| Age | Commit message (Collapse) | Author |
|---|
|
Teach the memory hotplug path to tear down KASAN shadow that
was mapped during early boot when a memory block is offlined.
Track for each sclp_mem whether its range was covered by the early
KASAN shadow via an early_shadow_mapped flag. When such a block is
deconfigured and removed via sclp_config_mem_store(), compute the
corresponding shadow range and call vmemmap_free() to unmap the
boot mapped shadow, then clear the flag.
Using vmemmap_free() for the early shadow is safe despite the use
of large mappings in the boot-time KASAN setup. The initial shadow
is mapped with 1M and 2G pages, where possible. The minimum hotplug
memory block size is 128M and always aligned (the identity mapping
is at least 2G aligned), which corresponds to a 16M chunk of at
least 1M aligned shadow. PMD-mapped 1M shadow pages therefore
never need splitting, and PUD-mapped 2G shadow pages can now be
split following the preceding changes.
Relax the modify_pagetable() sanity check in vmem so that, with
KASAN enabled, it may also operate on the KASAN shadow region in
addition to the 1:1 mapping and vmemmap area. This allows the KASAN
shadow unmapping to reuse the common vmem helpers.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Use scnprintf() instead of sprintf() for those cases where the destination
is an array and the size of the array is known at compile time.
This prevents theoretical buffer overflows, but also avoids that people
again and again spend time to figure out if the code is actually safe.
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
"__vmalloc()/kvmalloc() and no-block support" (Uladzislau Rezki)
Rework the vmalloc() code to support non-blocking allocations
(GFP_ATOIC, GFP_NOWAIT)
"ksm: fix exec/fork inheritance" (xu xin)
Fix a rare case where the KSM MMF_VM_MERGE_ANY prctl state is not
inherited across fork/exec
"mm/zswap: misc cleanup of code and documentations" (SeongJae Park)
Some light maintenance work on the zswap code
"mm/page_owner: add debugfs files 'show_handles' and 'show_stacks_handles'" (Mauricio Faria de Oliveira)
Enhance the /sys/kernel/debug/page_owner debug feature by adding
unique identifiers to differentiate the various stack traces so
that userspace monitoring tools can better match stack traces over
time
"mm/page_alloc: pcp->batch cleanups" (Joshua Hahn)
Minor alterations to the page allocator's per-cpu-pages feature
"Improve UFFDIO_MOVE scalability by removing anon_vma lock" (Lokesh Gidra)
Address a scalability issue in userfaultfd's UFFDIO_MOVE operation
"kasan: cleanups for kasan_enabled() checks" (Sabyrzhan Tasbolatov)
"drivers/base/node: fold node register and unregister functions" (Donet Tom)
Clean up the NUMA node handling code a little
"mm: some optimizations for prot numa" (Kefeng Wang)
Cleanups and small optimizations to the NUMA allocation hinting
code
"mm/page_alloc: Batch callers of free_pcppages_bulk" (Joshua Hahn)
Address long lock hold times at boot on large machines. These were
causing (harmless) softlockup warnings
"optimize the logic for handling dirty file folios during reclaim" (Baolin Wang)
Remove some now-unnecessary work from page reclaim
"mm/damon: allow DAMOS auto-tuned for per-memcg per-node memory usage" (SeongJae Park)
Enhance the DAMOS auto-tuning feature
"mm/damon: fixes for address alignment issues in DAMON_LRU_SORT and DAMON_RECLAIM" (Quanmin Yan)
Fix DAMON_LRU_SORT and DAMON_RECLAIM with certain userspace
configuration
"expand mmap_prepare functionality, port more users" (Lorenzo Stoakes)
Enhance the new(ish) file_operations.mmap_prepare() method and port
additional callsites from the old ->mmap() over to ->mmap_prepare()
"Fix stale IOTLB entries for kernel address space" (Lu Baolu)
Fix a bug (and possible security issue on non-x86) in the IOMMU
code. In some situations the IOMMU could be left hanging onto a
stale kernel pagetable entry
"mm/huge_memory: cleanup __split_unmapped_folio()" (Wei Yang)
Clean up and optimize the folio splitting code
"mm, swap: misc cleanup and bugfix" (Kairui Song)
Some cleanups and a minor fix in the swap discard code
"mm/damon: misc documentation fixups" (SeongJae Park)
"mm/damon: support pin-point targets removal" (SeongJae Park)
Permit userspace to remove a specific monitoring target in the
middle of the current targets list
"mm: MISC follow-up patches for linux/pgalloc.h" (Harry Yoo)
A couple of cleanups related to mm header file inclusion
"mm/swapfile.c: select swap devices of default priority round robin" (Baoquan He)
improve the selection of swap devices for NUMA machines
"mm: Convert memory block states (MEM_*) macros to enums" (Israel Batista)
Change the memory block labels from macros to enums so they will
appear in kernel debug info
"ksm: perform a range-walk to jump over holes in break_ksm" (Pedro Demarchi Gomes)
Address an inefficiency when KSM unmerges an address range
"mm/damon/tests: fix memory bugs in kunit tests" (SeongJae Park)
Fix leaks and unhandled malloc() failures in DAMON userspace unit
tests
"some cleanups for pageout()" (Baolin Wang)
