ide core updates, and addition of ide-iops.c

1 files changed, 951 insertions, 480 deletions

diff --git a/include/linux/ide.h b/include/linux/ide.h
index 1843237adf4a..32409745ded5 100644
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -3,7 +3,7 @@
 /*
  *  linux/include/linux/ide.h
  *
- *  Copyright (C) 1994-1998  Linus Torvalds & authors
+ *  Copyright (C) 1994-2002  Linus Torvalds & authors
  */
 
 #include <linux/config.h>
@@ -14,18 +14,14 @@
 #include <linux/blkdev.h>
 #include <linux/proc_fs.h>
 #include <linux/devfs_fs_kernel.h>
+#include <linux/interrupt.h>
+#include <linux/bitops.h>
 #include <linux/bio.h>
 #include <asm/byteorder.h>
 #include <asm/system.h>
 #include <asm/hdreg.h>
 #include <asm/io.h>
 
-#ifdef CONFIG_BLK_DEV_IDEDMA_TIMEOUT
-#  define __IDEDMA_TIMEOUT
-#else /* CONFIG_BLK_DEV_IDEDMA_TIMEOUT */
-#  undef __IDEDMA_TIMEOUT
-#endif /* CONFIG_BLK_DEV_IDEDMA_TIMEOUT */
-
 /*
  * This is the multiple IDE interface driver, as evolved from hd.c.
  * It supports up to four IDE interfaces, on one or more IRQs (usually 14 & 15).
@@ -42,7 +38,7 @@
  *
  * REALLY_SLOW_IO can be defined in ide.c and ide-cd.c, if necessary
  */
-#undef REALLY_FAST_IO			/* define if ide ports are perfect */
+#define REALLY_FAST_IO			/* define if ide ports are perfect */
 #define INITIAL_MULT_COUNT	0	/* off=0; on=2,4,8,16,32, etc.. */
 
 #ifndef SUPPORT_SLOW_DATA_PORTS		/* 1 to support slow data ports */
@@ -170,9 +166,6 @@ typedef unsigned char	byte;	/* used everywhere */
 #define IDE_BCOUNTL_REG		IDE_LCYL_REG
 #define IDE_BCOUNTH_REG		IDE_HCYL_REG
 
-#define GET_ERR()		IN_BYTE(IDE_ERROR_REG)
-#define GET_STAT()		IN_BYTE(IDE_STATUS_REG)
-#define GET_ALTSTAT()		IN_BYTE(IDE_CONTROL_REG)
 #define OK_STAT(stat,good,bad)	(((stat)&((good)|(bad)))==(good))
 #define BAD_R_STAT		(BUSY_STAT   | ERR_STAT)
 #define BAD_W_STAT		(BAD_R_STAT  | WRERR_STAT)
@@ -180,6 +173,43 @@ typedef unsigned char	byte;	/* used everywhere */
 #define DRIVE_READY		(READY_STAT  | SEEK_STAT)
 #define DATA_READY		(DRQ_STAT)
 
+#define BAD_CRC			(ABRT_ERR    | ICRC_ERR)
+
+#define SATA_NR_PORTS		(3)	/* 16 possible ?? */
+
+#define SATA_STATUS_OFFSET	(0)
+#define SATA_STATUS_REG		(HWIF(drive)->sata_scr[SATA_STATUS_OFFSET])
+#define SATA_ERROR_OFFSET	(1)
+#define SATA_ERROR_REG		(HWIF(drive)->sata_scr[SATA_ERROR_OFFSET])
+#define SATA_CONTROL_OFFSET	(2)
+#define SATA_CONTROL_REG	(HWIF(drive)->sata_scr[SATA_CONTROL_OFFSET])
+
+#define SATA_MISC_OFFSET	(0)
+#define SATA_MISC_REG		(HWIF(drive)->sata_misc[SATA_MISC_OFFSET])
+#define SATA_PHY_OFFSET		(1)
+#define SATA_PHY_REG		(HWIF(drive)->sata_misc[SATA_PHY_OFFSET])
+#define SATA_IEN_OFFSET		(2)
+#define SATA_IEN_REG		(HWIF(drive)->sata_misc[SATA_IEN_OFFSET])
+
+/*
+ * Our Physical Region Descriptor (PRD) table should be large enough
+ * to handle the biggest I/O request we are likely to see.  Since requests
+ * can have no more than 256 sectors, and since the typical blocksize is
+ * two or more sectors, we could get by with a limit of 128 entries here for
+ * the usual worst case.  Most requests seem to include some contiguous blocks,
+ * further reducing the number of table entries required.
+ *
+ * The driver reverts to PIO mode for individual requests that exceed
+ * this limit (possible with 512 byte blocksizes, eg. MSDOS f/s), so handling
+ * 100% of all crazy scenarios here is not necessary.
+ *
+ * As it turns out though, we must allocate a full 4KB page for this,
+ * so the two PRD tables (ide0 & ide1) will each get half of that,
+ * allowing each to have about 256 entries (8 bytes each) from this.
+ */
+#define PRD_BYTES       8
+#define PRD_ENTRIES     (PAGE_SIZE / (2 * PRD_BYTES))
+
 /*
  * sector count bits
  */
@@ -215,21 +245,12 @@ typedef unsigned char	byte;	/* used everywhere */
 #define PARTN_BITS	6	/* number of minor dev bits for partitions */
 #define PARTN_MASK	((1<<PARTN_BITS)-1)	/* a useful bit mask */
 #define MAX_DRIVES	2	/* per interface; 2 assumed by lots of code */
-#define CASCADE_DRIVES	8	/* per interface; 8|2 assumed by lots of code */
 #define SECTOR_SIZE	512
 #define SECTOR_WORDS	(SECTOR_SIZE / 4)	/* number of 32bit words per sector */
 #define IDE_LARGE_SEEK(b1,b2,t)	(((b1) > (b2) + (t)) || ((b2) > (b1) + (t)))
 #define IDE_MIN(a,b)	((a)<(b) ? (a):(b))
 #define IDE_MAX(a,b)	((a)>(b) ? (a):(b))
 
-#ifndef SPLIT_WORD
-#  define SPLIT_WORD(W,HB,LB) ((HB)=(W>>8), (LB)=(W-((W>>8)<<8)))
-#endif
-#ifndef MAKE_WORD
-#  define MAKE_WORD(W,HB,LB) ((W)=((HB<<8)+LB))
-#endif
-
-
 /*
  * Timeouts for various operations:
  */
@@ -244,39 +265,6 @@ typedef unsigned char	byte;	/* used everywhere */
 #define WAIT_CMD	(10*HZ)	/* 10sec  - maximum wait for an IRQ to happen */
 #define WAIT_MIN_SLEEP	(2*HZ/100)	/* 20msec - minimum sleep time */
 
-#define SELECT_DRIVE(hwif,drive)				\
-{								\
-	if (hwif->selectproc)					\
-		hwif->selectproc(drive);			\
-	OUT_BYTE((drive)->select.all, hwif->io_ports[IDE_SELECT_OFFSET]); \
-}
-
-#define SELECT_INTERRUPT(hwif,drive)				\
-{								\
-	if (hwif->intrproc)					\
-		hwif->intrproc(drive);				\
-	else							\
-		OUT_BYTE((drive)->ctl|2, hwif->io_ports[IDE_CONTROL_OFFSET]);	\
-}
-
-#define SELECT_MASK(hwif,drive,mask)				\
-{								\
-	if (hwif->maskproc)					\
-		hwif->maskproc(drive,mask);			\
-}
-
-#define SELECT_READ_WRITE(hwif,drive,func)			\
-{								\
-	if (hwif->rwproc)					\
-		hwif->rwproc(drive,func);			\
-}
-
-#define QUIRK_LIST(hwif,drive)					\
-{								\
-	if (hwif->quirkproc)					\
-		(drive)->quirk_list = hwif->quirkproc(drive);	\
-}
-
 #define HOST(hwif,chipset)					\
 {								\
 	return ((hwif)->chipset == chipset) ? 1 : 0;		\
@@ -304,9 +292,34 @@ typedef enum {	ide_unknown,	ide_generic,	ide_pci,
 		ide_qd65xx,	ide_umc8672,	ide_ht6560b,
 		ide_pdc4030,	ide_rz1000,	ide_trm290,
 		ide_cmd646,	ide_cy82c693,	ide_4drives,
-		ide_pmac,	ide_etrax100
+		ide_pmac,	ide_etrax100,	ide_acorn
 } hwif_chipset_t;
 
+typedef struct ide_io_ops_s {
+	/* insert io operations here! */
+	void (*OUTB)(u8 addr, u32 port);
+	void (*OUTW)(u16 addr, u32 port);
+	void (*OUTL)(u32 addr, u32 port);
+	void (*OUTBP)(u8 addr, u32 port);
+	void (*OUTWP)(u16 addr, u32 port);
+	void (*OUTLP)(u32 addr, u32 port);
+	void (*OUTSW)(u32 port, void *addr, u32 count);
+	void (*OUTSWP)(u32 port, void *addr, u32 count);
+	void (*OUTSL)(u32 port, void *addr, u32 count);
+	void (*OUTSLP)(u32 port, void *addr, u32 count);
+
+	u8  (*INB)(u32 port);
+	u16 (*INW)(u32 port);
+	u32 (*INL)(u32 port);
+	u8  (*INBP)(u32 port);
+	u16 (*INWP)(u32 port);
+	u32 (*INLP)(u32 port);
+	void (*INSW)(u32 port, void *addr, u32 count);
+	void (*INSWP)(u32 port, void *addr, u32 count);
+	void (*INSL)(u32 port, void *addr, u32 count);
+	void (*INSLP)(u32 port, void *addr, u32 count);
+} ide_io_ops_t;
+
 /*
  * Structure to hold all information about the location of this port
  */
@@ -317,6 +330,11 @@ typedef struct hw_regs_s {
 	ide_ack_intr_t	*ack_intr;		/* acknowledge interrupt */
 	void		*priv;			/* interface specific data */
 	hwif_chipset_t  chipset;
+#if 0
+	ide_io_ops_t	*iops;			/* */
+#endif
+	sata_ioreg_t	sata_scr[SATA_NR_PORTS];
+	sata_ioreg_t	sata_misc[SATA_NR_PORTS];
 } hw_regs_t;
 
 /*
@@ -333,10 +351,27 @@ void ide_setup_ports(	hw_regs_t *hw,
 			ide_ioreg_t ctrl,
 			ide_ioreg_t intr,
 			ide_ack_intr_t *ack_intr,
+#if 0
+			ide_io_ops_t *iops,
+#endif
 			int irq);
 
