| Age | Commit message (Collapse) | Author |
|---|
|
The current set of DMI board IDs from the fixes branch is required to
reorder them in the for-next branch.
|
|
Currently, the oxpec driver contains Ayaneo devices. Move them to the
new ayaneo-ec driver, which is dedicated to them.
As this driver supports charge inhibition for Ayaneo, add support for it
for the AIR, AIR 1S, AB05-Medoncino, AIR Pro, and Kun, referenced from
the out-of-tree ayaneo-platform driver.
In addition, update the readmes of oxpec to reflect this change.
Link: https://github.com/ShadowBlip/ayaneo-platform
Tested-by: Derek J. Clark <derekjohn.clark@gmail.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://patch.msgid.link/20251119174505.597218-6-lkml@antheas.dev
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Ayaneo devices support charge inhibition via the EC. This inhibition
only works while the device is powered on, and resets between restarts.
However, it is maintained across suspend/resume cycles.
The EC does not support charge threshold control. Instead, userspace
software on Windows manually toggles charge inhibition depending on
battery level.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://patch.msgid.link/20251119174505.597218-4-lkml@antheas.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add hwmon single fan sensor reads and control for Ayaneo devices.
The register and method of access is the same for all devices.
Reviewed-by: Armin-Wolf <W_Armin@gmx.de>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://patch.msgid.link/20251119174505.597218-3-lkml@antheas.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Recent Ayaneo devices feature an ACPI mapped Embedded Controller (EC)
with standard addresses across models that provides access to fan
speed, fan control, battery charge limits, and controller power
controls. Introduce a new driver stub that will handle these driver
features.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://patch.msgid.link/20251119174505.597218-2-lkml@antheas.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Move the WMI core code into a separate directory to prepare for
future additions to the WMI driver. Also update the description
of the Kconfig entry to better fit with the other subsystem
Kconfig entries.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20251111131125.3379-5-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
With the existence of the asus-armoury module the attributes no longer
need to live under the /sys/devices/platform/asus-nb-wmi/ path.
Deprecate all those that were implemented in asus-bioscfg with the goal
of removing them fully in the next LTS cycle.
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20251102215319.3126879-8-denis.benato@linux.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The fw_attributes_class provides a much cleaner interface to all of the
attributes introduced to asus-wmi. This patch moves all of these extra
attributes over to fw_attributes_class, and shifts the bulk of these
definitions to a new kernel module to reduce the clutter of asus-wmi
with the intention of deprecating the asus-wmi attributes in future.
The work applies only to WMI methods which don't have a clearly defined
place within the sysfs and as a result ended up lumped together in
/sys/devices/platform/asus-nb-wmi/ with no standard API.
Where possible the fw attrs now implement defaults, min, max, scalar,
choices, etc. As en example dgpu_disable becomes:
/sys/class/firmware-attributes/asus-armoury/attributes/dgpu_disable/
├── current_value
├── display_name
├── possible_values
└── type
as do other attributes.
Co-developed-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://patch.msgid.link/20251102215319.3126879-3-denis.benato@linux.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
It turns out that the GUID used by the msi-wmi-platform driver
(ABBC0F60-8EA1-11D1-00A0-C90629100000) is not unique, but was instead
copied from the WIndows Driver Samples. This means that this driver
could load on devices from other manufacturers that also copied this
GUID, potentially causing hardware errors.
Prevent this by only loading on devices whitelisted via DMI. The DMI
matches where taken from the msi-ec driver.
Reported-by: Antheas Kapenekakis <lkml@antheas.dev>
Fixes: 9c0beb6b29e7 ("platform/x86: wmi: Add MSI WMI Platform driver")
Tested-by: Antheas Kapenekakis <lkml@antheas.dev>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20251110111253.16204-2-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add a new driver for Uniwill laptops. The driver uses a ACPI
interface to talk with the embedded controller, but relies on a
ACPI WMI interface for receiving event notifications.
The driver is reverse-engineered based on the following information:
- OEM software from intel
- https://github.com/pobrn/qc71_laptop
- https://gitlab.com/tuxedocomputers/development/packages/tuxedo-drivers
- https://github.com/tuxedocomputers/tuxedo-control-center
The underlying EC supports various features, including hwmon sensors,
battery charge limiting, a RGB lightbar and keyboard-related controls.
