blob: 44fb22161084980ebb3ee856d8e5718b8e7e2c47 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
|
#define MICROPY_HW_BOARD_NAME "PYBv3"
#define MICROPY_HW_MCU_NAME "STM32F405RG"
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_HAS_SDCARD (1)
#define MICROPY_HW_HAS_MMA7660 (1)
#define MICROPY_HW_HAS_LIS3DSH (0)
#define MICROPY_HW_HAS_LCD (0)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_TIMER (1)
#define MICROPY_HW_ENABLE_SERVO (1)
#define MICROPY_HW_ENABLE_DAC (1)
#define MICROPY_HW_ENABLE_CAN (1)
// HSE is 8MHz
#define MICROPY_HW_CLK_PLLM (8)
#define MICROPY_HW_CLK_PLLN (336)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (7)
// The pyboard has a 32kHz crystal for the RTC
#define MICROPY_HW_RTC_USE_LSE (1)
// UART config
#define MICROPY_HW_UART1_PORT (GPIOA)
#define MICROPY_HW_UART1_PINS (GPIO_PIN_9 | GPIO_PIN_10)
#define MICROPY_HW_UART2_PORT (GPIOA)
#define MICROPY_HW_UART2_PINS (GPIO_PIN_2 | GPIO_PIN_3)
#define MICROPY_HW_UART2_RTS (GPIO_PIN_1)
#define MICROPY_HW_UART2_CTS (GPIO_PIN_0)
#define MICROPY_HW_UART3_PORT (GPIOB)
#define MICROPY_HW_UART3_PINS (GPIO_PIN_10 | GPIO_PIN_11)
#define MICROPY_HW_UART3_RTS (GPIO_PIN_14)
#define MICROPY_HW_UART3_CTS (GPIO_PIN_13)
#define MICROPY_HW_UART4_PORT (GPIOA)
#define MICROPY_HW_UART4_PINS (GPIO_PIN_0 | GPIO_PIN_1)
#define MICROPY_HW_UART6_PORT (GPIOC)
#define MICROPY_HW_UART6_PINS (GPIO_PIN_6 | GPIO_PIN_7)
// X-skin: X9=PB6=SCL, X10=PB7=SDA
#define MICROPY_HW_I2C1_SCL (pin_B6)
#define MICROPY_HW_I2C1_SDA (pin_B7)
// Y-skin: Y9=PB10=SCL, Y10=PB11=SDA
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)
// SPI busses
#define MICROPY_HW_SPI1_NAME "X"
#define MICROPY_HW_SPI1_NSS (pin_A4) // X5
#define MICROPY_HW_SPI1_SCK (pin_A5) // X6
#define MICROPY_HW_SPI1_MISO (pin_A6) // X7
#define MICROPY_HW_SPI1_MOSI (pin_A7) // X8
#define MICROPY_HW_SPI2_NAME "Y"
#define MICROPY_HW_SPI2_NSS (pin_B12) // Y5
#define MICROPY_HW_SPI2_SCK (pin_B13) // Y6
#define MICROPY_HW_SPI2_MISO (pin_B14) // Y7
#define MICROPY_HW_SPI2_MOSI (pin_B15) // Y8
// USRSW has no pullup or pulldown, and pressing the switch makes the input go low
#define MICROPY_HW_USRSW_PIN (pin_A13)
#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
#define MICROPY_HW_USRSW_PRESSED (0)
// LEDs
#define MICROPY_HW_LED_INVERTED (1) // LEDs are on when pin is driven low
#define MICROPY_HW_LED1 (pin_A8) // R1 - red
#define MICROPY_HW_LED2 (pin_A10) // R2 - red
#define MICROPY_HW_LED3 (pin_C4) // G1 - green
#define MICROPY_HW_LED4 (pin_C5) // G2 - green
#define MICROPY_HW_LED1_PWM { TIM1, 1, TIM_CHANNEL_1, GPIO_AF1_TIM1 }
#define MICROPY_HW_LED2_PWM { TIM1, 1, TIM_CHANNEL_3, GPIO_AF1_TIM1 }
#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP)
#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRH = pin->pin_mask)
#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRL = pin->pin_mask)
// SD card detect switch
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_C13)
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLDOWN)
#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_SET)
// USB VBUS detect pin
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
// MMA accelerometer config
#define MICROPY_HW_MMA_AVDD_PIN (pin_B5)
|