 #include <asm/ide.h>
 
+/* Currently only m68k, apus and m8xx need it */
+#ifdef IDE_ARCH_ACK_INTR
+extern int ide_irq_lock;
+# define ide_ack_intr(hwif) (hwif->hw.ack_intr ? hwif->hw.ack_intr(hwif) : 1)
+#else
+# define ide_ack_intr(hwif) (1)
+#endif
+
+/* Currently only Atari needs it */
+#ifndef IDE_ARCH_LOCK
+# define ide_release_lock(lock)			do {} while (0)
+# define ide_get_lock(lock, hdlr, data)		do {} while (0)
+#endif /* IDE_ARCH_LOCK */
+
 /*
  * If the arch-dependant ide.h did not declare/define any OUT_BYTE
  * or IN_BYTE functions, we make some defaults here.
@@ -346,20 +381,30 @@ void ide_setup_ports(	hw_regs_t *hw,
 # ifdef REALLY_FAST_IO
 #  define OUT_BYTE(b,p)		outb((b),(p))
 #  define OUT_WORD(w,p)		outw((w),(p))
+#  define OUT_LONG(l,p)		outl((l),(p))
 # else
 #  define OUT_BYTE(b,p)		outb_p((b),(p))
 #  define OUT_WORD(w,p)		outw_p((w),(p))
+#  define OUT_LONG(l,p)		outl_p((l),(p))
 # endif
+# define OUT_BYTE_P(b,p)	outb_p((b),(p))
+# define OUT_WORD_P(w,p)	outw_p((w),(p))
+# define OUT_LONG_P(l,p)	outl_p((l),(p))
 #endif
 
 #ifndef HAVE_ARCH_IN_BYTE
 # ifdef REALLY_FAST_IO
-#  define IN_BYTE(p)		(byte)inb(p)
-#  define IN_WORD(p)		(short)inw(p)
+#  define IN_BYTE(p)		(u8) inb(p)
+#  define IN_WORD(p)		(u16) inw(p)
+#  define IN_LONG(p)		(u32) inl(p)
 # else
-#  define IN_BYTE(p)		(byte)inb_p(p)
-#  define IN_WORD(p)		(short)inw_p(p)
+#  define IN_BYTE(p)		(u8) inb_p(p)
+#  define IN_WORD(p)		(u16) inw_p(p)
+#  define IN_LONG(p)		(u32) inl_p(p)
 # endif
+# define IN_BYTE_P(p)		(u8) inb_p(p)
+# define IN_WORD_P(p)		(u16) inw_p(p)
+# define IN_LONG_P(p)		(u32) inl_p(p)
 #endif
 
 /*
@@ -373,201 +418,453 @@ void ide_setup_ports(	hw_regs_t *hw,
 #define ide_tape	0x1
 #define ide_floppy	0x0
 
+/*
+ * Special Driver Flags
+ *
+ * set_geometry	: respecify drive geometry
+ * recalibrate	: seek to cyl 0
+ * set_multmode	: set multmode count
+ * set_tune	: tune interface for drive
+ * serviced	: service command
+ * reserved	: unused
+ */
 typedef union {
-	unsigned all			: 8;	/* all of the bits together */
+	unsigned all			: 8;
 	struct {
 #if defined(__LITTLE_ENDIAN_BITFIELD)
-		unsigned set_geometry	: 1;	/* respecify drive geometry */
-		unsigned recalibrate	: 1;	/* seek to cyl 0      */
-		unsigned set_multmode	: 1;	/* set multmode count */
-		unsigned set_tune	: 1;	/* tune interface for drive */
-		unsigned serviced	: 1;	/* service command */
-		unsigned reserved	: 3;	/* unused */
+		unsigned set_geometry	: 1;
+		unsigned recalibrate	: 1;
+		unsigned set_multmode	: 1;
+		unsigned set_tune	: 1;
+		unsigned serviced	: 1;
+		unsigned reserved	: 3;
 #elif defined(__BIG_ENDIAN_BITFIELD)
-		unsigned reserved	: 3;	/* unused */
-		unsigned serviced	: 1;	/* service command */
-		unsigned set_tune	: 1;	/* tune interface for drive */
-		unsigned set_multmode	: 1;	/* set multmode count */
-		unsigned recalibrate	: 1;	/* seek to cyl 0      */
-		unsigned set_geometry	: 1;	/* respecify drive geometry */
+		unsigned reserved	: 3;
+		unsigned serviced	: 1;
+		unsigned set_tune	: 1;
+		unsigned set_multmode	: 1;
+		unsigned recalibrate	: 1;
+		unsigned set_geometry	: 1;
 #else
 #error "Please fix <asm/byteorder.h>"
 #endif
 	} b;
 } special_t;
 
+/*
+ * ATA DATA Register Special.
+ * ATA NSECTOR Count Register().
+ * ATAPI Byte Count Register.
+ * Channel index ordering pairs.
+ */
+typedef union {
+	unsigned all			:16;
+	struct {
+#if defined(__LITTLE_ENDIAN_BITFIELD)
+		unsigned low		:8;	/* LSB */
+		unsigned high		:8;	/* MSB */
+#elif defined(__BIG_ENDIAN_BITFIELD)
+		unsigned high		:8;	/* MSB */
+		unsigned low		:8;	/* LSB */
+#else
+#error "Please fix <asm/byteorder.h>"
+#endif
+	} b;
+} ata_nsector_t, ata_data_t, atapi_bcount_t, ata_index_t;
+
+/*
+ * ATA-IDE Error Register
+ *
+ * mark		: Bad address mark
+ * tzero	: Couldn't find track 0
+ * abrt		: Aborted Command
+ * mcr		: Media Change Request
+ * id		: ID field not found
+ * mce		: Media Change Event
+ * ecc		: Uncorrectable ECC error
+ * bdd		: dual meaing
+ */
 typedef union {
-	unsigned all			: 8;	/* all of the bits together */
+	unsigned all			:8;
 	struct {
 #if defined(__LITTLE_ENDIAN_BITFIELD)
-		unsigned head		: 4;	/* always zeros here */
-		unsigned unit		: 1;	/* drive select number: 0/1 */
-		unsigned bit5		: 1;	/* always 1 */
-		unsigned lba		: 1;	/* using LBA instead of CHS */
-		unsigned bit7		: 1;	/* always 1 */
+		unsigned mark		:1;
+		unsigned tzero		:1;
+		unsigned abrt		:1;
+		unsigned mcr		:1;
+		unsigned id		:1;
+		unsigned mce		:1;
+		unsigned ecc		:1;
+		unsigned bdd		:1;
 #elif defined(__BIG_ENDIAN_BITFIELD)
-		unsigned bit7		: 1;	/* always 1 */
-		unsigned lba		: 1;	/* using LBA instead of CHS */
-		unsigned bit5		: 1;	/* always 1 */
-		unsigned unit		: 1;	/* drive select number: 0/1 */
-		unsigned head		: 4;	/* always zeros here */
+		unsigned bdd		:1;
+		unsigned ecc		:1;
+		unsigned mce		:1;
+		unsigned id		:1;
+		unsigned mcr		:1;
+		unsigned abrt		:1;
+		unsigned tzero		:1;
+		unsigned mark		:1;
 #else
 #error "Please fix <asm/byteorder.h>"
 #endif
 	} b;
-} select_t;
+} ata_error_t;
 
+/*
+ * ATA-IDE Select Register, aka Device-Head
+ *
+ * head		: always zeros here
+ * unit		: drive select number: 0/1
+ * bit5		: always 1
+ * lba		: using LBA instead of CHS
+ * bit7		: always 1
+ */
 typedef union {
-	unsigned all			: 8;	/* all of the bits together */
+	unsigned all			: 8;
+	struct {
+#if defined(__LITTLE_ENDIAN_BITFIELD)
+		unsigned head		: 4;
+		unsigned unit		: 1;
+		unsigned bit5		: 1;
+		unsigned lba		: 1;
+		unsigned bit7		: 1;
+#elif defined(__BIG_ENDIAN_BITFIELD)
+		unsigned bit7		: 1;
+		unsigned lba		: 1;
+		unsigned bit5		: 1;
+		unsigned unit		: 1;
+		unsigned head		: 4;
+#else
+#error "Please fix <asm/byteorder.h>"
+#endif
+	} b;
+} select_t, ata_select_t;
+
+/*
+ * The ATA-IDE Status Register.
+ * The ATAPI Status Register.
+ *
+ * check	: Error occurred
+ * idx		: Index Error
+ * corr		: Correctable error occurred
+ * drq		: Data is request by the device
+ * dsc		: Disk Seek Complete			: ata
+ *		: Media access command finished		: atapi
+ * df		: Device Fault				: ata
+ *		: Reserved				: atapi
+ * drdy		: Ready, Command Mode Capable		: ata
+ *		: Ignored for ATAPI commands		: atapi
+ * bsy		: Disk is Busy
+ *		: The device has access to the command block
+ */
+typedef union {
+	unsigned all			:8;
+	struct {
+#if defined(__LITTLE_ENDIAN_BITFIELD)
+		unsigned check		:1;
+		unsigned idx		:1;
+		unsigned corr		:1;
+		unsigned drq		:1;
+		unsigned dsc		:1;
+		unsigned df		:1;
+		unsigned drdy		:1;
+		unsigned bsy		:1;
+#elif defined(__BIG_ENDIAN_BITFIELD)
+		unsigned bsy		:1;
+		unsigned drdy		:1;
+		unsigned df		:1;
+		unsigned dsc		:1;
+		unsigned drq		:1;
+		unsigned corr           :1;
+		unsigned idx		:1;
+		unsigned check		:1;
+#else
+#error "Please fix <asm/byteorder.h>"
+#endif
+	} b;
+} ata_status_t, atapi_status_t;
+
+/*
+ * ATA-IDE Control Register
+ *
+ * bit0		: Should be set to zero
+ * nIEN		: device INTRQ to host
+ * SRST		: host soft reset bit
+ * bit3		: ATA-2 thingy, Should be set to 1
+ * reserved456	: Reserved
+ * HOB		: 48-bit address ordering, High Ordered Bit
+ */
+typedef union {
+	unsigned all			: 8;
 	struct {
 #if defined(__LITTLE_ENDIAN_BITFIELD)
 		unsigned bit0		: 1;
-		unsigned nIEN		: 1;	/* device INTRQ to host */
-		unsigned SRST		: 1;	/* host soft reset bit */
-		unsigned bit3		: 1;	/* ATA-2 thingy */
-		unsigned reserved456    : 3;
-		unsigned HOB            : 1;	/* 48-bit address ordering */
+		unsigned nIEN		: 1;
+		unsigned SRST		: 1;
+		unsigned bit3		: 1;
+		unsigned reserved456	: 3;
+		unsigned HOB		: 1;
 #elif defined(__BIG_ENDIAN_BITFIELD)
-		unsigned HOB		: 1;	/* 48-bit address ordering */
+		unsigned HOB		: 1;
 		unsigned reserved456	: 3;
-		unsigned bit3		: 1;	/* ATA-2 thingy */
-		unsigned SRST		: 1;	/* host soft reset bit */
-		unsigned nIEN		: 1;	/* device INTRQ to host */
+		unsigned bit3		: 1;
+		unsigned SRST		: 1;
+		unsigned nIEN		: 1;
 		unsigned bit0		: 1;
 #else
 #error "Please fix <asm/byteorder.h>"
 #endif
 	} b;
-} control_t;
+} ata_control_t;
 