Reported-by: cyear <chumuzero@gmail.com>
Closes: https://github.com/lm-sensors/lm-sensors/issues/508
Closes: https://github.com/Wer-Wolf/uniwill-laptop/issues/3
Tested-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20251102172942.17879-2-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Fixed a misspelling of Xiaomi.
Signed-off-by: Lazar Aleksic <kripticni.dev@gmail.com>
Link: https://patch.msgid.link/20251028180956.10753-1-kripticni.dev@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
This driver implements support for various Fn keys (like Cut) and Xiaomi
specific AI button.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Gladyshev Ilya <foxido@foxido.dev>
Link: https://lore.kernel.org/r/20250820174140.41410-1-foxido@foxido.dev
[ij: use BIT(8) instead of 0x00000100]
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Support the newly introduced charge_types sysfs attribute as a
replacement for the custom `battery_life_extender` attribute. Setting
charge_types to `Long Life` enables battery life extending mode.
This change is similar to the recent Ideapad patch adding support for
charge_types.
Signed-off-by: Jelle van der Waa <jvanderwaa@redhat.com>
Link: https://lore.kernel.org/r/20250702182844.107706-1-jvanderwaa@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
When multiple WMI devices with the same GUID are present
inside a given system, the WMI driver core might fail to
register all of them.
Consider the following scenario:
WMI devices (<GUID>[-<ID>]):
05901221-D566-11D1-B2F0-00A0C9062910 (on PNP0C14:00)
05901221-D566-11D1-B2F0-00A0C9062910-1 (on PNP0C14:01)
If the WMI core driver somehow unbinds from PNP0C14:00, the following
will happen upon rebinding:
1. The WMI driver core counts all registered WMI devices with a GUID
of 05901221-D566-11D1-B2F0-00A0C9062910 (count: 1).
2. The new WMI device will be named
"05901221-D566-11D1-B2F0-00A0C9062910-1" because another device
with the same GUID is already registered (on PNP0C14:01).
3. The new WMI device cannot be registered due to a name conflict.
Use a IDA when building the WMI device name to avoid such name
collisions by ensuring that a given WMI device ID is not reused.
Userspace applications using udev for WMI device detection are not
impacted by this change. Additionally userspace applications that do
fully support the existing naming scheme are also not impacted. Only
userspace applications using hardcoded sysfs paths will break.
Introduce a kconfig option for restoring the old naming scheme to
give developers time to fix any compatibility issues.
Tested on a Asus Prime B650-Plus.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20250610055526.23688-2-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Create lenovo subdirectory for holding Lenovo specific drivers.
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250610192830.1731454-2-mpearson-lenovo@squebb.ca
[ij: put depends on DMI back, fix trailing empty lines.]
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Fix issues reported by kernel test robot.
- Require DMI for think-lmi.
- Check return from getting serial string
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202506062319.F0IpDxF6-lkp@intel.com/
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250610192830.1731454-1-mpearson-lenovo@squebb.ca
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Adds a driver for the ITE Embedded Controller (EC) on Portwell boards.
It integrates with the Linux GPIO and watchdog subsystems to provide:
- Control/monitoring of up to 8 EC GPIO pins.
- Hardware watchdog timer with 1-255 second timeouts.
The driver communicates with the EC via I/O port 0xe300 and identifies
the hardware by the "PWG" firmware signature. This enables enhanced
system management for Portwell embedded/industrial platforms.
Signed-off-by: Yen-Chi Huang <jesse.huang@portwell.com.tw>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/a04be962-b207-4085-af5b-523f59bffcbc@portwell.com.tw
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The TUXEDO Sirius 16 Gen1 and TUXEDO Sirius 16 Gen2 devices have a per-key
controllable RGB keyboard backlight. The firmware API for it is implemented
via WMI.
To make the backlight userspace configurable this driver emulates a
LampArray HID device and translates the input from hidraw to the
corresponding WMI calls. This is a new approach as the leds subsystem lacks
a suitable UAPI for per-key keyboard backlights, and like this no new UAPI
needs to be established.
The handle_* functions an corresponding structs are named based on the HID
spec: HID Usage Tables 1.6 -> 26 Lighting And Illumination Page (0x59)
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://lore.kernel.org/r/20250425210043.342288-2-wse@tuxedocomputers.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Introduce a driver for devices running Dasharo firmware. The driver
supports thermal monitoring using a new ACPI interface in Dasharo. The
initial version supports monitoring fan speeds, fan PWM duty cycles and
system temperatures as well as determining which specific interfaces are
implemented by firmware.