Clean up a couple of minor things in the page scanner's
writeback-for-eviction code
"mm/hugetlb: refactor sysfs/sysctl interfaces" (Hui Zhu)
Move hugetlb's sysfs/sysctl handling code into a new file
"introduce VM_MAYBE_GUARD and make it sticky" (Lorenzo Stoakes)
Make the VMA guard regions available in /proc/pid/smaps and
improves the mergeability of guarded VMAs
"mm: perform guard region install/remove under VMA lock" (Lorenzo Stoakes)
Reduce mmap lock contention for callers performing VMA guard region
operations
"vma_start_write_killable" (Matthew Wilcox)
Start work on permitting applications to be killed when they are
waiting on a read_lock on the VMA lock
"mm/damon/tests: add more tests for online parameters commit" (SeongJae Park)
Add additional userspace testing of DAMON's "commit" feature
"mm/damon: misc cleanups" (SeongJae Park)
"make VM_SOFTDIRTY a sticky VMA flag" (Lorenzo Stoakes)
Address the possible loss of a VMA's VM_SOFTDIRTY flag when that
VMA is merged with another
"mm: support device-private THP" (Balbir Singh)
Introduce support for Transparent Huge Page (THP) migration in zone
device-private memory
"Optimize folio split in memory failure" (Zi Yan)
"mm/huge_memory: Define split_type and consolidate split support checks" (Wei Yang)
Some more cleanups in the folio splitting code
"mm: remove is_swap_[pte, pmd]() + non-swap entries, introduce leaf entries" (Lorenzo Stoakes)
Clean up our handling of pagetable leaf entries by introducing the
concept of 'software leaf entries', of type softleaf_t
"reparent the THP split queue" (Muchun Song)
Reparent the THP split queue to its parent memcg. This is in
preparation for addressing the long-standing "dying memcg" problem,
wherein dead memcg's linger for too long, consuming memory
resources
"unify PMD scan results and remove redundant cleanup" (Wei Yang)
A little cleanup in the hugepage collapse code
"zram: introduce writeback bio batching" (Sergey Senozhatsky)
Improve zram writeback efficiency by introducing batched bio
writeback support
"memcg: cleanup the memcg stats interfaces" (Shakeel Butt)
Clean up our handling of the interrupt safety of some memcg stats
"make vmalloc gfp flags usage more apparent" (Vishal Moola)
Clean up vmalloc's handling of incoming GFP flags
"mm: Add soft-dirty and uffd-wp support for RISC-V" (Chunyan Zhang)
Teach soft dirty and userfaultfd write protect tracking to use
RISC-V's Svrsw60t59b extension
"mm: swap: small fixes and comment cleanups" (Youngjun Park)
Fix a small bug and clean up some of the swap code
"initial work on making VMA flags a bitmap" (Lorenzo Stoakes)
Start work on converting the vma struct's flags to a bitmap, so we
stop running out of them, especially on 32-bit
"mm/swapfile: fix and cleanup swap list iterations" (Youngjun Park)
Address a possible bug in the swap discard code and clean things
up a little
[ This merge also reverts commit ebb9aeb980e5 ("vfio/nvgrace-gpu:
register device memory for poison handling") because it looks
broken to me, I've asked for clarification - Linus ]
* tag 'mm-stable-2025-12-03-21-26' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (321 commits)
mm: fix vma_start_write_killable() signal handling
mm/swapfile: use plist_for_each_entry in __folio_throttle_swaprate
mm/swapfile: fix list iteration when next node is removed during discard
fs/proc/task_mmu.c: fix make_uffd_wp_huge_pte() huge pte handling
mm/kfence: add reboot notifier to disable KFENCE on shutdown
memcg: remove inc/dec_lruvec_kmem_state helpers
selftests/mm/uffd: initialize char variable to Null
mm: fix DEBUG_RODATA_TEST indentation in Kconfig
mm: introduce VMA flags bitmap type
tools/testing/vma: eliminate dependency on vma->__vm_flags
mm: simplify and rename mm flags function for clarity
mm: declare VMA flags by bit
zram: fix a spelling mistake
mm/page_alloc: optimize lowmem_reserve max lookup using its semantic monotonicity
mm/vmscan: skip increasing kswapd_failures when reclaim was boosted
pagemap: update BUDDY flag documentation
mm: swap: remove scan_swap_map_slots() references from comments
mm: swap: change swap_alloc_slow() to void
mm, swap: remove redundant comment for read_swap_cache_async
mm, swap: use SWP_SOLIDSTATE to determine if swap is rotational
...
|
|
The KMSG_COMPONENT macro is a leftover of the s390 specific "kernel
message catalog" which never made it upstream.
Remove the macro in order to get rid of a pointless indirection. Replace
all users with the string it defines. In almost all cases this leads to a
simple replacement like this:
- #define KMSG_COMPONENT "appldata"
- #define pr_fmt(fmt) KMSG_COMPONENT ": " fmt
+ #define pr_fmt(fmt) "appldata: " fmt
Except for some special cases this is just mechanical/scripted work.
Acked-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
There shouldn't be any 31 bit code around anymore that matters.
Remove the compat layer support required to run 31 bit code.
Reason for removal is code simplification and reduced test effort.
Note that this comes without any deprecation warnings added to config
options, or kernel messages, since most likely those would be ignored
anyway.