+/*
+ * ATAPI Feature Register
+ *
+ * dma		: Using DMA or PIO
+ * reserved321	: Reserved
+ * reserved654	: Reserved (Tag Type)
+ * reserved7	: Reserved
+ */
+typedef union {
+	unsigned all			:8;
+	struct {
+#if defined(__LITTLE_ENDIAN_BITFIELD)
+		unsigned dma		:1;
+		unsigned reserved321	:3;
+		unsigned reserved654	:3;
+		unsigned reserved7	:1;
+#elif defined(__BIG_ENDIAN_BITFIELD)
+		unsigned reserved7	:1;
+		unsigned reserved654	:3;
+		unsigned reserved321	:3;
+		unsigned dma		:1;
+#else
+#error "Please fix <asm/byteorder.h>"
+#endif
+	} b;
+} atapi_feature_t;
+
+/*
+ * ATAPI Interrupt Reason Register.
+ *
+ * cod		: Information transferred is command (1) or data (0)
+ * io		: The device requests us to read (1) or write (0)
+ * reserved	: Reserved
+ */
+typedef union {
+	unsigned all			:8;
+	struct {
+#if defined(__LITTLE_ENDIAN_BITFIELD)
+		unsigned cod		:1;
+		unsigned io		:1;
+		unsigned reserved	:6;
+#elif defined(__BIG_ENDIAN_BITFIELD)
+		unsigned reserved	:6;
+		unsigned io		:1;
+		unsigned cod		:1;
+#else
+#error "Please fix <asm/byteorder.h>"
+#endif
+	} b;
+} atapi_ireason_t;
+
+/*
+ * The ATAPI error register.
+ *
+ * ili		: Illegal Length Indication
+ * eom		: End Of Media Detected
+ * abrt		: Aborted command - As defined by ATA
+ * mcr		: Media Change Requested - As defined by ATA
+ * sense_key	: Sense key of the last failed packet command
+ */
+typedef union {
+	unsigned all			:8;
+	struct {
+#if defined(__LITTLE_ENDIAN_BITFIELD)
+		unsigned ili		:1;
+		unsigned eom		:1;
+		unsigned abrt		:1;
+		unsigned mcr		:1;
+		unsigned sense_key	:4;
+#elif defined(__BIG_ENDIAN_BITFIELD)
+		unsigned sense_key	:4;
+		unsigned mcr		:1;
+		unsigned abrt		:1;
+		unsigned eom		:1;
+		unsigned ili		:1;
+#else
+#error "Please fix <asm/byteorder.h>"
+#endif
+	} b;
+} atapi_error_t;
+
+/*
+ * ATAPI floppy Drive Select Register
+ *
+ * sam_lun	: Logical unit number
+ * reserved3	: Reserved
+ * drv		: The responding drive will be drive 0 (0) or drive 1 (1)
+ * one5		: Should be set to 1
+ * reserved6	: Reserved
+ * one7		: Should be set to 1
+ */
+typedef union {
+	unsigned all			:8;
+	struct {
+#if defined(__LITTLE_ENDIAN_BITFIELD)
+		unsigned sam_lun	:3;
+		unsigned reserved3	:1;
+		unsigned drv		:1;
+		unsigned one5		:1;
+		unsigned reserved6	:1;
+		unsigned one7		:1;
+#elif defined(__BIG_ENDIAN_BITFIELD)
+		unsigned one7		:1;
+		unsigned reserved6	:1;
+		unsigned one5		:1;
+		unsigned drv		:1;
+		unsigned reserved3	:1;
+		unsigned sam_lun	:3;
+#else
+#error "Please fix <asm/byteorder.h>"
+#endif
+	} b;
+} atapi_select_t;
 
 struct ide_driver_s;
 struct ide_settings_s;
 
 typedef struct ide_drive_s {
-	request_queue_t		 queue;	/* request queue */
+	char		name[4];	/* drive name, such as "hda" */
+        char            driver_req[10];	/* requests specific driver */
+
+	request_queue_t		queue;	/* request queue */
+
+	struct request		*rq;	/* current request */
 	struct ide_drive_s 	*next;	/* circular list of hwgroup drives */
+	struct ide_driver_s	*driver;/* (ide_driver_t *) */
+	void		*driver_data;	/* extra driver data */
+	struct hd_driveid	*id;	/* drive model identification info */
+	struct proc_dir_entry *proc;	/* /proc/ide/ directory entry */
+	struct ide_settings_s *settings;/* /proc/ide/ drive settings */
+	devfs_handle_t		de;	/* directory for device */
+
+	struct hwif_s		*hwif;	/* actually (ide_hwif_t *) */
+
 	unsigned long sleep;		/* sleep until this time */
 	unsigned long service_start;	/* time we started last request */
 	unsigned long service_time;	/* service time of last request */
 	unsigned long timeout;		/* max time to wait for irq */
+
 	special_t	special;	/* special action flags */
-	byte     keep_settings;		/* restore settings after drive reset */
-	byte     using_dma;		/* disk is using dma for read/write */
-	byte	 retry_pio;		/* retrying dma capable host in pio */
-	byte	 state;			/* retry state */
-	byte     waiting_for_dma;	/* dma currently in progress */
-	byte     unmask;		/* flag: okay to unmask other irqs */
-	byte     slow;			/* flag: slow data port */
-	byte     bswap;			/* flag: byte swap data */
-	byte     dsc_overlap;		/* flag: DSC overlap */
-	byte     nice1;			/* flag: give potential excess bandwidth */
+	select_t	select;		/* basic drive/head select reg value */
+
+	u8	keep_settings;		/* restore settings after drive reset */
+	u8	autodma;		/* device can safely use dma on host */
+	u8	using_dma;		/* disk is using dma for read/write */
+	u8	using_tcq;		/* disk is using queueing */
+	u8	retry_pio;		/* retrying dma capable host in pio */
+	u8	state;			/* retry state */
+	u8	waiting_for_dma;	/* dma currently in progress */
+	u8	unmask;			/* okay to unmask other irqs */
+	u8	slow;			/* slow data port */
+	u8	bswap;			/* byte swap data */
+	u8	dsc_overlap;		/* DSC overlap */
+	u8	nice1;			/* give potential excess bandwidth */
+
 	unsigned present	: 1;	/* drive is physically present */
 	unsigned noprobe 	: 1;	/* from:  hdx=noprobe */
 	unsigned removable	: 1;	/* 1 if need to do check_media_change */
+	unsigned is_flash	: 1;	/* 1 if probed as flash */
 	unsigned forced_geom	: 1;	/* 1 if hdx=c,h,s was given at boot */
 	unsigned no_unmask	: 1;	/* disallow setting unmask bit */
 	unsigned no_io_32bit	: 1;	/* disallow enabling 32bit I/O */
-	unsigned nobios		: 1;	/* flag: do not probe bios for drive */
-	unsigned atapi_overlap	: 1;	/* flag: ATAPI overlap (not supported) */
-	unsigned nice0		: 1;	/* flag: give obvious excess bandwidth */
-	unsigned nice2		: 1;	/* flag: give a share in our own bandwidth */
-	unsigned doorlocking	: 1;	/* flag: for removable only: door lock/unlock works */
+	unsigned nobios		: 1;	/* do not probe bios for drive */
+	unsigned atapi_overlap	: 1;	/* ATAPI overlap (not supported) */
+	unsigned nice0		: 1;	/* give obvious excess bandwidth */
+	unsigned nice2		: 1;	/* give a share in our own bandwidth */
+	unsigned doorlocking	: 1;	/* for removable only: door lock/unlock works */
 	unsigned autotune	: 2;	/* 1=autotune, 2=noautotune, 0=default */
 	unsigned remap_0_to_1	: 2;	/* 0=remap if ezdrive, 1=remap, 2=noremap */
 	unsigned ata_flash	: 1;	/* 1=present, 0=default */
-	unsigned addressing;		/*	: 3;
+	unsigned addressing;		/*      : 3;
 					 *  0=28-bit
 					 *  1=48-bit
 					 *  2=48-bit doing 28-bit
 					 *  3=64-bit
 					 */
-	byte		scsi;		/* 0=default, 1=skip current ide-subdriver for ide-scsi emulation */
-	byte		media;		/* disk, cdrom, tape, floppy, ... */
-	select_t	select;		/* basic drive/head select reg value */
-	byte		ctl;		/* "normal" value for IDE_CONTROL_REG */
-	byte		ready_stat;	/* min status value for drive ready */
-	byte		mult_count;	/* current multiple sector setting */
-	byte 		mult_req;	/* requested multiple sector setting */
-	byte 		tune_req;	/* requested drive tuning setting */
-	byte		io_32bit;	/* 0=16-bit, 1=32-bit, 2/3=32bit+sync */
-	byte		bad_wstat;	/* used for ignoring WRERR_STAT */
-	byte		nowerr;		/* used for ignoring WRERR_STAT */
-	byte		sect0;		/* offset of first sector for DM6:DDO */
-	unsigned int	usage;		/* current "open()" count for drive */
-	byte 		head;		/* "real" number of heads */
-	byte		sect;		/* "real" sectors per track */
-	byte		bios_head;	/* BIOS/fdisk/LILO number of heads */
-	byte		bios_sect;	/* BIOS/fdisk/LILO sectors per track */
+
+	u8	scsi;		/* 0=default, 1=skip current ide-subdriver for ide-scsi emulation */
+        u8	quirk_list;	/* considered quirky, set for a specific host */
+        u8	suspend_reset;	/* drive suspend mode flag, soft-reset recovers */
+        u8	init_speed;	/* transfer rate set at boot */
+        u8	current_speed;	/* current transfer rate set */
+        u8	dn;		/* now wide spread use */
+        u8	wcache;		/* status of write cache */
+	u8	acoustic;	/* acoustic management */
+	u8	media;		/* disk, cdrom, tape, floppy, ... */
+	u8	ctl;		/* "normal" value for IDE_CONTROL_REG */
+	u8	ready_stat;	/* min status value for drive ready */
+	u8	mult_count;	/* current multiple sector setting */
+	u8	mult_req;	/* requested multiple sector setting */
+	u8	tune_req;	/* requested drive tuning setting */
+	u8	io_32bit;	/* 0=16-bit, 1=32-bit, 2/3=32bit+sync */
+	u8	bad_wstat;	/* used for ignoring WRERR_STAT */
+	u8	nowerr;		/* used for ignoring WRERR_STAT */
+	u8	sect0;		/* offset of first sector for DM6:DDO */
+	u8	head;		/* "real" number of heads */
+	u8	sect;		/* "real" sectors per track */
+	u8	bios_head;	/* BIOS/fdisk/LILO number of heads */
+	u8	bios_sect;	/* BIOS/fdisk/LILO sectors per track */
+
 	unsigned int	bios_cyl;	/* BIOS/fdisk/LILO number of cyls */
 	unsigned int	cyl;		/* "real" number of cyls */
-	unsigned long	capacity;	/* total number of sectors */
-	unsigned long long capacity48;	/* total number of sectors */
-	unsigned int	drive_data;	/* for use by tuneproc/selectproc as needed */
-	struct hwif_s	  *hwif;	/* actually (ide_hwif_t *) */
-	struct hd_driveid *id;		/* drive model identification info */
-	char		name[4];	/* drive name, such as "hda" */
-	struct ide_driver_s *driver;	/* (ide_driver_t *) */
-	void		*driver_data;	/* extra driver data */
-	devfs_handle_t	de;		/* directory for device */
-	struct proc_dir_entry *proc;	/* /proc/ide/ directory entry */
-	struct ide_settings_s *settings;	/* /proc/ide/ drive settings */
-	char		driver_req[10];	/* requests specific driver */
+	unsigned int	drive_data;	/* use by tuneproc/selectproc */
+	unsigned int	usage;		/* current "open()" count for drive */
+	unsigned int	failures;	/* current failure count */
+	unsigned int	max_failures;	/* maximum allowed failure count */
+
+	u32		capacity;	/* total number of sectors */
+	u64		capacity48;	/* total number of sectors */
+
 	int		last_lun;	/* last logical unit */
 	int		forced_lun;	/* if hdxlun was given at boot */
 	int		lun;		/* logical unit */
 	int		crc_count;	/* crc counter to reduce drive speed */
-	byte		quirk_list;	/* drive is considered quirky if set for a specific host */
-	byte		suspend_reset;	/* drive suspend mode flag, soft-reset recovers */
-	byte		init_speed;	/* transfer rate set at boot */
-	byte		current_speed;	/* current transfer rate set */
-	byte		dn;		/* now wide spread use */
-	byte		wcache;		/* status of write cache */
-	byte		acoustic;	/* acoustic management */
-	unsigned int	failures;	/* current failure count */
-	unsigned int	max_failures;	/* maximum allowed failure count */
 	struct list_head list;
 	struct gendisk *disk;
 } ide_drive_t;
 