It has been tested on a NovaCustom laptop running pre-release Dasharo
firmware, which implements fan and thermal monitoring for the CPU and
the discrete GPU, if present.
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Link: https://lore.kernel.org/all/20250507075214.36729-1-lukas.bulwahn@redhat.com
Link: https://lore.kernel.org/r/20250425112147.69308-2-michal.kopec@3mdeb.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
With the X1 (AMD), OneXPlayer added a charge limit and charge inhibit
feature to their devices. Charge limit allows for choosing an arbitrary
battery charge setpoint in percentages. Charge ihibit allows to instruct
the device to stop charging either when it is awake or always.
This feature was then extended for the F1Pro as well. OneXPlayer also
released BIOS updates for the X1 Mini, X1 (Intel), and F1 devices that
add support for this feature. Therefore, enable it for all F1 and
X1 devices.
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Derek J. Clark <derekjohn.clark@gmail.com>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://lore.kernel.org/r/20250425111821.88746-15-lkml@antheas.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The EC of OneXPlayer devices used to only control the fan. This is no
longer the case, with the EC of OneXPlayer gaining additional
functionality (turbo button, turbo led, battery controls).
As it will be beneficial from a complexity perspective to retain this
driver as a single unit, move it out of hwmon, and into platform/x86.
Also, remove the hwmon documentation to prepare moving it to
Documentation/ABI/.
While at it, add myself to the maintainer's file.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Derek J. Clark <derekjohn.clark@gmail.com>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://lore.kernel.org/r/20250425111821.88746-4-lkml@antheas.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Implement Lenovo utility data WMI calls needed to make LEDs
work on Ideapads that support this GUID.
This enables the mic and audio LEDs to be updated correctly.
Tested on below samples.
ThinkBook 13X Gen4 IMH
ThinkBook 14 G6 ABP
ThinkBook 16p Gen4-21J8
ThinkBook 16 G8 IRL
ThinkBook 16 G7+ ASP
Signed-off-by: Jackie Dong <xy-jackie@139.com>
Suggested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20250222114532.4105-1-xy-jackie@139.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add a new driver for Samsung Galaxy Book series notebook devices with the
following features:
- Keyboard backlight control
- Battery hook for installing power supply extension to add charge
control end threshold
- Controller for Samsung's performance modes using the platform profile
interface
- Adds firmware-attributes to control various system features
- Handles various hotkeys and notifications
Signed-off-by: Joshua Grisham <josh@joshuagrisham.com>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20250201105450.193450-1-josh@joshuagrisham.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Move 'mlx-platform' driver 'x86' to 'mellanox' folder.
Motivation to allow running it on systems with ARM architecture.
Since drivers/platform/x86/mlx-platform.c is rellocated to folder
drivers/platform/x86/, remove "MELLANOX PLATFORM DRIVER" item.
This driver will be located under "MELLANOX HARDWARE PLATFORM SUPPORT"
item.
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20250124172632.22437-2-vadimp@nvidia.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The embedded controller code is mainly used on x86 laptops and cannot
work without PC style I/O port access.
Make this a user-visible configuration option that is default enabled
on x86 but otherwise disabled, and that can never be enabled unless
CONFIG_HAS_IOPORT is also available.
The empty stubs in internal.h help ignore the EC code in configurations
that don't support it. In order to see those stubs, the sbshc code also
has to include this header and drop duplicate declarations.
All the direct callers of ec_read/ec_write already had an x86
dependency and now also need to depend on APCI_EC.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241011061948.3211423-1-arnd@kernel.org
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Change the Kconfig dependency so that it doesn't require both I2C and SPI
subsystems to be built. Make a few small changes to the code so that the
code for a bus is only called if the bus is being built.
When SPI support was added to serial-multi-instantiate it created a
dependency that both CONFIG_I2C and CONFIG_SPI must be enabled.
Typically they are, but there's no reason why this should be a
requirement. A specific kernel build could have only I2C devices
or only SPI devices. It should be possible to use serial-multi-instantiate
if only I2C or only SPI is enabled.
