func net/bluetooth/hci_event.c:7514 [inline]
hci_event_packet+0xa53/0x1540 net/bluetooth/hci_event.c:7569
hci_rx_work+0x3e8/0xca0 net/bluetooth/hci_core.c:4171
process_one_work kernel/workqueue.c:3254 [inline]
process_scheduled_works+0xa00/0x1770 kernel/workqueue.c:3335
worker_thread+0x86d/0xd70 kernel/workqueue.c:3416
kthread+0x2f0/0x390 kernel/kthread.c:388
ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:243
</TASK>
Reported-by: syzbot+2fb0835e0c9cefc34614@syzkaller.appspotmail.com
Tested-by: syzbot+2fb0835e0c9cefc34614@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=2fb0835e0c9cefc34614
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f91a5b8089389eb408501af2762f168c3aaa7b79 ]
Blamed commit forgot MSG_PEEK case, allowing a crash [1] as found
by syzbot.
Rework vlan_get_protocol_dgram() to not touch skb at all,
so that it can be used from many cpus on the same skb.
Add a const qualifier to skb argument.
[1]
skbuff: skb_under_panic: text:ffffffff8a8ccd05 len:29 put:14 head:ffff88807fc8e400 data:ffff88807fc8e3f4 tail:0x11 end:0x140 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:206 !
Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 1 UID: 0 PID: 5892 Comm: syz-executor883 Not tainted 6.13.0-rc4-syzkaller-00054-gd6ef8b40d075 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
RIP: 0010:skb_panic net/core/skbuff.c:206 [inline]
RIP: 0010:skb_under_panic+0x14b/0x150 net/core/skbuff.c:216
Code: 0b 8d 48 c7 c6 86 d5 25 8e 48 8b 54 24 08 8b 0c 24 44 8b 44 24 04 4d 89 e9 50 41 54 41 57 41 56 e8 5a 69 79 f7 48 83 c4 20 90 <0f> 0b 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3
RSP: 0018:ffffc900038d7638 EFLAGS: 00010282
RAX: 0000000000000087 RBX: dffffc0000000000 RCX: 609ffd18ea660600
RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000
RBP: ffff88802483c8d0 R08: ffffffff817f0a8c R09: 1ffff9200071ae60
R10: dffffc0000000000 R11: fffff5200071ae61 R12: 0000000000000140
R13: ffff88807fc8e400 R14: ffff88807fc8e3f4 R15: 0000000000000011
FS: 00007fbac5e006c0(0000) GS:ffff8880b8700000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fbac5e00d58 CR3: 000000001238e000 CR4: 00000000003526f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
skb_push+0xe5/0x100 net/core/skbuff.c:2636
vlan_get_protocol_dgram+0x165/0x290 net/packet/af_packet.c:585
packet_recvmsg+0x948/0x1ef0 net/packet/af_packet.c:3552
sock_recvmsg_nosec net/socket.c:1033 [inline]
sock_recvmsg+0x22f/0x280 net/socket.c:1055
____sys_recvmsg+0x1c6/0x480 net/socket.c:2803
___sys_recvmsg net/socket.c:2845 [inline]
do_recvmmsg+0x426/0xab0 net/socket.c:2940
__sys_recvmmsg net/socket.c:3014 [inline]
__do_sys_recvmmsg net/socket.c:3037 [inline]
__se_sys_recvmmsg net/socket.c:3030 [inline]
__x64_sys_recvmmsg+0x199/0x250 net/socket.c:3030
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: 79eecf631c14 ("af_packet: Handle outgoing VLAN packets without hardware offloading")
Reported-by: syzbot+74f70bb1cb968bf09e4f@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/6772c485.050a0220.2f3838.04c5.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Chengen Du <chengen.du@canonical.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20241230161004.2681892-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 542ed8145e6f9392e3d0a86a0e9027d2ffd183e4 ]
Access to genmask field in struct nft_set_ext results in unaligned
atomic read:
[ 72.130109] Unable to handle kernel paging request at virtual address ffff0000c2bb708c
[ 72.131036] Mem abort info:
[ 72.131213] ESR = 0x0000000096000021
[ 72.131446] EC = 0x25: DABT (current EL), IL = 32 bits
[ 72.132209] SET = 0, FnV = 0
[ 72.133216] EA = 0, S1PTW = 0
[ 72.134080] FSC = 0x21: alignment fault
[ 72.135593] Data abort info:
[ 72.137194] ISV = 0, ISS = 0x00000021, ISS2 = 0x00000000
[ 72.142351] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 72.145989] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 72.150115] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000237d27000
[ 72.154893] [ffff0000c2bb708c] pgd=0000000000000000, p4d=180000023ffff403, pud=180000023f84b403, pmd=180000023f835403,
+pte=0068000102bb7707
[ 72.163021] Internal error: Oops: 0000000096000021 [#1] SMP
[...]
[ 72.170041] CPU: 7 UID: 0 PID: 54 Comm: kworker/7:0 Tainted: G E 6.13.0-rc3+ #2
[ 72.170509] Tainted: [E]=UNSIGNED_MODULE
[ 72.170720] Hardware name: QEMU QEMU Virtual Machine, BIOS edk2-stable202302-for-qemu 03/01/2023
[ 72.171192] Workqueue: events_power_efficient nft_rhash_gc [nf_tables]
[ 72.171552] pstate: 21400005 (nzCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
[ 72.171915] pc : nft_rhash_gc+0x200/0x2d8 [nf_tables]
[ 72.172166] lr : nft_rhash_gc+0x128/0x2d8 [nf_tables]
[ 72.172546] sp : ffff800081f2bce0
[ 72.172724] x29: ffff800081f2bd40 x28: ffff0000c2bb708c x27: 0000000000000038
[ 72.173078] x26: ffff0000c6780ef0 x25: ffff0000c643df00 x24: ffff0000c6778f78
[ 72.173431] x23: 000000000000001a x22: ffff0000c4b1f000 x21: ffff0000c6780f78
[ 72.173782] x20: ffff0000c2bb70dc x19: ffff0000c2bb7080 x18: 0000000000000000
[ 72.174135] x17: ffff0000c0a4e1c0 x16: 0000000000003000 x15: 0000ac26d173b978
[ 72.174485] x14: ffffffffffffffff x13: 0000000000000030 x12: ffff0000c6780ef0
[ 72.174841] x11: 0000000000000000 x10: ffff800081f2bcf8 x9 : ffff0000c3000000
[ 72.175193] x8 : 00000000000004be x7 : 0000000000000000 x6 : 0000000000000000
[ 72.175544] x5 : 0000000000000040 x4 : ffff0000c3000010 x3 : 0000000000000000
[ 72.175871] x2 : 0000000000003a98 x1 : ffff0000c2bb708c x0 : 0000000000000004
[ 72.176207] Call trace:
[ 72.176316] nft_rhash_gc+0x200/0x2d8 [nf_tables] (P)
[ 72.176653] process_one_work+0x178/0x3d0
[ 72.176831] worker_thread+0x200/0x3f0
[ 72.176995] kthread+0xe8/0xf8
[ 72.177130] ret_from_fork+0x10/0x20
[ 72.177289] Code: 54fff984 d503201f d2800080 91003261 (f820303f)
[ 72.177557] ---[ end trace 0000000000000000 ]---
Align struct nft_set_ext to word size to address this and
documentation it.
pahole reports that this increases the size of elements for rhash and
pipapo in 8 bytes on x86_64.
Fixes: 7ffc7481153b ("netfilter: nft_set_hash: skip duplicated elements pending gc run")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ac931d4cdec3df8b6eac3bc40a6871123021f078 ]
Today ipip devices in collect-metadata mode don't allow for sending FOU
or GUE encapsulated packets. This patch lifts the restriction by adding
a struct ip_tunnel_encap to the tunnel metadata.
On the egress path, the members of this struct can be set by the
bpf_skb_set_fou_encap kfunc via a BPF tc-hook. Instead of dropping packets
wishing to use additional UDP encapsulation, ip_md_tunnel_xmit now
evaluates the contents of this struct and adds the corresponding FOU or
GUE header. Furthermore, it is making sure that additional header bytes
are taken into account for PMTU discovery.
On the ingress path, an ipip device in collect-metadata mode will fill this
struct and a BPF tc-hook can obtain the information via a call to the
bpf_skb_get_fou_encap kfunc.
