| Age | Commit message (Collapse) | Author |
|---|
|
Correct the misspelling of “estabilished” in the code.
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When the BIS source stops, the controller sends an LE BIG Sync Lost
event (subevent 0x1E). Currently, this event is not handled, causing
the BIS stream to remain active in BlueZ and preventing recovery.
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
HCI_EV_EXTENDED_INQUIRY_RESULT's comment wrongly uses 0x2d as its event
code.
Use right 0x2f instead.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_find_irk_by_addr()
Eliminate an unnecessary goto label by using break instead of goto to
exit the loop in hci_find_irk_by_addr().
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_update_event_filter_sync()
Use bt_dev_err() instead of bt_dev_dbg() to log error message in
hci_update_event_filter_sync().
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Reset cookie value to 0 instead of 0xffffffff in hci_sock_free_cookie()
since:
0 : means cookie has not been assigned yet
0xffffffff: means cookie assignment failure
Also fix generating cookie failure with usage shown below:
hci_sock_gen_cookie(sk) // generate cookie
hci_sock_free_cookie(sk) // free cookie
hci_sock_gen_cookie(sk) // Can't generate cookie any more
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.16-rc7).
Conflicts:
Documentation/netlink/specs/ovpn.yaml
880d43ca9aa4 ("netlink: specs: clean up spaces in brackets")
af52020fc599 ("ovpn: reject unexpected netlink attributes")
drivers/net/phy/phy_device.c
a44312d58e78 ("net: phy: Don't register LEDs for genphy")
f0f2b992d818 ("net: phy: Don't register LEDs for genphy")
https://lore.kernel.org/20250710114926.7ec3a64f@kernel.org
drivers/net/wireless/intel/iwlwifi/fw/regulatory.c
drivers/net/wireless/intel/iwlwifi/mld/regulatory.c
5fde0fcbd760 ("wifi: iwlwifi: mask reserved bits in chan_state_active_bitmap")
ea045a0de3b9 ("wifi: iwlwifi: add support for accepting raw DSM tables by firmware")
net/ipv6/mcast.c
ae3264a25a46 ("ipv6: mcast: Delay put pmc->idev in mld_del_delrec()")
a8594c956cc9 ("ipv6: mcast: Avoid a duplicate pointer check in mld_del_delrec()")
https://lore.kernel.org/8cc52891-3653-4b03-a45e-05464fe495cf@kernel.org
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Configuration request only configure the incoming direction of the peer
initiating the request, so using the MTU is the other direction shall
not be used, that said the spec allows the peer responding to adjust:
Bluetooth Core 6.1, Vol 3, Part A, Section 4.5
'Each configuration parameter value (if any is present) in an
L2CAP_CONFIGURATION_RSP packet reflects an ‘adjustment’ to a
configuration parameter value that has been sent (or, in case of
default values, implied) in the corresponding
L2CAP_CONFIGURATION_REQ packet.'
That said adjusting the MTU in the response shall be limited to ERTM
channels only as for older modes the remote stack may not be able to
detect the adjustment causing it to silently drop packets.
Link: https://github.com/bluez/bluez/issues/1422
Link: https://gitlab.archlinux.org/archlinux/packaging/packages/linux/-/issues/149
Link: https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/4793
Fixes: 042bb9603c44 ("Bluetooth: L2CAP: Fix L2CAP MTU negotiation")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The 'quirks' member already ran out of bits on some platforms some time
ago. Replace the integer member by a bitmap in order to have enough bits
in future. Replace raw bit operations by accessor macros.
Fixes: ff26b2dd6568 ("Bluetooth: Add quirk for broken READ_VOICE_SETTING")
Fixes: 127881334eaa ("Bluetooth: Add quirk for broken READ_PAGE_SCAN_TYPE")
Suggested-by: Pauli Virtanen <pav@iki.fi>
Tested-by: Ivan Pravdin <ipravdin.official@gmail.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This replaces the usage of HCI_ERROR_REMOTE_USER_TERM, which as the name
suggest is to indicate a regular disconnection initiated by an user,
with HCI_ERROR_AUTH_FAILURE to indicate the session has timeout thus any
pairing shall be considered as failed.
Fixes: 1e91c29eb60c ("Bluetooth: Use hci_disconnect for immediate disconnection from SMP")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If a command is received while a bonding is ongoing consider it a
pairing failure so the session is cleanup properly and the device is
disconnected immediately instead of continuing with other commands that
may result in the session to get stuck without ever completing such as
the case bellow:
> ACL Data RX: Handle 2048 flags 0x02 dlen 21
SMP: Identity Information (0x08) len 16
Identity resolving key[16]: d7e08edef97d3e62cd2331f82d8073b0
> ACL Data RX: Handle 2048 flags 0x02 dlen 21
SMP: Signing Information (0x0a) len 16
Signature key[16]: 1716c536f94e843a9aea8b13ffde477d
Bluetooth: hci0: unexpected SMP command 0x0a from XX:XX:XX:XX:XX:XX
> ACL Data RX: Handle 2048 flags 0x02 dlen 12
SMP: Identity Address Information (0x09) len 7
Address: XX:XX:XX:XX:XX:XX (Intel Corporate)
While accourding to core spec 6.1 the expected order is always BD_ADDR
first first then CSRK:
When using LE legacy pairing, the keys shall be distributed in the
following order:
LTK by the Peripheral
EDIV and Rand by the Peripheral
IRK by the Peripheral
BD_ADDR by the Peripheral
CSRK by the Peripheral
LTK by the Central
EDIV and Rand by the Central
IRK by the Central
BD_ADDR by the Central
CSRK by the Central
When using LE Secure Connections, the keys shall be distributed in the
following order:
IRK by the Peripheral
BD_ADDR by the Peripheral
CSRK by the Peripheral
IRK by the Central
BD_ADDR by the Central
CSRK by the Central
According to the Core 6.1 for commands used for key distribution "Key
Rejected" can be used:
'3.6.1. Key distribution and generation
A device may reject a distributed key by sending the Pairing Failed command
with the reason set to "Key Rejected".
