From 3900abd5bb7557e1f8463f6aa6981b1475ec89d2 Mon Sep 17 00:00:00 2001
From: Christer Weinigel <christer@weinigel.se>
Date: Fri, 4 Oct 2002 20:13:10 -0700
Subject: [PATCH] Updated NatSemi SCx200 patches for Linux-2.5

This patch adds support for the National Semiconductor SCx200
processor family to Linux 2.5.

The patch consists of the following drivers:

  arch/i386/kernel/scx200.c -- give kernel access to the GPIO pins

  drivers/chars/scx200_gpio.c -- give userspace access to the GPIO pins
  drivers/chars/scx200_wdt.c -- watchdog timer driver

  drivers/i2c/scx200_i2c.c -- use any two GPIO pins as an I2C bus
  drivers/i2c/scx200_acb.c -- driver for the Access.BUS hardware

  drivers/mtd/maps/scx200_docflash.c -- driver for a CFI flash connected
                                      to the DOCCS pin
---
 include/linux/pci_ids.h     |  6 +++
 include/linux/scx200.h      | 56 ++++++++++++++++++++++++++
 include/linux/scx200_gpio.h | 98 +++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 160 insertions(+)
 create mode 100644 include/linux/scx200.h
 create mode 100644 include/linux/scx200_gpio.h

(limited to 'include/linux')

diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index be4d21956fc5..a652bbf6682d 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -288,6 +288,12 @@
 #define PCI_DEVICE_ID_NS_87560_USB	0x0012
 #define PCI_DEVICE_ID_NS_83815		0x0020
 #define PCI_DEVICE_ID_NS_83820		0x0022
+#define PCI_DEVICE_ID_NS_SCx200_BRIDGE	0x0500
+#define PCI_DEVICE_ID_NS_SCx200_SMI	0x0501
+#define PCI_DEVICE_ID_NS_SCx200_IDE	0x0502
+#define PCI_DEVICE_ID_NS_SCx200_AUDIO	0x0503
+#define PCI_DEVICE_ID_NS_SCx200_VIDEO	0x0504
+#define PCI_DEVICE_ID_NS_SCx200_XBUS	0x0505
 #define PCI_DEVICE_ID_NS_87410		0xd001
 