The minor change to ip_tunnel_encap, which now takes a pointer to
struct ip_tunnel_encap instead of struct ip_tunnel, allows us to control
FOU encap type and parameters on a per packet-level.
Signed-off-by: Christian Ehrig <cehrig@cloudflare.com>
Link: https://lore.kernel.org/r/cfea47de655d0f870248abf725932f851b53960a.1680874078.git.cehrig@cloudflare.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: b5a7b661a073 ("net: Fix netns for ip_tunnel_init_flow()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e05feab22fd7dabcd6d272c4e2401ec1acdfdb9b ]
Different core device types such as PFs and VFs shouldn't be affiliated
together since they have different capabilities, fix that by enforcing
type check before doing the affiliation.
Fixes: 32f69e4be269 ("{net, IB}/mlx5: Manage port association for multiport RoCE")
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Link: https://patch.msgid.link/88699500f690dff1c1852c1ddb71f8a1cc8b956e.1733233480.git.leonro@nvidia.com
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit bcc80dec91ee745b3d66f3e48f0ec2efdea97149 upstream.
read_hv_sched_clock_tsc() assumes that the Hyper-V clock counter is
bigger than the variable hv_sched_clock_offset, which is cached during
early boot, but depending on the timing this assumption may be false
when a hibernated VM starts again (the clock counter starts from 0
again) and is resuming back (Note: hv_init_tsc_clocksource() is not
called during hibernation/resume); consequently,
read_hv_sched_clock_tsc() may return a negative integer (which is
interpreted as a huge positive integer since the return type is u64)
and new kernel messages are prefixed with huge timestamps before
read_hv_sched_clock_tsc() grows big enough (which typically takes
several seconds).
Fix the issue by saving the Hyper-V clock counter just before the
suspend, and using it to correct the hv_sched_clock_offset in
resume. This makes hv tsc page based sched_clock continuous and ensures
that post resume, it starts from where it left off during suspend.
Override x86_platform.save_sched_clock_state and
x86_platform.restore_sched_clock_state routines to correct this as soon
as possible.
Note: if Invariant TSC is available, the issue doesn't happen because
1) we don't register read_hv_sched_clock_tsc() for sched clock:
See commit e5313f1c5404 ("clocksource/drivers/hyper-v: Rework
clocksource and sched clock setup");
2) the common x86 code adjusts TSC similarly: see
__restore_processor_state() -> tsc_verify_tsc_adjust(true) and
x86_platform.restore_sched_clock_state().
Cc: stable@vger.kernel.org
Fixes: 1349401ff1aa ("clocksource/drivers/hyper-v: Suspend/resume Hyper-V clocksource for hibernation")
Co-developed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Naman Jain <namjain@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20240917053917.76787-1-namjain@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240917053917.76787-1-namjain@linux.microsoft.com>
Signed-off-by: Naman Jain <namjain@linux.microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 452f4b31e3f70a52b97890888eeb9eaa9a87139a upstream.
The name member of the struct trace_event_call is assigned with
generated string literals; declare them pointer to read-only.
Reported by clang:
security/landlock/syscalls.c:179:1: warning: initializing 'char *' with an expression of type 'const char[34]' discards qualifiers [-Wincompatible-pointer-types-discards-qualifiers]
179 | SYSCALL_DEFINE3(landlock_create_ruleset,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
180 | const struct landlock_ruleset_attr __user *const, attr,
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
181 | const size_t, size, const __u32, flags)
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/syscalls.h:226:36: note: expanded from macro 'SYSCALL_DEFINE3'
226 | #define SYSCALL_DEFINE3(name, ...) SYSCALL_DEFINEx(3, _##name, __VA_ARGS__)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/syscalls.h:234:2: note: expanded from macro 'SYSCALL_DEFINEx'
234 | SYSCALL_METADATA(sname, x, __VA_ARGS__) \
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/syscalls.h:184:2: note: expanded from macro 'SYSCALL_METADATA'
184 | SYSCALL_TRACE_ENTER_EVENT(sname); \
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/syscalls.h:151:30: note: expanded from macro 'SYSCALL_TRACE_ENTER_EVENT'
151 | .name = "sys_enter"#sname, \
| ^~~~~~~~~~~~~~~~~
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Mickaël Salaün <mic@digikod.net>
Cc: Günther Noack <gnoack@google.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Bill Wendling <morbo@google.com>
Cc: Justin Stitt <justinstitt@google.com>
Link: https://lore.kernel.org/20241125105028.42807-1-cgoettsche@seltendoof.de
Fixes: b77e38aa240c3 ("tracing: add event trace infrastructure")
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f718faf3940e95d5d34af9041f279f598396ab7d ]
Before commit:
f5d39b020809 ("freezer,sched: Rewrite core freezer logic")
the frozen task stat was reported as 'D' in cgroup v1.
However, after rewriting the core freezer logic, the frozen task stat is
reported as 'R'. This is confusing, especially when a task with stat of
'S' is frozen.
This bug can be reproduced with these steps:
$ cd /sys/fs/cgroup/freezer/
$ mkdir test
$ sleep 1000 &
[1] 739 // task whose stat is 'S'
$ echo 739 > test/cgroup.procs
$ echo FROZEN > test/freezer.state
$ ps -aux | grep 739
root 739 0.1 0.0 8376 1812 pts/0 R 10:56 0:00 sleep 1000
As shown above, a task whose stat is 'S' was changed to 'R' when it was
frozen.
To solve this regression, simply maintain the same reported state as
before the rewrite.
[ mingo: Enhanced the changelog and comments ]
Fixes: f5d39b020809 ("freezer,sched: Rewrite core freezer logic")
Signed-off-by: Chen Ridong <chenridong@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Michal Koutný <mkoutny@suse.com>
Link: https://lore.kernel.org/r/20241217004818.3200515-1-chenridong@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0d6b35283bcf1a379cf20066544af8e6a6b16b46 ]
task_state_index() ignores uninteresting state flags (such as
TASK_FREEZABLE) for most states, but for TASK_IDLE and TASK_RTLOCK_WAIT
it does not.
So if a task is waiting TASK_IDLE|TASK_FREEZABLE it gets incorrectly
reported as TASK_UNINTERRUPTIBLE or "D". (it is planned for nfsd to
change to use this state).
Fix this by only testing the interesting bits and not the irrelevant
bits in __task_state_index()
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/169335025927.5133.4781141800413736103@noble.neil.brown.name
Stable-dep-of: f718faf3940e ("freezer, sched: Report frozen tasks as 'D' instead of 'R'")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 724c6ce38bbaeb4b3f109b0e066d6c0ecd15446c ]
For the most part of the C++ history, it couldn't have type
declarations inside anonymous unions for different reasons. At the
same time, __struct_group() relies on the latters, so when the @TAG
argument is not empty, C++ code doesn't want to build (even under
`extern "C"`):
../linux/include/uapi/linux/pkt_cls.h:25:24: error:
'struct tc_u32_sel::<unnamed union>::tc_u32_sel_hdr,' invalid;
an anonymous union may only have public non-static data members
[-fpermissive]
The safest way to fix this without trying to switch standards (which
is impossible in UAPI anyway) etc., is to disable tag declaration
for that language. This won't break anything since for now it's not
buildable at all.
Use a separate definition for __struct_group() when __cplusplus is
defined to mitigate the error, including the version from tools/.
Fixes: 50d7bd38c3aa ("stddef: Introduce struct_group() helper macro")
Reported-by: Christopher Ferris <cferris@google.com>
Closes: https://lore.kernel.org/linux-hardening/Z1HZpe3WE5As8UAz@google.com
Suggested-by: Kees Cook <kees@kernel.org> # __struct_group_tag()
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20241219135734.2130002-1-aleksander.lobakin@intel.com
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d888b7af7c149c115dd6ac772cc11c375da3e17c ]
When we do sk_psock_verdict_apply->sk_psock_skb_ingress, an sk_msg will
be created out of the skb, and the rmem accounting of the sk_msg will be
handled by the skb.
For skmsgs in __SK_REDIRECT case of tcp_bpf_send_verdict, when redirecting
to the ingress of a socket, although we sk_rmem_schedule and add sk_msg to
the ingress_msg of sk_redir, we do not update sk_rmem_alloc. As a result,
except for the global memory limit, the rmem of sk_redir is nearly
unlimited. Thus, add sk_rmem_alloc related logic to limit the recv buffer.