Fixes: b28b4943660f ("Bluetooth: Add strict checks for allowed SMP PDUs")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
random address
Currently, the connectable flag used by the setup of an extended
advertising instance drives whether we require privacy when trying to pass
a random address to the advertising parameters (Own Address).
If privacy is not required, then it automatically falls back to using the
controller's public address. This can cause problems when using controllers
that do not have a public address set, but instead use a static random
address.
e.g. Assume a BLE controller that does not have a public address set.
The controller upon powering is set with a random static address by default
by the kernel.
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6
Address: E4:AF:26:D8:3E:3A (Static)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
Setting non-connectable extended advertisement parameters in bluetoothctl
mgmt
add-ext-adv-params -r 0x801 -x 0x802 -P 2M -g 1
correctly sets Own address type as Random
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036)
plen 25
...
Own address type: Random (0x01)
Setting connectable extended advertisement parameters in bluetoothctl mgmt
add-ext-adv-params -r 0x801 -x 0x802 -P 2M -g -c 1
mistakenly sets Own address type to Public (which causes to use Public
Address 00:00:00:00:00:00)
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036)
plen 25
...
Own address type: Public (0x00)
This causes either the controller to emit an Invalid Parameters error or to
mishandle the advertising.
This patch makes sure that we use the already set static random address
when requesting a connectable extended advertising when we don't require
privacy and our public address is not set (00:00:00:00:00:00).
Fixes: 3fe318ee72c5 ("Bluetooth: move hci_get_random_address() to hci_sync")
Signed-off-by: Alessandro Gasbarroni <alex.gasbarroni@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
syzbot reported null-ptr-deref in l2cap_sock_resume_cb(). [0]
l2cap_sock_resume_cb() has a similar problem that was fixed by commit
1bff51ea59a9 ("Bluetooth: fix use-after-free error in lock_sock_nested()").
Since both l2cap_sock_kill() and l2cap_sock_resume_cb() are executed
under l2cap_sock_resume_cb(), we can avoid the issue simply by checking
if chan->data is NULL.
Let's not access to the killed socket in l2cap_sock_resume_cb().
[0]:
BUG: KASAN: null-ptr-deref in instrument_atomic_write include/linux/instrumented.h:82 [inline]
BUG: KASAN: null-ptr-deref in clear_bit include/asm-generic/bitops/instrumented-atomic.h:41 [inline]
BUG: KASAN: null-ptr-deref in l2cap_sock_resume_cb+0xb4/0x17c net/bluetooth/l2cap_sock.c:1711
Write of size 8 at addr 0000000000000570 by task kworker/u9:0/52
CPU: 1 UID: 0 PID: 52 Comm: kworker/u9:0 Not tainted 6.16.0-rc4-syzkaller-g7482bb149b9f #0 PREEMPT
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025
Workqueue: hci0 hci_rx_work
Call trace:
show_stack+0x2c/0x3c arch/arm64/kernel/stacktrace.c:501 (C)
__dump_stack+0x30/0x40 lib/dump_stack.c:94
dump_stack_lvl+0xd8/0x12c lib/dump_stack.c:120
print_report+0x58/0x84 mm/kasan/report.c:524
kasan_report+0xb0/0x110 mm/kasan/report.c:634
check_region_inline mm/kasan/generic.c:-1 [inline]
kasan_check_range+0x264/0x2a4 mm/kasan/generic.c:189
__kasan_check_write+0x20/0x30 mm/kasan/shadow.c:37
instrument_atomic_write include/linux/instrumented.h:82 [inline]
clear_bit include/asm-generic/bitops/instrumented-atomic.h:41 [inline]
l2cap_sock_resume_cb+0xb4/0x17c net/bluetooth/l2cap_sock.c:1711
l2cap_security_cfm+0x524/0xea0 net/bluetooth/l2cap_core.c:7357
hci_auth_cfm include/net/bluetooth/hci_core.h:2092 [inline]
hci_auth_complete_evt+0x2e8/0xa4c net/bluetooth/hci_event.c:3514
hci_event_func net/bluetooth/hci_event.c:7511 [inline]
hci_event_packet+0x650/0xe9c net/bluetooth/hci_event.c:7565
hci_rx_work+0x320/0xb18 net/bluetooth/hci_core.c:4070
process_one_work+0x7e8/0x155c kernel/workqueue.c:3238
process_scheduled_works kernel/workqueue.c:3321 [inline]
worker_thread+0x958/0xed8 kernel/workqueue.c:3402
kthread+0x5fc/0x75c kernel/kthread.c:464
ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:847
Fixes: d97c899bde33 ("Bluetooth: Introduce L2CAP channel callback for resuming")
Reported-by: syzbot+e4d73b165c3892852d22@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/686c12bd.a70a0220.29fe6c.0b13.GAE@google.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.16-rc6).
No conflicts.
Adjacent changes:
Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml
0a12c435a1d6 ("dt-bindings: net: sun8i-emac: Add A100 EMAC compatible")
b3603c0466a8 ("dt-bindings: net: sun8i-emac: Rename A523 EMAC0 to GMAC0")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.16-rc5).
No conflicts.
No adjacent changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Upon receiving HCI_EVT_LE_BIG_SYNC_ESTABLISHED with status 0x00
(success) the corresponding BIS hci_conn state shall be set to
BT_CONNECTED otherwise they will be left with BT_OPEN which is invalid
at that point, also create the debugfs and sysfs entries following the
same logic as the likes of Broadcast Source BIS and CIS connections.
Fixes: f777d8827817 ("Bluetooth: ISO: Notify user space about failed bis connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
BIS/PA connections do have their own cleanup proceedure which are
performed by hci_conn_cleanup/bis_cleanup.
Fixes: 23205562ffc8 ("Bluetooth: separate CIS_LINK and BIS_LINK link types")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
As the code comments on hci_setup_ext_adv_instance_sync suggests the
advertising instance needs to be disabled in order to update its
parameters, but it was wrongly checking that !adv->pending.
