From d582cffbcd04eae0bd8a83b05648bfd54bfd21c9 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Fri, 26 Oct 2012 17:53:44 +0200 Subject: nl80211/mac80211: support full station state in AP mode Today, stations are added already associated. That is inefficient if, for example, the driver has no room for stations any more because then the station will go through the entire auth/assoc handshake, only to be kicked out afterwards. To address this a bit better, at least with drivers using the new station state callback, allow hostapd to add stations in unauthenticated mode, just after receiving the AUTH frame, before even replying. Thus if there's no more space at that point, it can send a negative auth frame back. It still needs to handle later state transition errors though, of course. Signed-off-by: Johannes Berg --- include/uapi/linux/nl80211.h | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'include/uapi/linux') diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index e3e19f8b16f2..547017100a30 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -1697,6 +1697,9 @@ enum nl80211_iftype { * flag can't be changed, it is only valid while adding a station, and * attempts to change it will silently be ignored (rather than rejected * as errors.) + * @NL80211_STA_FLAG_ASSOCIATED: station is associated; used with drivers + * that support %NL80211_FEATURE_FULL_AP_CLIENT_STATE to transition a + * previously added station into associated state * @NL80211_STA_FLAG_MAX: highest station flag number currently defined * @__NL80211_STA_FLAG_AFTER_LAST: internal use */ @@ -1708,6 +1711,7 @@ enum nl80211_sta_flags { NL80211_STA_FLAG_MFP, NL80211_STA_FLAG_AUTHENTICATED, NL80211_STA_FLAG_TDLS_PEER, + NL80211_STA_FLAG_ASSOCIATED, /* keep last */ __NL80211_STA_FLAG_AFTER_LAST, @@ -3140,6 +3144,17 @@ enum nl80211_ap_sme_features { * setting * @NL80211_FEATURE_P2P_GO_OPPPS: P2P GO implementation supports opportunistic * powersave + * @NL80211_FEATURE_FULL_AP_CLIENT_STATE: The driver supports full state + * transitions for AP clients. Without this flag (and if the driver + * doesn't have the AP SME in the device) the driver supports adding + * stations only when they're associated and adds them in associated + * state (to later be transitioned into authorized), with this flag + * they should be added before even sending the authentication reply + * and then transitioned into authenticated, associated and authorized + * states using station flags. + * Note that even for drivers that support this, the default is to add + * stations in authenticated/associated state, so to add unauthenticated + * stations the authenticated/associated bits have to be set in the mask. */ enum nl80211_feature_flags { NL80211_FEATURE_SK_TX_STATUS = 1 << 0, @@ -3155,6 +3170,7 @@ enum nl80211_feature_flags { NL80211_FEATURE_NEED_OBSS_SCAN = 1 << 10, NL80211_FEATURE_P2P_GO_CTWIN = 1 << 11, NL80211_FEATURE_P2P_GO_OPPPS = 1 << 12, + NL80211_FEATURE_FULL_AP_CLIENT_STATE = 1 << 13, }; /** -- cgit v1.2.3 From 390a1bd8538132186ddb679cafe9e75b7ef7e2d2 Mon Sep 17 00:00:00 2001 From: Samuel Ortiz Date: Wed, 19 Dec 2012 19:11:32 +0100 Subject: NFC: Initial Secure Element API Each NFC adapter can have several links to different secure elements and that property needs to be exported by the drivers. A secure element link can be enabled and disabled, and card emulation will be handled by the currently active one. Otherwise card emulation will be host implemented. Signed-off-by: Samuel Ortiz --- drivers/nfc/nfcwilink.c | 1 + drivers/nfc/pn533.c | 1 + drivers/nfc/pn544/pn544.c | 6 ++++-- include/net/nfc/hci.h | 3 +++ include/net/nfc/nci_core.h | 1 + include/net/nfc/nfc.h | 6 ++++++ include/uapi/linux/nfc.h | 14 ++++++++++++++ net/nfc/core.c | 3 +++ net/nfc/hci/core.c | 3 ++- net/nfc/nci/core.c | 2 ++ net/nfc/netlink.c | 1 + 11 files changed, 38 insertions(+), 3 deletions(-) (limited to 'include/uapi/linux') diff --git a/drivers/nfc/nfcwilink.c b/drivers/nfc/nfcwilink.c index c7c182d2b7df..3b731acbc408 100644 --- a/drivers/nfc/nfcwilink.c +++ b/drivers/nfc/nfcwilink.c @@ -542,6 +542,7 @@ static int nfcwilink_probe(struct platform_device *pdev) drv->ndev = nci_allocate_device(&nfcwilink_ops, protocols, + NFC_SE_NONE, NFCWILINK_HDR_LEN, 0); if (!drv->ndev) { diff --git a/drivers/nfc/pn533.c b/drivers/nfc/pn533.c index e8c083203b33..31a5b3b53b2a 100644 --- a/drivers/nfc/pn533.c +++ b/drivers/nfc/pn533.c @@ -2525,6 +2525,7 @@ static int pn533_probe(struct usb_interface *interface, dev->nfc_dev = nfc_allocate_device(&pn533_nfc_ops, protocols, + NFC_SE_NONE, dev->ops->tx_header_len + PN533_CMD_DATAEXCH_HEAD_LEN, dev->ops->tx_tail_len); diff --git a/drivers/nfc/pn544/pn544.c b/drivers/nfc/pn544/pn544.c index d108c794008d..9c5f16e7baef 100644 --- a/drivers/nfc/pn544/pn544.c +++ b/drivers/nfc/pn544/pn544.c @@ -801,7 +801,7 @@ int pn544_hci_probe(void *phy_id, struct nfc_phy_ops *phy_ops, char *llc_name, struct nfc_hci_dev **hdev) { struct pn544_hci_info *info; - u32 protocols; + u32 protocols, se; struct nfc_hci_init_data init_data; int r; @@ -834,8 +834,10 @@ int pn544_hci_probe(void *phy_id, struct nfc_phy_ops *phy_ops, char *llc_name, NFC_PROTO_ISO14443_B_MASK | NFC_PROTO_NFC_DEP_MASK; + se = NFC_SE_UICC | NFC_SE_EMBEDDED; + info->hdev = nfc_hci_allocate_device(&pn544_hci_ops, &init_data, 0, - protocols, llc_name, + protocols, se, llc_name, phy_headroom + PN544_CMDS_HEADROOM, phy_tailroom, phy_payload); if (!info->hdev) { diff --git a/include/net/nfc/hci.h b/include/net/nfc/hci.h index 2ff71750c428..b87a1692b086 100644 --- a/include/net/nfc/hci.h +++ b/include/net/nfc/hci.h @@ -59,6 +59,8 @@ struct nfc_hci_ops { struct nfc_target *target); int (*event_received)(struct nfc_hci_dev *hdev, u8 gate, u8 event, struct sk_buff *skb); + int (*enable_se)(struct nfc_dev *dev, u32 secure_element); + int (*disable_se)(struct nfc_dev *dev, u32 secure_element); }; /* Pipes */ @@ -150,6 +152,7 @@ struct nfc_hci_dev *nfc_hci_allocate_device(struct nfc_hci_ops *ops, struct nfc_hci_init_data *init_data, unsigned long quirks, u32 protocols, + u32 supported_se, const char *llc_name, int tx_headroom, int tx_tailroom, diff --git a/include/net/nfc/nci_core.h b/include/net/nfc/nci_core.h index d705d8674949..5bc0c460edc0 100644 --- a/include/net/nfc/nci_core.h +++ b/include/net/nfc/nci_core.h @@ -147,6 +147,7 @@ struct nci_dev { /* ----- NCI Devices ----- */ struct nci_dev *nci_allocate_device(struct nci_ops *ops, __u32 supported_protocols, + __u32 supported_se, int tx_headroom, int tx_tailroom); void nci_free_device(struct nci_dev *ndev); diff --git a/include/net/nfc/nfc.h b/include/net/nfc/nfc.h index 1665674e86b2..87a6417fc934 100644 --- a/include/net/nfc/nfc.h +++ b/include/net/nfc/nfc.h @@ -68,6 +68,8 @@ struct nfc_ops { void *cb_context); int (*tm_send)(struct nfc_dev *dev, struct sk_buff *skb); int (*check_presence)(struct nfc_dev *dev, struct nfc_target *target); + int (*enable_se)(struct nfc_dev *dev, u32 secure_element); + int (*disable_se)(struct nfc_dev *dev, u32 secure_element); }; #define NFC_TARGET_IDX_ANY -1 @@ -109,6 +111,9 @@ struct nfc_dev { struct nfc_genl_data genl_data; u32 supported_protocols; + u32 supported_se; + u32 active_se; + int tx_headroom; int tx_tailroom; @@ -125,6 +130,7 @@ extern struct class nfc_class; struct nfc_dev *nfc_allocate_device(struct nfc_ops *ops, u32 supported_protocols, + u32 supported_se, int tx_headroom, int tx_tailroom); diff --git a/include/uapi/linux/nfc.h b/include/uapi/linux/nfc.h index 0e63cee8d810..80e4ecd8c04c 100644 --- a/include/uapi/linux/nfc.h +++ b/include/uapi/linux/nfc.h @@ -67,6 +67,11 @@ * subsequent CONNECT and CC messages. * If one of the passed parameters is wrong none is set and -EINVAL is * returned. + * @NFC_CMD_ENABLE_SE: Enable the physical link to a specific secure element. + * Once enabled a secure element will handle card emulation mode, i.e. + * starting a poll from a device which has a secure element enabled means + * we want to do SE based card emulation. + * @NFC_CMD_DISABLE_SE: Disable the physical link to a specific secure element. */ enum nfc_commands { NFC_CMD_UNSPEC, @@ -86,6 +91,8 @@ enum nfc_commands { NFC_EVENT_TM_DEACTIVATED, NFC_CMD_LLC_GET_PARAMS, NFC_CMD_LLC_SET_PARAMS, + NFC_CMD_ENABLE_SE, + NFC_CMD_DISABLE_SE, /* private: internal use only */ __NFC_CMD_AFTER_LAST }; @@ -114,6 +121,7 @@ enum nfc_commands { * @NFC_ATTR_LLC_PARAM_LTO: Link TimeOut parameter * @NFC_ATTR_LLC_PARAM_RW: Receive Window size parameter * @NFC_ATTR_LLC_PARAM_MIUX: MIU eXtension parameter + * @NFC_ATTR_SE: Available Secure Elements */ enum nfc_attrs { NFC_ATTR_UNSPEC, @@ -134,6 +142,7 @@ enum nfc_attrs { NFC_ATTR_LLC_PARAM_LTO, NFC_ATTR_LLC_PARAM_RW, NFC_ATTR_LLC_PARAM_MIUX, + NFC_ATTR_SE, /* private: internal use only */ __NFC_ATTR_AFTER_LAST }; @@ -172,6 +181,11 @@ enum nfc_attrs { #define NFC_PROTO_NFC_DEP_MASK (1 << NFC_PROTO_NFC_DEP) #define NFC_PROTO_ISO14443_B_MASK (1 << NFC_PROTO_ISO14443_B) +/* NFC Secure Elements */ +#define NFC_SE_NONE 0x0 +#define NFC_SE_UICC 0x1 +#define NFC_SE_EMBEDDED 0x2 + struct sockaddr_nfc { sa_family_t sa_family; __u32 dev_idx; diff --git a/net/nfc/core.c b/net/nfc/core.c index 7d7b4ee34015..25522e56d350 100644 --- a/net/nfc/core.c +++ b/net/nfc/core.c @@ -757,6 +757,7 @@ struct nfc_dev *nfc_get_device(unsigned int idx) */ struct nfc_dev *nfc_allocate_device(struct nfc_ops *ops, u32 supported_protocols, + u32 supported_se, int tx_headroom, int tx_tailroom) { struct nfc_dev *dev; @@ -774,6 +775,8 @@ struct nfc_dev *nfc_allocate_device(struct nfc_ops *ops, dev->ops = ops; dev->supported_protocols = supported_protocols; + dev->supported_se = supported_se; + dev->active_se = NFC_SE_NONE; dev->tx_headroom = tx_headroom; dev->tx_tailroom = tx_tailroom; diff --git a/net/nfc/hci/core.c b/net/nfc/hci/core.c index 755a6b9774ab..91020b210d87 100644 --- a/net/nfc/hci/core.c +++ b/net/nfc/hci/core.c @@ -797,6 +797,7 @@ struct nfc_hci_dev *nfc_hci_allocate_device(struct nfc_hci_ops *ops, struct nfc_hci_init_data *init_data, unsigned long quirks, u32 protocols, + u32 supported_se, const char *llc_name, int tx_headroom, int tx_tailroom, @@ -822,7 +823,7 @@ struct nfc_hci_dev *nfc_hci_allocate_device(struct nfc_hci_ops *ops, return NULL; } - hdev->ndev = nfc_allocate_device(&hci_nfc_ops, protocols, + hdev->ndev = nfc_allocate_device(&hci_nfc_ops, protocols, supported_se, tx_headroom + HCI_CMDS_HEADROOM, tx_tailroom); if (!hdev->ndev) { diff --git a/net/nfc/nci/core.c b/net/nfc/nci/core.c index 5f98dc1bf039..48ada0ec749e 100644 --- a/net/nfc/nci/core.c +++ b/net/nfc/nci/core.c @@ -658,6 +658,7 @@ static struct nfc_ops nci_nfc_ops = { */ struct nci_dev *nci_allocate_device(struct nci_ops *ops, __u32 supported_protocols, + __u32 supported_se, int tx_headroom, int tx_tailroom) { struct nci_dev *ndev; @@ -680,6 +681,7 @@ struct nci_dev *nci_allocate_device(struct nci_ops *ops, ndev->nfc_dev = nfc_allocate_device(&nci_nfc_ops, supported_protocols, + supported_se, tx_headroom + NCI_DATA_HDR_SIZE, tx_tailroom); if (!ndev->nfc_dev) diff --git a/net/nfc/netlink.c b/net/nfc/netlink.c index 3568ae16786d..504b883439f1 100644 --- a/net/nfc/netlink.c +++ b/net/nfc/netlink.c @@ -366,6 +366,7 @@ static int nfc_genl_send_device(struct sk_buff *msg, struct nfc_dev *dev, if (nla_put_string(msg, NFC_ATTR_DEVICE_NAME, nfc_device_name(dev)) || nla_put_u32(msg, NFC_ATTR_DEVICE_INDEX, dev->idx) || nla_put_u32(msg, NFC_ATTR_PROTOCOLS, dev->supported_protocols) || + nla_put_u32(msg, NFC_ATTR_SE, dev->supported_se) || nla_put_u8(msg, NFC_ATTR_DEVICE_POWERED, dev->dev_up) || nla_put_u8(msg, NFC_ATTR_RF_MODE, dev->rf_mode)) goto nla_put_failure; -- cgit v1.2.3 From d3710e74cf329839dea8d13b1ad56e572b06b173 Mon Sep 17 00:00:00 2001 From: Lauro Ramos Venancio Date: Wed, 5 Dec 2012 21:12:25 -0300 Subject: NFC: Change nfc.h license nfc.h being GPL makes it quite controversial for non GPL applications to include it. Moreover, nfc.h only includes structures and API definitions that are hardly copyrightable. Signed-off-by: Lauro Ramos Venancio Signed-off-by: Samuel Ortiz --- include/uapi/linux/nfc.h | 23 ++++++++++------------- 1 file changed, 10 insertions(+), 13 deletions(-) (limited to 'include/uapi/linux') diff --git a/include/uapi/linux/nfc.h b/include/uapi/linux/nfc.h index 80e4ecd8c04c..7969f46f1bb3 100644 --- a/include/uapi/linux/nfc.h +++ b/include/uapi/linux/nfc.h @@ -5,20 +5,17 @@ * Lauro Ramos Venancio * Aloisio Almeida Jr * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the - * Free Software Foundation, Inc., - * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. */ #ifndef __LINUX_NFC_H -- cgit v1.2.3 From 3b1c5a5307fb5277f395efdcf330c064d79df07d Mon Sep 17 00:00:00 2001 From: Marco Porsch Date: Mon, 7 Jan 2013 16:04:52 +0100 Subject: {cfg,nl}80211: mesh power mode primitives and userspace access Add the nl80211_mesh_power_mode enumeration which holds possible values for the mesh power mode. These modes are unknown, active, light sleep and deep sleep. Add power_mode entry to the mesh config structure to hold the user-configured default mesh power mode. This value will be used for new peer links. Add the dot11MeshAwakeWindowDuration value to the mesh config. The awake window is a duration in TU describing how long the STA will stay awake after transmitting its beacon in