Since the function sk_msg_recvmsg and __sk_psock_purge_ingress_msg are
used in these two paths. We use "msg->skb" to test whether the sk_msg is
skb backed up. If it's not, we shall do the memory accounting explicitly.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Zijian Zhang <zijianzhang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20241210012039.1669389-3-zijianzhang@bytedance.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 54f89b3178d5448dd4457afbb98fc1ab99090a65 ]
When bpf_tcp_ingress() is called, the skmsg is being redirected to the
ingress of the destination socket. Therefore, we should charge its
receive socket buffer, instead of sending socket buffer.
Because sk_rmem_schedule() tests pfmemalloc of skb, we need to
introduce a wrapper and call it for skmsg.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20241210012039.1669389-2-zijianzhang@bytedance.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 30c2de0a267c04046d89e678cc0067a9cfb455df ]
Fix the following clang compiler warning that is reported if the kernel is
built with W=1:
./include/linux/vmstat.h:518:36: error: arithmetic between different enumeration types ('enum node_stat_item' and 'enum lru_list') [-Werror,-Wenum-enum-conversion]
518 | return node_stat_name(NR_LRU_BASE + lru) + 3; // skip "nr_"
| ~~~~~~~~~~~ ^ ~~~
Link: https://lkml.kernel.org/r/20241212213126.1269116-1-bvanassche@acm.org
Fixes: 9d7ea9a297e6 ("mm/vmstat: add helpers to get vmstat item names for each enum type")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 900bbaae67e980945dec74d36f8afe0de7556d5a upstream.
Now, the epoll only use wake_up() interface to wake up task.
However, sometimes, there are epoll users which want to use
the synchronous wakeup flag to hint the scheduler, such as
Android binder driver.
So add a wake_up_sync() define, and use the wake_up_sync()
when the sync is true in ep_poll_callback().
Co-developed-by: Jing Xia <jing.xia@unisoc.com>
Signed-off-by: Jing Xia <jing.xia@unisoc.com>
Signed-off-by: Xuewen Yan <xuewen.yan@unisoc.com>
Link: https://lore.kernel.org/r/20240426080548.8203-1-xuewen.yan@unisoc.com
Tested-by: Brian Geffon <bgeffon@google.com>
Reviewed-by: Brian Geffon <bgeffon@google.com>
Reported-by: Benoit Lize <lizeb@google.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Cc: Brian Geffon <bgeffon@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 12d908116f7efd34f255a482b9afc729d7a5fb78 upstream.
Currently, io_uring_unreg_ringfd() (which cleans up registered rings) is
only called on exit, but __io_uring_free (which frees the tctx in which the
registered ring pointers are stored) is also called on execve (via
begin_new_exec -> io_uring_task_cancel -> __io_uring_cancel ->
io_uring_cancel_generic -> __io_uring_free).
This means: A process going through execve while having registered rings
will leak references to the rings' `struct file`.
Fix it by zapping registered rings on execve(). This is implemented by
moving the io_uring_unreg_ringfd() from io_uring_files_cancel() into its
callee __io_uring_cancel(), which is called from io_uring_task_cancel() on
execve.
This could probably be exploited *on 32-bit kernels* by leaking 2^32
references to the same ring, because the file refcount is stored in a
pointer-sized field and get_file() doesn't have protection against
refcount overflow, just a WARN_ONCE(); but on 64-bit it should have no
impact beyond a memory leak.
Cc: stable@vger.kernel.org
Fixes: e7a6c00dc77a ("io_uring: add support for registering ring file descriptors")
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20241218-uring-reg-ring-cleanup-v1-1-8f63e999045b@google.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 07a756a49f4b4290b49ea46e089cbe6f79ff8d26 upstream.
If the KVP (or VSS) daemon starts before the VMBus channel's ringbuffer is
fully initialized, we can hit the panic below:
hv_utils: Registering HyperV Utility Driver
hv_vmbus: registering driver hv_utils
...
BUG: kernel NULL pointer dereference, address: 0000000000000000
CPU: 44 UID: 0 PID: 2552 Comm: hv_kvp_daemon Tainted: G E 6.11.0-rc3+ #1
RIP: 0010:hv_pkt_iter_first+0x12/0xd0
Call Trace:
...
vmbus_recvpacket
hv_kvp_onchannelcallback
vmbus_on_event
tasklet_action_common
tasklet_action
handle_softirqs
irq_exit_rcu
sysvec_hyperv_stimer0
</IRQ>
<TASK>
asm_sysvec_hyperv_stimer0
...
kvp_register_done
hvt_op_read
vfs_read
ksys_read
__x64_sys_read
This can happen because the KVP/VSS channel callback can be invoked
even before the channel is fully opened:
1) as soon as hv_kvp_init() -> hvutil_transport_init() creates
/dev/vmbus/hv_kvp, the kvp daemon can open the device file immediately and
register itself to the driver by writing a message KVP_OP_REGISTER1 to the
file (which is handled by kvp_on_msg() ->kvp_handle_handshake()) and
reading the file for the driver's response, which is handled by
hvt_op_read(), which calls hvt->on_read(), i.e. kvp_register_done().
2) the problem with kvp_register_done() is that it can cause the
channel callback to be called even before the channel is fully opened,
and when the channel callback is starting to run, util_probe()->
vmbus_open() may have not initialized the ringbuffer yet, so the
callback can hit the panic of NULL pointer dereference.
To reproduce the panic consistently, we can add a "ssleep(10)" for KVP in
__vmbus_open(), just before the first hv_ringbuffer_init(), and then we
unload and reload the driver hv_utils, and run the daemon manually within
the 10 seconds.
Fix the panic by reordering the steps in util_probe() so the char dev
entry used by the KVP or VSS daemon is not created until after
vmbus_open() has completed. This reordering prevents the race condition
from happening.
Reported-by: Dexuan Cui <decui@microsoft.com>
Fixes: e0fa3e5e7df6 ("Drivers: hv: utils: fix a race on userspace daemons registration")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20241106154247.2271-3-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20241106154247.2271-3-mhklinux@outlook.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 144d204df78e40e6250201e71ef7d0e42d2a13fc ]
Introduce pci_resource_n() and replace open-coded implementations of it
in pci.h.
Link: https://lore.kernel.org/r/20230330162434.35055-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Stable-dep-of: 360c400d0f56 ("p2sb: Do not scan and remove the P2SB device when it is unhidden")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 349f0086ba8b2a169877d21ff15a4d9da3a60054 upstream.
In 32-bit x86 builds CONFIG_STATIC_CALL_INLINE isn't set, leading to
static_call_initialized not being available.
Define it as "0" in that case.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 0ef8047b737d ("x86/static-call: provide a way to do very early static-call updates")
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0ef8047b737d7480a5d4c46d956e97c190f13050 upstream.
Add static_call_update_early() for updating static-call targets in
very early boot.
This will be needed for support of Xen guest type specific hypercall
functions.
This is part of XSA-466 / CVE-2024-53241.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Co-developed-by: Peter Zijlstra <peterz@infradead.org>
Co-developed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 29a651451e6c264f58cd9d9a26088e579d17b242 ]
The voice setting is used by sco_connect() or sco_conn_defer_accept()
after being set by sco_sock_setsockopt().
The PCM part of the voice setting is used for offload mode through PCM
chipset port.
This commits add support for mSBC 16 bits offloading, i.e. audio data
not transported over HCI.
The BCM4349B1 supports 16 bits transparent data on its I2S port.
If BT_VOICE_TRANSPARENT is used when accepting a SCO connection, this
gives only garbage audio while using BT_VOICE_TRANSPARENT_16BIT gives
correct audio.
This has been tested with connection to iPhone 14 and Samsung S24.
Fixes: ad10b1a48754 ("Bluetooth: Add Bluetooth socket voice option")
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b454abfab52543c44b581afc807b9f97fc1e7a3a ]
The Felix DSA driver presents unique challenges that make the simplistic
ocelot PTP TX timestamping procedure unreliable: any transmitted packet
may be lost in hardware before it ever leaves our local system.
This may happen because there is congestion on the DSA conduit, the
switch CPU port or even user port (Qdiscs like taprio may delay packets
indefinitely by design).