If it turns out there is still a reason to keep the compat layer this
can be reverted at any time in the future.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
For now, including <asm/pgalloc.h> instead of <linux/pgalloc.h> is
technically fine unless the .c file calls p*d_populate_kernel() helper
functions.
But it is a better practice to always include <linux/pgalloc.h>. Include
<linux/pgalloc.h> instead of <asm/pgalloc.h> outside arch/.
Link: https://lkml.kernel.org/r/20251024113047.119058-3-harry.yoo@oracle.com
Signed-off-by: Harry Yoo <harry.yoo@oracle.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: SeongJae Park <sj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
When the global kernel command line parameter
memory_hotplug.memmap_on_memory is set to false, per-memory-block
memmap_on_memory setting can still be set to true. However, when
configuring memory block, add_memory_resource() would configure it
without memmap_on_memory.
i.e.
Even if the MHP_MEMMAP_ON_MEMORY flag is set,
mhp_supports_memmap_on_memory() returns false unless the kernel command
line parameter "memory_hotplug.memmap_on_memory" is enabled. When both
the flag and the cmdline parameter are set, the memory block can be
configured with or without memmap_on_memory support.
To ensure consistent behavior, permit configuring per-memory-block
memmap_on_memory only when the memory_hotplug.memmap_on_memory kernel
command line parameter is enabled.
This is similar to commit 73954d379efd ("dax: add a sysfs knob to
control memmap_on_memory behavior")
Fixes: ff18dcb19aab ("s390/sclp: Add support for dynamic (de)configuration of memory")
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Jan Höppner says:
====================
The tape device driver is limited to a block size of 65535 bytes since a
single CCW can only transfer up to 64K-1 bytes (The count field is a
16bit value). This series introduces data chaining for all read/write
functions to support block sizes larger than 65535.
The tape device type 3490 (emulated) and 3590/3592 can handle up to
256K. [1]
[1] https://www.ibm.com/docs/en/zos/3.1.0?topic=blksize-system-determined-block-size
====================
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The tape device type 3590/3592 and emulated 3490 VTS can handle a block
size of up to 256K bytes. Currently the tape device driver is limited to
a block size of 65535 bytes (64K-1). This limitation stems from the
maximum of 65535 bytes of data that can be transferred with one
Channel-Command Word (CCW).
To work around this limitation data chaining is used which uses several
CCW to transfer an entire 256K block of data. A single CCW holds a
maximum of 65535 bytes of data.
Set MAX_BLOCKSIZE to 262144 (= 256K) to allow for data transfers with
larger block sizes. The read_block() and write_block() discipline
functions calculate the number of CCWs required based on the IDAL buffer
array size that was created for a given block size. If there is more
than one CCW required for the data transfer, the new helper function
tape_ccw_dc_idal() is used to build the data chain accordingly.
The Interruption-Repsonse Block (irb) is added to the tape_request
struct so that the tapechar_read/write() functions can analyze what data
was read or written accordingly.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The tape device driver uses a single idal_buffer for I/O. While the
buffer itself can be arbitrary big, the limit for data transfer for a
single Channel-Command Word is at 65535 bytes (64K-1) since the count
field specifying the amount of data designated by the CCW is a 16-bit
unsigned value.
Provide functionality that allocates an array of multiple IDAL buffer
with the limitation mentioned above in mind.
A call to idal_buffer_array_alloc() allocates an array with a certain
amount of IDAL buffers which is determined based on the total size of
@size. Each individual buffer is limited to a size of CCW_MAX_BYTE_COUNT
(65535 bytes).
Add helper functions that determine the size (# of elements) and the
total data size covered by the array as well.
Current users of the single IDAL buffer are adapted to use the new
functions with one buffer to allocate.
The single IDAL buffer is removed from the tape_char_data struct.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Currently tapechar_check_idalbuffer() is part of tape_char.c and is used
to ensure the idal buffer is big enough for the requested I/O and
reallocates a new one if required. The same is done in tape_std.c when a
fixed block size is set using the mtsetblk command. This is essentially
duplicate code.
The allocation of the buffer that is required for I/O can be considered
core functionality. Move the idal buffer allocation to tape_core.c,
make it generally available, and reduce code duplication.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
In contrast to all other helper functions used to build CCW chains,
tape_ccw_cc_idal() and tape_ccw_end_idal() return values using
post-increments, which results in returning the same CCW pointer.
Though, the intent of the CCW helper functions is to return the _next_
CCW in the chain, which can then be processed.
There is currently no actual issue, as tape_ccw_cc_idal() is not used
yet and tape_ccw_end_idal() is only used at the end of a chain.
Change both functions return statement to ccw + 1 and bring them in line
with the other helper functions.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The Read Opposite error recovery code required 2 extra CCWs to be
allocated in order to transform the request. As this error recovery code
for both 34xx and 3590 was removed the additional allocation isn't
required anymore. Reduce it to two.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
On old native type 3590 tape devices a Read Opposite error recovery
procedure on Error Recovery Action Code (ERA) 26 was issued if a Read
Forward command failed. This recovery procedure was implemented with the
Read Backward command. This is no longer supported.
Remove 3590 ERA 26 and Read Backward related recovery code.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
On old native type 3490 tape devices a Read Opposite error recovery
procedure on Error Recovery Action Code (ERA) 26 was issued if a Read
Forward command failed. This recovery procedure was implemented with the
Read Backward command.