The dependency formula used is:
depends on (I2C && !SPI) || (!I2C && SPI) || (I2C && SPI)
The advantage of this approach is that if I2C=m or SPI=m then
SERIAL_MULTI_INSTANTIATE is limited to n/m.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240814132939.308696-1-rf@opensource.cirrus.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Some models need to trigger the EC after each YMC event for the yoga
mode control to work properly. EC triggering consist of a VPC call from
the lenovo-ymc module. Except for this, all VPC calls are in the
ideapad-laptop module.
Since ideapad-laptop has a notification chain, a new YMC_EVENT action
can be added and triggered from the lenovo-ymc module. Then the
ideapad-laptop can trigger the EC.
If the triggering is in the ideapad-laptop module, then the ec_trigger
module parameter should be there as well.
Move the ymc_trigger_ec functionality and the ec_trigger module
parameter to the ideapad-laptop module.
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/d980ab3ac32b5e554f456b0ff17279bfdbe2a203.1721898747.git.soyer@irl.hu
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
This driver uses the extcon subsystem and fails to build
when it cannot call into that subsystem:
x86_64-linux-ld: vmlinux.o: in function `yt2_1380_fc_worker':
lenovo-yoga-tab2-pro-1380-fastcharger.c:(.text+0xa9d819): undefined reference to `extcon_get_state'
x86_64-linux-ld: lenovo-yoga-tab2-pro-1380-fastcharger.c:(.text+0xa9d853): undefined reference to `extcon_get_state'
x86_64-linux-ld: vmlinux.o: in function `yt2_1380_fc_serdev_probe':
lenovo-yoga-tab2-pro-1380-fastcharger.c:(.text+0xa9da22): undefined reference to `extcon_get_extcon_dev'
x86_64-linux-ld: lenovo-yoga-tab2-pro-1380-fastcharger.c:(.text+0xa9dc0c): undefined reference to `devm_extcon_register_notifier_all'
Add a Kconfig dependency to make it it always builds correctly.
Fixes: b2ed33e8d486 ("platform/x86: Add lenovo-yoga-tab2-pro-1380-fastcharger driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240528115940.3169455-1-arnd@kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Now that drivers/platform/x86/thinkpad_acpi.c uses
sparse_keymap_report_event(), it must select INPUT_SPARSEKMAP in its
Kconfig option otherwise the build fails with:
ld: vmlinux.o: in function `tpacpi_input_send_key':
thinkpad_acpi.c:(.text+0xd4d27f): undefined reference to `sparse_keymap_report_event'
ld: vmlinux.o: in function `hotkey_init':
thinkpad_acpi.c:(.init.text+0x66cb6): undefined reference to `sparse_keymap_setup'
Fixes: 42f7b965de9d ("platform/x86: thinkpad_acpi: Switch to using sparse-keymap helpers")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240522074813.379b9fc2@gandalf.local.home
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Some MeeGoPad top-set boxes have an ANX7428 Type-C Switch for USB3.1 Gen 1
and DisplayPort over Type-C alternate mode support.
The ANX7428 has a microcontroller which takes care of the PD negotiation
and automatically sets the builtin Crosspoint Switch to send the right
signal to the 4 highspeed pairs of the Type-C connector. It also takes
care of HPD and AUX channel routing for DP alternate mode.
IOW the ANX7428 operates fully autonomous and to the x5-Z8350 SoC
things look like there simple is a USB-3 Type-A connector and a
separate DisplayPort connector. Except that the BIOS does not
power on the ANX7428 at boot (meh).
Add a driver to power on the ANX7428. This driver is added under
drivers/platform/x86 rather than under drivers/usb/typec for 2 reasons:
1. This driver is specifically written to work with how the ANX7428 is
described in the ACPI tables of the MeeGoPad x86 (Cherry Trail) devices.
2. This driver only powers on the ANX7428 and does not do anything wrt
its Type-C functionality. It should be possible to tell the controller
which data- and/or power-role to negotiate and to swap the role(s) after
negotiation but the MeeGoPad top-set boxes always draw their power from
a separate power-connector and they only support USB host-mode. So this
functionality is unnecessary and due to lack of documentation this is
tricky to support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240514180343.70795-1-hdegoede@redhat.com
|
|
Add a new driver for the custom fast charging protocol found on Lenovo Yoga
Tablet 2 1380F / 1380L models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240422131649.46002-1-hdegoede@redhat.com
|
|
Add a new driver for the MSI WMI Platform interface. The underlying
ACPI WMI interface supports many features, but so far only reading
of fan speed sensors is implemented.