-/*
- * An ide_dmaproc_t() initiates/aborts DMA read/write operations on a drive.
- *
- * The caller is assumed to have selected the drive and programmed the drive's
- * sector address using CHS or LBA.  All that remains is to prepare for DMA
- * and then issue the actual read/write DMA/PIO command to the drive.
- *
- * Returns 0 if all went well.
- * Returns 1 if DMA read/write could not be started, in which case the caller
- * should either try again later, or revert to PIO for the current request.
- */
-typedef enum {	ide_dma_read,	ide_dma_write,		ide_dma_begin,
-		ide_dma_end,	ide_dma_check,		ide_dma_on,
-		ide_dma_off,	ide_dma_off_quietly,	ide_dma_test_irq,
-		ide_dma_host_on,			ide_dma_host_off,
-		ide_dma_bad_drive,			ide_dma_good_drive,
-		ide_dma_verbose,			ide_dma_retune,
-		ide_dma_lostirq,			ide_dma_timeout
-} ide_dma_action_t;
-
-typedef int (ide_dmaproc_t)(ide_dma_action_t, ide_drive_t *);
-
-/*
- * An ide_ideproc_t() performs CPU-polled transfers to/from a drive.
- * Arguments are: the drive, the buffer pointer, and the length (in bytes or
- * words depending on if it's an IDE or ATAPI call).
- *
- * If it is not defined for a controller, standard-code is used from ide.c.
- *
- * Controllers which are not memory-mapped in the standard way need to 
- * override that mechanism using this function to work.
- *
- */
-typedef enum { ideproc_ide_input_data,    ideproc_ide_output_data,
-	       ideproc_atapi_input_bytes, ideproc_atapi_output_bytes
-} ide_ide_action_t;
-
-typedef void (ide_ideproc_t)(ide_ide_action_t, ide_drive_t *, void *, unsigned int);
+typedef struct ide_pio_ops_s {
+	void (*ata_input_data)(ide_drive_t *, void *, u32);
+	void (*ata_output_data)(ide_drive_t *, void *, u32);
+
+	void (*atapi_input_bytes)(ide_drive_t *, void *, u32);
+	void (*atapi_output_bytes)(ide_drive_t *, void *, u32);
+} ide_pio_ops_t;
+
+typedef struct ide_dma_ops_s {
+	/* insert dma operations here! */
+	int (*ide_dma_read)(ide_drive_t *drive);
+	int (*ide_dma_write)(ide_drive_t *drive);
+	int (*ide_dma_begin)(ide_drive_t *drive);
+	int (*ide_dma_end)(ide_drive_t *drive);
+	int (*ide_dma_check)(ide_drive_t *drive);
+	int (*ide_dma_on)(ide_drive_t *drive);
+	int (*ide_dma_off)(ide_drive_t *drive);
+	int (*ide_dma_off_quietly)(ide_drive_t *drive);
+	int (*ide_dma_test_irq)(ide_drive_t *drive);
+	int (*ide_dma_host_on)(ide_drive_t *drive);
+	int (*ide_dma_host_off)(ide_drive_t *drive);
+	int (*ide_dma_bad_drive)(ide_drive_t *drive);
+	int (*ide_dma_good_drive)(ide_drive_t *drive);
+	int (*ide_dma_count)(ide_drive_t *drive);
+	int (*ide_dma_verbose)(ide_drive_t *drive);
+	int (*ide_dma_retune)(ide_drive_t *drive);
+	int (*ide_dma_lostirq)(ide_drive_t *drive);
+	int (*ide_dma_timeout)(ide_drive_t *drive);
+} ide_dma_ops_t;
 
 /*
  * mapping stuff, prepare for highmem...
@@ -602,166 +899,182 @@ extern inline void ide_unmap_buffer(char *buffer, unsigned long *flags)
 	bio_kunmap_irq(buffer, flags);
 }
 
-/*
- * A Verbose noise maker for debugging on the attempted transfer rates.
- */
-extern inline char *ide_xfer_verbose (byte xfer_rate)
-{
-	switch(xfer_rate) {
-		case XFER_UDMA_7:	return("UDMA 7");
-		case XFER_UDMA_6:	return("UDMA 6");
-		case XFER_UDMA_5:	return("UDMA 5");
-		case XFER_UDMA_4:	return("UDMA 4");
-		case XFER_UDMA_3:	return("UDMA 3");
-		case XFER_UDMA_2:	return("UDMA 2");
-		case XFER_UDMA_1:	return("UDMA 1");
-		case XFER_UDMA_0:	return("UDMA 0");
-		case XFER_MW_DMA_2:	return("MW DMA 2");
-		case XFER_MW_DMA_1:	return("MW DMA 1");
-		case XFER_MW_DMA_0:	return("MW DMA 0");
-		case XFER_SW_DMA_2:	return("SW DMA 2");
-		case XFER_SW_DMA_1:	return("SW DMA 1");
-		case XFER_SW_DMA_0:	return("SW DMA 0");
-		case XFER_PIO_4:	return("PIO 4");
-		case XFER_PIO_3:	return("PIO 3");
-		case XFER_PIO_2:	return("PIO 2");
-		case XFER_PIO_1:	return("PIO 1");
-		case XFER_PIO_0:	return("PIO 0");
-		case XFER_PIO_SLOW:	return("PIO SLOW");
-		default:		return("XFER ERROR");
-	}
-}
-
-/*
- * A Verbose noise maker for debugging on the attempted dmaing calls.
- */
-extern inline char *ide_dmafunc_verbose (ide_dma_action_t dmafunc)
-{
-	switch (dmafunc) {
-		case ide_dma_read:		return("ide_dma_read");
-		case ide_dma_write:		return("ide_dma_write");
-		case ide_dma_begin:		return("ide_dma_begin");
-		case ide_dma_end:		return("ide_dma_end:");
-		case ide_dma_check:		return("ide_dma_check");
-		case ide_dma_on:		return("ide_dma_on");
-		case ide_dma_off:		return("ide_dma_off");
-		case ide_dma_off_quietly:	return("ide_dma_off_quietly");
-		case ide_dma_test_irq:		return("ide_dma_test_irq");
-		case ide_dma_host_on:		return("ide_dma_host_on");
-		case ide_dma_host_off:		return("ide_dma_host_off");
-		case ide_dma_bad_drive:		return("ide_dma_bad_drive");
-		case ide_dma_good_drive:	return("ide_dma_good_drive");
-		case ide_dma_verbose:		return("ide_dma_verbose");
-		case ide_dma_retune:		return("ide_dma_retune");
-		case ide_dma_lostirq:		return("ide_dma_lostirq");
-		case ide_dma_timeout:		return("ide_dma_timeout");
-		default:			return("unknown");
-	}
-}
-
-/*
- * An ide_tuneproc_t() is used to set the speed of an IDE interface
- * to a particular PIO mode.  The "byte" parameter is used
- * to select the PIO mode by number (0,1,2,3,4,5), and a value of 255
- * indicates that the interface driver should "auto-tune" the PIO mode
- * according to the drive capabilities in drive->id;
- *
- * Not all interface types support tuning, and not all of those
- * support all possible PIO settings.  They may silently ignore
- * or round values as they see fit.
- */
-typedef void (ide_tuneproc_t) (ide_drive_t *, byte);
-typedef int (ide_speedproc_t) (ide_drive_t *, byte);
-
-/*
- * This is used to provide support for strange interfaces
- */
-typedef void (ide_selectproc_t) (ide_drive_t *);
-typedef void (ide_resetproc_t) (ide_drive_t *);
-typedef int (ide_quirkproc_t) (ide_drive_t *);
-typedef void (ide_intrproc_t) (ide_drive_t *);
-typedef void (ide_maskproc_t) (ide_drive_t *, int);
-typedef void (ide_rw_proc_t) (ide_drive_t *, ide_dma_action_t);
-
-/*
- * ide soft-power support
- */
-typedef int (ide_busproc_t) (ide_drive_t *, int);
-
 #define IDE_CHIPSET_PCI_MASK	\
     ((1<<ide_pci)|(1<<ide_cmd646)|(1<<ide_ali14xx))
 #define IDE_CHIPSET_IS_PCI(c)	((IDE_CHIPSET_PCI_MASK >> (c)) & 1)
 