The technical problem is that the kernel, i.e. ocelot_port_add_txtstamp_skb(),
runs out of timestamp IDs eventually, because it never detects that
packets are lost, and keeps the IDs of the lost packets on hold
indefinitely. The manifestation of the issue once the entire timestamp
ID range becomes busy looks like this in dmesg:
mscc_felix 0000:00:00.5: port 0 delivering skb without TX timestamp
mscc_felix 0000:00:00.5: port 1 delivering skb without TX timestamp
At the surface level, we need a timeout timer so that the kernel knows a
timestamp ID is available again. But there is a deeper problem with the
implementation, which is the monotonically increasing ocelot_port->ts_id.
In the presence of packet loss, it will be impossible to detect that and
reuse one of the holes created in the range of free timestamp IDs.
What we actually need is a bitmap of 63 timestamp IDs tracking which one
is available. That is able to use up holes caused by packet loss, but
also gives us a unique opportunity to not implement an actual timer_list
for the timeout timer (very complicated in terms of locking).
We could only declare a timestamp ID stale on demand (lazily), aka when
there's no other timestamp ID available. There are pros and cons to this
approach: the implementation is much more simple than per-packet timers
would be, but most of the stale packets would be quasi-leaked - not
really leaked, but blocked in driver memory, since this algorithm sees
no reason to free them.
An improved technique would be to check for stale timestamp IDs every
time we allocate a new one. Assuming a constant flux of PTP packets,
this avoids stale packets being blocked in memory, but of course,
packets lost at the end of the flux are still blocked until the flux
resumes (nobody left to kick them out).
Since implementing per-packet timers is way too complicated, this should
be good enough.
Testing procedure:
Persistently block traffic class 5 and try to run PTP on it:
$ tc qdisc replace dev swp3 parent root taprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 sched-entry S 0xdf 100000 flags 0x2
[ 126.948141] mscc_felix 0000:00:00.5: port 3 tc 5 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
$ ptp4l -i swp3 -2 -P -m --socket_priority 5 --fault_reset_interval ASAP --logSyncInterval -3
ptp4l[70.351]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.354]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.358]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 70.394583] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[70.406]: timed out while polling for tx timestamp
ptp4l[70.406]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[70.406]: port 1 (swp3): send peer delay response failed
ptp4l[70.407]: port 1 (swp3): clearing fault immediately
ptp4l[70.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 71.394858] mscc_felix 0000:00:00.5: port 3 timestamp id 1
ptp4l[71.400]: timed out while polling for tx timestamp
ptp4l[71.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[71.401]: port 1 (swp3): send peer delay response failed
ptp4l[71.401]: port 1 (swp3): clearing fault immediately
[ 72.393616] mscc_felix 0000:00:00.5: port 3 timestamp id 2
ptp4l[72.401]: timed out while polling for tx timestamp
ptp4l[72.402]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[72.402]: port 1 (swp3): send peer delay response failed
ptp4l[72.402]: port 1 (swp3): clearing fault immediately
ptp4l[72.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 73.395291] mscc_felix 0000:00:00.5: port 3 timestamp id 3
ptp4l[73.400]: timed out while polling for tx timestamp
ptp4l[73.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[73.400]: port 1 (swp3): send peer delay response failed
ptp4l[73.400]: port 1 (swp3): clearing fault immediately
[ 74.394282] mscc_felix 0000:00:00.5: port 3 timestamp id 4
ptp4l[74.400]: timed out while polling for tx timestamp
ptp4l[74.401]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[74.401]: port 1 (swp3): send peer delay response failed
ptp4l[74.401]: port 1 (swp3): clearing fault immediately
ptp4l[74.953]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 75.396830] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 75.405760] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[75.410]: timed out while polling for tx timestamp
ptp4l[75.411]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[75.411]: port 1 (swp3): send peer delay response failed
ptp4l[75.411]: port 1 (swp3): clearing fault immediately
(...)
Remove the blocking condition and see that the port recovers:
$ same tc command as above, but use "sched-entry S 0xff" instead
$ same ptp4l command as above
ptp4l[99.489]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.490]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.492]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 100.403768] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 100.412545] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 1 which seems lost
[ 100.421283] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 2 which seems lost
[ 100.430015] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 3 which seems lost
[ 100.438744] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 4 which seems lost
[ 100.447470] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 100.505919] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[100.963]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 101.405077] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 101.507953] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.405405] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.509391] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.406003] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.510011] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.405601] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.510624] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[104.965]: selected best master clock d858d7.fffe.00ca6d
ptp4l[104.966]: port 1 (swp3): assuming the grand master role
ptp4l[104.967]: port 1 (swp3): LISTENING to GRAND_MASTER on RS_GRAND_MASTER
[ 105.106201] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.232420] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.359001] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.405500] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.485356] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.511220] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.610938] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.737237] mscc_felix 0000:00:00.5: port 3 timestamp id 0
(...)
Notice that in this new usage pattern, a non-congested port should
basically use timestamp ID 0 all the time, progressing to higher numbers
only if there are unacknowledged timestamps in flight. Compare this to
the old usage, where the timestamp ID used to monotonically increase
modulo OCELOT_MAX_PTP_ID.
In terms of implementation, this simplifies the bookkeeping of the
ocelot_port :: ts_id and ptp_skbs_in_flight. Since we need to traverse
the list of two-step timestampable skbs for each new packet anyway, the
information can already be computed and does not need to be stored.
Also, ocelot_port->tx_skbs is always accessed under the switch-wide
ocelot->ts_id_lock IRQ-unsafe spinlock, so we don't need the skb queue's
lock and can use the unlocked primitives safely.
This problem was actually detected using the tc-taprio offload, and is
causing trouble in TSN scenarios, which Felix (NXP LS1028A / VSC9959)
supports but Ocelot (VSC7514) does not. Thus, I've selected the commit
to blame as the one adding initial timestamping support for the Felix
switch.
Fixes: c0bcf537667c ("net: dsa: ocelot: add hardware timestamping support for Felix")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0f6ede9fbc747e2553612271bce108f7517e7a45 upstream.
Ilya reported a slab-use-after-free in dst_destroy [1]
Issue is in xfrm6_net_init() and xfrm4_net_init() :
They copy xfrm[46]_dst_ops_template into net->xfrm.xfrm[46]_dst_ops.
But net structure might be freed before all the dst callbacks are
called. So when dst_destroy() calls later :
if (dst->ops->destroy)
dst->ops->destroy(dst);
dst->ops points to the old net->xfrm.xfrm[46]_dst_ops, which has been freed.