As a preparation for a subsequent commit, that adds support for bigger
block sizes, remove the 34xx ERA 26 related recovery code. The recovery
code would need to be adapted to the bigger block sizes, without any
possibility to be tested, as modern Virtual Tape Servers (VTS) do
neither report ERA 26 on a Read Forward command failure nor support the
error recovery procedure anymore.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The count parameter of the read/write_block discipline functions was
never used. Remove it.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Sumanth Korikkar says:
====================
Provide a new interface for dynamic configuration and
deconfiguration of hotplug memory on s390, allowing with/without
memmap_on_memory support. It is a follow up on the discussion with David
when introducing memmap_on_memory support for s390 and support dynamic
(de)configuration of memory:
https://lore.kernel.org/all/ee492da8-74b4-4a97-8b24-73e07257f01d@redhat.com/
https://lore.kernel.org/all/20241202082732.3959803-1-sumanthk@linux.ibm.com/
The original motivation for introducing memmap_on_memory on s390 was to
avoid using online memory to store struct pages metadata, particularly
for standby memory blocks. This became critical in cases where there was
an imbalance between standby and online memory, potentially leading to
boot failures due to insufficient memory for metadata allocation.
To address this, memmap_on_memory was utilized on s390. However, in its
current form, it adds struct pages metadata at the start of each memory
block at the time of addition (only standby memory), and this
configuration is static. It cannot be changed at runtime (When the user
needs continuous physical memory).
Inorder to provide more flexibility to the user and overcome the above
limitation, add an option to dynamically configure and deconfigure
hotpluggable memory block with/without memmap_on_memory.
With the new interface, s390 will not add all possible hotplug memory in
advance, like before, to make it visible in sysfs for online/offline
actions. Instead, before memory block can be set online, it has to be
configured via a new interface in /sys/firmware/memory/memoryX/config,
which makes s390 similar to others. i.e. Adding of hotpluggable memory is
controlled by the user instead of adding it at boottime.
s390 kernel sysfs interface to configure/deconfigure memory with
memmap_on_memory (with upcoming lsmem changes):
* Initial memory layout:
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
* Configure memory
echo 1 > /sys/firmware/memory/memory16/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0x87ffffff 128M offline 16 yes yes
0x88000000-0xffffffff 1.9G offline 17-31 no yes
* Deconfigure memory
echo 0 > /sys/firmware/memory/memory16/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
* Enable memmap_on_memory and online it.
(Deconfigure first)
echo 0 > /sys/devices/system/memory/memory5/online
echo 0 > /sys/firmware/memory/memory5/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x27ffffff 640M online 0-4 yes no
0x28000000-0x2fffffff 128M offline 5 no no
0x30000000-0x7fffffff 1.3G online 6-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
(Enable memmap_on_memory and online it)
echo 1 > /sys/firmware/memory/memory5/memmap_on_memory
echo 1 > /sys/firmware/memory/memory5/config
echo 1 > /sys/devices/system/memory/memory5/online
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x27ffffff 640M online 0-4 yes no
0x28000000-0x2fffffff 128M online 5 yes yes
0x30000000-0x7fffffff 1.3G online 6-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
* Disable memmap_on_memory and online it.
(Deconfigure first)
echo 0 > /sys/devices/system/memory/memory5/online
echo 0 > /sys/firmware/memory/memory5/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x27ffffff 640M online 0-4 yes no
0x28000000-0x2fffffff 128M offline 5 no yes
0x30000000-0x7fffffff 1.3G online 6-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
(Disable memmap_on_memory and online it)
echo 0 > /sys/firmware/memory/memory5/memmap_on_memory
echo 1 > /sys/firmware/memory/memory5/config
echo 1 > /sys/devices/system/memory/memory5/online
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
* Userspace changes:
lsmem/chmem tool is also changed to use the new interface. I will send
it to util-linux soon.
Patch 1 adds support for removal of boot-allocated memory blocks.
Patch 2 provides option to dynamically configure and deconfigure memory
with/without memmap_on_memory.
Patch 3 removes MHP_OFFLINE_INACCESSIBLE from s390. The mhp flag was
used to mark memory as not accessible until memory hotplug online phase
begins. However, with patch 2, it is no longer essential. Memory can be
brought to accessible state before adding memory, as the memory is added
during runttime now instead of boottime.
Patch 4 removes the MEM_PREPARE_ONLINE/MEM_FINISH_OFFLINE notifiers. It
is no longer needed. Memory can be brought to accessible state before
adding memory now, with runtime (de)configuration of memory.
Note: The patches apply to the linux-next branch.
v3:
Thanks David
* Avoid goto label in create_standby_sclp_mems().
* Use unsigned long instead of u64.
* Add Acked-by.
v2:
Thanks David
* Rename struct mblock/mblock_arg with struct sclp_mem/sclp_mem_arg.
* Rename all mblocks/mblock references with sclp_mems/sclp_mem -
structures, functions.
* Rename create_online_mblock() with create_configured_sclp_mem().
* Rename config_mblock_show()/config_mblock_store() with
config_sclp_mem_show()/config_sclp_mem_store().
* Remove contains_standby_increment() and
sclp_mem_notifier. sclp mem state change is performed when
adding/removing memory. sclp memory notifier - no longer needed with
this patchset.
* Recover sclp mem state when add_memory() fails.