 #ifdef CONFIG_BLK_DEV_IDEPCI
-typedef struct ide_pci_devid_s {
-	unsigned short	vid;
-	unsigned short	did;
-} ide_pci_devid_t;
-
-#define IDE_PCI_DEVID_NULL	((ide_pci_devid_t){0,0})
-#define IDE_PCI_DEVID_EQ(a,b)	(a.vid == b.vid && a.did == b.did)
+struct ide_pci_device_s;
 #endif /* CONFIG_BLK_DEV_IDEPCI */
 
 typedef struct hwif_s {
-	struct hwif_s	*next;		/* for linked-list in ide_hwgroup_t */
+	struct hwif_s *next;		/* for linked-list in ide_hwgroup_t */
+	struct hwif_s *mate;		/* other hwif from same PCI chip */
 	struct hwgroup_s *hwgroup;	/* actually (ide_hwgroup_t *) */
-	ide_ioreg_t	io_ports[IDE_NR_PORTS];	/* task file registers */
-/*
- *     FIXME!! need a generic register set :-/  PPC guys ideas??
- *
- *     ide_mmioreg_t   mm_ports[IDE_NR_PORTS]; "task file registers"
- *
- */
+	struct proc_dir_entry *proc;	/* /proc/ide/ directory entry */
+
+	char name[6];			/* name of interface, eg. "ide0" */
+
+		/* task file registers for pata and sata */
+	ide_ioreg_t	io_ports[IDE_NR_PORTS];
+	sata_ioreg_t	sata_scr[SATA_NR_PORTS];
+	sata_ioreg_t	sata_misc[SATA_NR_PORTS];
+
 	hw_regs_t	hw;		/* Hardware info */
 	ide_drive_t	drives[MAX_DRIVES];	/* drive info */
-	int		addressing;	/* hosts addressing */
-	void		(*tuneproc)(ide_drive_t *, byte);	/* routine to tune PIO mode for drives */
-	int		(*speedproc)(ide_drive_t *, byte);	/* routine to retune DMA modes for drives */
-	void		(*selectproc)(ide_drive_t *);		/* tweaks hardware to select drive */
-	void		(*resetproc)(ide_drive_t *);		/* routine to reset controller after a disk reset */
-	void		(*intrproc)(ide_drive_t *);		/* special interrupt handling for shared pci interrupts */
-	void		(*maskproc)(ide_drive_t *, int);	/* special host masking for drive selection */
-	int		(*quirkproc)(ide_drive_t *);		/* check host's drive quirk list */
-	void		(*rwproc)(ide_drive_t *, ide_dma_action_t);	/* adjust timing based upon rq->cmd direction */
-	void		(*ideproc)(ide_ide_action_t, ide_drive_t *, void *, unsigned int);	/* CPU-polled transfer routine */
-	int		(*dmaproc)(ide_dma_action_t, ide_drive_t *);	/* dma read/write/abort routine */
-	int		(*busproc)(ide_drive_t *, int);		/* driver soft-power interface */
-	unsigned int	*dmatable_cpu;	/* dma physical region descriptor table (cpu view) */
-	dma_addr_t	dmatable_dma;	/* dma physical region descriptor table (dma view) */
-	struct scatterlist *sg_table;	/* Scatter-gather list used to build the above */
+
+	u8 major;	/* our major number */
+	u8 index;	/* 0 for ide0; 1 for ide1; ... */
+	u8 channel;	/* for dual-port chips: 0=primary, 1=secondary */
+	u8 straight8;	/* Alan's straight 8 check */
+	u8 bus_state;	/* power state of the IDE bus */
+
+	u8 atapi_dma;	/* host supports atapi_dma */
+	u8 ultra_mask;
+	u8 mwdma_mask;
+	u8 swdma_mask;
+
+	hwif_chipset_t chipset;	/* sub-module for tuning.. */
+
+#ifdef CONFIG_BLK_DEV_IDEPCI
+	struct pci_dev  *pci_dev;	/* for pci chipsets */
+	struct ide_pci_device_s	*cds;	/* chipset device struct */
+#endif /* CONFIG_BLK_DEV_IDEPCI */
+
+#if 0
+	ide_hwif_ops_t	*hwifops;
+#else
+	/* routine is for HBA specific IDENTITY operations */
+	int	(*identify)(ide_drive_t *);
+	/* routine to tune PIO mode for drives */
+	void	(*tuneproc)(ide_drive_t *, u8);
+	/* routine to retune DMA modes for drives */
+	int	(*speedproc)(ide_drive_t *, u8);
+	/* tweaks hardware to select drive */
+	void	(*selectproc)(ide_drive_t *);
+	/* chipset polling based on hba specifics */
+	int	(*reset_poll)(ide_drive_t *);
+	/* chipset specific changes to default for device-hba resets */
+	void	(*pre_reset)(ide_drive_t *);
+	/* routine to reset controller after a disk reset */
+	void	(*resetproc)(ide_drive_t *);
+	/* special interrupt handling for shared pci interrupts */
+	void	(*intrproc)(ide_drive_t *);
+	/* special host masking for drive selection */
+	void	(*maskproc)(ide_drive_t *, int);
+	/* check host's drive quirk list */
+	int	(*quirkproc)(ide_drive_t *);
+	/* driver soft-power interface */
+	int	(*busproc)(ide_drive_t *, int);
+//	/* host rate limiter */
+//	u8	(*ratemask)(ide_drive_t *);
+//	/* device rate limiter */
+//	u8	(*ratefilter)(ide_drive_t *, u8);
+#endif
+
+#if 0
+	ide_pio_ops_t	*pioops;
+#else
+	void (*ata_input_data)(ide_drive_t *, void *, u32);
+	void (*ata_output_data)(ide_drive_t *, void *, u32);
+
+	void (*atapi_input_bytes)(ide_drive_t *, void *, u32);
+	void (*atapi_output_bytes)(ide_drive_t *, void *, u32);
+#endif
+
+#if 0
+	ide_dma_ops_t	*dmaops;
+#else
+	int (*ide_dma_read)(ide_drive_t *drive);
+	int (*ide_dma_write)(ide_drive_t *drive);
+	int (*ide_dma_begin)(ide_drive_t *drive);
+	int (*ide_dma_end)(ide_drive_t *drive);
+	int (*ide_dma_check)(ide_drive_t *drive);
+	int (*ide_dma_on)(ide_drive_t *drive);
+	int (*ide_dma_off)(ide_drive_t *drive);
+	int (*ide_dma_off_quietly)(ide_drive_t *drive);
+	int (*ide_dma_test_irq)(ide_drive_t *drive);
+	int (*ide_dma_host_on)(ide_drive_t *drive);
+	int (*ide_dma_host_off)(ide_drive_t *drive);
+	int (*ide_dma_bad_drive)(ide_drive_t *drive);
+	int (*ide_dma_good_drive)(ide_drive_t *drive);
+	int (*ide_dma_count)(ide_drive_t *drive);
+	int (*ide_dma_verbose)(ide_drive_t *drive);
+	int (*ide_dma_retune)(ide_drive_t *drive);
+	int (*ide_dma_lostirq)(ide_drive_t *drive);
+	int (*ide_dma_timeout)(ide_drive_t *drive);
+#endif
+
+#if 0
+	ide_io_ops_t	*iops;
+#else
+	void (*OUTB)(u8 addr, u32 port);
+	void (*OUTW)(u16 addr, u32 port);
+	void (*OUTL)(u32 addr, u32 port);
+	void (*OUTBP)(u8 addr, u32 port);
+	void (*OUTWP)(u16 addr, u32 port);
+	void (*OUTLP)(u32 addr, u32 port);
+	void (*OUTSW)(u32 port, void *addr, u32 count);
+	void (*OUTSWP)(u32 port, void *addr, u32 count);
+	void (*OUTSL)(u32 port, void *addr, u32 count);
+	void (*OUTSLP)(u32 port, void *addr, u32 count);
+
+	u8  (*INB)(u32 port);
+	u16 (*INW)(u32 port);
+	u32 (*INL)(u32 port);
+	u8  (*INBP)(u32 port);
+	u16 (*INWP)(u32 port);
+	u32 (*INLP)(u32 port);
+	void (*INSW)(u32 port, void *addr, u32 count);
+	void (*INSWP)(u32 port, void *addr, u32 count);
+	void (*INSL)(u32 port, void *addr, u32 count);
+	void (*INSLP)(u32 port, void *addr, u32 count);
+#endif
+
+	/* dma physical region descriptor table (cpu view) */
+	unsigned int	*dmatable_cpu;
+	/* dma physical region descriptor table (dma view) */
+	dma_addr_t	dmatable_dma;
+	/* Scatter-gather list used to build the above */
+	struct scatterlist *sg_table;
 	int sg_nents;			/* Current number of entries in it */
 	int sg_dma_direction;		/* dma transfer direction */
 	int sg_dma_active;		/* is it in use */
-	struct hwif_s	*mate;		/* other hwif from same PCI chip */
+
+	int		mmio;		/* hosts iomio (0), mmio (1) or custom (2) select */
+	int		rqsize;		/* max sectors per request */
+	int		addressing;	/* hosts addressing */
+	int		irq;		/* our irq number */
+	int		initializing;	/* set while initializing self */
+
+	unsigned long	dma_master;	/* reference base addr dmabase */
 	unsigned long	dma_base;	/* base addr for dma ports */
+	unsigned long	dma_command;	/* dma command register */
+	unsigned long	dma_vendor1;	/* dma vendor 1 register */
+	unsigned long	dma_status;	/* dma status register */
+	unsigned long	dma_vendor3;	/* dma vendor 3 register */
+	unsigned long	dma_prdtable;	/* actual prd table address */
+	unsigned long	dma_base2;	/* extended base addr for dma ports */
+
 	unsigned	dma_extra;	/* extra addr for dma ports */
 	unsigned long	config_data;	/* for use by chipset-specific code */
 	unsigned long	select_data;	/* for use by chipset-specific code */
-	struct proc_dir_entry *proc;	/* /proc/ide/ directory entry */
-	int		irq;		/* our irq number */
-	byte		major;		/* our major number */
-	char 		name[6];	/* name of interface, eg. "ide0" */
-	byte		index;		/* 0 for ide0; 1 for ide1; ... */
-	hwif_chipset_t	chipset;	/* sub-module for tuning.. */
+#if (DISK_RECOVERY_TIME > 0)
+	unsigned long	last_time;	/* time when previous rq was done */
+#endif
+
+
 	unsigned	noprobe    : 1;	/* don't probe for this interface */
 	unsigned	present    : 1;	/* this interface exists */
-	unsigned	serialized : 1;	/* serialized operation with mate hwif */
+	unsigned	serialized : 1;	/* serialized all channel operation */
 	unsigned	sharing_irq: 1;	/* 1 = sharing irq with another hwif */
 	unsigned	reset      : 1;	/* reset after probe */
-	unsigned	autodma    : 1;	/* automatically try to enable DMA at boot */
+	unsigned	autodma    : 1;	/* auto-attempt using DMA at boot */
 	unsigned	udma_four  : 1;	/* 1=ATA-66 capable, 0=default */
-	unsigned	no_highmem : 1;	/* always use high i/o bounce */
-	byte		channel;	/* for dual-port chips: 0=primary, 1=secondary */
-#ifdef CONFIG_BLK_DEV_IDEPCI
-	struct pci_dev	*pci_dev;	/* for pci chipsets */
-	ide_pci_devid_t	pci_devid;	/* for pci chipsets: {VID,DID} */
-#endif /* CONFIG_BLK_DEV_IDEPCI */
-#if (DISK_RECOVERY_TIME > 0)
-	unsigned long	last_time;	/* time when previous rq was done */
-#endif
-	byte		straight8;	/* Alan's straight 8 check */
+	unsigned	highmem    : 1;	/* can do full 32-bit dma */
+	unsigned	no_dsc     : 1;	/* 0 default, 1 dsc_overlap disabled */
+
 	void		*hwif_data;	/* extra hwif data */
-	byte		bus_state;	/* power state of the IDE bus */
 } ide_hwif_t;
 
 /*
@@ -769,7 +1082,7 @@ typedef struct hwif_s {
  */
 typedef enum {
 	ide_stopped,	/* no drive operation was started */
-	ide_started	/* a drive operation was started, and a handler was set */
+	ide_started	/* a drive operation was started, handler was set */
 } ide_startstop_t;
 