See a relevant issue fixed in :
ac888d58869b ("net: do not delay dst_entries_add() in dst_release()")
A fix is to queue the 'struct net' to be freed after one
another cleanup_net() round (and existing rcu_barrier())
[1]
BUG: KASAN: slab-use-after-free in dst_destroy (net/core/dst.c:112)
Read of size 8 at addr ffff8882137ccab0 by task swapper/37/0
Dec 03 05:46:18 kernel:
CPU: 37 UID: 0 PID: 0 Comm: swapper/37 Kdump: loaded Not tainted 6.12.0 #67
Hardware name: Red Hat KVM/RHEL, BIOS 1.16.1-1.el9 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl (lib/dump_stack.c:124)
print_address_description.constprop.0 (mm/kasan/report.c:378)
? dst_destroy (net/core/dst.c:112)
print_report (mm/kasan/report.c:489)
? dst_destroy (net/core/dst.c:112)
? kasan_addr_to_slab (mm/kasan/common.c:37)
kasan_report (mm/kasan/report.c:603)
? dst_destroy (net/core/dst.c:112)
? rcu_do_batch (kernel/rcu/tree.c:2567)
dst_destroy (net/core/dst.c:112)
rcu_do_batch (kernel/rcu/tree.c:2567)
? __pfx_rcu_do_batch (kernel/rcu/tree.c:2491)
? lockdep_hardirqs_on_prepare (kernel/locking/lockdep.c:4339 kernel/locking/lockdep.c:4406)
rcu_core (kernel/rcu/tree.c:2825)
handle_softirqs (kernel/softirq.c:554)
__irq_exit_rcu (kernel/softirq.c:589 kernel/softirq.c:428 kernel/softirq.c:637)
irq_exit_rcu (kernel/softirq.c:651)
sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1049 arch/x86/kernel/apic/apic.c:1049)
</IRQ>
<TASK>
asm_sysvec_apic_timer_interrupt (./arch/x86/include/asm/idtentry.h:702)
RIP: 0010:default_idle (./arch/x86/include/asm/irqflags.h:37 ./arch/x86/include/asm/irqflags.h:92 arch/x86/kernel/process.c:743)
Code: 00 4d 29 c8 4c 01 c7 4c 29 c2 e9 6e ff ff ff 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 66 90 0f 00 2d c7 c9 27 00 fb f4 <fa> c3 cc cc cc cc 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 90
RSP: 0018:ffff888100d2fe00 EFLAGS: 00000246
RAX: 00000000001870ed RBX: 1ffff110201a5fc2 RCX: ffffffffb61a3e46
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffffb3d4d123
RBP: 0000000000000000 R08: 0000000000000001 R09: ffffed11c7e1835d
R10: ffff888e3f0c1aeb R11: 0000000000000000 R12: 0000000000000000
R13: ffff888100d20000 R14: dffffc0000000000 R15: 0000000000000000
? ct_kernel_exit.constprop.0 (kernel/context_tracking.c:148)
? cpuidle_idle_call (kernel/sched/idle.c:186)
default_idle_call (./include/linux/cpuidle.h:143 kernel/sched/idle.c:118)
cpuidle_idle_call (kernel/sched/idle.c:186)
? __pfx_cpuidle_idle_call (kernel/sched/idle.c:168)
? lock_release (kernel/locking/lockdep.c:467 kernel/locking/lockdep.c:5848)
? lockdep_hardirqs_on_prepare (kernel/locking/lockdep.c:4347 kernel/locking/lockdep.c:4406)
? tsc_verify_tsc_adjust (arch/x86/kernel/tsc_sync.c:59)
do_idle (kernel/sched/idle.c:326)
cpu_startup_entry (kernel/sched/idle.c:423 (discriminator 1))
start_secondary (arch/x86/kernel/smpboot.c:202 arch/x86/kernel/smpboot.c:282)
? __pfx_start_secondary (arch/x86/kernel/smpboot.c:232)
? soft_restart_cpu (arch/x86/kernel/head_64.S:452)
common_startup_64 (arch/x86/kernel/head_64.S:414)
</TASK>
Dec 03 05:46:18 kernel:
Allocated by task 12184:
kasan_save_stack (mm/kasan/common.c:48)
kasan_save_track (./arch/x86/include/asm/current.h:49 mm/kasan/common.c:60 mm/kasan/common.c:69)
__kasan_slab_alloc (mm/kasan/common.c:319 mm/kasan/common.c:345)
kmem_cache_alloc_noprof (mm/slub.c:4085 mm/slub.c:4134 mm/slub.c:4141)
copy_net_ns (net/core/net_namespace.c:421 net/core/net_namespace.c:480)
create_new_namespaces (kernel/nsproxy.c:110)
unshare_nsproxy_namespaces (kernel/nsproxy.c:228 (discriminator 4))
ksys_unshare (kernel/fork.c:3313)
__x64_sys_unshare (kernel/fork.c:3382)
do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
Dec 03 05:46:18 kernel:
Freed by task 11:
kasan_save_stack (mm/kasan/common.c:48)
kasan_save_track (./arch/x86/include/asm/current.h:49 mm/kasan/common.c:60 mm/kasan/common.c:69)
kasan_save_free_info (mm/kasan/generic.c:582)
__kasan_slab_free (mm/kasan/common.c:271)
kmem_cache_free (mm/slub.c:4579 mm/slub.c:4681)
cleanup_net (net/core/net_namespace.c:456 net/core/net_namespace.c:446 net/core/net_namespace.c:647)
process_one_work (kernel/workqueue.c:3229)
worker_thread (kernel/workqueue.c:3304 kernel/workqueue.c:3391)
kthread (kernel/kthread.c:389)
ret_from_fork (arch/x86/kernel/process.c:147)
ret_from_fork_asm (arch/x86/entry/entry_64.S:257)
Dec 03 05:46:18 kernel:
Last potentially related work creation:
kasan_save_stack (mm/kasan/common.c:48)
__kasan_record_aux_stack (mm/kasan/generic.c:541)
insert_work (./include/linux/instrumented.h:68 ./include/asm-generic/bitops/instrumented-non-atomic.h:141 kernel/workqueue.c:788 kernel/workqueue.c:795 kernel/workqueue.c:2186)
__queue_work (kernel/workqueue.c:2340)
queue_work_on (kernel/workqueue.c:2391)
xfrm_policy_insert (net/xfrm/xfrm_policy.c:1610)
xfrm_add_policy (net/xfrm/xfrm_user.c:2116)
xfrm_user_rcv_msg (net/xfrm/xfrm_user.c:3321)
netlink_rcv_skb (net/netlink/af_netlink.c:2536)
xfrm_netlink_rcv (net/xfrm/xfrm_user.c:3344)
netlink_unicast (net/netlink/af_netlink.c:1316 net/netlink/af_netlink.c:1342)
netlink_sendmsg (net/netlink/af_netlink.c:1886)
sock_write_iter (net/socket.c:729 net/socket.c:744 net/socket.c:1165)
vfs_write (fs/read_write.c:590 fs/read_write.c:683)
ksys_write (fs/read_write.c:736)
do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
Dec 03 05:46:18 kernel:
Second to last potentially related work creation:
kasan_save_stack (mm/kasan/common.c:48)
__kasan_record_aux_stack (mm/kasan/generic.c:541)
insert_work (./include/linux/instrumented.h:68 ./include/asm-generic/bitops/instrumented-non-atomic.h:141 kernel/workqueue.c:788 kernel/workqueue.c:795 kernel/workqueue.c:2186)
__queue_work (kernel/workqueue.c:2340)
queue_work_on (kernel/workqueue.c:2391)
__xfrm_state_insert (./include/linux/workqueue.h:723 net/xfrm/xfrm_state.c:1150 net/xfrm/xfrm_state.c:1145 net/xfrm/xfrm_state.c:1513)
xfrm_state_update (./include/linux/spinlock.h:396 net/xfrm/xfrm_state.c:1940)
xfrm_add_sa (net/xfrm/xfrm_user.c:912)
xfrm_user_rcv_msg (net/xfrm/xfrm_user.c:3321)
netlink_rcv_skb (net/netlink/af_netlink.c:2536)
xfrm_netlink_rcv (net/xfrm/xfrm_user.c:3344)
netlink_unicast (net/netlink/af_netlink.c:1316 net/netlink/af_netlink.c:1342)
netlink_sendmsg (net/netlink/af_netlink.c:1886)
sock_write_iter (net/socket.c:729 net/socket.c:744 net/socket.c:1165)
vfs_write (fs/read_write.c:590 fs/read_write.c:683)
ksys_write (fs/read_write.c:736)
do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
Fixes: a8a572a6b5f2 ("xfrm: dst_entries_init() per-net dst_ops")
Reported-by: Ilya Maximets <i.maximets@ovn.org>
Closes: https://lore.kernel.org/netdev/CANn89iKKYDVpB=MtmfH7nyv2p=rJWSLedO5k7wSZgtY_tO8WQg@mail.gmail.com/T/#m02c98c3009fe66382b73cfb4db9cf1df6fab3fbf
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20241204125455.3871859-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a6d75ecee2bf828ac6a1b52724aba0a977e4eaf4 ]
It is unclear if net/lapb code is supposed to be ready for 8021q.
We can at least avoid crashes like the following :
skbuff: skb_under_panic: text:ffffffff8aabe1f6 len:24 put:20 head:ffff88802824a400 data:ffff88802824a3fe tail:0x16 end:0x140 dev:nr0.2
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:206 !
Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 1 UID: 0 PID: 5508 Comm: dhcpcd Not tainted 6.12.0-rc7-syzkaller-00144-g66418447d27b #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/30/2024
RIP: 0010:skb_panic net/core/skbuff.c:206 [inline]
RIP: 0010:skb_under_panic+0x14b/0x150 net/core/skbuff.c:216
Code: 0d 8d 48 c7 c6 2e 9e 29 8e 48 8b 54 24 08 8b 0c 24 44 8b 44 24 04 4d 89 e9 50 41 54 41 57 41 56 e8 1a 6f 37 02 48 83 c4 20 90 <0f> 0b 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3
RSP: 0018:ffffc90002ddf638 EFLAGS: 00010282
RAX: 0000000000000086 RBX: dffffc0000000000 RCX: 7a24750e538ff600
RDX: 0000000000000000 RSI: 0000000000000201 RDI: 0000000000000000
RBP: ffff888034a86650 R08: ffffffff8174b13c R09: 1ffff920005bbe60
R10: dffffc0000000000 R11: fffff520005bbe61 R12: 0000000000000140
R13: ffff88802824a400 R14: ffff88802824a3fe R15: 0000000000000016
FS: 00007f2a5990d740(0000) GS:ffff8880b8700000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000110c2631fd CR3: 0000000029504000 CR4: 00000000003526f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
skb_push+0xe5/0x100 net/core/skbuff.c:2636
nr_header+0x36/0x320 net/netrom/nr_dev.c:69
dev_hard_header include/linux/netdevice.h:3148 [inline]
vlan_dev_hard_header+0x359/0x480 net/8021q/vlan_dev.c:83
dev_hard_header include/linux/netdevice.h:3148 [inline]
lapbeth_data_transmit+0x1f6/0x2a0 drivers/net/wan/lapbether.c:257
lapb_data_transmit+0x91/0xb0 net/lapb/lapb_iface.c:447
lapb_transmit_buffer+0x168/0x1f0 net/lapb/lapb_out.c:149
lapb_establish_data_link+0x84/0xd0
lapb_device_event+0x4e0/0x670
notifier_call_chain+0x19f/0x3e0 kernel/notifier.c:93
__dev_notify_flags+0x207/0x400
dev_change_flags+0xf0/0x1a0 net/core/dev.c:8922
devinet_ioctl+0xa4e/0x1aa0 net/ipv4/devinet.c:1188
inet_ioctl+0x3d7/0x4f0 net/ipv4/af_inet.c:1003
sock_do_ioctl+0x158/0x460 net/socket.c:1227
sock_ioctl+0x626/0x8e0 net/socket.c:1346
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xf9/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+fb99d1b0c0f81d94a5e2@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/67506220.050a0220.17bd51.006c.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241204141031.4030267-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6365ba64b4dbe8b59ddaeaa724b281f3787715d5 ]
KVM_HC_CLOCK_PAIRING currently fails inside SEV-SNP guests because the
guest passes an address to static data to the host. In confidential
computing the host can't access arbitrary guest memory so handling the
hypercall runs into an "rmpfault". To make the hypercall work, the guest
needs to explicitly mark the memory as decrypted. Do that in
kvm_arch_ptp_init(), but retain the previous behavior for
non-confidential guests to save us from having to allocate memory.
Add a new arch-specific function (kvm_arch_ptp_exit()) to free the
allocation and mark the memory as encrypted again.
Signed-off-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Link: https://lore.kernel.org/r/20230308150531.477741-1-jpiotrowski@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 5e7aa97c7acf ("ptp: kvm: x86: Return EOPNOTSUPP instead of ENODEV from kvm_arch_ptp_init()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit dbd7a2a941b8cbf9e5f79a777ed9fe0090eebb61 upstream.
The existing no-op shims for when PM_DEVFREQ (or an individual governor)
only do half the job. The governor specific config/tuning structs need
to be available to avoid compile errors in drivers using devfreq.
Fixes: 6563f60f14cb ("drm/msm/gpu: Add devfreq tuning debugfs")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Patchwork: https://patchwork.freedesktop.org/patch/519801/
Link: https://lore.kernel.org/r/20230123153745.3185032-1-robdclark@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 71ce046327cfd3aef3f93d1c44e091395eb03f8f upstream.
Some drivers require the mapped tt pages to be decrypted. In an ideal
world this would have been handled by the dma layer, but the TTM page
fault handling would have to be rewritten to able to do that.
A side-effect of the TTM page fault handling is using a dma allocation
per order (via ttm_pool_alloc_page) which makes it impossible to just
trivially use dma_mmap_attrs. As a result ttm has to be very careful
about trying to make its pgprot for the mapped tt pages match what
the dma layer thinks it is. At the ttm layer it's possible to
deduce the requirement to have tt pages decrypted by checking
whether coherent dma allocations have been requested and the system
is running with confidential computing technologies.
This approach isn't ideal but keeping TTM matching DMAs expectations
for the page properties is in general fragile, unfortunately proper
fix would require a rewrite of TTM's page fault handling.
Fixes vmwgfx with SEV enabled.
v2: Explicitly include cc_platform.h
v3: Use CC_ATTR_GUEST_MEM_ENCRYPT instead of CC_ATTR_MEM_ENCRYPT to
limit the scope to guests and log when memory decryption is enabled.
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Fixes: 3bf3710e3718 ("drm/ttm: Add a generic TTM memcpy move for page-based iomem")
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # v5.14+
Link: https://patchwork.freedesktop.org/patch/msgid/20230926040359.3040017-1-zack@kde.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Ye Li <ye.li@broadcom.com>
Signed-off-by: Ajay Kaher <ajay.kaher@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 34d21de99cea9cb17967874313e5b0262527833c ]
Move {l,t,d}stats allocation to the core and let netdevs pick the stats
type they need. That way the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc) - all happening in the core.
Co-developed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Cc: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20231114004220.6495-3-daniel@iogearbox.net
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Stable-dep-of: 024ee930cb3c ("bpf: Fix dev's rx stats for bpf_redirect_peer traffic")
[ Note: Simplified vrf bits to reduce patch given unrelated to the fix ]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 32556ce93bc45c730829083cb60f95a2728ea48b upstream.
Lonial found an issue that despite user- and BPF-side frozen BPF map
(like in case of .rodata), it was still possible to write into it from
a BPF program side through specific helpers having ARG_PTR_TO_{LONG,INT}
as arguments.
In check_func_arg() when the argument is as mentioned, the meta->raw_mode
is never set. Later, check_helper_mem_access(), under the case of
PTR_TO_MAP_VALUE as register base type, it assumes BPF_READ for the
subsequent call to check_map_access_type() and given the BPF map is
read-only it succeeds.
The helpers really need to be annotated as ARG_PTR_TO_{LONG,INT} | MEM_UNINIT
when results are written into them as opposed to read out of them. The
latter indicates that it's okay to pass a pointer to uninitialized memory
as the memory is written to anyway.
However, ARG_PTR_TO_{LONG,INT} is a special case of ARG_PTR_TO_FIXED_SIZE_MEM
just with additional alignment requirement. So it is better to just get
rid of the ARG_PTR_TO_{LONG,INT} special cases altogether and reuse the
fixed size memory types. For this, add MEM_ALIGNED to additionally ensure
alignment given these helpers write directly into the args via *<ptr> = val.
The .arg*_size has been initialized reflecting the actual sizeof(*<ptr>).
MEM_ALIGNED can only be used in combination with MEM_FIXED_SIZE annotated
argument types, since in !MEM_FIXED_SIZE cases the verifier does not know
the buffer size a priori and therefore cannot blindly write *<ptr> = val.
Fixes: 57c3bb725a3d ("bpf: Introduce ARG_PTR_TO_{INT,LONG} arg types")
Reported-by: Lonial Con <kongln9170@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Link: https://lore.kernel.org/r/20240913191754.13290-3-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
[ Resolve merge conflict in include/linux/bpf.h and merge conflict in
kernel/bpf/verifier.c.]
Signed-off-by: Bin Lan <bin.lan.cn@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c462d56487e3abdbf8a61cedfe7c795a54f4a78 upstream.
SMCCCv1.3 added a hint bit which callers can set in an SMCCC function ID
(AKA "FID") to indicate that it is acceptable for the SMCCC
implementation to discard SVE and/or SME state over a specific SMCCC
call. The kernel support for using this hint is broken and SMCCC calls
may clobber the SVE and/or SME state of arbitrary tasks, though FPSIMD
state is unaffected.
The kernel support is intended to use the hint when there is no SVE or
SME state to save, and to do this it checks whether TIF_FOREIGN_FPSTATE
is set or TIF_SVE is clear in assembly code:
| ldr <flags>, [<current_task>, #TSK_TI_FLAGS]
| tbnz <flags>, #TIF_FOREIGN_FPSTATE, 1f // Any live FP state?
| tbnz <flags>, #TIF_SVE, 2f // Does that state include SVE?
|
| 1: orr <fid>, <fid>, ARM_SMCCC_1_3_SVE_HINT
| 2:
| << SMCCC call using FID >>
This is not safe as-is:
(1) SMCCC calls can be made in a preemptible context and preemption can
result in TIF_FOREIGN_FPSTATE being set or cleared at arbitrary
points in time. Thus checking for TIF_FOREIGN_FPSTATE provides no
guarantee.