* Refactor and add function init_sclp_mem().
* Use unsigned long instead of unsigned long long.
* Simplify and correct kobj handling. Thanks Heiko.
====================
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Use scnprintf() instead of sprintf() for those cases where the destination
is an array and the size of the array is known at compile time.
This prevents theoretical buffer overflows, but also avoids that people
again and again spend time to figure out if the code is actually safe.
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Use scnprintf() instead of sprintf() for those cases where the destination
is an array and the size of the array is known at compile time.
This prevents theoretical buffer overflows, but also avoids that people
again and again spend time to figure out if the code is actually safe.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
mhp_flag MHP_OFFLINE_INACCESSIBLE was used to mark memory as not
accessible until memory hotplug online phase begins.
Earlier, standby memory blocks were added upfront during boottime and
MHP_OFFLINE_INACCESSIBLE flag avoided page_init_poison() on memmap
during mhp addition phase.
However with dynamic runtime configuration of memory, standby memory can
be brought to accessible state before performing add_memory(). Hence,
remove MHP_OFFLINE_INACCESSIBLE.
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Provide a new interface for dynamic configuration and deconfiguration of
hotplug memory, allowing with/without memmap_on_memory support. It is a
follow up on the discussion with David when introducing memmap_on_memory
support for s390 and support dynamic (de)configuration of memory:
https://lore.kernel.org/all/ee492da8-74b4-4a97-8b24-73e07257f01d@redhat.com/
https://lore.kernel.org/all/20241202082732.3959803-1-sumanthk@linux.ibm.com/
The original motivation for introducing memmap_on_memory on s390 was to
avoid using online memory to store struct pages metadata, particularly
for standby memory blocks. This became critical in cases where there was
an imbalance between standby and online memory, potentially leading to
boot failures due to insufficient memory for metadata allocation.
To address this, memmap_on_memory was utilized on s390. However, in its
current form, it adds struct pages metadata at the start of each memory
block at the time of addition and this configuration is static. It
cannot be changed at runtime. (When the user needs continuous physical
memory).
Inorder to provide more flexibility to the user and overcome the above
limitation, add option to dynamically configure and deconfigure
hotpluggable memory block with/without memmap_on_memory.
With the new interface, s390 will not add all possible hotplug memory in
advance, like before, to make it visible in sysfs for online/offline
actions. Instead, before memory block can be set online, it has to be
configured via a new interface in /sys/firmware/memory/memoryX/config,
which makes s390 similar to others. i.e. Adding of hotpluggable memory is
controlled by the user instead of adding it at boottime.
The s390 kernel sysfs interface to configure and deconfigure memory is
as follows (considering the upcoming lsmem changes):
* Initial memory layout:
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
* Configure memory
sys="/sys"
echo 1 > $sys/firmware/memory/memory16/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0x87ffffff 128M offline 16 yes yes
0x88000000-0xffffffff 1.9G offline 17-31 no yes
* Deconfigure memory
echo 0 > $sys/firmware/memory/memory16/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
3. Enable memmap_on_memory and online it.
echo 0 > $sys/devices/system/memory/memory5/online
echo 0 > $sys/firmware/memory/memory5/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x27ffffff 640M online 0-4 yes no
0x28000000-0x2fffffff 128M offline 5 no no
0x30000000-0x7fffffff 1.3G online 6-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
echo 1 > $sys/firmware/memory/memory5/memmap_on_memory
echo 1 > $sys/firmware/memory/memory5/config
echo 1 > $sys/devices/system/memory/memory5/online
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x27ffffff 640M online 0-4 yes no
0x28000000-0x2fffffff 128M online 5 yes yes
0x30000000-0x7fffffff 1.3G online 6-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
4. Disable memmap_on_memory and online it.
echo 0 > $sys/devices/system/memory/memory5/online
echo 0 > $sys/firmware/memory/memory5/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x27ffffff 640M online 0-4 yes no
0x28000000-0x2fffffff 128M offline 5 no yes
0x30000000-0x7fffffff 1.3G online 6-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
echo 0 > $sys/firmware/memory/memory5/memmap_on_memory
echo 1 > $sys/firmware/memory/memory5/config
echo 1 > $sys/devices/system/memory/memory5/online
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Alexander Gordeev:
- Compile the decompressor with -Wno-pointer-sign flag to avoid a clang
warning
- Fix incomplete conversion to flag output macros in __xsch(), to avoid
always zero return value instead of the expected condition code
- Remove superfluous newlines from inline assemblies to improve
compiler inlining decisions
- Expose firmware provided UID Checking state in sysfs regardless of
the device presence or state
- CIO does not unregister subchannels when the attached device is
invalid or unavailable. Update the purge function to remove I/O
subchannels if the device number is found on cio_ignore list
- Consolidate PAI crypto allocation and cleanup paths
- The uv_get_secret_metadata() function has been removed some few
months ago, remove also the function mention it in a comment
* tag 's390-6.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uv: Fix comment of uv_find_secret() function
s390/pai_crypto: Consolidate PAI crypto allocation and cleanup paths
s390/cio: Update purge function to unregister the unused subchannels
s390/pci: Expose firmware provided UID Checking state in sysfs
s390: Remove superfluous newlines from inline assemblies
s390/cio/ioasm: Fix __xsch() condition code handling
s390: Add -Wno-pointer-sign to KBUILD_CFLAGS_DECOMPRESSOR
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here are some small updates for tty/serial drivers for 6.18-rc1.