Fixes: cba6b758711c ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, for controllers with extended advertising, the advertising
data is set in the asynchronous response handler for extended
adverstising params. As most advertising settings are performed in a
synchronous context, the (asynchronous) setting of the advertising data
is done too late (after enabling the advertising).
Move setting of adverstising data from asynchronous response handler
into synchronous context to fix ordering of HCI commands.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: a0fb3726ba55 ("Bluetooth: Use Set ext adv/scan rsp data if controller supports")
Cc: stable@vger.kernel.org
v2: https://lore.kernel.org/linux-bluetooth/20250626115209.17839-1-ceggers@arri.de/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The unconditional call of hci_disable_advertising_sync() in
mesh_send_done_sync() also disables other LE advertisings (non mesh
related).
I am not sure whether this call is required at all, but checking the
adv_instances list (like done at other places) seems to solve the
problem.
Fixes: b338d91703fa ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
According to the message of commit b338d91703fa ("Bluetooth: Implement
support for Mesh"), MGMT_OP_SET_MESH_RECEIVER should set the passive scan
parameters. Currently the scan interval and window parameters are
silently ignored, although user space (bluetooth-meshd) expects that
they can be used [1]
[1] https://git.kernel.org/pub/scm/bluetooth/bluez.git/tree/mesh/mesh-io-mgmt.c#n344
Fixes: b338d91703fa ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This reverts minor parts of the changes made in commit b338d91703fa
("Bluetooth: Implement support for Mesh"). It looks like these changes
were only made for development purposes but shouldn't have been part of
the commit.
Fixes: b338d91703fa ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When PA Create Sync is enabled, advertising resumes unexpectedly.
Therefore, it's necessary to check whether advertising is currently
active before attempting to pause it.
< HCI Command: LE Add Device To... (0x08|0x0011) plen 7 #1345 [hci0] 48.306205
Address type: Random (0x01)
Address: 4F:84:84:5F:88:17 (Resolvable)
Identity type: Random (0x01)
Identity: FC:5B:8C:F7:5D:FB (Static)
< HCI Command: LE Set Address Re.. (0x08|0x002d) plen 1 #1347 [hci0] 48.308023
Address resolution: Enabled (0x01)
...
< HCI Command: LE Set Extended A.. (0x08|0x0039) plen 6 #1349 [hci0] 48.309650
Extended advertising: Enabled (0x01)
Number of sets: 1 (0x01)
Entry 0
Handle: 0x01
Duration: 0 ms (0x00)
Max ext adv events: 0
...
< HCI Command: LE Periodic Adve.. (0x08|0x0044) plen 14 #1355 [hci0] 48.314575
Options: 0x0000
Use advertising SID, Advertiser Address Type and address
Reporting initially enabled
SID: 0x02
Adv address type: Random (0x01)
Adv address: 4F:84:84:5F:88:17 (Resolvable)
Identity type: Random (0x01)
Identity: FC:5B:8C:F7:5D:FB (Static)
Skip: 0x0000
Sync timeout: 20000 msec (0x07d0)
Sync CTE type: 0x0000
Fixes: ad383c2c65a5 ("Bluetooth: hci_sync: Enable advertising when LL privacy is enabled")
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.16-rc4).
Conflicts:
Documentation/netlink/specs/mptcp_pm.yaml
9e6dd4c256d0 ("netlink: specs: mptcp: replace underscores with dashes in names")
ec362192aa9e ("netlink: specs: fix up indentation errors")
https://lore.kernel.org/20250626122205.389c2cd4@canb.auug.org.au
Adjacent changes:
Documentation/netlink/specs/fou.yaml
791a9ed0a40d ("netlink: specs: fou: replace underscores with dashes in names")
880d43ca9aa4 ("netlink: specs: clean up spaces in brackets")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Followup of commit 285975dd6742 ("net: annotate data-races around
sk->sk_{rcv|snd}timeo").
Remove lock_sock()/release_sock() from sock_set_sndtimeo(),
and add READ_ONCE()/WRITE_ONCE() where it is needed.
Also SO_SNDTIMEO_OLD and SO_SNDTIMEO_NEW can call sock_set_timeout()
without holding the socket lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250620155536.335520-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Difference between sock_i_uid() and sk_uid() is that
after sock_orphan(), sock_i_uid() returns GLOBAL_ROOT_UID
while sk_uid() returns the last cached sk->sk_uid value.
None of sock_i_uid() callers care about this.
Use sk_uid() which is much faster and inlined.
Note that diag/dump users are calling sock_i_ino() and
can not see the full benefit yet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://patch.msgid.link/20250620133001.4090592-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reported use-after-free in vhci_flush() without repro. [0]
From the splat, a thread close()d a vhci file descriptor while
its device was being used by iotcl() on another thread.
Once the last fd refcnt is released, vhci_release() calls
hci_unregister_dev(), hci_free_dev(), and kfree() for struct
vhci_data, which is set to hci_dev->dev->driver_data.
The problem is that there is no synchronisation after unlinking
hdev from hci_dev_list in hci_unregister_dev(). There might be
another thread still accessing the hdev which was fetched before
the unlink operation.
We can use SRCU for such synchronisation.
Let's run hci_dev_reset() under SRCU and wait for its completion
in hci_unregister_dev().
Another option would be to restore hci_dev->destruct(), which was
removed in commit 587ae086f6e4 ("Bluetooth: Remove unused
hci-destruct cb"). However, this would not be a good solution, as
we should not run hci_unregister_dev() while there are in-flight
ioctl() requests, which could lead to another data-race KCSAN splat.
Note that other drivers seem to have the same problem, for exmaple,
virtbt_remove().