 /*
@@ -778,26 +1091,41 @@ typedef enum {
 typedef ide_startstop_t (ide_pre_handler_t)(ide_drive_t *, struct request *);
 typedef ide_startstop_t (ide_handler_t)(ide_drive_t *);
 typedef ide_startstop_t (ide_post_handler_t)(ide_drive_t *);
-
-/*
- * when ide_timer_expiry fires, invoke a handler of this type
- * to decide what to do.
- */
 typedef int (ide_expiry_t)(ide_drive_t *);
 
 typedef struct hwgroup_s {
-	ide_handler_t		*handler;/* irq handler, if active */
-	ide_handler_t		*handler_save;/* irq handler, if active */
-	volatile int		busy;	/* BOOL: protects all fields below */
-	int			sleeping; /* BOOL: wake us up on timer expiry */
-	ide_drive_t		*drive;	/* current drive */
-	ide_hwif_t		*hwif;	/* ptr to current hwif in linked-list */
-	struct request		*rq;	/* current request */
-	struct timer_list	timer;	/* failsafe timer */
-	struct request		wrq;	/* local copy of current write rq */
-	unsigned long		poll_timeout;	/* timeout value during long polls */
-	ide_expiry_t		*expiry;	/* queried upon timeouts */
-	int			pio_clock;	/* ide_system_bus_speed */
+		/* irq handler, if active */
+	ide_startstop_t	(*handler)(ide_drive_t *);
+		/* irq handler, suspended if active */
+	ide_startstop_t	(*handler_save)(ide_drive_t *);
+		/* BOOL: protects all fields below */
+	volatile int busy;
+		/* BOOL: wake us up on timer expiry */
+	int sleeping;
+		/* current drive */
+	ide_drive_t *drive;
+		/* ptr to current hwif in linked-list */
+	ide_hwif_t *hwif;
+
+#ifdef CONFIG_BLK_DEV_IDEPCI
+		/* for pci chipsets */
+	struct pci_dev *pci_dev;
+		/* chipset device struct */
+	struct ide_pci_device_s *cds;
+#endif /* CONFIG_BLK_DEV_IDEPCI */
+
+		/* current request */
+	struct request *rq;
+		/* failsafe timer */
+	struct timer_list timer;
+		/* local copy of current write rq */
+	struct request wrq;
+		/* timeout value during long polls */
+	unsigned long poll_timeout;
+		/* queried upon timeouts */
+	int (*expiry)(ide_drive_t *);
+		/* ide_system_bus_speed */
+	int pio_clock;
 } ide_hwgroup_t;
 
 /* structure attached to the request for IDE_TASK_CMDS */
@@ -850,14 +1178,14 @@ typedef struct {
 } ide_proc_entry_t;
 
 #ifdef CONFIG_PROC_FS
-void proc_ide_create(void);
-void proc_ide_destroy(void);
-void recreate_proc_ide_device(ide_hwif_t *, ide_drive_t *);
-void destroy_proc_ide_device(ide_hwif_t *, ide_drive_t *);
-void destroy_proc_ide_drives(ide_hwif_t *);
-void create_proc_ide_interfaces(void);
-void ide_add_proc_entries(struct proc_dir_entry *dir, ide_proc_entry_t *p, void *data);
-void ide_remove_proc_entries(struct proc_dir_entry *dir, ide_proc_entry_t *p);
+extern void proc_ide_create(void);
+extern void proc_ide_destroy(void);
+extern void recreate_proc_ide_device(ide_hwif_t *, ide_drive_t *);
+extern void destroy_proc_ide_device(ide_hwif_t *, ide_drive_t *);
+extern void destroy_proc_ide_drives(ide_hwif_t *);
+extern void create_proc_ide_interfaces(void);
+extern void ide_add_proc_entries(struct proc_dir_entry *, ide_proc_entry_t *, void *);
+extern void ide_remove_proc_entries(struct proc_dir_entry *, ide_proc_entry_t *);
 read_proc_t proc_ide_read_capacity;
 read_proc_t proc_ide_read_geometry;
 
@@ -889,7 +1217,7 @@ typedef struct ide_driver_s {
 	struct module			*owner;
 	const char			*name;
 	const char			*version;
-	byte				media;
+	u8				media;
 	unsigned busy			: 1;
 	unsigned supports_dma		: 1;
 	unsigned supports_dsc_overlap	: 1;
@@ -899,9 +1227,9 @@ typedef struct ide_driver_s {
 	int		(*resume)(ide_drive_t *);
 	int		(*flushcache)(ide_drive_t *);
 	ide_startstop_t	(*do_request)(ide_drive_t *, struct request *, unsigned long);
-	int		(*end_request)(ide_drive_t *, int);
-	byte		(*sense)(ide_drive_t *, const char *, byte);
-	ide_startstop_t (*error)(ide_drive_t *, const char *, byte);
+	int		(*end_request)(ide_drive_t *, int, int);
+	u8		(*sense)(ide_drive_t *, const char *, u8);
+	ide_startstop_t	(*error)(ide_drive_t *, const char *, u8);
 	int		(*ioctl)(ide_drive_t *, struct inode *, struct file *, unsigned int, unsigned long);
 	int		(*open)(struct inode *, struct file *, ide_drive_t *);
 	void		(*release)(struct inode *, struct file *, ide_drive_t *);
@@ -910,8 +1238,8 @@ typedef struct ide_driver_s {
 	void		(*pre_reset)(ide_drive_t *);
 	unsigned long	(*capacity)(ide_drive_t *);
 	ide_startstop_t	(*special)(ide_drive_t *);
-	ide_proc_entry_t        *proc;
-	int		(*reinit)(ide_drive_t *);
+	ide_proc_entry_t	*proc;
+	int		(*attach)(ide_drive_t *);
 	void		(*ata_prebuilder)(ide_drive_t *);
 	void		(*atapi_prebuilder)(ide_drive_t *);
 	struct list_head drives;
@@ -935,6 +1263,13 @@ typedef struct ide_module_s {
 	struct ide_module_s		*next;
 } ide_module_t;
 
+typedef struct ide_devices_s {
+	char			name[4];		/* hdX */
+	unsigned		attached	: 1;	/* native */
+	unsigned		alttached	: 1;	/* alternate */
+	struct ide_devices_s	*next;
+} ide_devices_t;
+
 /*
  * ide_hwifs[] is the master data structure used to keep track
  * of just about everything in ide.c.  Whenever possible, routines
@@ -945,7 +1280,15 @@ typedef struct ide_module_s {
  */
 #ifndef _IDE_C
 extern	ide_hwif_t	ide_hwifs[];		/* master data repository */
+extern ide_module_t	*ide_chipsets;
 extern	ide_module_t	*ide_probe;
+
+extern ide_devices_t   *idedisk;
+extern ide_devices_t   *idecd;
+extern ide_devices_t   *idefloppy;
+extern ide_devices_t   *idetape;
+extern ide_devices_t   *idescsi;
+
 #endif
 extern int noautodma;
 
@@ -957,38 +1300,47 @@ extern int noautodma;
 #define DEVICE_NR(device)	(minor(device) >> PARTN_BITS)
 #include <linux/blk.h>
 
-int ide_end_request (ide_drive_t *drive, int uptodate);
+extern int ide_end_request (ide_drive_t *drive, int uptodate, int nrsecs);
 
 /*
  * This is used on exit from the driver, to designate the next irq handler
  * and also to start the safety timer.
  */
-void ide_set_handler (ide_drive_t *drive, ide_handler_t *handler, unsigned int timeout, ide_expiry_t *expiry);
+extern void ide_set_handler (ide_drive_t *drive, ide_handler_t *handler, unsigned int timeout, ide_expiry_t *expiry);
 
 /*
  * Error reporting, in human readable form (luxurious, but a memory hog).
+ *
+ * (drive, msg, status)
  */
 byte ide_dump_status (ide_drive_t *drive, const char *msg, byte stat);
 
 /*
  * ide_error() takes action based on the error returned by the controller.
  * The caller should return immediately after invoking this.
+ *
+ * (drive, msg, status)
  */
 ide_startstop_t ide_error (ide_drive_t *drive, const char *msg, byte stat);
 
 /*
  * Issue a simple drive command
  * The drive must be selected beforehand.
+ *
+ * (drive, command, nsector, handler)
  */
-void ide_cmd (ide_drive_t *drive, byte cmd, byte nsect, ide_handler_t *handler);
+extern void ide_cmd(ide_drive_t *, u8, u8, ide_handler_t *);
 
+extern void ide_fix_driveid(struct hd_driveid *);
 /*
  * ide_fixstring() cleans up and (optionally) byte-swaps a text string,
  * removing leading/trailing blanks and compressing internal blanks.
  * It is primarily used to tidy up the model name/number fields as
  * returned by the WIN_[P]IDENTIFY commands.
+ *
+ * (s, bytecount, byteswap)
  */
-void ide_fixstring (byte *s, const int bytecount, const int byteswap);
+extern void ide_fixstring(u8 *, const int, const int);
 
 /*
  * This routine busy-waits for the drive status to be not "busy".
@@ -997,43 +1349,44 @@ void ide_fixstring (byte *s, const int bytecount, const int byteswap);
  * cases return 1 after doing "*startstop = ide_error()", and the
  * caller should return the updated value of "startstop" in this case.
  * "startstop" is unchanged when the function returns 0;
+ * (startstop, drive, good, bad, timeout)
  */
-int ide_wait_stat (ide_startstop_t *startstop, ide_drive_t *drive, byte good, byte bad, unsigned long timeout);
+extern int ide_wait_stat(ide_startstop_t *, ide_drive_t *, u8, u8, unsigned long);
 
 /*
  * This routine is called from the partition-table code in genhd.c
  * to "convert" a drive to a logical geometry with fewer than 1024 cyls.
  */
-int ide_xlate_1024 (kdev_t, int, int, const char *);
+extern int ide_xlate_1024 (kdev_t, int, int, const char *);
 
 /*
  * Convert kdev_t structure into ide_drive_t * one.
  */
-ide_drive_t *get_info_ptr (kdev_t i_rdev);
+extern ide_drive_t *get_info_ptr (kdev_t i_rdev);
 
 /*
  * Return the current idea about the total capacity of this drive.
  */
-unsigned long current_capacity (ide_drive_t *drive);
+extern unsigned long current_capacity (ide_drive_t *drive);
 
-void ide_revalidate_drive (ide_drive_t *drive);
+extern void ide_revalidate_drive (ide_drive_t *drive);
 
 /*
  * Start a reset operation for an IDE interface.
  * The caller should return immediately after invoking this.
  */
-ide_startstop_t ide_do_reset (ide_drive_t *);
+extern ide_startstop_t ide_do_reset (ide_drive_t *);
 
 /*
  * Re-Start an operation for an IDE interface.
  * The caller should return immediately after invoking this.
  */
-int restart_request (ide_drive_t *, struct request *);
+extern int restart_request (ide_drive_t *, struct request *);
 
 /*
  * This function is intended to be used prior to invoking ide_do_drive_cmd().
  */
-void ide_init_drive_cmd (struct request *rq);
+extern void ide_init_drive_cmd (struct request *rq);
 
 /*
  * "action" parameter type for ide_do_drive_cmd() below.
@@ -1070,23 +1423,35 @@ typedef enum {
  * for the new rq to be completed. This is again intended for careful
  * use by the ATAPI tape/cdrom driver code.
  */
-int ide_do_drive_cmd (ide_drive_t *drive, struct request *rq, ide_action_t action);
+extern int ide_do_drive_cmd(ide_drive_t *, struct request *, ide_action_t);
 
