diff options
4 files changed, 205 insertions, 0 deletions
diff --git a/ports/stm32/boards/MIKROE_CLICKER2_STM32/mpconfigboard.h b/ports/stm32/boards/MIKROE_CLICKER2_STM32/mpconfigboard.h new file mode 100644 index 000000000..eb622cd29 --- /dev/null +++ b/ports/stm32/boards/MIKROE_CLICKER2_STM32/mpconfigboard.h @@ -0,0 +1,85 @@ +#define MICROPY_HW_BOARD_NAME "MIKROE_CLICKER2_STM32" +#define MICROPY_HW_MCU_NAME "STM32F407" + +#define MICROPY_HW_HAS_SWITCH (1) +#define MICROPY_HW_HAS_FLASH (1) +#define MICROPY_HW_ENABLE_RNG (1) +#define MICROPY_HW_ENABLE_RTC (1) +#define MICROPY_HW_ENABLE_DAC (1) +#define MICROPY_HW_ENABLE_USB (1) + +// HSE is 25MHz +#define MICROPY_HW_CLK_PLLM (25) +#define MICROPY_HW_CLK_PLLN (336) +#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) +#define MICROPY_HW_CLK_PLLQ (7) +#define MICROPY_HW_CLK_LAST_FREQ (1) + +// The board has a 32kHz crystal for the RTC +#define MICROPY_HW_RTC_USE_LSE (1) +#define MICROPY_HW_RTC_USE_US (0) +#define MICROPY_HW_RTC_USE_CALOUT (0) // turn on/off PC13 512Hz output + +// UART config +// mikroBUS slot 1 +#define MICROPY_HW_UART2_NAME "SLOT1" +#define MICROPY_HW_UART2_TX (pin_D5) +#define MICROPY_HW_UART2_RX (pin_D6) +// mikroBUS slot 2 +#define MICROPY_HW_UART3_NAME "SLOT2" +#define MICROPY_HW_UART3_TX (pin_D8) +#define MICROPY_HW_UART3_RX (pin_D9) +// HDR2 +#define MICROPY_HW_UART4_NAME "HDR2" +#define MICROPY_HW_UART4_TX (pin_A0) +#define MICROPY_HW_UART4_RX (pin_A1) + +// I2C buses +// mikroBUS slot 2 / HDR2 +#define MICROPY_HW_I2C2_NAME "SLOT2" +#define MICROPY_HW_I2C2_SCL (pin_B10) +#define MICROPY_HW_I2C2_SDA (pin_B11) +// mikroBUS slot 1 +#define MICROPY_HW_I2C3_NAME "SLOT1" +#define MICROPY_HW_I2C3_SCL (pin_A8) +#define MICROPY_HW_I2C3_SDA (pin_C9) + +// SPI buses +// mikroBUS slot 2 / HDR1 +#define MICROPY_HW_SPI2_NAME "SLOT2" +#define MICROPY_HW_SPI2_NSS (pin_E11) +#define MICROPY_HW_SPI2_SCK (pin_B13) +#define MICROPY_HW_SPI2_MISO (pin_B14) +#define MICROPY_HW_SPI2_MOSI (pin_B15) +// mikroBUS slot 1 +#define MICROPY_HW_SPI3_NAME "SLOT1" +#define MICROPY_HW_SPI3_NSS (pin_E8) +#define MICROPY_HW_SPI3_SCK (pin_C10) +#define MICROPY_HW_SPI3_MISO (pin_C11) +#define MICROPY_HW_SPI3_MOSI (pin_C12) + +// USRSW is pulled high; pressing the button makes the input go low +#define MICROPY_HW_USRSW_PIN (pin_E0) +#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) +#define MICROPY_HW_USRSW_PRESSED (0) + +// LEDs +#define MICROPY_HW_LED1 (pin_E12) // red +#define MICROPY_HW_LED2 (pin_E15) // red +#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) +#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) + +// USB config +#define MICROPY_HW_USB_FS (1) +#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9) + +// Bootloader configuration (only needed if Mboot is used) +#define MBOOT_I2C_PERIPH_ID 2 +#define MBOOT_I2C_SCL (pin_B10) +#define MBOOT_I2C_SDA (pin_B11) +#define MBOOT_I2C_ALTFUNC (4) +#define MBOOT_BOOTPIN_PIN (pin_A10) +#define MBOOT_BOOTPIN_PULL (MP_HAL_PIN_PULL_NONE) +#define MBOOT_BOOTPIN_ACTIVE (0) +#define MBOOT_FSLOAD (1) diff --git a/ports/stm32/boards/MIKROE_CLICKER2_STM32/mpconfigboard.mk b/ports/stm32/boards/MIKROE_CLICKER2_STM32/mpconfigboard.mk new file mode 100644 index 000000000..aa52f2116 --- /dev/null +++ b/ports/stm32/boards/MIKROE_CLICKER2_STM32/mpconfigboard.mk @@ -0,0 +1,13 @@ +MCU_SERIES = f4 +CMSIS_MCU = STM32F407xx +AF_FILE = boards/stm32f405_af.csv +ifeq ($(USE_MBOOT),1) +# When using Mboot all the text goes together after the filesystem +LD_FILES = boards/stm32f405.ld boards/common_blifs.ld +TEXT0_ADDR = 0x08020000 +else +# When not using Mboot the ISR text goes first, then the rest after the filesystem +LD_FILES = boards/stm32f405.ld boards/common_ifs.ld +TEXT0_ADDR = 0x08000000 +TEXT1_ADDR = 0x08020000 +endif diff --git a/ports/stm32/boards/MIKROE_CLICKER2_STM32/pins.csv b/ports/stm32/boards/MIKROE_CLICKER2_STM32/pins.csv new file mode 100644 index 000000000..09e1ccfb4 --- /dev/null +++ b/ports/stm32/boards/MIKROE_CLICKER2_STM32/pins.csv @@ -0,0 +1,88 @@ +MB1_AN,PA2 +MB1_RST,PE7 +MB1_CS,PE8 +MB1_SCK,PC10 +MB1_MISO,PC11 +MB1_MOSI,PC12 +MB1_PWM,PE9 +MB1_INT,PE10 +MB1_RX,PD6 +MB1_TX,PD5 +MB1_SCL,PA8 +MB1_SDA,PC9 +MB2_AN,PA3 +MB2_RST,PE13 +MB2_CS,PE11 +MB2_SCK,PB13 +MB2_MISO,PB14 +MB2_MOSI,PB15 +MB2_PWM,PD12 +MB2_INT,PE14 +MB2_RX,PD9 +MB2_TX,PD8 +MB2_SCL,PB10 +MB2_SDA,PB11 +PIN1,VSYS +PIN2,GND +PIN3,PC0 +PIN4,PC1 +PIN5,PC2 +PIN6,PC3 +PIN7,PB1 +PIN8,PA4 +PIN9,PC4 +PIN10,PD3 +PIN11,PD1 +PIN12,PD2 +PIN13,PD0 +PIN14,PC8 +PIN15,PD15 +PIN16,PD14 +PIN17,PD13 +PIN18,PB7 +PIN19,PC7 +PIN20,PD11 +PIN21,PD10 +PIN22,PB13 +PIN23,PB14 +PIN24,PB15 +PIN25,3.3V +PIN26,GND +PIN27,RST +PIN28,GND +PIN30,NC +PIN31,PB9 +PIN32,PB8 +PIN33,PE5 +PIN34,PB0 +PIN35,PA5 +PIN36,PA6 +PIN37,PA7 +PIN38,PE1 +PIN39,PE2 +PIN40,PE3 +PIN41,PE4 +PIN42,PE6 +PIN43,PB6 +PIN44,PB5 +PIN45,PD7 +PIN46,PC13 +PIN47,PA1 +PIN48,PA0 +PIN49,PB10 +PIN50,PB11 +PIN51,3.3V +PIN52,GND +OSC32_OUT,PC15 +OSC32_IN,PC14 +VSENSE,PC5 +SENSEL,PB12 +FAULT,PC6 +BATSTAT,PD4 +LD1,PE12 +LD2,PE15 +T2,PE0 +T3,PA10 +USB_VBUS,PA9 +USB_DM,PA11 +USB_DP,PA12
\ No newline at end of file diff --git a/ports/stm32/boards/MIKROE_CLICKER2_STM32/stm32f4xx_hal_conf.h b/ports/stm32/boards/MIKROE_CLICKER2_STM32/stm32f4xx_hal_conf.h new file mode 100644 index 000000000..f186d5a29 --- /dev/null +++ b/ports/stm32/boards/MIKROE_CLICKER2_STM32/stm32f4xx_hal_conf.h @@ -0,0 +1,19 @@ +/* This file is part of the MicroPython project, http://micropython.org/ + * The MIT License (MIT) + * Copyright (c) 2019 Damien P. George + */ +#ifndef MICROPY_INCLUDED_STM32F4XX_HAL_CONF_H +#define MICROPY_INCLUDED_STM32F4XX_HAL_CONF_H + +#include "boards/stm32f4xx_hal_conf_base.h" + +// Oscillator values in Hz +#define HSE_VALUE (25000000) +#define LSE_VALUE (32768) +#define EXTERNAL_CLOCK_VALUE (12288000) + +// Oscillator timeouts in ms +#define HSE_STARTUP_TIMEOUT (100) +#define LSE_STARTUP_TIMEOUT (5000) + +#endif // MICROPY_INCLUDED_STM32F4XX_HAL_CONF_H |