 #define PCI_VENDOR_ID_TSENG		0x100c
diff --git a/include/linux/scx200.h b/include/linux/scx200.h
new file mode 100644
index 000000000000..af7d53acad99
--- /dev/null
+++ b/include/linux/scx200.h
@@ -0,0 +1,56 @@
+/* linux/include/linux/scx200.h
+
+   Copyright (c) 2001,2002 Christer Weinigel <wingel@nano-system.com>
+
+   Defines for the National Semiconductor SCx200 Processors
+*/
+
+/* Interesting stuff for the National Semiconductor SCx200 CPU */
+
+/* F0 PCI Header/Bridge Configuration Registers */
+#define SCx200_DOCCS_BASE 0x78	/* DOCCS Base Address Register */
+#define SCx200_DOCCS_CTRL 0x7c	/* DOCCS Control Register */
+
+/* GPIO Register Block */
+#define SCx200_GPIO_SIZE 0x2c	/* Size of GPIO register block */
+
+/* General Configuration Block */
+#define SCx200_CB_BASE 0x9000	/* Base fixed at 0x9000 according to errata */
+
+/* Watchdog Timer */
+#define SCx200_WDT_OFFSET 0x00	/* offset within configuration block */
+#define SCx200_WDT_SIZE 0x05	/* size */
+
+#define SCx200_WDT_WDTO 0x00	/* Time-Out Register */
+#define SCx200_WDT_WDCNFG 0x02	/* Configuration Register */
+#define SCx200_WDT_WDSTS 0x04	/* Status Register */
+#define SCx200_WDT_WDSTS_WDOVF (1<<0) /* Overflow bit */
+
+/* High Resolution Timer */
+#define SCx200_TIMER_OFFSET 0x08
+#define SCx200_TIMER_SIZE 0x05
+
+/* Clock Generators */
+#define SCx200_CLOCKGEN_OFFSET 0x10
+#define SCx200_CLOCKGEN_SIZE 0x10
+
+/* Pin Multiplexing and Miscellaneous Configuration Registers */
+#define SCx200_MISC_OFFSET 0x30
+#define SCx200_MISC_SIZE 0x10
+
+#define SCx200_PMR 0x30		/* Pin Multiplexing Register */
+#define SCx200_MCR 0x34		/* Miscellaneous Configuration Register */
+#define SCx200_INTSEL 0x38	/* Interrupt Selection Register */
+#define SCx200_IID 0x3c		/* IA On a Chip Identification Number Reg */
+#define SCx200_REV 0x3d		/* Revision Register */
+#define SCx200_CBA 0x3e		/* Configuration Base Address Register */
+
+/* Verify that the configuration block really is there */
+#define scx200_cb_probe(base) (inw((base) + SCx200_CBA) == (base))
+
+/*
+    Local variables:
+        compile-command: "make -C ../.. bzImage modules"
+        c-basic-offset: 8
+    End:
+*/
diff --git a/include/linux/scx200_gpio.h b/include/linux/scx200_gpio.h
new file mode 100644
index 000000000000..2c6d739706b6
--- /dev/null
+++ b/include/linux/scx200_gpio.h
@@ -0,0 +1,98 @@
+#include <linux/spinlock.h>
+
+u32 scx200_gpio_configure(int index, u32 set, u32 clear);
+void scx200_gpio_dump(unsigned index);
+
+extern unsigned scx200_gpio_base;
+extern spinlock_t scx200_gpio_lock;
+extern long scx200_gpio_shadow[2];
+
+#define scx200_gpio_present() (scx200_gpio_base!=0)
+
+/* Definitions to make sure I do the same thing in all functions */
+#define __SCx200_GPIO_BANK unsigned bank = index>>5
+#define __SCx200_GPIO_IOADDR unsigned short ioaddr = scx200_gpio_base+0x10*bank
+#define __SCx200_GPIO_SHADOW long *shadow = scx200_gpio_shadow+bank
+#define __SCx200_GPIO_INDEX index &= 31
+
+#define __SCx200_GPIO_OUT __asm__ __volatile__("outsl":"=mS" (shadow):"d" (ioaddr), "0" (shadow))
+
+/* returns the value of the GPIO pin */
+
+static inline int scx200_gpio_get(int index) {
+	__SCx200_GPIO_BANK;
+	__SCx200_GPIO_IOADDR + 0x04;
+	__SCx200_GPIO_INDEX;
+		
+	return (inl(ioaddr) & (1<<index)) ? 1 : 0;
+}
+
+/* return the value driven on the GPIO signal (the value that will be
+   driven if the GPIO is configured as an output, it might not be the
+   state of the GPIO right now if the GPIO is configured as an input) */
+
+static inline int scx200_gpio_current(int index) {
+        __SCx200_GPIO_BANK;
+	__SCx200_GPIO_INDEX;
+		
+	return (scx200_gpio_shadow[bank] & (1<<index)) ? 1 : 0;
+}
+
+/* drive the GPIO signal high */
+
+static inline void scx200_gpio_set_high(int index) {
+	__SCx200_GPIO_BANK;
+	__SCx200_GPIO_IOADDR;
+	__SCx200_GPIO_SHADOW;
+	__SCx200_GPIO_INDEX;
+	set_bit(index, shadow);
+	__SCx200_GPIO_OUT;
+}
+
+/* drive the GPIO signal low */
+
+static inline void scx200_gpio_set_low(int index) {
+	__SCx200_GPIO_BANK;
+	__SCx200_GPIO_IOADDR;
+	__SCx200_GPIO_SHADOW;
+	__SCx200_GPIO_INDEX;
+	clear_bit(index, shadow);
+	__SCx200_GPIO_OUT;
+}
+
+/* drive the GPIO signal to state */
+
+static inline void scx200_gpio_set(int index, int state) {
+	__SCx200_GPIO_BANK;
+	__SCx200_GPIO_IOADDR;
+	__SCx200_GPIO_SHADOW;
+	__SCx200_GPIO_INDEX;
+	if (state)
+		set_bit(index, shadow);
+	else
+		clear_bit(index, shadow);
+	__SCx200_GPIO_OUT;
+}
+
+/* toggle the GPIO signal */
+static inline void scx200_gpio_change(int index) {
+	__SCx200_GPIO_BANK;
+	__SCx200_GPIO_IOADDR;
+	__SCx200_GPIO_SHADOW;
+	__SCx200_GPIO_INDEX;
+	change_bit(index, shadow);
+	__SCx200_GPIO_OUT;
+}
+
+#undef __SCx200_GPIO_BANK
+#undef __SCx200_GPIO_IOADDR
+#undef __SCx200_GPIO_SHADOW
+#undef __SCx200_GPIO_INDEX
+#undef __SCx200_GPIO_OUT
+
+/*
+    Local variables:
+        compile-command: "make -C ../.. bzImage modules"
+        c-basic-offset: 8
+    End:
+*/
-- 
cgit v1.2.3