Not many changes overall, just the usual:
- abi cleanups and reworking of the tty functions by Jiri by adding
console lock guard logic
- 8250_platform driver updates
- qcom-geni driver updates
- other minor serial driver updates
- some more vt escape codes added
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (43 commits)
tty: serial: fix help message for SERIAL_CPM
serial: 8250: omap: Support wakeup pinctrl state on suspend
dt-bindings: serial: 8250_omap: Add wakeup pinctrl state
serial: max310x: improve interrupt handling
vt: move vc_saved_screen to within tty allocated judgment
Revert "m68k: make HPDCA and HPAPCI bools"
tty: remove redundant condition checks
tty/vt: Add missing return value for VT_RESIZE in vt_ioctl()
vt: remove redundant check on vc_mode in con_font_set()
serial: qcom-geni: Add DFS clock mode support to GENI UART driver
m68k: make HPDCA and HPAPCI bools
tty: n_gsm: Don't block input queue by waiting MSC
serial: qcom-geni: Fix off-by-one error in ida_alloc_range()
serdev: Drop dev_pm_domain_detach() call
serial: sc16is7xx: drop redundant conversion to bool
vt: add support for smput/rmput escape codes
serial: stm32: allow selecting console when the driver is module
serial: 8250_core: fix coding style issue
tty: serial: Modify the use of dev_err_probe()
s390/char/con3270: use tty_port_tty guard()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Alexander Gordeev:
- Refactor SCLP memory hotplug code
- Introduce common boot_panic() decompressor helper macro and use it to
get rid of nearly few identical implementations
- Take into account additional key generation flags and forward it to
the ep11 implementation. With that allow users to modify the key
generation process, e.g. provide valid combinations of XCP_BLOB_*
flags
- Replace kmalloc() + copy_from_user() with memdup_user_nul() in s390
debug facility and HMC driver
- Add DAX support for DCSS memory block devices
- Make the compiler statement attribute "assume" available with a new
__assume macro
- Rework ffs() and fls() family bitops functions, including source code
improvements and generated code optimizations. Use the newly
introduced __assume macro for that
- Enable additional network features in default configurations
- Use __GFP_ACCOUNT flag for user page table allocations to add missing
kmemcg accounting
- Add WQ_PERCPU flag to explicitly request the use of the per-CPU
workqueue for 3590 tape driver
- Switch power reading to the per-CPU and the Hiperdispatch to the
default workqueue
- Add memory allocation profiling hooks to allow better profiling data
and the /proc/allocinfo output similar to other architectures
* tag 's390-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (21 commits)
s390/mm: Add memory allocation profiling hooks
s390: Replace use of system_wq with system_dfl_wq
s390/diag324: Replace use of system_wq with system_percpu_wq
s390/tape: Add WQ_PERCPU to alloc_workqueue users
s390/bitops: Switch to generic ffs() if supported by compiler
s390/bitops: Switch to generic fls(), fls64(), etc.
s390/mm: Use __GFP_ACCOUNT for user page table allocations
s390/configs: Enable additional network features
s390/bitops: Cleanup __flogr()
s390/bitops: Use __assume() for __flogr() inline assembly return value
compiler_types: Add __assume macro
s390/bitops: Limit return value range of __flogr()
s390/dcssblk: Add DAX support
s390/hmcdrv: Replace kmalloc() + copy_from_user() with memdup_user_nul()
s390/debug: Replace kmalloc() + copy_from_user() with memdup_user_nul()
s390/pkey: Forward keygenflags to ep11_unwrapkey
s390/boot: Add common boot_panic() code
s390/bitops: Optimize inlining
s390/bitops: Slightly optimize ffs() and fls64()
s390/sclp: Move memory hotplug code for better modularity
...
|
|
Remove superfluous newlines from inline assemblies. Compilers use the
number of lines of inline assemblies as heuristic for the complexity
and inline decisions. Therefore inline assemblies should only contain
as many lines as required.
A lot of inline assemblies contain a superfluous newline for the last
line. Remove such newlines to improve compiler inlining decisions.
Suggested-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This patch adds a new WQ_PERCPU flag to explicitly request the use of
the per-CPU behavior. Both flags coexist for one release cycle to allow
callers to transition their calls.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
All existing users have been updated accordingly.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace kmalloc() followed by copy_from_user() with memdup_user_nul() to
improve and simplify hmcdrv_dev_write(). Remove the manual
NUL-termination.
No functional changes intended.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
To improve readability and prepare for future extensions, move the
memory hotplug code to a separate file. In addtion to it, add required
headers in sclp_mem.c and remove unnecessary headers in sclp_cmd.c
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
To improve readability, refactor sclp_cmd.c:
* Move defines and structures to the beginning.
* Reverse x-mas tree usage.
* Remove spaces after casting to eliminate checkpatch warnings.
* Remove unnecessary comments.
* Reframe certain comments.
* Convert all unsigned long long to unsigned long since unsigned long
long is a leftover from the 31/32-bit era.
* Use correct format specifiers.
* Add braces to for loops with bodies containing more than one line.
* Sort header files and remove unnecessary ones.
* Use __packed and __aligned instead of __attribute((packed,
aligned(8))) in structures.