The driver was reverse-engineered based on a user request to the
lm-sensors project, see the github issue for details.
The ACPI WMI interface used by this driver seems to use the same
embedded controller interface as the msi-ec driver, but supports
automatic discovery of supported machines without relying on a
DMI whitelist.
The driver was tested by the user who created the github issue.
Closes: https://github.com/lm-sensors/lm-sensors/issues/475
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20240421191145.3189-1-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The new driver Kconfig entry has a typo that causes a link failure
when CONFIG_INPUT_SPARSEKMAP is disabled:
x86_64-linux-ld: drivers/platform/x86/quickstart.o: in function `quickstart_notify':
quickstart.c:(.text+0x96): undefined reference to `sparse_keymap_report_event'
x86_64-linux-ld: drivers/platform/x86/quickstart.o: in function `quickstart_probe':
quickstart.c:(.text+0x1da): undefined reference to `sparse_keymap_setup'
Select this symbol instead of the incorrect INPUT_SPARSE_KEYMAP.
Fixes: afd66f2a739e ("platform/x86: Add ACPI quickstart button (PNP0C32) driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: https://lore.kernel.org/r/20240404123435.2684819-1-arnd@kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This drivers supports the ACPI quickstart button device, which
is used to send manufacturer-specific events to userspace.
Since the meaning of those events is not standardized, userspace
has to use for example hwdb to decode them.
The driver itself is based on an earlier proposal, but contains
some improvements and uses the device wakeup API instead of a
custom sysfs file.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240131111641.4418-2-W_Armin@gmx.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add lenovo WMI camera button driver to support camera button.
The Camera button is a GPIO device. This driver receives ACPI notifications
when the camera button is switched on/off. This driver is used in
Lenovo A70, it is a Computer integrated machine.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Link: https://lore.kernel.org/r/20240327082737.336992-1-aichao@kylinos.cn
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This patch adds battery charge control support on Fujitsu notebooks
via the S006 method of the FUJ02E3 ACPI device. With this method it's
possible to set charge_control_end_threshold between 50 and 100%.
Tested on Lifebook E5411 and Lifebook U728. Sadly I can't test this
patch on a dual battery one, but I didn't find any clue about
independent battery charge control on dual battery Fujitsu notebooks
either. And by that I mean checking the DSDT table of various Lifebook
notebooks and reverse engineering FUJ02E3.dll.
Signed-off-by: Szilard Fabian <szfabian@bluemarch.art>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Link: https://lore.kernel.org/r/20240215203012.228758-2-szfabian@bluemarch.art
[ij: coding style cleanups.]
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Since 64f67b5240db ("leds: trigger: audio: Add an activate callback to
ensure the initial brightness is set") the audio triggers have an
activate callback which sets the LED brightness as soon as the
(default) trigger is bound to the LED device. So we can remove the
call to ledtrig_audio_get.
Positive side effect: There's no code dependency to ledtrig-audio any
longer, what allows to remove some Kconfig dependencies.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/daef7331-dcb4-4b3a-802e-656629486b4c@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Back merge pdx86 fixes into pdx86/for-next for further WMI work
depending on some of the fixes.
platform-drivers-x86 for v6.7-3
Highlights:
- asus-wmi: Solve i8042 filter resource handling, input, and
suspend issues
- wmi: Skip zero instance WMI blocks to avoid issues with
some laptops
- mlxbf-bootctl: Differentiate dev/production keys
- platform/surface: Correct serdev related return value to avoid
leaking errno into userspace
- Error checking fixes
The following is an automated shortlog grouped by driver:
asus-wmi:
- Change q500a_i8042_filter() into a generic i8042-filter
- disable USB0 hub on ROG Ally before suspend
- Filter Volume key presses if also reported via atkbd
- Move i8042 filter install to shared asus-wmi code
mellanox:
- Add null pointer checks for devm_kasprintf()
- Check devm_hwmon_device_register_with_groups() return value
mlxbf-bootctl:
- correctly identify secure boot with development keys
surface: aggregator:
- fix recv_buf() return value
wmi:
- Skip blocks with zero instances
|
|
Add Silicom platform (silicom-platform) Linux driver for Swisscom
Business Box (Swisscom BB) as well as Cordoba family products.