 /*
  * Clean up after success/failure of an explicit drive cmd.
  * stat/err are used only when (HWGROUP(drive)->rq->cmd == IDE_DRIVE_CMD).
  * stat/err are used only when (HWGROUP(drive)->rq->cmd == IDE_DRIVE_TASK_MASK).
+ *
+ * (ide_drive_t *drive, u8 stat, u8 err)
  */
-void ide_end_drive_cmd (ide_drive_t *drive, byte stat, byte err);
+extern void ide_end_drive_cmd(ide_drive_t *, u8, u8);
 
 /*
- * Issue ATA command and wait for completion. use for implementing commands in kernel
+ * Issue ATA command and wait for completion.
+ * Use for implementing commands in kernel
+ *
+ *  (ide_drive_t *drive, u8 cmd, u8 nsect, u8 feature, u8 sectors, u8 *buf)
  */
-int ide_wait_cmd (ide_drive_t *drive, int cmd, int nsect, int feature, int sectors, byte *buf);
+extern int ide_wait_cmd(ide_drive_t *, u8, u8, u8, u8, u8 *);
+
+/* (ide_drive_t *drive, u8 *buf) */
+extern int ide_wait_cmd_task(ide_drive_t *, u8 *);
 
-int ide_wait_cmd_task (ide_drive_t *drive, byte *buf);
- 
 typedef struct ide_task_s {
+/*
+ *	struct hd_drive_task_hdr	tf;
+ *	task_struct_t		tf;
+ *	struct hd_drive_hob_hdr		hobf;
+ *	hob_struct_t		hobf;
+ */
 	task_ioreg_t		tfRegister[8];
 	task_ioreg_t		hobRegister[8];
 	ide_reg_valid_t		tf_out_flags;
@@ -1101,6 +1466,11 @@ typedef struct ide_task_s {
 } ide_task_t;
 
 typedef struct pkt_task_s {
+/*
+ *	struct hd_drive_task_hdr	pktf;
+ *	task_struct_t		pktf;
+ *	u8			pkcdb[12];
+ */
 	task_ioreg_t		tfRegister[8];
 	int			data_phase;
 	int			command_type;
@@ -1109,66 +1479,129 @@ typedef struct pkt_task_s {
 	void			*special;
 } pkt_task_t;
 
-void ata_input_data (ide_drive_t *drive, void *buffer, unsigned int wcount);
-void ata_output_data (ide_drive_t *drive, void *buffer, unsigned int wcount);
-void atapi_input_bytes (ide_drive_t *drive, void *buffer, unsigned int bytecount);
-void atapi_output_bytes (ide_drive_t *drive, void *buffer, unsigned int bytecount);
-void taskfile_input_data (ide_drive_t *drive, void *buffer, unsigned int wcount);
-void taskfile_output_data (ide_drive_t *drive, void *buffer, unsigned int wcount);
+extern inline void SELECT_DRIVE(ide_drive_t *);
+extern inline void SELECT_INTERRUPT(ide_drive_t *);
+extern inline void SELECT_MASK(ide_drive_t *, int);
+extern inline void QUIRK_LIST(ide_drive_t *);
 
-int drive_is_ready (ide_drive_t *drive);
-int wait_for_ready (ide_drive_t *drive, int timeout);
+extern void ata_input_data(ide_drive_t *, void *, u32);
+extern void ata_output_data(ide_drive_t *, void *, u32);
+extern void atapi_input_bytes(ide_drive_t *, void *, u32);
+extern void atapi_output_bytes(ide_drive_t *, void *, u32);
+extern void taskfile_input_data(ide_drive_t *, void *, u32);
+extern void taskfile_output_data(ide_drive_t *, void *, u32);
+
+extern int drive_is_ready(ide_drive_t *);
+extern int wait_for_ready(ide_drive_t *, int /* timeout */);
 
 /*
  * taskfile io for disks for now...and builds request from ide_ioctl
  */
-ide_startstop_t do_rw_taskfile (ide_drive_t *drive, ide_task_t *task);
+extern ide_startstop_t do_rw_taskfile(ide_drive_t *, ide_task_t *);
 
-void ide_end_taskfile (ide_drive_t *drive, byte stat, byte err);
+/* (ide_drive_t *drive, u8 stat, u8 err) */
+extern void ide_end_taskfile(ide_drive_t *, u8, u8);
 
 /*
  * Special Flagged Register Validation Caller
  */
-ide_startstop_t flagged_taskfile (ide_drive_t *drive, ide_task_t *task);
-
-ide_startstop_t set_multmode_intr (ide_drive_t *drive);
-ide_startstop_t set_geometry_intr (ide_drive_t *drive);
-ide_startstop_t recal_intr (ide_drive_t *drive);
-ide_startstop_t task_no_data_intr (ide_drive_t *drive);
-ide_startstop_t task_in_intr (ide_drive_t *drive);
-ide_startstop_t task_mulin_intr (ide_drive_t *drive);
-ide_startstop_t pre_task_out_intr (ide_drive_t *drive, struct request *rq);
-ide_startstop_t task_out_intr (ide_drive_t *drive);
-ide_startstop_t pre_task_mulout_intr (ide_drive_t *drive, struct request *rq);
-ide_startstop_t task_mulout_intr (ide_drive_t *drive);
-void ide_init_drive_taskfile (struct request *rq);
-
-int ide_raw_taskfile (ide_drive_t *drive, ide_task_t *cmd, byte *buf);
-
-ide_pre_handler_t * ide_pre_handler_parser (struct hd_drive_task_hdr *taskfile, struct hd_drive_hob_hdr *hobfile);
-ide_handler_t * ide_handler_parser (struct hd_drive_task_hdr *taskfile, struct hd_drive_hob_hdr *hobfile);
-ide_post_handler_t * ide_post_handler_parser (struct hd_drive_task_hdr *taskfile, struct hd_drive_hob_hdr *hobfile);
+extern ide_startstop_t flagged_taskfile(ide_drive_t *, ide_task_t *);
+
+extern ide_startstop_t set_multmode_intr(ide_drive_t *);
+extern ide_startstop_t set_geometry_intr(ide_drive_t *);
+extern ide_startstop_t recal_intr(ide_drive_t *);
+extern ide_startstop_t task_no_data_intr(ide_drive_t *);
+extern ide_startstop_t task_in_intr(ide_drive_t *);
+extern ide_startstop_t task_mulin_intr(ide_drive_t *);
+extern ide_startstop_t pre_task_out_intr(ide_drive_t *, struct request *);
+extern ide_startstop_t task_out_intr(ide_drive_t *);
+extern ide_startstop_t pre_task_mulout_intr(ide_drive_t *, struct request *);
+extern ide_startstop_t task_mulout_intr(ide_drive_t *);
+extern void ide_init_drive_taskfile(struct request *);
+
+extern int ide_raw_taskfile(ide_drive_t *, ide_task_t *, u8 *);
+
+extern ide_pre_handler_t * ide_pre_handler_parser(struct hd_drive_task_hdr *, struct hd_drive_hob_hdr *);
+
+extern ide_handler_t * ide_handler_parser(struct hd_drive_task_hdr *, struct hd_drive_hob_hdr *);
+
+extern ide_post_handler_t * ide_post_handler_parser(struct hd_drive_task_hdr *, struct hd_drive_hob_hdr *);
+
 /* Expects args is a full set of TF registers and parses the command type */
-int ide_cmd_type_parser (ide_task_t *args);
+extern int ide_cmd_type_parser(ide_task_t *);
+
+int ide_taskfile_ioctl(ide_drive_t *, struct inode *, struct file *, unsigned int, unsigned long);
+int ide_cmd_ioctl(ide_drive_t *, struct inode *, struct file *, unsigned int, unsigned long);
+int ide_task_ioctl(ide_drive_t *, struct inode *, struct file *, unsigned int, unsigned long);
+
+#if 0
+
+#define IDEFLOPPY_PC_BUFFER_SIZE        256
+#define IDETAPE_PC_BUFFER_SIZE          256
+#define IDE_PC_BUFFER_SIZE          256
+
+typedef struct ide_packet_command_s {
+		/* Actual packet bytes */
+	u8 c[12];
+		/* On each retry, we increment retries */
+	int retries;
+		/* Error code */
+	int error;
+		/* Bytes to transfer */
+	int request_transfer;
+		/* Bytes actually transferred */
+	int actually_transferred;
+		/* Size of our data buffer */
+	int buffer_size;
+
+	struct buffer_head *bh;
+	u8 *b_data;
+		/* The corresponding request */
+	struct request *rq;
+# if 0
+		/* Scatter gather table */
+	struct scatterlist *sg;
+# endif
+	int b_count;
+		/* Data buffer */
+	u8 *buffer;
+		/* Pointer into the above buffer */
+	u8 *current_position;
+		/* Called when this packet command is completed */
+	ide_startstop_t (*callback) (ide_drive_t *);
+		/* Temporary buffer */
+	u8 pc_buffer[IDE_PC_BUFFER_SIZE];
+		/* Status/Action bit flags: long for set_bit */
+	unsigned long flags;
+} ide_pc_t;
+
+ide-cd orthoginal :-/
+struct packet_command {
+        char *buffer;
+        int buflen;
+        int stat;
+        int quiet;
+        int timeout;
+        struct request_sense *sense;
+        unsigned char c[12];
+};
 
-int ide_taskfile_ioctl (ide_drive_t *drive, struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg);
-int ide_cmd_ioctl (ide_drive_t *drive, struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg);
-int ide_task_ioctl (ide_drive_t *drive, struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg);
+#endif
 
 #ifdef CONFIG_PKT_TASK_IOCTL
-int pkt_taskfile_ioctl (ide_drive_t *drive, struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg);
+extern int pkt_taskfile_ioctl(ide_drive_t *, struct inode *, struct file *, unsigned int, unsigned long);
 #endif /* CONFIG_PKT_TASK_IOCTL */
 
-void ide_delay_50ms (void);
-int system_bus_clock(void);
+extern void ide_delay_50ms(void);
+extern int system_bus_clock(void);
 
-byte ide_auto_reduce_xfer (ide_drive_t *drive);
-int ide_driveid_update (ide_drive_t *drive);
-int ide_ata66_check (ide_drive_t *drive, ide_task_t *args);
-int ide_config_drive_speed (ide_drive_t *drive, byte speed);
-byte eighty_ninty_three (ide_drive_t *drive);
-int set_transfer (ide_drive_t *drive, ide_task_t *args);
-int taskfile_lib_get_identify (ide_drive_t *drive, byte *buf);
+extern u8 ide_auto_reduce_xfer(ide_drive_t *);
+extern int ide_driveid_update(ide_drive_t *);
+extern int ide_ata66_check(ide_drive_t *, ide_task_t *);
+extern int ide_config_drive_speed(ide_drive_t *, u8);
+extern u8 eighty_ninty_three (ide_drive_t *);
+extern int set_transfer(ide_drive_t *, ide_task_t *);
+extern int taskfile_lib_get_identify(ide_drive_t *drive, u8 *);
 