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Tracing code called by the SCLP interrupt handler contains early exits
if the SCCB address associated with an interrupt is NULL. This check is
performed after physical to virtual address translation.
If the kernel identity mapping does not start at address zero, the
resulting virtual address is never zero, so that the NULL checks won't
work. Subsequently this may result in incorrect accesses to the first
page of the identity mapping.
Fix this by introducing a function that handles the NULL case before
address translation.
Fixes: ada1da31ce34 ("s390/sclp: sort out physical vs virtual pointers usage")
Cc: stable@vger.kernel.org
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Having the new tty_port_tty guard, use it in tty3270_resize(). This
makes the code easier to read. The winsize is now defined in the
scope and initialized immediately, so that it's obvious.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20250814072456.182853-17-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Alexander Gordeev:
- Standardize on the __ASSEMBLER__ macro that is provided by GCC and
Clang compilers and replace __ASSEMBLY__ with __ASSEMBLER__ in both
uapi and non-uapi headers
- Explicitly include <linux/export.h> in architecture and driver files
which contain an EXPORT_SYMBOL() and remove the include from the
files which do not contain the EXPORT_SYMBOL()
- Use the full title of "z/Architecture Principles of Operation" manual
and the name of a section where facility bits are listed
- Use -D__DISABLE_EXPORTS for files in arch/s390/boot to avoid
unnecessary slowing down of the build and confusing external kABI
tools that process symtypes data
- Print additional unrecoverable machine check information to make the
root cause analysis easier
- Move cmpxchg_user_key() handling to uaccess library code, since the
generated code is large anyway and there is no benefit if it is
inlined
- Fix a problem when cmpxchg_user_key() is executing a code with a
non-default key: if a system is IPL-ed with "LOAD NORMAL", and the
previous system used storage keys where the fetch-protection bit was
set for some pages, and the cmpxchg_user_key() is located within such
page, a protection exception happens
- Either the external call or emergency signal order is used to send an
IPI to a remote CPU. Use the external order only, since it is at
least as good and sometimes even better, than the emergency signal
- In case of an early crash the early program check handler prints more
or less random value of the last breaking event address, since it is
not initialized properly. Copy the last breaking event address from
the lowcore to pt_regs to address this
- During STP synchronization check udelay() can not be used, since the
first CPU modifies tod_clock_base and get_tod_clock_monotonic() might
return a non-monotonic time. Instead, busy-loop on other CPUs, while
the the first CPU actually handles the synchronization operation
- When debugging the early kernel boot using QEMU with the -S flag and
GDB attached, skip the decompressor and start directly in kernel
- Rename PAI Crypto event 4210 according to z16 and z17 "z/Architecture
Principles of Operation" manual
- Remove the in-kernel time steering support in favour of the new s390
PTP driver, which allows the kernel clock steered more precisely
- Remove a possible false-positive warning in pte_free_defer(), which
could be triggered in a valid case KVM guest process is initializing
* tag 's390-6.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (29 commits)
s390/mm: Remove possible false-positive warning in pte_free_defer()
s390/stp: Default to enabled
s390/stp: Remove leap second support
s390/time: Remove in-kernel time steering
s390/sclp: Use monotonic clock in sclp_sync_wait()
s390/smp: Use monotonic clock in smp_emergency_stop()
s390/time: Use monotonic clock in get_cycles()
s390/pai_crypto: Rename PAI Crypto event 4210
scripts/gdb/symbols: make lx-symbols skip the s390 decompressor
s390/boot: Introduce jump_to_kernel() function
s390/stp: Remove udelay from stp_sync_clock()
s390/early: Copy last breaking event address to pt_regs
s390/smp: Remove conditional emergency signal order code usage
s390/uaccess: Merge cmpxchg_user_key() inline assemblies
s390/uaccess: Prevent kprobes on cmpxchg_user_key() functions
s390/uaccess: Initialize code pages executed with non-default access key
s390/skey: Provide infrastructure for executing with non-default access key
s390/uaccess: Make cmpxchg_user_key() library code
s390/page: Add memory clobber to page_set_storage_key()
s390/page: Cleanup page_set_storage_key() inline assemblies
...
|
|
sclp_sync_wait() should use the monotonic clock for the delay loop.
Otherwise the code won't work correctly when the clock is changed.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Remove include <linux/export.h> from all files which do not contain an
EXPORT_SYMBOL().
See commit 7d95680d64ac ("scripts/misc-check: check unnecessary #include
<linux/export.h> when W=1") for more details.
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Explicitly include <linux/export.h> in files which contain an
EXPORT_SYMBOL().
See commit a934a57a42f6 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") for more details.
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
The bin_attribute argument of bin_attribute::read() is now const.
This makes the _new() callbacks unnecessary. Switch all users back.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20250530-sysfs-const-bin_attr-final-v3-3-724bfcf05b99@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- "hung_task: extend blocking task stacktrace dump to semaphore" from
Lance Yang enhances the hung task detector.
The detector presently dumps the blocking tasks's stack when it is
blocked on a mutex. Lance's series extends this to semaphores
- "nilfs2: improve sanity checks in dirty state propagation" from
Wentao Liang addresses a couple of minor flaws in nilfs2
- "scripts/gdb: Fixes related to lx_per_cpu()" from Illia Ostapyshyn
fixes a couple of issues in the gdb scripts
- "Support kdump with LUKS encryption by reusing LUKS volume keys" from
Coiby Xu addresses a usability problem with kdump.