(2) TIF_FOREIGN_FPSTATE only indicates that the live FP/SVE/SME state in
the CPU does not belong to the current task, and does not indicate
that clobbering this state is acceptable.
When the live CPU state is clobbered it is necessary to update
fpsimd_last_state.st to ensure that a subsequent context switch will
reload FP/SVE/SME state from memory rather than consuming the
clobbered state. This and the SMCCC call itself must happen in a
critical section with preemption disabled to avoid races.
(3) Live SVE/SME state can exist with TIF_SVE clear (e.g. with only
TIF_SME set), and checking TIF_SVE alone is insufficient.
Remove the broken support for the SMCCCv1.3 SVE saving hint. This is
effectively a revert of commits:
* cfa7ff959a78 ("arm64: smccc: Support SMCCC v1.3 SVE register saving hint")
* a7c3acca5380 ("arm64: smccc: Save lr before calling __arm_smccc_sve_check()")
... leaving behind the ARM_SMCCC_VERSION_1_3 and ARM_SMCCC_1_3_SVE_HINT
definitions, since these are simply definitions from the SMCCC
specification, and the latter is used in KVM via ARM_SMCCC_CALL_HINTS.
If we want to bring this back in future, we'll probably want to handle
this logic in C where we can use all the usual FPSIMD/SVE/SME helper
functions, and that'll likely require some rework of the SMCCC code
and/or its callers.
Fixes: cfa7ff959a78 ("arm64: smccc: Support SMCCC v1.3 SVE register saving hint")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20241106160448.2712997-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
[ Mark: fix conflicts in <linux/arm-smccc.h> ]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7738a7ab9d12c5371ed97114ee2132d4512e9fd5 ]
Add a quirk similar to eeprom_93xx46 to add an extra clock cycle before
reading data from the EEPROM.
The 93Cx6 family of EEPROMs output a "dummy 0 bit" between the writing
of the op-code/address from the host to the EEPROM and the reading of
the actual data from the EEPROM.
More info can be found on page 6 of the AT93C46 datasheet (linked below).
Similar notes are found in other 93xx6 datasheets.
In summary the read operation for a 93Cx6 EEPROM is:
Write to EEPROM: 110[A5-A0] (9 bits)
Read from EEPROM: 0[D15-D0] (17 bits)
Where:
110 is the start bit and READ OpCode
[A5-A0] is the address to read from
0 is a "dummy bit" preceding the actual data
[D15-D0] is the actual data.
Looking at the READ timing diagrams in the 93Cx6 datasheets the dummy
bit should be clocked out on the last address bit clock cycle meaning it
should be discarded naturally.
However, depending on the hardware configuration sometimes this dummy
bit is not discarded. This is the case with Exar PCI UARTs which require
an extra clock cycle between sending the address and reading the data.
Datasheet: https://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-5193-SEEPROM-AT93C46D-Datasheet.pdf
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/0f23973efefccd2544705a0480b4ad4c2353e407.1727880931.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3b96b895127b7c0aed63d82c974b46340e8466c1 ]
Some computers with CPUs that lack Thunderbolt features use discrete
Thunderbolt chips to add Thunderbolt functionality. These Thunderbolt
chips are located within the chassis; between the Root Port labeled
ExternalFacingPort and the USB-C port.
These Thunderbolt PCIe devices should be labeled as fixed and trusted, as
they are built into the computer. Otherwise, security policies that rely on
those flags may have unintended results, such as preventing USB-C ports
from enumerating.
Detect the above scenario through the process of elimination.
1) Integrated Thunderbolt host controllers already have Thunderbolt
implemented, so anything outside their external facing Root Port is
removable and untrusted.
Detect them using the following properties:
- Most integrated host controllers have the "usb4-host-interface"
ACPI property, as described here:
https://learn.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#mapping-native-protocols-pcie-displayport-tunneled-through-usb4-to-usb4-host-routers
- Integrated Thunderbolt PCIe Root Ports before Alder Lake do not
have the "usb4-host-interface" ACPI property. Identify those by
their PCI IDs instead.
2) If a Root Port does not have integrated Thunderbolt capabilities, but
has the "ExternalFacingPort" ACPI property, that means the
manufacturer has opted to use a discrete Thunderbolt host controller
that is built into the computer.
This host controller can be identified by virtue of being located
directly below an external-facing Root Port that lacks integrated
Thunderbolt. Label it as trusted and fixed.
Everything downstream from it is untrusted and removable.
The "ExternalFacingPort" ACPI property is described here:
https://learn.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#identifying-externally-exposed-pcie-root-ports
Link: https://lore.kernel.org/r/20240910-trust-tbt-fix-v5-1-7a7a42a5f496@chromium.org
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Esther Shimanovich <eshimanovich@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ca7cd938725a4050dcd62ae9472e931d603118d ]
There is NULL pointer issue observed if from Process A where hid device
being added which results in adding a led_cdev addition and later a
another call to access of led_cdev attribute from Process B can result
in NULL pointer issue.
Use mutex led_cdev->led_access to protect access to led->cdev and its
attribute inside brightness_show() and max_brightness_show() and also
update the comment for mutex that it should be used to protect the led
class device fields.
Process A Process B
kthread+0x114
worker_thread+0x244
process_scheduled_works+0x248
uhid_device_add_worker+0x24
hid_add_device+0x120
device_add+0x268
bus_probe_device+0x94
device_initial_probe+0x14
__device_attach+0xfc
bus_for_each_drv+0x10c
__device_attach_driver+0x14c
driver_probe_device+0x3c
__driver_probe_device+0xa0
really_probe+0x190
hid_device_probe+0x130
ps_probe+0x990
ps_led_register+0x94
devm_led_classdev_register_ext+0x58
led_classdev_register_ext+0x1f8
device_create_with_groups+0x48
device_create_groups_vargs+0xc8
device_add+0x244
kobject_uevent+0x14
kobject_uevent_env[jt]+0x224
mutex_unlock[jt]+0xc4
__mutex_unlock_slowpath+0xd4
wake_up_q+0x70
try_to_wake_up[jt]+0x48c
preempt_schedule_common+0x28
__schedule+0x628
__switch_to+0x174
el0t_64_sync+0x1a8/0x1ac
el0t_64_sync_handler+0x68/0xbc
el0_svc+0x38/0x68
do_el0_svc+0x1c/0x28
el0_svc_common+0x80/0xe0
invoke_syscall+0x58/0x114
__arm64_sys_read+0x1c/0x2c
ksys_read+0x78/0xe8
vfs_read+0x1e0/0x2c8
kernfs_fop_read_iter+0x68/0x1b4
seq_read_iter+0x158/0x4ec
kernfs_seq_show+0x44/0x54
sysfs_kf_seq_show+0xb4/0x130
dev_attr_show+0x38/0x74
brightness_show+0x20/0x4c
dualshock4_led_get_brightness+0xc/0x74
[ 3313.874295][ T4013] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000060
[ 3313.874301][ T4013] Mem abort info:
[ 3313.874303][ T4013] ESR = 0x0000000096000006
[ 3313.874305][ T4013] EC = 0x25: DABT (current EL), IL = 32 bits
[ 3313.874307][ T4013] SET = 0, FnV = 0
[ 3313.874309][ T4013] EA = 0, S1PTW = 0
[ 3313.874311][ T4013] FSC = 0x06: level 2 translation fault
[ 3313.874313][ T4013] Data abort info:
[ 3313.874314][ T4013] ISV = 0, ISS = 0x00000006, ISS2 = 0x00000000
[ 3313.874316][ T4013] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 3313.874318][ T4013] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 3313.874320][ T4013] user pgtable: 4k pages, 39-bit VAs, pgdp=00000008f2b0a000
..
[ 3313.874332][ T4013] Dumping ftrace buffer:
[ 3313.874334][ T4013] (ftrace buffer empty)
..
..
[ dd3313.874639][ T4013] CPU: 6 PID: 4013 Comm: InputReader
[ 3313.874648][ T4013] pc : dualshock4_led_get_brightness+0xc/0x74
[ 3313.874653][ T4013] lr : led_update_brightness+0x38/0x60
[ 3313.874656][ T4013] sp : ffffffc0b910bbd0
..