PS mode. Add access routines to: - get/set local link-specific power mode (STA) - get remote STA's link-specific power mode (STA) - get remote STA's non-peer power mode (STA) - get/set default mesh power mode (mesh config) - get/set mesh awake window duration (mesh config) All config changes may be done at mesh runtime and take effect immediately. Signed-off-by: Marco Porsch Signed-off-by: Ivan Bezyazychnyy Signed-off-by: Mike Krinkin [fix commit message line length, error handling in set station] Signed-off-by: Johannes Berg --- include/net/cfg80211.h | 21 ++++++++++++++++++++ include/uapi/linux/nl80211.h | 47 ++++++++++++++++++++++++++++++++++++++++++++ net/wireless/mesh.c | 3 +++ net/wireless/nl80211.c | 43 +++++++++++++++++++++++++++++++++++++++- 4 files changed, 113 insertions(+), 1 deletion(-) (limited to 'include/uapi/linux') diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 516aded3697f..d9f08f65f7a5 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -610,6 +610,8 @@ enum station_parameters_apply_mask { * @sta_modify_mask: bitmap indicating which parameters changed * (for those that don't have a natural "no change" value), * see &enum station_parameters_apply_mask + * @local_pm: local link-specific mesh power save mode (no change when set + * to unknown) */ struct station_parameters { u8 *supported_rates; @@ -625,6 +627,7 @@ struct station_parameters { struct ieee80211_vht_cap *vht_capa; u8 uapsd_queues; u8 max_sp; + enum nl80211_mesh_power_mode local_pm; }; /** @@ -655,6 +658,9 @@ struct station_parameters { * @STATION_INFO_STA_FLAGS: @sta_flags filled * @STATION_INFO_BEACON_LOSS_COUNT: @beacon_loss_count filled * @STATION_INFO_T_OFFSET: @t_offset filled + * @STATION_INFO_LOCAL_PM: @local_pm filled + * @STATION_INFO_PEER_PM: @peer_pm filled + * @STATION_INFO_NONPEER_PM: @nonpeer_pm filled */ enum station_info_flags { STATION_INFO_INACTIVE_TIME = 1<<0, @@ -678,6 +684,9 @@ enum station_info_flags { STATION_INFO_STA_FLAGS = 1<<18, STATION_INFO_BEACON_LOSS_COUNT = 1<<19, STATION_INFO_T_OFFSET = 1<<20, + STATION_INFO_LOCAL_PM = 1<<21, + STATION_INFO_PEER_PM = 1<<22, + STATION_INFO_NONPEER_PM = 1<<23, }; /** @@ -791,6 +800,9 @@ struct sta_bss_parameters { * @sta_flags: station flags mask & values * @beacon_loss_count: Number of times beacon loss event has triggered. * @t_offset: Time offset of the station relative to this host. + * @local_pm: local mesh STA power save mode + * @peer_pm: peer mesh STA power save mode + * @nonpeer_pm: non-peer mesh STA power save mode */ struct station_info { u32 filled; @@ -820,6 +832,9 @@ struct station_info { u32 beacon_loss_count; s64 t_offset; + enum nl80211_mesh_power_mode local_pm; + enum nl80211_mesh_power_mode peer_pm; + enum nl80211_mesh_power_mode nonpeer_pm; /* * Note: Add a new enum station_info_flags value for each new field and @@ -995,6 +1010,10 @@ struct bss_parameters { * @dot11MeshHWMPconfirmationInterval: The minimum interval of time (in TUs) * during which a mesh STA can send only one Action frame containing * a PREQ element for root path confirmation. + * @power_mode: The default mesh power save mode which will be the initial + * setting for new peer links. + * @dot11MeshAwakeWindowDuration: The duration in TUs the STA will remain awake + * after transmitting its beacon. */ struct mesh_config { u16 dot11MeshRetryTimeout; @@ -1022,6 +1041,8 @@ struct mesh_config { u32 dot11MeshHWMPactivePathToRootTimeout; u16 dot11MeshHWMProotInterval; u16 dot11MeshHWMPconfirmationInterval; + enum nl80211_mesh_power_mode power_mode; + u16 dot11MeshAwakeWindowDuration; }; /** diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index 547017100a30..6c4f703ae890 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -1310,6 +1310,9 @@ enum nl80211_commands { * if not given in START_AP 0 is assumed, if not given in SET_BSS * no change is made. * + * @NL80211_ATTR_LOCAL_MESH_POWER_MODE: local mesh STA link-specific power mode + * defined in &enum nl80211_mesh_power_mode. + * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ @@ -1580,6 +1583,8 @@ enum nl80211_attrs { NL80211_ATTR_P2P_CTWINDOW, NL80211_ATTR_P2P_OPPPS, + NL80211_ATTR_LOCAL_MESH_POWER_MODE, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -1838,6 +1843,10 @@ enum nl80211_sta_bss_param { * @NL80211_STA_INFO_STA_FLAGS: Contains a struct nl80211_sta_flag_update. * @NL80211_STA_INFO_BEACON_LOSS: count of times beacon loss was detected (u32) * @NL80211_STA_INFO_T_OFFSET: timing offset with respect to this STA (s64) + * @NL80211_STA_INFO_LOCAL_PM: local mesh STA link-specific power mode + * @NL80211_STA_INFO_PEER_PM: peer mesh STA link-specific power mode + * @NL80211_STA_INFO_NONPEER_PM: neighbor mesh STA power save mode towards + * non-peer STA * @__NL80211_STA_INFO_AFTER_LAST: internal * @NL80211_STA_INFO_MAX: highest possible station info attribute */ @@ -1862,6 +1871,9 @@ enum nl80211_sta_info { NL80211_STA_INFO_STA_FLAGS, NL80211_STA_INFO_BEACON_LOSS, NL80211_STA_INFO_T_OFFSET, + NL80211_STA_INFO_LOCAL_PM, + NL80211_STA_INFO_PEER_PM, + NL80211_STA_INFO_NONPEER_PM, /* keep last */ __NL80211_STA_INFO_AFTER_LAST, @@ -2252,6 +2264,34 @@ enum nl80211_mntr_flags { NL80211_MNTR_FLAG_MAX = __NL80211_MNTR_FLAG_AFTER_LAST - 1 }; +/** + * enum nl80211_mesh_power_mode - mesh power save modes + * + * @NL80211_MESH_POWER_UNKNOWN: The mesh power mode of the mesh STA is + * not known or has not been set yet. + * @NL80211_MESH_POWER_ACTIVE: Active mesh power mode. The mesh STA is + * in Awake state all the time. + * @NL80211_MESH_POWER_LIGHT_SLEEP: Light sleep mode. The mesh STA will + * alternate between Active and Doze states, but will wake up for + * neighbor's beacons. + * @NL80211_MESH_POWER_DEEP_SLEEP: Deep sleep mode. The mesh STA will + * alternate between Active and Doze states, but may not wake up + * for neighbor's beacons. + * + * @__NL80211_MESH_POWER_AFTER_LAST - internal use + * @NL80211_MESH_POWER_MAX - highest possible power save level + */ + +enum nl80211_mesh_power_mode { + NL80211_MESH_POWER_UNKNOWN, + NL80211_MESH_POWER_ACTIVE, + NL80211_MESH_POWER_LIGHT_SLEEP, + NL80211_MESH_POWER_DEEP_SLEEP, + + __NL80211_MESH_POWER_AFTER_LAST, + NL80211_MESH_POWER_MAX = __NL80211_MESH_POWER_AFTER_LAST - 1 +}; + /** * enum nl80211_meshconf_params - mesh configuration parameters * @@ -2346,6 +2386,11 @@ enum nl80211_mntr_flags { * (in TUs) during which a mesh STA can send only one Action frame * containing a PREQ element for root path confirmation. * + * @NL80211_MESHCONF_POWER_MODE: Default mesh power mode for new peer links. + * type &enum nl80211_mesh_power_mode (u32) + * + * @NL80211_MESHCONF_AWAKE_WINDOW: awake window duration (in TUs) + * * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use */ enum nl80211_meshconf_params { @@ -2375,6 +2420,8 @@ enum nl80211_meshconf_params { NL80211_MESHCONF_HWMP_PATH_TO_ROOT_TIMEOUT, NL80211_MESHCONF_HWMP_ROOT_INTERVAL, NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL, + NL80211_MESHCONF_POWER_MODE, + NL80211_MESHCONF_AWAKE_WINDOW, /* keep last */ __NL80211_MESHCONF_ATTR_AFTER_LAST, diff --git a/net/wireless/mesh.c b/net/wireless/mesh.c index 0fe8ceb5444e..55957a284f6c 100644 --- a/net/wireless/mesh.c +++ b/net/wireless/mesh.c @@ -46,6 +46,7 @@ #define MESH_DEFAULT_BEACON_INTERVAL 1000 /* in 1024 us units (=TUs) */ #define MESH_DEFAULT_DTIM_PERIOD 2 +#define MESH_DEFAULT_AWAKE_WINDOW 10 /* in 1024 us units (=TUs) */ const struct mesh_config default_mesh_config = { .dot11MeshRetryTimeout = MESH_RET_T, @@ -72,6 +73,8 @@ const struct mesh_config default_mesh_config = { .dot11MeshHWMPactivePathToRootTimeout = MESH_PATH_TO_ROOT_TIMEOUT, .dot11MeshHWMProotInterval = MESH_ROOT_INTERVAL, .dot11MeshHWMPconfirmationInterval = MESH_ROOT_CONFIRMATION_INTERVAL, + .power_mode = NL80211_MESH_POWER_ACTIVE, + .dot11MeshAwakeWindowDuration = MESH_DEFAULT_AWAKE_WINDOW, }; const struct mesh_setup default_mesh_setup = { diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c index d5842eb35aec..1a7a710fe9bf 100644 --- a/net/wireless/nl80211.c +++ b/net/wireless/nl80211.c @@ -3001,6 +3001,18 @@ static int nl80211_send_station(struct sk_buff *msg, u32 portid, u32 seq, nla_put_u32(msg, NL80211_STA_INFO_BEACON_LOSS, sinfo->beacon_loss_count)) goto nla_put_failure; + if ((sinfo->filled & STATION_INFO_LOCAL_PM) && + nla_put_u32(msg, NL80211_STA_INFO_LOCAL_PM, + sinfo->local_pm)) + goto nla_put_failure; + if ((sinfo->filled & STATION_INFO_PEER_PM) && + nla_put_u32(msg, NL80211_STA_INFO_PEER_PM, + sinfo->peer_pm)) + goto nla_put_failure; + if ((sinfo->filled & STATION_INFO_NONPEER_PM) && + nla_put_u32(msg, NL80211_STA_INFO_NONPEER_PM, + sinfo->nonpeer_pm)) + goto nla_put_failure; if (sinfo->filled & STATION_INFO_BSS_PARAM) { bss_param = nla_nest_start(msg, NL80211_STA_INFO_BSS_PARAM); if (!bss_param) @@ -3206,6 +3218,17 @@ static int nl80211_set_station(struct sk_buff *skb, struct