diff options
| -rw-r--r-- | ports/stm32/boards/NADHAT_PYBF405/mpconfigboard.h | 105 | ||||
| -rw-r--r-- | ports/stm32/boards/NADHAT_PYBF405/mpconfigboard.mk | 13 | ||||
| -rw-r--r-- | ports/stm32/boards/NADHAT_PYBF405/pins.csv | 58 | ||||
| -rw-r--r-- | ports/stm32/boards/NADHAT_PYBF405/stm32f4xx_hal_conf.h | 19 |
4 files changed, 195 insertions, 0 deletions
diff --git a/ports/stm32/boards/NADHAT_PYBF405/mpconfigboard.h b/ports/stm32/boards/NADHAT_PYBF405/mpconfigboard.h new file mode 100644 index 000000000..c6f1a7bc6 --- /dev/null +++ b/ports/stm32/boards/NADHAT_PYBF405/mpconfigboard.h @@ -0,0 +1,105 @@ +#define MICROPY_HW_BOARD_NAME "NADHAT_PYBF405" +#define MICROPY_HW_MCU_NAME "STM32F405RG" + +#define MICROPY_HW_HAS_SWITCH (1) +#define MICROPY_HW_HAS_FLASH (1) +#define MICROPY_HW_HAS_KXTJ3 (1) +#define MICROPY_HW_HAS_LCD (1) +#define MICROPY_HW_ENABLE_RNG (1) +#define MICROPY_HW_ENABLE_RTC (1) +#define MICROPY_HW_ENABLE_SERVO (1) +#define MICROPY_HW_ENABLE_DAC (1) +#define MICROPY_HW_ENABLE_USB (1) +#define MICROPY_HW_ENABLE_SDCARD (1) + +// HSE is 16MHz +#define MICROPY_HW_CLK_PLLM (16) +#define MICROPY_HW_CLK_PLLN (336) +#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) +#define MICROPY_HW_CLK_PLLQ (7) +#define MICROPY_HW_CLK_LAST_FREQ (1) + +// The board has a 32kHz crystal for the RTC +#define MICROPY_HW_RTC_USE_LSE (1) +#define MICROPY_HW_RTC_USE_US (0) +#define MICROPY_HW_RTC_USE_CALOUT (1) + +// UART config +#define MICROPY_HW_UART1_NAME "XB" +#define MICROPY_HW_UART1_TX (pin_B6) +#define MICROPY_HW_UART1_RX (pin_B7) +#define MICROPY_HW_UART2_TX (pin_A2) +#define MICROPY_HW_UART2_RX (pin_A3) +#define MICROPY_HW_UART2_RTS (pin_A1) +#define MICROPY_HW_UART2_CTS (pin_A0) +#define MICROPY_HW_UART3_NAME "YB" +#define MICROPY_HW_UART3_TX (pin_B10) +#define MICROPY_HW_UART3_RX (pin_B11) +#define MICROPY_HW_UART3_RTS (pin_B14) +#define MICROPY_HW_UART3_CTS (pin_B13) +#define MICROPY_HW_UART4_NAME "XA" +#define MICROPY_HW_UART4_TX (pin_A0) +#define MICROPY_HW_UART4_RX (pin_A1) +#define MICROPY_HW_UART6_NAME "YA" +#define MICROPY_HW_UART6_TX (pin_C6) +#define MICROPY_HW_UART6_RX (pin_C7) + +// I2C buses +#define MICROPY_HW_I2C1_NAME "X" +#define MICROPY_HW_I2C1_SCL (pin_B6) +#define MICROPY_HW_I2C1_SDA (pin_B7) +#define MICROPY_HW_I2C2_NAME "Y" +#define MICROPY_HW_I2C2_SCL (pin_B10) +#define MICROPY_HW_I2C2_SDA (pin_B11) + +// SPI buses +#define MICROPY_HW_SPI1_NAME "X" +#define MICROPY_HW_SPI1_NSS (pin_A4) // X5 +#define MICROPY_HW_SPI1_SCK (pin_A5) // X6 +#define MICROPY_HW_SPI1_MISO (pin_A6) // X7 +#define MICROPY_HW_SPI1_MOSI (pin_A7) // X8 +#define MICROPY_HW_SPI2_NAME "Y" +#define MICROPY_HW_SPI2_NSS (pin_B12) // Y5 +#define MICROPY_HW_SPI2_SCK (pin_B13) // Y6 +#define MICROPY_HW_SPI2_MISO (pin_B14) // Y7 +#define MICROPY_HW_SPI2_MOSI (pin_B15) // Y8 + +// CAN buses +#define MICROPY_HW_CAN1_NAME "YA" +#define MICROPY_HW_CAN1_TX (pin_B9) // Y4 +#define MICROPY_HW_CAN1_RX (pin_B8) // Y3 +#define MICROPY_HW_CAN2_NAME "YB" +#define MICROPY_HW_CAN2_TX (pin_B13) // Y6 +#define MICROPY_HW_CAN2_RX (pin_B12) // Y5 + +// USRSW has no pullup or pulldown, and pressing the switch makes the input go low +#define MICROPY_HW_USRSW_PIN (pin_B3) +#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP) +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) +#define MICROPY_HW_USRSW_PRESSED (0) + +// The board has 4 LEDs +#define MICROPY_HW_LED1 (pin_A13) // red +#define MICROPY_HW_LED2 (pin_A14) // green +#define MICROPY_HW_LED3 (pin_A15) // yellow +#define MICROPY_HW_LED4 (pin_B4) // blue +#define MICROPY_HW_LED3_PWM { TIM2, 2, TIM_CHANNEL_1, GPIO_AF1_TIM2 } +#define MICROPY_HW_LED4_PWM { TIM3, 3, TIM_CHANNEL_1, GPIO_AF2_TIM3 } +#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) +#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) + +// SD card detect switch +#define MICROPY_HW_SDCARD_DETECT_PIN (pin_A8) +#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP) +#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET) + +// USB config +#define MICROPY_HW_USB_FS (1) +#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9) +#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10) + +// Bootloader configuration (only needed if Mboot is used) +#define MBOOT_I2C_PERIPH_ID 1 +#define MBOOT_I2C_SCL (pin_B8) +#define MBOOT_I2C_SDA (pin_B9) +#define MBOOT_I2C_ALTFUNC (4) diff --git a/ports/stm32/boards/NADHAT_PYBF405/mpconfigboard.mk b/ports/stm32/boards/NADHAT_PYBF405/mpconfigboard.mk new file mode 100644 index 000000000..a4430cc1d --- /dev/null +++ b/ports/stm32/boards/NADHAT_PYBF405/mpconfigboard.mk @@ -0,0 +1,13 @@ +MCU_SERIES = f4 +CMSIS_MCU = STM32F405xx +AF_FILE = boards/stm32f405_af.csv +ifeq ($(USE_MBOOT),1) +# When using Mboot all the text goes together after the filesystem +LD_FILES = boards/stm32f405.ld boards/common_blifs.ld +TEXT0_ADDR = 0x08020000 +else +# When not using Mboot the ISR text goes first, then the rest after the filesystem +LD_FILES = boards/stm32f405.ld boards/common_ifs.ld +TEXT0_ADDR = 0x08000000 +TEXT1_ADDR = 0x08020000 +endif diff --git a/ports/stm32/boards/NADHAT_PYBF405/pins.csv b/ports/stm32/boards/NADHAT_PYBF405/pins.csv new file mode 100644 index 000000000..0a030e985 --- /dev/null +++ b/ports/stm32/boards/NADHAT_PYBF405/pins.csv @@ -0,0 +1,58 @@ +X1,PA0 +X2,PA1 +X3,PA2 +X4,PA3 +X5,PA4 +X6,PA5 +X7,PA6 +X8,PA7 +X9,PB6 +X10,PB7 +X11,PC4 +X12,PC5 +X13,Reset +X14,GND +X15,3.3V +X16,VIN +X17,PB3 +X18,PC13 +X19,PC0 +X20,PC1 +X21,PC2 +X22,PC3 +X23,A3.3V +X24,AGND +Y1,PC6 +Y2,PC7 +Y3,PB8 +Y4,PB9 +Y5,PB12 +Y6,PB13 +Y7,PB14 +Y8,PB15 +Y9,PB10 +Y10,PB11 +Y11,PB0 +Y12,PB1 +Y13,PB2 +Y14,GND +Y15,3.3V +Y16,VIN +SW,PB3 +LED_RED,PA13 +LED_GREEN,PA14 +LED_YELLOW,PA15 +LED_BLUE,PB4 +NC,PB5 +SD_D0,PC8 +SD_D1,PC9 +SD_D2,PC10 +SD_D3,PC11 +SD_CMD,PD2 +SD_CK,PC12 +SD,PA8 +SD_SW,PA8 +USB_VBUS,PA9 +USB_ID,PA10 +USB_DM,PA11 +USB_DP,PA12 diff --git a/ports/stm32/boards/NADHAT_PYBF405/stm32f4xx_hal_conf.h b/ports/stm32/boards/NADHAT_PYBF405/stm32f4xx_hal_conf.h new file mode 100644 index 000000000..7d6344f0a --- /dev/null +++ b/ports/stm32/boards/NADHAT_PYBF405/stm32f4xx_hal_conf.h @@ -0,0 +1,19 @@ +/* This file is part of the MicroPython project, http://micropython.org/ + * The MIT License (MIT) + * Copyright (c) 2019 Damien P. George + */ +#ifndef MICROPY_INCLUDED_STM32F4XX_HAL_CONF_H +#define MICROPY_INCLUDED_STM32F4XX_HAL_CONF_H + +#include "boards/stm32f4xx_hal_conf_base.h" + +// Oscillator values in Hz +#define HSE_VALUE (16000000) +#define LSE_VALUE (32768) +#define EXTERNAL_CLOCK_VALUE (12288000) + +// Oscillator timeouts in ms +#define HSE_STARTUP_TIMEOUT (100) +#define LSE_STARTUP_TIMEOUT (5000) + +#endif // MICROPY_INCLUDED_STM32F4XX_HAL_CONF_H |