This platform driver provides support for various functions via
the Linux LED framework, GPIO framework, Hardware Monitoring (HWMON)
and device attributes.
Signed-off-by: Henry Shi <henryshi2018@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20231124200334.5318-1-henryshi2018@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Support CPU and GPU fan speed monitoring through WMI for Predator
PHN16-71.
Signed-off-by: SungHwan Jung <onenowy@gmail.com>
Link: https://lore.kernel.org/r/20231124094122.100707-3-onenowy@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
"select ACPI_VIDEO" cause recursive dependency when "depends on HWMON"
is added:
drivers/hwmon/Kconfig:6:error: recursive dependency detected!
drivers/hwmon/Kconfig:6: symbol HWMON is selected by EEEPC_LAPTOP
drivers/platform/x86/Kconfig:326: symbol EEEPC_LAPTOP depends on ACPI_VIDEO
drivers/acpi/Kconfig:208: symbol ACPI_VIDEO is selected by ACER_WMI
drivers/platform/x86/Kconfig:173: symbol ACER_WMI depends on HWMON
Replace the select with depends on to avoid this problem when the next
patch in this series adds "depends on HWMON".
There is a stub defined for the used acpi_video_get_backlight_type()
function when ACPI_VIDEO is not set, so use:
depends on ACPI_VIDEO || ACPI_VIDEO = n
Signed-off-by: SungHwan Jung <onenowy@gmail.com>
Link: https://lore.kernel.org/r/20231124094122.100707-4-onenowy@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Predator PHN16-71
The Acer Predator PHN16-71 has the mode key that is used to rotate thermal
modes or toggle turbo mode with predator sense app (ver. 4) on windows.
This patch includes platform profile and the mode key support for the
device and also includes a small fix for "WMI_gaming_execute_u64"
function.
Signed-off-by: SungHwan Jung <onenowy@gmail.com>
Link: https://lore.kernel.org/r/20231124094122.100707-2-onenowy@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
asus-nb-wmi calls i8042_install_filter() in some cases, but it never
calls i8042_remove_filter(). This means that a dangling pointer to
the filter function is left after rmmod leading to crashes.
Fix this by moving the i8042-filter installation to the shared
asus-wmi code and also remove it from the shared code on driver unbind.
Fixes: b5643539b825 ("platform/x86: asus-wmi: Filter buggy scan codes on ASUS Q500A")
Cc: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231120154235.610808-2-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add support for Inspur platforms to used the platform profile feature.
This will allow users to determine and control the platform modes
between low-power, balanced and performance modes.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231020024007.1677962-1-aichao@kylinos.cn
[ij: Removed kerneldoc markers from non-kerneldoc comments.]
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add dependency on PCI to avoid 'mlx-platform' compilation error in case
CONFIG_PCI is not set.
Failed on i386:
CONFIG_ACPI=y
CONFIG_ISA=y
Error In function 'mlxplat_pci_fpga_device_init':
implicit declaration of function 'pci_request_region':
6204 | err = pci_request_region(pci_dev, 0, res_name);
| ^~~~~~~~~~~~~~~~~~
| pci_request_regions
Fixes: 1316e0af2dc0 ("platform: mellanox: mlx-platform: Introduce ACPI init flow")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20230829133748.58208-2-vadimp@nvidia.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The P2SB is used purely as a library and all users must select it with
depends on PCI
select P2SB if X86
statement. Without this the combination of different configuration
options may lead to build failures.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230822142514.2140897-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Introduce support for ACPI initialization flow - add ACPI match hook.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230822113451.13785-12-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Immutable branch between pdx86 simatic branch and LED due for the v6.6 merge window
ib-pdx86-simatic-v6.6-2: v6.5-rc1 + ib-pdx86-simatic-v6.6 +
more recent pdx86 simatic-ipc patches for merging into
the LED subsystem for v6.6.
|
|
With more files around move everything to a subdirectory. Users will
only see the several options once they enable the main one.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230719153518.13073-4-henning.schild@siemens.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add a driver for Schweitzer Engineering Laboratories SEL-3350 computers
front LEDs and power supplies. LED and power supply status is provided
by the Intel SoC GPIO.
Signed-off-by: Robert Joslyn <robert.joslyn@redrectangle.org>
Link: https://lore.kernel.org/r/20230713035714.807819-1-robert.joslyn@redrectangle.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