genl_info *info) params.plink_state = nla_get_u8(info->attrs[NL80211_ATTR_STA_PLINK_STATE]); + if (info->attrs[NL80211_ATTR_LOCAL_MESH_POWER_MODE]) { + enum nl80211_mesh_power_mode pm = nla_get_u32( + info->attrs[NL80211_ATTR_LOCAL_MESH_POWER_MODE]); + + if (pm <= NL80211_MESH_POWER_UNKNOWN || + pm > NL80211_MESH_POWER_MAX) + return -EINVAL; + + params.local_pm = pm; + } + switch (dev->ieee80211_ptr->iftype) { case NL80211_IFTYPE_AP: case NL80211_IFTYPE_AP_VLAN: @@ -3213,6 +3236,8 @@ static int nl80211_set_station(struct sk_buff *skb, struct genl_info *info) /* disallow mesh-specific things */ if (params.plink_action) return -EINVAL; + if (params.local_pm) + return -EINVAL; /* TDLS can't be set, ... */ if (params.sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER)) @@ -3265,6 +3290,8 @@ static int nl80211_set_station(struct sk_buff *skb, struct genl_info *info) /* disallow things sta doesn't support */ if (params.plink_action) return -EINVAL; + if (params.local_pm) + return -EINVAL; /* reject any changes other than AUTHORIZED */ if (params.sta_flags_mask & ~BIT(NL80211_STA_FLAG_AUTHORIZED)) return -EINVAL; @@ -3922,7 +3949,11 @@ static int nl80211_get_mesh_config(struct sk_buff *skb, nla_put_u16(msg, NL80211_MESHCONF_HWMP_ROOT_INTERVAL, cur_params.dot11MeshHWMProotInterval) || nla_put_u16(msg, NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL, - cur_params.dot11MeshHWMPconfirmationInterval)) + cur_params.dot11MeshHWMPconfirmationInterval) || + nla_put_u32(msg, NL80211_MESHCONF_POWER_MODE, + cur_params.power_mode) || + nla_put_u16(msg, NL80211_MESHCONF_AWAKE_WINDOW, + cur_params.dot11MeshAwakeWindowDuration)) goto nla_put_failure; nla_nest_end(msg, pinfoattr); genlmsg_end(msg, hdr); @@ -3961,6 +3992,8 @@ static const struct nla_policy nl80211_meshconf_params_policy[NL80211_MESHCONF_A [NL80211_MESHCONF_HWMP_PATH_TO_ROOT_TIMEOUT] = { .type = NLA_U32 }, [NL80211_MESHCONF_HWMP_ROOT_INTERVAL] = { .type = NLA_U16 }, [NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL] = { .type = NLA_U16 }, + [NL80211_MESHCONF_POWER_MODE] = { .type = NLA_U32 }, + [NL80211_MESHCONF_AWAKE_WINDOW] = { .type = NLA_U16 }, }; static const struct nla_policy @@ -4088,6 +4121,14 @@ do { \ 1, 65535, mask, NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL, nla_get_u16); + FILL_IN_MESH_PARAM_IF_SET(tb, cfg, power_mode, + NL80211_MESH_POWER_ACTIVE, + NL80211_MESH_POWER_MAX, + mask, NL80211_MESHCONF_POWER_MODE, + nla_get_u32); + FILL_IN_MESH_PARAM_IF_SET(tb, cfg, dot11MeshAwakeWindowDuration, + 0, 65535, mask, + NL80211_MESHCONF_AWAKE_WINDOW, nla_get_u16); if (mask_out) *mask_out = mask; -- cgit v1.2.3 From cee00a959c0a86571e6f99cf42f0261d7e54d2ae Mon Sep 17 00:00:00 2001 From: Jouni Malinen Date: Tue, 15 Jan 2013 17:15:57 +0200 Subject: cfg80211: Allow use_mfp to be specified with the connect command The NL80211_ATTR_USE_MFP attribute was originally added for NL80211_CMD_ASSOCIATE, but it is actually as useful (if not even more useful) with NL80211_CMD_CONNECT, so process that attribute with the connect command, too. Signed-off-by: Jouni Malinen Signed-off-by: Johannes Berg --- include/net/cfg80211.h | 2 ++ include/uapi/linux/nl80211.h | 6 +++--- net/wireless/nl80211.c | 9 +++++++++ net/wireless/sme.c | 3 ++- 4 files changed, 16 insertions(+), 4 deletions(-) (limited to 'include/uapi/linux') diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index d81e730962cc..f1686d460e6b 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -1465,6 +1465,7 @@ struct cfg80211_ibss_params { * @ie: IEs for association request * @ie_len: Length of assoc_ie in octets * @privacy: indicates whether privacy-enabled APs should be used + * @mfp: indicate whether management frame protection is used * @crypto: crypto settings * @key_len: length of WEP key for shared key authentication * @key_idx: index of WEP key for shared key authentication @@ -1485,6 +1486,7 @@ struct cfg80211_connect_params { u8 *ie; size_t ie_len; bool privacy; + enum nl80211_mfp mfp; struct cfg80211_crypto_settings crypto; const u8 *key; u8 key_len, key_idx; diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index 6c4f703ae890..d01c16220dc5 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -374,8 +374,8 @@ * requests to connect to a specified network but without separating * auth and assoc steps. For this, you need to specify the SSID in a * %NL80211_ATTR_SSID attribute, and can optionally specify the association - * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC, - * %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT, + * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_USE_MFP, + * %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT, * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT. * Background scan period can optionally be @@ -958,7 +958,7 @@ enum nl80211_commands { * @NL80211_ATTR_USE_MFP: Whether management frame protection (IEEE 802.11w) is * used for the association (&enum nl80211_mfp, represented as a u32); * this attribute can be used - * with %NL80211_CMD_ASSOCIATE request + * with %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests * * @NL80211_ATTR_STA_FLAGS2: Attribute containing a * &struct nl80211_sta_flag_update. diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c index d543cf152100..df82a5c9faee 100644 --- a/net/wireless/nl80211.c +++ b/net/wireless/nl80211.c @@ -5932,6 +5932,15 @@ static int nl80211_connect(struct sk_buff *skb, struct genl_info *info) connect.ie_len = nla_len(info->attrs[NL80211_ATTR_IE]); } + if (info->attrs[NL80211_ATTR_USE_MFP]) { + connect.mfp = nla_get_u32(info->attrs[NL80211_ATTR_USE_MFP]); + if (connect.mfp != NL80211_MFP_REQUIRED && + connect.mfp != NL80211_MFP_NO) + return -EINVAL; + } else { + connect.mfp = NL80211_MFP_NO; + } + if (info->attrs[NL80211_ATTR_WIPHY_FREQ]) { connect.channel = ieee80211_get_channel(wiphy, diff --git a/net/wireless/sme.c b/net/wireless/sme.c index d2d26518cdd7..a825dfe12cf7 100644 --- a/net/wireless/sme.c +++ b/net/wireless/sme.c @@ -192,7 +192,8 @@ static int cfg80211_conn_do_work(struct wireless_dev *wdev) prev_bssid, params->ssid, params->ssid_len, params->ie, params->ie_len, - false, ¶ms->crypto, + params->mfp != NL80211_MFP_NO, + ¶ms->crypto, params->flags, ¶ms->ht_capa, ¶ms->ht_capa_mask); if (err) -- cgit v1.2.3 From 11c4a075db2f8774d37544342c8cb9752b4db9e1 Mon Sep 17 00:00:00 2001 From: Simon Wunderlich Date: Tue, 8 Jan 2013 14:04:07 +0100 Subject: cfg80211: check radar interface combinations To ease further DFS development regarding interface combinations, use the interface combinations structure to test for radar capabilities. Drivers can specify which channel widths they support, and in which modes. Right now only a single AP interface is allowed, but as the DFS code evolves other combinations can be enabled. Signed-off-by: Simon Wunderlich Signed-off-by: Johannes Berg --- include/net/cfg80211.h | 2 ++ include/uapi/linux/nl80211.h | 3 +++ net/wireless/core.c | 12 ++++++++++-- net/wireless/core.h | 7 ++++--- net/wireless/nl80211.c | 3 +++ net/wireless/util.c | 41 ++++++++++++++++++++++++++++++++++++++--- 6 files changed, 60 insertions(+), 8 deletions(-) (limited to 'include/uapi/linux') diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index f1686d460e6b..970da4420676 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -2125,6 +2125,7 @@ struct ieee80211_iface_limit { * @beacon_int_infra_match: In this combination, the beacon intervals * between infrastructure and AP types must match. This is required * only in special cases. + * @radar_detect_widths: bitmap of channel widths supported for radar detection * * These examples can be expressed as follows: * @@ -2177,6 +2178,7 @@ struct ieee80211_iface_combination { u16 max_interfaces; u8 n_limits; bool beacon_int_infra_match; + u8 radar_detect_widths; }; struct mac_address { diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index d01c16220dc5..e6eeb4ba5dc5 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -2984,6 +2984,8 @@ enum nl80211_iface_limit_attrs { * the infrastructure network's beacon interval. * @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many * different channels may be used within this group. + * @NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS: u32 attribute containing the bitmap + * of supported channel widths for radar detection. * @NUM_NL80211_IFACE_COMB: number of attributes * @MAX_NL80211_IFACE_COMB: highest attribute number * @@ -3016,6 +3018,7 @@ enum nl80211_if_combination_attrs { NL80211_IFACE_COMB_MAXNUM, NL80211_IFACE_COMB_STA_AP_BI_MATCH, NL80211_IFACE_COMB_NUM_CHANNELS, + NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS, /* keep last */ NUM_NL80211_IFACE_COMB, diff --git a/net/wireless/core.c b/net/wireless/core.c index 747dd9365a44..0e702cdc6043 100644 --- a/net/wireless/core.c +++ b/net/wireless/core.c @@ -382,8 +382,11 @@ static int wiphy_verify_combinations(struct wiphy *wiphy) c = &wiphy->iface_combinations[i]; - /* Combinations with just one interface aren't real */ - if (WARN_ON(c->max_interfaces < 2)) + /* + * Combinations with just one interface aren't real, + * however we make an exception for DFS. + */ + if (WARN_ON((c->max_interfaces < 2) && !c->radar_detect_widths)) return -EINVAL; /* Need at least one channel */ @@ -398,6 +401,11 @@ static int wiphy_verify_combinations(struct wiphy *wiphy) CFG80211_MAX_NUM_DIFFERENT_CHANNELS)) return -EINVAL; + /* DFS only works on one channel. */ + if (WARN_ON(c->radar_detect_widths && + (c->num_different_channels > 1))) + return -EINVAL; + if (WARN_ON(!c->n_limits)) return -EINVAL; diff --git a/net/wireless/core.h b/net/wireless/core.h index f342267e3620..8396f7671c8d 100644 --- a/net/wireless/core.h +++ b/net/wireless/core.h @@ -425,7 +425,8 @@ int cfg80211_can_use_iftype_chan(struct cfg80211_registered_device *rdev, struct wireless_dev *wdev, enum nl80211_iftype iftype, struct ieee80211_channel *chan, - enum cfg80211_chan_mode chanmode); + enum cfg80211_chan_mode chanmode, + u8 radar_detect); static inline int cfg80211_can_change_interface(struct cfg80211_registered_device *rdev, @@ -433,7 +434,7 @@ cfg80211_can_change_interface(struct cfg80211_registered_device *rdev, enum nl80211_iftype iftype) { return cfg80211_can_use_iftype_chan(rdev, wdev, iftype, NULL, - CHAN_MODE_UNDEFINED); + CHAN_MODE_UNDEFINED, 0); } static inline int @@ -450,7 +451,7 @@ cfg80211_can_use_chan(struct cfg80211_registered_device *rdev, enum cfg80211_chan_mode chanmode) { return cfg80211_can_use_iftype_chan(rdev, wdev, wdev->iftype, - chan, chanmode); + chan, chanmode, 0); } void diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c index df82a5c9faee..33de80364c5c 100644 --- a/net/wireless/nl80211.c +++ b/net/wireless/nl80211.c @@ -856,6 +856,9 @@ static int nl80211_put_iface_combinations(struct wiphy *wiphy, nla_put_u32(msg, NL80211_IFACE_COMB_MAXNUM, c->max_interfaces)) goto nla_put_failure; + if (nla_put_u32(msg, NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS, + c->radar_detect_widths)) + goto nla_put_failure; nla_nest_end(msg, nl_combi); } diff --git a/net/wireless/util.c b/net/wireless/util.c index 16d76a807c2f..1c2795d52db0 100644 --- a/net/wireless/util.c +++ b/net/wireless/util.c @@ -1184,7 +1184,8 @@ int cfg80211_can_use_iftype_chan(struct cfg80211_registered_device *rdev, struct wireless_dev *wdev, enum nl80211_iftype iftype, struct ieee80211_channel *chan, - enum cfg80211_chan_mode chanmode) + enum cfg80211_chan_mode chanmode, + u8 radar_detect) { struct wireless_dev *wdev_iter; u32 used_iftypes = BIT(iftype); @@ -1195,14 +1196,45 @@ int cfg80211_can_use_iftype_chan(struct cfg80211_registered_device *rdev, enum cfg80211_chan_mode chmode; int num_different_channels = 0; int total = 1; + bool radar_required; int i, j; ASSERT_RTNL(); lockdep_assert_held(&rdev->devlist_mtx); + if (WARN_ON(hweight32(radar_detect) > 1)) + return -EINVAL; + + switch (iftype) { + case NL80211_IFTYPE_ADHOC: + case NL80211_IFTYPE_AP: + case NL80211_IFTYPE_AP_VLAN: + case NL80211_IFTYPE_MESH_POINT: + case NL80211_IFTYPE_P2P_GO: + case NL80211_IFTYPE_WDS: + radar_required = !!(chan->flags & IEEE80211_CHAN_RADAR); + break; + case NL80211_IFTYPE_P2P_CLIENT: + case NL80211_IFTYPE_STATION: + case NL80211_IFTYPE_MONITOR: + radar_required = false; + break; + case NL80211_IFTYPE_P2P_DEVICE: + case NUM_NL80211_IFTYPES: + case NL80211_IFTYPE_UNSPECIFIED: + default: + return -EINVAL; + } + + if (radar_required && !radar_detect) + return -EINVAL; + /* Always allow software iftypes */ - if (rdev->wiphy.software_iftypes & BIT(iftype)) + if (rdev->wiphy.software_iftypes & BIT(iftype)) { + if (radar_detect) + return -EINVAL; return 0; + } memset(num, 0, sizeof(num)); memset(used_channels, 0, sizeof(used_channels)); @@ -1275,7 +1307,7 @@ int cfg80211_can_use_iftype_chan(struct cfg80211_registered_device *rdev, used_iftypes |= BIT(wdev_iter->iftype); } - if (total == 1) + if (total == 1 && !radar_detect) return 0; for (i = 0; i < rdev->wiphy.n_iface_combinations; i++) { @@ -1308,6 +1340,9 @@ int cfg80211_can_use_iftype_chan(struct cfg80211_registered_device *rdev, } } + if (radar_detect && !(c->radar_detect_widths & radar_detect)) + goto cont; + /* * Finally check that all iftypes that we're currently * using are actually part of this combination. If they -- cgit v1.2.3