[0]:
BUG: KASAN: slab-use-after-free in skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
BUG: KASAN: slab-use-after-free in skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
Read of size 8 at addr ffff88807cb8d858 by task syz.1.219/6718
CPU: 1 UID: 0 PID: 6718 Comm: syz.1.219 Not tainted 6.16.0-rc1-syzkaller-00196-g08207f42d3ff #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025
Call Trace:
<TASK>
dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:408 [inline]
print_report+0xd2/0x2b0 mm/kasan/report.c:521
kasan_report+0x118/0x150 mm/kasan/report.c:634
skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
skb_queue_purge include/linux/skbuff.h:3368 [inline]
vhci_flush+0x44/0x50 drivers/bluetooth/hci_vhci.c:69
hci_dev_do_reset net/bluetooth/hci_core.c:552 [inline]
hci_dev_reset+0x420/0x5c0 net/bluetooth/hci_core.c:592
sock_do_ioctl+0xd9/0x300 net/socket.c:1190
sock_ioctl+0x576/0x790 net/socket.c:1311
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xf9/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fcf5b98e929
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fcf5c7b9038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fcf5bbb6160 RCX: 00007fcf5b98e929
RDX: 0000000000000000 RSI: 00000000400448cb RDI: 0000000000000009
RBP: 00007fcf5ba10b39 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 00007fcf5bbb6160 R15: 00007ffd6353d528
</TASK>
Allocated by task 6535:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
poison_kmalloc_redzone mm/kasan/common.c:377 [inline]
__kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:394
kasan_kmalloc include/linux/kasan.h:260 [inline]
__kmalloc_cache_noprof+0x230/0x3d0 mm/slub.c:4359
kmalloc_noprof include/linux/slab.h:905 [inline]
kzalloc_noprof include/linux/slab.h:1039 [inline]
vhci_open+0x57/0x360 drivers/bluetooth/hci_vhci.c:635
misc_open+0x2bc/0x330 drivers/char/misc.c:161
chrdev_open+0x4c9/0x5e0 fs/char_dev.c:414
do_dentry_open+0xdf0/0x1970 fs/open.c:964
vfs_open+0x3b/0x340 fs/open.c:1094
do_open fs/namei.c:3887 [inline]
path_openat+0x2ee5/0x3830 fs/namei.c:4046
do_filp_open+0x1fa/0x410 fs/namei.c:4073
do_sys_openat2+0x121/0x1c0 fs/open.c:1437
do_sys_open fs/open.c:1452 [inline]
__do_sys_openat fs/open.c:1468 [inline]
__se_sys_openat fs/open.c:1463 [inline]
__x64_sys_openat+0x138/0x170 fs/open.c:1463
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 6535:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
kasan_save_free_info+0x46/0x50 mm/kasan/generic.c:576
poison_slab_object mm/kasan/common.c:247 [inline]
__kasan_slab_free+0x62/0x70 mm/kasan/common.c:264
kasan_slab_free include/linux/kasan.h:233 [inline]
slab_free_hook mm/slub.c:2381 [inline]
slab_free mm/slub.c:4643 [inline]
kfree+0x18e/0x440 mm/slub.c:4842
vhci_release+0xbc/0xd0 drivers/bluetooth/hci_vhci.c:671
__fput+0x44c/0xa70 fs/file_table.c:465
task_work_run+0x1d1/0x260 kernel/task_work.c:227
exit_task_work include/linux/task_work.h:40 [inline]
do_exit+0x6ad/0x22e0 kernel/exit.c:955
do_group_exit+0x21c/0x2d0 kernel/exit.c:1104
__do_sys_exit_group kernel/exit.c:1115 [inline]
__se_sys_exit_group kernel/exit.c:1113 [inline]
__x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1113
x64_sys_call+0x21ba/0x21c0 arch/x86/include/generated/asm/syscalls_64.h:232
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The buggy address belongs to the object at ffff88807cb8d800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 88 bytes inside of
freed 1024-byte region [ffff88807cb8d800, ffff88807cb8dc00)
Fixes: bf18c7118cf8 ("Bluetooth: vhci: Free driver_data on file release")
Reported-by: syzbot+2faa4825e556199361f9@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=f62d64848fc4c7c30cd6
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
OBEX download from iPhone is currently slow due to small packet size
used to transfer data which doesn't follow the MTU negotiated during
L2CAP connection, i.e. 672 bytes instead of 32767:
< ACL Data TX: Handle 11 flags 0x00 dlen 12
L2CAP: Connection Request (0x02) ident 18 len 4
PSM: 4103 (0x1007)
Source CID: 72
> ACL Data RX: Handle 11 flags 0x02 dlen 16
L2CAP: Connection Response (0x03) ident 18 len 8
Destination CID: 14608
Source CID: 72
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 11 flags 0x00 dlen 27
L2CAP: Configure Request (0x04) ident 20 len 19
Destination CID: 14608
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 63
Max transmit: 3
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
> ACL Data RX: Handle 11 flags 0x02 dlen 26
L2CAP: Configure Request (0x04) ident 72 len 18
Destination CID: 72
Flags: 0x0000
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 32
Max transmit: 255
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 65527
Option: Frame Check Sequence (0x05) [mandatory]
FCS: 16-bit FCS (0x01)
< ACL Data TX: Handle 11 flags 0x00 dlen 29
L2CAP: Configure Response (0x05) ident 72 len 21
Source CID: 14608
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 672
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 32
Max transmit: 255
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
> ACL Data RX: Handle 11 flags 0x02 dlen 32
L2CAP: Configure Response (0x05) ident 20 len 24
Source CID: 72
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 63
Max transmit: 3
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
Option: Frame Check Sequence (0x05) [mandatory]
FCS: 16-bit FCS (0x01)
...
> ACL Data RX: Handle 11 flags 0x02 dlen 680
Channel: 72 len 676 ctrl 0x0202 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Unsegmented TxSeq 1 ReqSeq 2
< ACL Data TX: Handle 11 flags 0x00 dlen 13
Channel: 14608 len 9 ctrl 0x0204 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Unsegmented TxSeq 2 ReqSeq 2
> ACL Data RX: Handle 11 flags 0x02 dlen 680
Channel: 72 len 676 ctrl 0x0304 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Unsegmented TxSeq 2 ReqSeq 3
The MTUs are negotiated for each direction. In this traces 32767 for
iPhone->localhost and no MTU for localhost->iPhone, which based on
'4.4 L2CAP_CONFIGURATION_REQ' (Core specification v5.4, Vol. 3, Part
A):
The only parameters that should be included in the
L2CAP_CONFIGURATION_REQ packet are those that require different
values than the default or previously agreed values.