 /*
  * ide_system_bus_speed() returns what we think is the system VESA/PCI
@@ -1176,45 +1609,55 @@ int taskfile_lib_get_identify (ide_drive_t *drive, byte *buf);
  * The default is 40 for known PCI systems, 50 otherwise.
  * The "idebus=xx" parameter can be used to override this value.
  */
-int ide_system_bus_speed (void);
+extern int ide_system_bus_speed(void);
 
 /*
  * ide_stall_queue() can be used by a drive to give excess bandwidth back
  * to the hwgroup by sleeping for timeout jiffies.
  */
-void ide_stall_queue (ide_drive_t *drive, unsigned long timeout);
+extern void ide_stall_queue(ide_drive_t *drive, unsigned long timeout);
 
 /*
  * ide_get_queue() returns the queue which corresponds to a given device.
  */
-request_queue_t *ide_get_queue (kdev_t dev);
+extern request_queue_t *ide_get_queue (kdev_t dev);
 
 /*
  * CompactFlash cards and their brethern pretend to be removable hard disks,
  * but they never have a slave unit, and they don't have doorlock mechanisms.
- * This test catches them, and is invoked elsewhere when setting appropriate config bits.
+ * This test catches them, and is invoked elsewhere when setting appropriate
+ * config bits.
  */
-int drive_is_flashcard (ide_drive_t *drive);
+extern int drive_is_flashcard (ide_drive_t *drive);
 
-int ide_spin_wait_hwgroup (ide_drive_t *drive);
-void ide_timer_expiry (unsigned long data);
-void ide_intr (int irq, void *dev_id, struct pt_regs *regs);
-void do_ide_request (request_queue_t * q);
-void ide_init_subdrivers (void);
+extern int ide_spin_wait_hwgroup(ide_drive_t *);
+extern void ide_timer_expiry(unsigned long);
+extern void ide_intr(int irq, void *dev_id, struct pt_regs *regs);
+extern void do_ide_request(request_queue_t *);
+extern void ide_init_subdrivers(void);
 
 #ifndef _IDE_C
 extern struct block_device_operations ide_fops[];
 extern ide_proc_entry_t generic_subdriver_entries[];
 #endif
 
-int ata_attach(ide_drive_t *drive);
+extern int ata_attach(ide_drive_t *);
 
 #ifdef _IDE_C
 #ifdef CONFIG_BLK_DEV_IDE
-int ideprobe_init (void);
+extern int ideprobe_init(void);
+
+#ifdef CONFIG_BLK_DEV_IDEPCI
+extern void ide_scan_pcibus(int scan_direction) __init;
+#endif /* CONFIG_BLK_DEV_IDEPCI */
+
 #endif /* CONFIG_BLK_DEV_IDE */
 #endif /* _IDE_C */
 
+extern void default_hwif_iops(ide_hwif_t *);
+extern void default_hwif_mmiops(ide_hwif_t *);
+extern void default_hwif_transport(ide_hwif_t *);
+
 int ide_register_driver(ide_driver_t *driver);
 void ide_unregister_driver(ide_driver_t *driver);
 int ide_register_subdriver (ide_drive_t *drive, ide_driver_t *driver, int version);
@@ -1222,85 +1665,113 @@ int ide_unregister_subdriver (ide_drive_t *drive);
 int ide_replace_subdriver(ide_drive_t *drive, const char *driver);
 
 #ifdef CONFIG_BLK_DEV_IDEPCI
+
+#ifdef CONFIG_PROC_FS
+typedef struct ide_pci_host_proc_s {
+	char				*name;
+	u8				set;
+	get_info_t			*get_info;
+	struct proc_dir_entry		*parent;
+	struct ide_pci_host_proc_s	*next;
+} ide_pci_host_proc_t;
+
+void ide_pci_register_host_proc(ide_pci_host_proc_t *);
+#endif /* CONFIG_PROC_FS */
+
 #define ON_BOARD		1
 #define NEVER_BOARD		0
+
 #ifdef CONFIG_BLK_DEV_OFFBOARD
 #  define OFF_BOARD		ON_BOARD
 #else /* CONFIG_BLK_DEV_OFFBOARD */
 #  define OFF_BOARD		NEVER_BOARD
 #endif /* CONFIG_BLK_DEV_OFFBOARD */
 
+#define NODMA 0
+#define NOAUTODMA 1
+#define AUTODMA 2
+#define EOL 255
 
 typedef struct ide_pci_enablebit_s {
-	byte	reg;	/* byte pci reg holding the enable-bit */
-	byte	mask;	/* mask to isolate the enable-bit */
-	byte	val;	/* value of masked reg when "enabled" */
+	u8	reg;	/* byte pci reg holding the enable-bit */
+	u8	mask;	/* mask to isolate the enable-bit */
+	u8	val;	/* value of masked reg when "enabled" */
 } ide_pci_enablebit_t;
 
 typedef struct ide_pci_device_s {
-	ide_pci_devid_t		devid;
+	u16			vendor;
+	u16			device;
 	char			*name;
-	void			(*fixup_device)(struct pci_dev *, struct ide_pci_device_s *);
+	void			(*init_setup)(struct pci_dev *, struct ide_pci_device_s *);
 	unsigned int		(*init_chipset)(struct pci_dev *, const char *);
-	unsigned int		(*ata66_check)(ide_hwif_t *);
-	void			(*init_hwif)(ide_hwif_t *);
-	void			(*dma_init)(ide_hwif_t *, unsigned long);
+	void			(*init_iops)(ide_hwif_t *);
+	void                    (*init_hwif)(ide_hwif_t *);
+	void			(*init_dma)(ide_hwif_t *, unsigned long);
+	u8			channels;
+	u8			autodma;
 	ide_pci_enablebit_t	enablebits[2];
-	byte			bootable;
+	u8			bootable;
 	unsigned int		extra;
+	struct ide_pci_device_s	*next;
 } ide_pci_device_t;
 
 #ifdef LINUX_PCI_H
-extern inline void ide_register_xp_fix(struct pci_dev *dev)
-{
-	int i;
-	unsigned short cmd;
-	unsigned long flags;
-	unsigned long base_address[4] = { 0x1f0, 0x3f4, 0x170, 0x374 };
-
-	local_irq_save(flags);
-	pci_read_config_word(dev, PCI_COMMAND, &cmd);
-	pci_write_config_word(dev, PCI_COMMAND, cmd & ~PCI_COMMAND_IO);
-	for (i=0; i<4; i++) {
-		dev->resource[i].start = 0;
-		dev->resource[i].end = 0;
-		dev->resource[i].flags = 0;
-	}
-	for (i=0; i<4; i++) {
-		dev->resource[i].start = base_address[i];
-		dev->resource[i].flags |= PCI_BASE_ADDRESS_SPACE_IO;
-		pci_write_config_dword(dev,
-			(PCI_BASE_ADDRESS_0 + (i * 4)),
-			dev->resource[i].start);
-	}
-	pci_write_config_word(dev, PCI_COMMAND, cmd);
-	local_irq_restore(flags);
-}
-
-void ide_setup_pci_device(struct pci_dev *dev, ide_pci_device_t *d) __init;
+extern void ide_setup_pci_device(struct pci_dev *, ide_pci_device_t *);
+extern void ide_setup_pci_devices(struct pci_dev *, struct pci_dev *, ide_pci_device_t *);
 #endif /* LINUX_PCI_H */
 
-unsigned long ide_find_free_region (unsigned short size) __init;
-void ide_scan_pcibus (int scan_direction) __init;
-#endif
+#endif /* CONFIG_BLK_DEV_IDEPCI */
+
 #ifdef CONFIG_BLK_DEV_IDEDMA
 #define BAD_DMA_DRIVE		0
 #define GOOD_DMA_DRIVE		1
-int ide_build_dmatable (ide_drive_t *drive, ide_dma_action_t func);
-void ide_destroy_dmatable (ide_drive_t *drive);
-ide_startstop_t ide_dma_intr (ide_drive_t *drive);
-int check_drive_lists (ide_drive_t *drive, int good_bad);
-int report_drive_dmaing (ide_drive_t *drive);
-int ide_dmaproc (ide_dma_action_t func, ide_drive_t *drive);
-int ide_release_dma (ide_hwif_t *hwif);
-void ide_setup_dma (ide_hwif_t *hwif, unsigned long dmabase, unsigned int num_ports) __init;
-unsigned long ide_get_or_set_dma_base (ide_hwif_t *hwif, int extra, const char *name) __init;
-#endif /* CONFIG_BLK_DEV_IDEPCI */
+extern int ide_build_dmatable(ide_drive_t *, struct request *);
+extern void ide_destroy_dmatable(ide_drive_t *);
+extern ide_startstop_t ide_dma_intr(ide_drive_t *);
+extern int ide_release_dma(ide_hwif_t *);
+extern void ide_setup_dma(ide_hwif_t *, unsigned long, unsigned int);
+
+extern int __ide_dma_host_off(ide_drive_t *);
+extern int __ide_dma_off_quietly(ide_drive_t *);
+extern int __ide_dma_off(ide_drive_t *);
+extern int __ide_dma_host_on(ide_drive_t *);
+extern int __ide_dma_on(ide_drive_t *);
+extern int __ide_dma_check(ide_drive_t *);
+extern int __ide_dma_read(ide_drive_t *);
+extern int __ide_dma_write(ide_drive_t *);
+extern int __ide_dma_begin(ide_drive_t *);
+extern int __ide_dma_end(ide_drive_t *);
+extern int __ide_dma_test_irq(ide_drive_t *);
+extern int __ide_dma_bad_drive(ide_drive_t *);
+extern int __ide_dma_good_drive(ide_drive_t *);
+extern int __ide_dma_count(ide_drive_t *);
+extern int __ide_dma_verbose(ide_drive_t *);
+extern int __ide_dma_retune(ide_drive_t *);
+extern int __ide_dma_lostirq(ide_drive_t *);
+extern int __ide_dma_timeout(ide_drive_t *);
+#endif /* CONFIG_BLK_DEV_IDEDMA */
+
+extern void hwif_unregister(ide_hwif_t *);
+
+extern void export_ide_init_queue(ide_drive_t *);
+extern u8 export_probe_for_drive(ide_drive_t *);
+extern int probe_hwif_init(ide_hwif_t *);
+
+static inline void *ide_get_hwifdata (ide_hwif_t * hwif)
+{
+	return hwif->hwif_data;
+}
 
-void hwif_unregister (ide_hwif_t *hwif);
+static inline void ide_set_hwifdata (ide_hwif_t * hwif, void *data)
+{
+	hwif->hwif_data = data;
+}
 
-void export_ide_init_queue (ide_drive_t *drive);
-byte export_probe_for_drive (ide_drive_t *drive);
+/* ide-lib.c */
+extern u8 ide_dma_speed(ide_drive_t *drive, u8 mode);
+extern u8 ide_rate_filter(u8 mode, u8 speed); 
+extern int ide_dma_enable(ide_drive_t *drive);
+extern char *ide_xfer_verbose(u8 xfer_rate);
 
 extern spinlock_t ide_lock;