When the dump device is LUKS-encrypted, the kdump kernel may not have
the keys to the encrypted filesystem. A full writeup of this is in
the series [0/N] cover letter
- "sysfs: add counters for lockups and stalls" from Max Kellermann adds
/sys/kernel/hardlockup_count and /sys/kernel/hardlockup_count and
/sys/kernel/rcu_stall_count
- "fork: Page operation cleanups in the fork code" from Pasha Tatashin
implements a number of code cleanups in fork.c
- "scripts/gdb/symbols: determine KASLR offset on s390 during early
boot" from Ilya Leoshkevich fixes some s390 issues in the gdb
scripts
* tag 'mm-nonmm-stable-2025-05-31-15-28' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (67 commits)
llist: make llist_add_batch() a static inline
delayacct: remove redundant code and adjust indentation
squashfs: add optional full compressed block caching
crash_dump, nvme: select CONFIGFS_FS as built-in
scripts/gdb/symbols: determine KASLR offset on s390 during early boot
scripts/gdb/symbols: factor out pagination_off()
scripts/gdb/symbols: factor out get_vmlinux()
kernel/panic.c: format kernel-doc comments
mailmap: update and consolidate Casey Connolly's name and email
nilfs2: remove wbc->for_reclaim handling
fork: define a local GFP_VMAP_STACK
fork: check charging success before zeroing stack
fork: clean-up naming of vm_stack/vm_struct variables in vmap stacks code
fork: clean-up ifdef logic around stack allocation
kernel/rcu/tree_stall: add /sys/kernel/rcu_stall_count
kernel/watchdog: add /sys/kernel/{hard,soft}lockup_count
x86/crash: make the page that stores the dm crypt keys inaccessible
x86/crash: pass dm crypt keys to kdump kernel
Revert "x86/mm: Remove unused __set_memory_prot()"
crash_dump: retrieve dm crypt keys in kdump kernel
...
|
|
There are some spelling mistakes of 'previlege' in comments which
should be 'privilege'.
Fix them and add it to scripts/spelling.txt.
The typo in arch/loongarch/kvm/main.c was corrected by a different
patch [1] and is therefore not included in this submission.
[1]. https://lore.kernel.org/all/20250420142208.2252280-1-wheatfox17@icloud.com/
Link: https://lkml.kernel.org/r/46AD404E411A4BAC+20250421074910.66988-1-wangyuli@uniontech.com
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Use strscpy() instead of strcpy() so that bounds checking is performed
on the destination buffer. This requires to keep track of the size of
the dynamically allocated prompt memory area, which is done with a new
prompt_sz within struct tty3270.
Reviewed-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The third argument of strscpy() is optional and can be left away iff
the destination is an array and the maximum size of the copy is the
size of destination.
Remove the third argument for those cases where this is possible.
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Use asm_inline for all inline assemblies which make use of the EX_TABLE or
ALTERNATIVE macros.
These macros expand to many lines and the compiler assumes the number of
lines within an inline assembly is the same as the number of instructions
within an inline assembly. This has an effect on inlining and loop
unrolling decisions.
In order to avoid incorrect assumptions use asm_inline, which tells the
compiler that an inline assembly has the smallest possible size.
In order to avoid confusion when asm_inline should be used or not, since a
couple of inline assemblies are quite large: the rule is to always use
asm_inline whenever the EX_TABLE or ALTERNATIVE macro is used. In specific
cases there may be reasons to not follow this guideline, but that should
be documented with the corresponding code.
Using the inline qualifier everywhere has only a small effect on the kernel
image size:
add/remove: 0/10 grow/shrink: 19/8 up/down: 1492/-1858 (-366)
The only location where this seems to matter is load_unaligned_zeropad()
from word-at-a-time.h where the compiler inlines more functions within the
dcache code, which is indeed code where performance matters.
Suggested-by: Juergen Christ <jchrist@linux.ibm.com>
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The check for get_zeroed_page() leads to a direct return
and overlooked the memory leak caused by loop allocation.
Add a free helper to free spaces allocated by get_zeroed_page().
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20250218034104.2436469-1-haoxiang_li2024@163.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Add check for the return value of get_zeroed_page() in
sclp_console_init() to prevent null pointer dereference.
Furthermore, to solve the memory leak caused by the loop
allocation, add a free helper to do the free job.
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20250218025216.2421548-1-haoxiang_li2024@163.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Move machine type detection to the decompressor and use static branches
to implement and use machine_is_[lpar|vm|kvm]() instead of a runtime check
via MACHINE_IS_[LPAR|VM|KVM].
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Use static branch(es) to implement and use machine_has_esop() instead
of a runtime check via MACHINE_HAS_ESOP.
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Use static branch(es) to implement and use machine_has_tlb_guest()
instead of a runtime check via MACHINE_HAS_TLB_GUEST.
Also add sclp_early_detect_machine_features() in order to allow for
feature detection from the decompressor.
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Convert MACHINE_HAS_... to cpu_has_...() which uses test_facility() instead
of testing the machine_flags lowcore member if the feature is present.
test_facility() generates better code since it results in a static branch
without accessing memory. The branch is patched via alternatives by the
decompressor depending on the availability of the required facility.
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