...
Any missing configuration parameters are assumed to have their
most recently explicitly or implicitly accepted values.
and '5.1 Maximum transmission unit (MTU)':
If the remote device sends a positive L2CAP_CONFIGURATION_RSP
packet it should include the actual MTU to be used on this channel
for traffic flowing into the local device.
...
The default value is 672 octets.
is set by BlueZ to 672 bytes.
It seems that the iPhone used the lowest negotiated value to transfer
data to the localhost instead of the negotiated one for the incoming
direction.
This could be fixed by using the MTU negotiated for the other
direction, if exists, in the L2CAP_CONFIGURATION_RSP.
This allows to use segmented packets as in the following traces:
< ACL Data TX: Handle 11 flags 0x00 dlen 12
L2CAP: Connection Request (0x02) ident 22 len 4
PSM: 4103 (0x1007)
Source CID: 72
< ACL Data TX: Handle 11 flags 0x00 dlen 27
L2CAP: Configure Request (0x04) ident 24 len 19
Destination CID: 2832
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 63
Max transmit: 3
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
> ACL Data RX: Handle 11 flags 0x02 dlen 26
L2CAP: Configure Request (0x04) ident 15 len 18
Destination CID: 72
Flags: 0x0000
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 32
Max transmit: 255
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 65527
Option: Frame Check Sequence (0x05) [mandatory]
FCS: 16-bit FCS (0x01)
< ACL Data TX: Handle 11 flags 0x00 dlen 29
L2CAP: Configure Response (0x05) ident 15 len 21
Source CID: 2832
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 32
Max transmit: 255
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
> ACL Data RX: Handle 11 flags 0x02 dlen 32
L2CAP: Configure Response (0x05) ident 24 len 24
Source CID: 72
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 63
Max transmit: 3
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
Option: Frame Check Sequence (0x05) [mandatory]
FCS: 16-bit FCS (0x01)
...
> ACL Data RX: Handle 11 flags 0x02 dlen 1009
Channel: 72 len 1005 ctrl 0x4202 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Start (len 21884) TxSeq 1 ReqSeq 2
> ACL Data RX: Handle 11 flags 0x02 dlen 1009
Channel: 72 len 1005 ctrl 0xc204 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Continuation TxSeq 2 ReqSeq 2
This has been tested with kernel 5.4 and BlueZ 5.77.
Cc: stable@vger.kernel.org
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This code (tty_get -> vhangup -> tty_put) is repeated on few places.
Introduce a helper similar to tty_port_tty_hangup() (asynchronous) to
handle even vhangup (synchronous).
And use it on those places.
In fact, reuse the tty_port_tty_hangup()'s code and call tty_vhangup()
depending on a new bool parameter.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth and wireless.
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent
invalid routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused
transient packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple
requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set"
* tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
selftests: drv-net: rss_ctx: Add test for ntuple rules targeting default RSS context
net: ethtool: Don't check if RSS context exists in case of context 0
af_unix: Allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD.
ipv6: Move fib6_config_validate() to ip6_route_add().
net: drv: netdevsim: don't napi_complete() from netpoll
net/mlx5: HWS, Add error checking to hws_bwc_rule_complex_hash_node_get()
veth: prevent NULL pointer dereference in veth_xdp_rcv
net_sched: remove qdisc_tree_flush_backlog()
net_sched: ets: fix a race in ets_qdisc_change()
net_sched: tbf: fix a race in tbf_change()
net_sched: red: fix a race in __red_change()
net_sched: prio: fix a race in prio_tune()
net_sched: sch_sfq: reject invalid perturb period
net: phy: phy_caps: Don't skip better duplex macth on non-exact match
MAINTAINERS: Update Kuniyuki Iwashima's email address.
selftests: net: add test case for NAT46 looping back dst
net: clear the dst when changing skb protocol
net/mlx5e: Fix number of lanes to UNKNOWN when using data_rate_oper
net/mlx5e: Fix leak of Geneve TLV option object
net/mlx5: HWS, make sure the uplink is the last destination
...
|
|
This fixes the following errors:
net/bluetooth/mgmt.c:5400:59: sparse: sparse: incorrect type in argument 3
(different base types) @@ expected unsigned short [usertype] handle @@
got restricted __le16 [usertype] monitor_handle @@
net/bluetooth/mgmt.c:5400:59: sparse: expected unsigned short [usertype] handle
net/bluetooth/mgmt.c:5400:59: sparse: got restricted __le16 [usertype] monitor_handle
Fixes: e6ed54e86aae ("Bluetooth: MGMT: Fix UAF on mgmt_remove_adv_monitor_complete")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202506060347.ux2O1p7L-lkp@intel.com/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Currently bc_sid is being ignore when acting as Broadcast Source role,
so this fix it by passing the bc_sid and then use it when programming
the PA:
< HCI Command: LE Set Exte.. (0x08|0x0036) plen 25
Handle: 0x01
Properties: 0x0000
Min advertising interval: 140.000 msec (0x00e0)
Max advertising interval: 140.000 msec (0x00e0)
Channel map: 37, 38, 39 (0x07)
Own address type: Random (0x01)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
TX power: Host has no preference (0x7f)
Primary PHY: LE 1M (0x01)
Secondary max skip: 0x00
Secondary PHY: LE 2M (0x02)
SID: 0x01
Scan request notifications: Disabled (0x00)
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
BT_SK_PA_SYNC is only valid for Broadcast Sinks which means socket used
for Broadcast Sources wouldn't be able to use the likes of getpeername
to read out the sockaddr_iso_bc fields which may have been update (e.g.
bc_sid).
Fixes: 0a766a0affb5 ("Bluetooth: ISO: Fix getpeername not returning sockaddr_iso_bc fields")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
eir_create_adv_data may attempt to add EIR_FLAGS and EIR_TX_POWER
without checking if that would fit.