..
[ 3313.874685][ T4013] Call trace:
[ 3313.874687][ T4013] dualshock4_led_get_brightness+0xc/0x74
[ 3313.874690][ T4013] brightness_show+0x20/0x4c
[ 3313.874692][ T4013] dev_attr_show+0x38/0x74
[ 3313.874696][ T4013] sysfs_kf_seq_show+0xb4/0x130
[ 3313.874700][ T4013] kernfs_seq_show+0x44/0x54
[ 3313.874703][ T4013] seq_read_iter+0x158/0x4ec
[ 3313.874705][ T4013] kernfs_fop_read_iter+0x68/0x1b4
[ 3313.874708][ T4013] vfs_read+0x1e0/0x2c8
[ 3313.874711][ T4013] ksys_read+0x78/0xe8
[ 3313.874714][ T4013] __arm64_sys_read+0x1c/0x2c
[ 3313.874718][ T4013] invoke_syscall+0x58/0x114
[ 3313.874721][ T4013] el0_svc_common+0x80/0xe0
[ 3313.874724][ T4013] do_el0_svc+0x1c/0x28
[ 3313.874727][ T4013] el0_svc+0x38/0x68
[ 3313.874730][ T4013] el0t_64_sync_handler+0x68/0xbc
[ 3313.874732][ T4013] el0t_64_sync+0x1a8/0x1ac
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Reviewed-by: Anish Kumar <yesanishhere@gmail.com>
Link: https://lore.kernel.org/r/20241103160527.82487-1-quic_mojha@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 78bc671bd1501e2f6c571e063301a4fdc5db53b2 ]
Replace UFSHCD_QUIRK_BROKEN_64BIT_ADDRESS with
ufs_hba_variant_ops::set_dma_mask. Update the Renesas driver
accordingly. This patch enables supporting other configurations than
32-bit or 64-bit DMA addresses, e.g. 36-bit DMA addresses.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241018194753.775074-1-bvanassche@acm.org
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 13d750c2c03e9861e15268574ed2c239cca9c9d5 ]
In preparation for allowing system call enter/exit instrumentation to
handle page faults, make sure that ftrace can handle this change by
explicitly disabling preemption within the ftrace system call tracepoint
probes to respect the current expectations within ftrace ring buffer
code.
This change does not yet allow ftrace to take page faults per se within
its probe, but allows its existing probes to adapt to the upcoming
change.
Cc: Michael Jeanson <mjeanson@efficios.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Yonghong Song <yhs@fb.com>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Andrii Nakryiko <andrii.nakryiko@gmail.com>
Cc: bpf@vger.kernel.org
Cc: Joel Fernandes <joel@joelfernandes.org>
Link: https://lore.kernel.org/20241009010718.2050182-3-mathieu.desnoyers@efficios.com
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cd068d51594d9635bf6688fc78717572b78bce6a ]
GIGASTONE Gaming Plus microSD cards manufactured on 02/2022 report that
they support poweroff notification and cache, but they are not working
correctly.
Flush Cache bit never gets cleared in sd_flush_cache() and Poweroff
Notification Ready bit also never gets set to 1 within 1 second from the
end of busy of CMD49 in sd_poweroff_notify().
This leads to I/O error and runtime PM error state.
I observed that the same card manufactured on 01/2024 works as expected.
This problem seems similar to the Kingston cards fixed with
commit c467c8f08185 ("mmc: Add MMC_QUIRK_BROKEN_SD_CACHE for Kingston
Canvas Go Plus from 11/2019") and should be handled using quirks.
CID for the problematic card is here.
12345641535443002000000145016200
Manufacturer ID is 0x12 and defined as CID_MANFID_GIGASTONE as of now,
but would like comments on what naming is appropriate because MID list
is not public and not sure it's right.
Signed-off-by: Keita Aihara <keita.aihara@sony.com>
Link: https://lore.kernel.org/r/20240913094417.GA4191647@sony.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6474353a5e3d0b2cf610153cea0c61f576a36d0a ]
Epoll relies on a racy fastpath check during __fput() in
eventpoll_release() to avoid the hit of pointlessly acquiring a
semaphore. Annotate that race by using WRITE_ONCE() and READ_ONCE().
Link: https://lore.kernel.org/r/66edfb3c.050a0220.3195df.001a.GAE@google.com
Link: https://lore.kernel.org/r/20240925-fungieren-anbauen-79b334b00542@brauner
Reviewed-by: Jan Kara <jack@suse.cz>
Reported-by: syzbot+3b6b32dc50537a49bb4a@syzkaller.appspotmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a6fa67d26de385c3c7a23c1e109a0e23bfda4ec7 upstream.
If the MST topology is removed during the reception of an MST down reply
or MST up request sideband message, the
drm_dp_mst_topology_mgr::up_req_recv/down_rep_recv states could be reset
from one thread via drm_dp_mst_topology_mgr_set_mst(false), racing with
the reading/parsing of the message from another thread via
drm_dp_mst_handle_down_rep() or drm_dp_mst_handle_up_req(). The race is
possible since the reader/parser doesn't hold any lock while accessing
the reception state. This in turn can lead to a memory corruption in the
reader/parser as described by commit bd2fccac61b4 ("drm/dp_mst: Fix MST
sideband message body length check").
Fix the above by resetting the message reception state if needed before
reading/parsing a message. Another solution would be to hold the
drm_dp_mst_topology_mgr::lock for the whole duration of the message
reception/parsing in drm_dp_mst_handle_down_rep() and
drm_dp_mst_handle_up_req(), however this would require a bigger change.
Since the fix is also needed for stable, opting for the simpler solution
in this patch.
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org>
Fixes: 1d082618bbf3 ("drm/display/dp_mst: Fix down/up message handling after sink disconnect")
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/13056
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241203160223.2926014-2-imre.deak@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f45ed5f0cd5ccbbec79adc6c48a67d6a85fba56 upstream.
When the power mode change is successful but the power mode hasn't
actually changed, the post notification was missed. Similar to the
approach with hibernate/clock scale/hce enable, having pre/post
notifications in the same function will make it easier to maintain.
Additionally, supplement the description of power parameters for the
pwr_change_notify callback.
Fixes: 7eb584db73be ("ufs: refactor configuring power mode")
Cc: stable@vger.kernel.org #6.11.x
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20241122024943.30589-1-peter.wang@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d89c8ec0546184267cb211b579514ebaf8916100 ]
Fix a kernel-doc warning by making the kernel-doc function description
match the function name:
include/linux/scatterlist.h:323: warning: expecting prototype for sg_unmark_bus_address(). Prototype was for sg_dma_unmark_bus_address() instead
Link: https://lkml.kernel.org/r/20241130022406.537973-1-rdunlap@infradead.org
Fixes: 42399301203e ("lib/scatterlist: add flag for indicating P2PDMA segments in an SGL")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 365130fd47af6d4317aa16a407874b699ab8d8cb ]
Similar to recently propose for_each_child_of_node_scoped() this
new version of the loop macro instantiates a new local
struct fwnode_handle * that uses the __free(fwnode_handle) auto
cleanup handling so that if a reference to a node is held on early
exit from the loop the reference will be released. If the loop
runs to completion, the child pointer will be NULL and no action will
be taken.
The reason this is useful is that it removes the need for
fwnode_handle_put() on early loop exits. If there is a need
to retain the reference, then return_ptr(child) or no_free_ptr(child)
may be used to safely disable the auto cleanup.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20240217164249.921878-5-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 73b03b27736e ("leds: flash: mt6360: Fix device_for_each_child_node() refcounting in error paths")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 59ed5e2d505bf5f9b4af64d0021cd0c96aec1f7c ]
Useful where the fwnode_handle was obtained from a call such as
fwnode_find_reference() as it will safely do nothing if IS_ERR() is true
and will automatically release the reference on the variable leaving
scope.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20240217164249.921878-3-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 73b03b27736e ("leds: flash: mt6360: Fix device_for_each_child_node() refcounting in error paths")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7952cd2b8213f20a1752634c25dfd215da537722 ]
The device parameter is not altered in the device child node APIs,
constify them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20221004092129.19412-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 73b03b27736e ("leds: flash: mt6360: Fix device_for_each_child_node() refcounting in error paths")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