Link: https://github.com/bluez/bluez/issues/1117#issuecomment-2958244066
Fixes: 01ce70b0a274 ("Bluetooth: eir: Move EIR/Adv Data functions to its own file")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When using and existing adv_info instance for broadcast source it
needs to be updated to periodic first before it can be reused, also in
case the existing instance already have data hci_set_adv_instance_data
cannot be used directly since it would overwrite the existing data so
this reappend the original data after the Broadcast ID, if one was
generated.
Example:
bluetoothctl># Add PBP to EA so it can be later referenced as the BIS ID
bluetoothctl> advertise.service 0x1856 0x00 0x00
bluetoothctl> advertise on
...
< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 13
Handle: 0x01
Operation: Complete extended advertising data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x09
Service Data: Public Broadcast Announcement (0x1856)
Data[2]: 0000
Flags: 0x06
LE General Discoverable Mode
BR/EDR Not Supported
...
bluetoothctl># Attempt to acquire Broadcast Source transport
bluetoothctl>transport.acquire /org/bluez/hci0/pac_bcast0/fd0
...
< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 255
Handle: 0x01
Operation: Complete extended advertising data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x0e
Service Data: Broadcast Audio Announcement (0x1852)
Broadcast ID: 11371620 (0xad8464)
Service Data: Public Broadcast Announcement (0x1856)
Data[2]: 0000
Flags: 0x06
LE General Discoverable Mode
BR/EDR Not Supported
Link: https://github.com/bluez/bluez/issues/1117
Fixes: eca0ae4aea66 ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The len parameter is considered optional so it can be NULL so it cannot
be used for skipping to next entry of EIR_SERVICE_DATA.
Fixes: 8f9ae5b3ae80 ("Bluetooth: eir: Add helpers for managing service data")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
|
|
This uses a mutex to protect from concurrent access of mgmt_pending
list which can cause crashes like:
==================================================================
BUG: KASAN: slab-use-after-free in hci_sock_get_channel+0x60/0x68 net/bluetooth/hci_sock.c:91
Read of size 2 at addr ffff0000c48885b2 by task syz.4.334/7318
CPU: 0 UID: 0 PID: 7318 Comm: syz.4.334 Not tainted 6.15.0-rc7-syzkaller-g187899f4124a #0 PREEMPT
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025
Call trace:
show_stack+0x2c/0x3c arch/arm64/kernel/stacktrace.c:466 (C)
__dump_stack+0x30/0x40 lib/dump_stack.c:94
dump_stack_lvl+0xd8/0x12c lib/dump_stack.c:120
print_address_description+0xa8/0x254 mm/kasan/report.c:408
print_report+0x68/0x84 mm/kasan/report.c:521
kasan_report+0xb0/0x110 mm/kasan/report.c:634
__asan_report_load2_noabort+0x20/0x2c mm/kasan/report_generic.c:379
hci_sock_get_channel+0x60/0x68 net/bluetooth/hci_sock.c:91
mgmt_pending_find+0x7c/0x140 net/bluetooth/mgmt_util.c:223
pending_find net/bluetooth/mgmt.c:947 [inline]
remove_adv_monitor+0x44/0x1a4 net/bluetooth/mgmt.c:5445
hci_mgmt_cmd+0x780/0xc00 net/bluetooth/hci_sock.c:1712
hci_sock_sendmsg+0x544/0xbb0 net/bluetooth/hci_sock.c:1832
sock_sendmsg_nosec net/socket.c:712 [inline]
__sock_sendmsg net/socket.c:727 [inline]
sock_write_iter+0x25c/0x378 net/socket.c:1131
new_sync_write fs/read_write.c:591 [inline]
vfs_write+0x62c/0x97c fs/read_write.c:684
ksys_write+0x120/0x210 fs/read_write.c:736
__do_sys_write fs/read_write.c:747 [inline]
__se_sys_write fs/read_write.c:744 [inline]
__arm64_sys_write+0x7c/0x90 fs/read_write.c:744
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:49
el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:132
do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:151
el0_svc+0x58/0x17c arch/arm64/kernel/entry-common.c:767
el0t_64_sync_handler+0x78/0x108 arch/arm64/kernel/entry-common.c:786
el0t_64_sync+0x198/0x19c arch/arm64/kernel/entry.S:600
Allocated by task 7037:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x40/0x78 mm/kasan/common.c:68
kasan_save_alloc_info+0x44/0x54 mm/kasan/generic.c:562
poison_kmalloc_redzone mm/kasan/common.c:377 [inline]
__kasan_kmalloc+0x9c/0xb4 mm/kasan/common.c:394
kasan_kmalloc include/linux/kasan.h:260 [inline]
__do_kmalloc_node mm/slub.c:4327 [inline]
__kmalloc_noprof+0x2fc/0x4c8 mm/slub.c:4339
kmalloc_noprof include/linux/slab.h:909 [inline]
sk_prot_alloc+0xc4/0x1f0 net/core/sock.c:2198
sk_alloc+0x44/0x3ac net/core/sock.c:2254
bt_sock_alloc+0x4c/0x300 net/bluetooth/af_bluetooth.c:148
hci_sock_create+0xa8/0x194 net/bluetooth/hci_sock.c:2202
bt_sock_create+0x14c/0x24c net/bluetooth/af_bluetooth.c:132
__sock_create+0x43c/0x91c net/socket.c:1541
sock_create net/socket.c:1599 [inline]
__sys_socket_create net/socket.c:1636 [inline]
__sys_socket+0xd4/0x1c0 net/socket.c:1683
__do_sys_socket net/socket.c:1697 [inline]
__se_sys_socket net/socket.c:1695 [inline]
__arm64_sys_socket+0x7c/0x94 net/socket.c:1695
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:49
el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:132
do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:151
el0_svc+0x58/0x17c arch/arm64/kernel/entry-common.c:767
el0t_64_sync_handler+0x78/0x108 arch/arm64/kernel/entry-common.c:786
el0t_64_sync+0x198/0x19c arch/arm64/kernel/entry.S:600
Freed by task 6607:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x40/0x78 mm/kasan/common.c:68
kasan_save_free_info+0x58/0x70 mm/kasan/generic.c:576
poison_slab_object mm/kasan/common.c:247 [inline]
__kasan_slab_free+0x68/0x88 mm/kasan/common.c:264
kasan_slab_free include/linux/kasan.h:233 [inline]
slab_free_hook mm/slub.c:2380 [inline]
slab_free mm/slub.c:4642 [inline]
kfree+0x17c/0x474 mm/slub.c:4841
sk_prot_free net/core/sock.c:2237 [inline]
__sk_destruct+0x4f4/0x760 net/core/sock.c:2332
sk_destruct net/core/sock.c:2360 [inline]
__sk_free+0x320/0x430 net/core/sock.c:2371
sk_free+0x60/0xc8 net/core/sock.c:2382
sock_put include/net/sock.h:1944 [inline]
mgmt_pending_free+0x88/0x118 net/bluetooth/mgmt_util.c:290
mgmt_pending_remove+0xec/0x104 net/bluetooth/mgmt_util.c:298
mgmt_set_powered_complete+0x418/0x5cc net/bluetooth/mgmt.c:1355
hci_cmd_sync_work+0x204/0x33c net/bluetooth/hci_sync.c:334
process_one_work+0x7e8/0x156c kernel/workqueue.c:3238
process_scheduled_works kernel/workqueue.c:3319 [inline]
worker_thread+0x958/0xed8 kernel/workqueue.c:3400
kthread+0x5fc/0x75c kernel/kthread.c:464
ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:847
Fixes: a380b6cff1a2 ("Bluetooth: Add generic mgmt helper API")
Closes: https://syzkaller.appspot.com/bug?extid=0a7039d5d9986ff4ecec
Closes: https://syzkaller.appspot.com/bug?extid=cc0cc52e7f43dc9e6df1
Reported-by: syzbot+0a7039d5d9986ff4ecec@syzkaller.appspotmail.com
Tested-by: syzbot+0a7039d5d9986ff4ecec@syzkaller.appspotmail.com
Tested-by: syzbot+cc0cc52e7f43dc9e6df1@syzkaller.appspotmail.com
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This reworks MGMT_OP_REMOVE_ADV_MONITOR to not use mgmt_pending_add to
avoid crashes like bellow:
==================================================================
BUG: KASAN: slab-use-after-free in mgmt_remove_adv_monitor_complete+0xe5/0x540 net/bluetooth/mgmt.c:5406
Read of size 8 at addr ffff88801c53f318 by task kworker/u5:5/5341
CPU: 0 UID: 0 PID: 5341 Comm: kworker/u5:5 Not tainted 6.15.0-syzkaller-10402-g4cb6c8af8591 #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
<TASK>
dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:408 [inline]
print_report+0xd2/0x2b0 mm/kasan/report.c:521
kasan_report+0x118/0x150 mm/kasan/report.c:634
mgmt_remove_adv_monitor_complete+0xe5/0x540 net/bluetooth/mgmt.c:5406
hci_cmd_sync_work+0x261/0x3a0 net/bluetooth/hci_sync.c:334
process_one_work kernel/workqueue.c:3238 [inline]
process_scheduled_works+0xade/0x17b0 kernel/workqueue.c:3321
worker_thread+0x8a0/0xda0 kernel/workqueue.c:3402
kthread+0x711/0x8a0 kernel/kthread.c:464
ret_from_fork+0x3fc/0x770 arch/x86/kernel/process.c:148
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
Allocated by task 5987:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
poison_kmalloc_redzone mm/kasan/common.c:377 [inline]
__kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:394
kasan_kmalloc include/linux/kasan.h:260 [inline]
__kmalloc_cache_noprof+0x230/0x3d0 mm/slub.c:4358
kmalloc_noprof include/linux/slab.h:905 [inline]
kzalloc_noprof include/linux/slab.h:1039 [inline]
mgmt_pending_new+0x65/0x240 net/bluetooth/mgmt_util.c:252
mgmt_pending_add+0x34/0x120 net/bluetooth/mgmt_util.c:279
remove_adv_monitor+0x103/0x1b0 net/bluetooth/mgmt.c:5454
hci_mgmt_cmd+0x9c9/0xef0 net/bluetooth/hci_sock.c:1719
hci_sock_sendmsg+0x6ca/0xef0 net/bluetooth/hci_sock.c:1839
sock_sendmsg_nosec net/socket.c:712 [inline]
__sock_sendmsg+0x219/0x270 net/socket.c:727
sock_write_iter+0x258/0x330 net/socket.c:1131
new_sync_write fs/read_write.c:593 [inline]
vfs_write+0x548/0xa90 fs/read_write.c:686
ksys_write+0x145/0x250 fs/read_write.c:738
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 5989:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
kasan_save_free_info+0x46/0x50 mm/kasan/generic.c:576
poison_slab_object mm/kasan/common.c:247 [inline]
__kasan_slab_free+0x62/0x70 mm/kasan/common.c:264
kasan_slab_free include/linux/kasan.h:233 [inline]
slab_free_hook mm/slub.c:2380 [inline]
slab_free mm/slub.c:4642 [inline]
kfree+0x18e/0x440 mm/slub.c:4841
mgmt_pending_foreach+0xc9/0x120 net/bluetooth/mgmt_util.c:242
mgmt_index_removed+0x10d/0x2f0 net/bluetooth/mgmt.c:9366
hci_sock_bind+0xbe9/0x1000 net/bluetooth/hci_sock.c:1314
__sys_bind_socket net/socket.c:1810 [inline]
__sys_bind+0x2c3/0x3e0 net/socket.c:1841
__do_sys_bind net/socket.c:1846 [inline]
__se_sys_bind net/socket.c:1844 [inline]
__x64_sys_bind+0x7a/0x90 net/socket.c:1844
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: 66bd095ab5d4 ("Bluetooth: advmon offload MSFT remove monitor")
Closes: https://syzkaller.appspot.com/bug?extid=feb0dc579bbe30a13190
Reported-by: syzbot+feb0dc579bbe30a13190@syzkaller.appspotmail.com
Tested-by: syzbot+feb0dc579bbe30a13190@syzkaller.appspotmail.com
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Releasing + re-acquiring RCU lock inside list_for_each_entry_rcu() loop
body is not correct.
Fix by taking the update-side hdev->lock instead.
Fixes: c7eaf80bfb0c ("Bluetooth: Fix hci_link_tx_to RCU lock usage")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Depending on the security set the response to L2CAP_LE_CONN_REQ shall be
just L2CAP_CR_LE_ENCRYPTION if only encryption when BT_SECURITY_MEDIUM
is selected since that means security mode 2 which doesn't require
authentication which is something that is covered in the qualification
test L2CAP/LE/CFC/BV-25-C.
Link: https://github.com/bluez/bluez/issues/1270
Fixes: 27e2d4c8d28b ("Bluetooth: Add basic LE L2CAP connect request receiving support")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In 'mgmt_hci_cmd_sync()', check whether the size of parameters passed
in 'struct mgmt_cp_hci_cmd_sync' matches the total size of the data
(i.e. 'sizeof(struct mgmt_cp_hci_cmd_sync)' plus trailing bytes).
Otherwise, large invalid 'params_len' will cause 'hci_cmd_sync_alloc()'
to do 'skb_put_data()' from an area beyond the one actually passed to
'mgmt_hci_cmd_sync()'.
Reported-by: syzbot+5fe2d5bfbfbec0b675a0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=5fe2d5bfbfbec0b675a0
Fixes: 827af4787e74 ("Bluetooth: MGMT: Add initial implementation of MGMT_OP_HCI_CMD_SYNC")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In 'mgmt_mesh_foreach()', iterate over mesh commands
rather than generic mgmt ones. Compile tested only.
Fixes: b338d91703fa ("Bluetooth: Implement support for Mesh")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
l2cap_check_enc_key_size shall check the security level of the
l2cap_chan rather than the hci_conn since for incoming connection
request that may be different as hci_conn may already been
encrypted using a different security level.
Fixes: 522e9ed157e3 ("Bluetooth: l2cap: Check encryption key size on incoming connection")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use separate link type id for unicast and broadcast ISO connections.
These connection types are handled with separate HCI commands, socket
API is different, and hci_conn has union fields that are different in
the two cases, so they shall not be mixed up.
Currently in most places it is attempted to distinguish ucast by
bacmp(&c->dst, BDADDR_ANY) but it is wrong as dst is set for bcast sink
hci_conn in iso_conn_ready(). Additionally checking sync_handle might be
OK, but depends on details of bcast conn configuration flow.
To avoid complicating it, use separate link types.
Fixes: f764a6c2c1e4 ("Bluetooth: ISO: Add broadcast support")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Bluetooth needs some way for user to get supported so_timestamping flags
for the different socket types.
Use SIOCETHTOOL API for this purpose. As hci_dev is not associated with
struct net_device, the existing implementation can't be reused, so we
add a small one here.
Add support (only) for ETHTOOL_GET_TS_INFO command. The API differs
slightly from netdev in that the result depends also on socket type.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If the socket is a broadcast receiver fields from sockaddr_iso_bc shall
be part of the values returned to getpeername since some of these fields
are updated while doing the PA and BIG sync procedures.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Up until now it has been assumed that the application would be able to
enter the advertising SID in sockaddr_iso_bc.bc_sid, but userspace has
no access to SID since the likes of MGMT_EV_DEVICE_FOUND cannot carry
it, so it was left unset (0x00) which means it would be unable to
synchronize if the broadcast source is using a different SID e.g. 0x04:
> HCI Event: LE Meta Event (0x3e) plen 57
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x0000
Props: 0x0000
Data status: Complete
Address type: Random (0x01)
Address: 0B:82:E8:50:6D:C8 (Non-Resolvable)
Primary PHY: LE 1M
Secondary PHY: LE 2M
SID: 0x04
TX power: 127 dBm
RSSI: -55 dBm (0xc9)
Periodic advertising interval: 180.00 msec (0x0090)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
Data length: 0x1f
06 16 52 18 5b 0b e1 05 16 56 18 04 00 11 30 4c ..R.[....V....0L
75 69 7a 27 73 20 53 32 33 20 55 6c 74 72 61 uiz's S23 Ultra
Service Data: Broadcast Audio Announcement (0x1852)
Broadcast ID: 14748507 (0xe10b5b)
Service Data: Public Broadcast Announcement (0x1856)
Data[2]: 0400
Unknown EIR field 0x30[16]: 4c75697a27732053323320556c747261
< HCI Command: LE Periodic Advertising Create Sync (0x08|0x0044) plen 14
Options: 0x0000
Use advertising SID, Advertiser Address Type and address
Reporting initially enabled
SID: 0x00 (<- Invalid)
Adv address type: Random (0x01)
Adv address: 0B:82:E8:50:6D:C8 (Non-Resolvable)
Skip: 0x0000
Sync timeout: 20000 msec (0x07d0)
Sync CTE type: 0x0000
So instead this changes now allow application to set HCI_SID_INVALID
which will make hci_le_pa_create_sync to wait for a report, update the
conn->sid using the report SID and only then issue PA create sync
command:
< HCI Command: LE Periodic Advertising Create Sync
Options: 0x0000
Use advertising SID, Advertiser Address Type and address
Reporting initially enabled
SID: 0x04
Adv address type: Random (0x01)
Adv address: 0B:82:E8:50:6D:C8 (Non-Resolvable)
Skip: 0x0000
Sync timeout: 20000 msec (0x07d0)
Sync CTE type: 0x0000
> HCI Event: LE Meta Event (0x3e) plen 16
LE Periodic Advertising Sync Established (0x0e)
Status: Success (0x00)
Sync handle: 64
Advertising SID: 0x04
Advertiser address type: Random (0x01)
Advertiser address: 0B:82:E8:50:6D:C8 (Non-Resolvable)
Advertiser PHY: LE 2M (0x02)
Periodic advertising interval: 180.00 msec (0x0090)
Advertiser clock accuracy: 0x05
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
